Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “pseudo measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Exploring density and strength variations in asteroid 16 Psyche’s composition with 3D hydrocode modeling of its deepest impact structure

Asteroid 16 Psyche is the largest metallic Main Belt Asteroid and is the subject of a forthcoming NASA mission. The composition of Psyche is still unknown and subject of recent debate. In particular, how much porosity is within Psyche, along with how much of Psyche consists of non-metallic versus metallic materials, are central questions to the issue of Psyche’s composition. If Psyche is indeed predominantly composed of metallic materials, it would need to have considerable porosity (~ 30%–50%) for a composition consistent with its expected bulk density (~ 3.7–4.1 g/cm). In this work, we vary the density and strength of Psyche by including uniform and layered fields of pseudo-microporosity, in addition to investigating the presence of macroscopic voids, i.e., spaces larger than the size of the simulation’s mesh cells, in rubble-pile configurations. Further, all configurations result in bulk densities within the uncertainties of measured values, however the strength of Psyche and the distribution of pseudo-pores are varied. Through 3D computational models of Psyche’s deepest impact structure, we show that Psyche’s composition is unlikely to contain only pseudo-microporosity. Rather, rubble pile structures, which include macroscopic voids, are shown to match the crater’s measured aspect ratio better than simulations of structures that included only pseudo-microporosity.

3D↗
NASA NTRS1979

The mechanics of vortex pairing in a circular jet under controlled excitation

The vortex pairing phenomenon in the near field circular jet under controlled excitation is monitored by the method of phase-averaging. Hot-wire measurements were made in a 7.62 cm diameter air at Re(D) = 32,000, excited at St(D) = 0.85 with an excitation amplitude of 3%. The trajectories of the vortex centers and their longitudinal and transverse convection velocities during the pairing program are measured. Spatial distributions of the average velocity, vorticity, coherent Reynolds numbers, streamlines and pseudo-streamfunction are presented at a particular phase of the pairing. These represent field measurements at one particular time and do not involve the use of Taylor hypothesis.

Zaman, K. B. M. Q.↗
NASA NTRS1983

Particle-sampling statistics in laser anemometers Sample-and-hold systems and saturable systems

The effect of the data-processing system on the particle statistics obtained with laser anemometry of flows containing suspended particles is examined. Attention is given to the sample and hold processor, a pseudo-analog device which retains the last measurement until a new measurement is made, followed by time-averaging of the data. The second system considered features a dead time, i.e., a saturable system with a significant reset time with storage in a data buffer. It is noted that the saturable system operates independent of the particle arrival rate. The probabilities of a particle arrival in a given time period are calculated for both processing systems. It is shown that the system outputs are dependent on the mean particle flow rate, the flow correlation time, and the flow statistics, indicating that the particle density affects both systems. The results are significant for instances of good correlation between the particle density and velocity, such as occurs near the edge of a jet.

Edwards, R. V.↗
NASA NTRS2001

Viscosity Relaxation in Molten HgZnTe

Rotating cup measurements of the viscosity of the pseudo-binary melt, HgZnTe have shown that the isothermal liquid with zinc mole fraction 0.16 requires tens of hours of equilibration time before a steady viscous state can be achieved. Over this relaxation period, the viscosity at 790 C increases by a factor of two, while the viscosity at 810 C increases by 40%. Noting that the Group VI elements tend to polymerize when molten, we suggest that the viscosity of the melt is enhanced by the slow formation of Te atom chains. To explain the build-up of linear Te n-mers, we propose a scheme, which contains formation reactions with second order kinetics that increase the molecular weight, and decomposition reactions with first order kinetics that inactivate the chains. The resulting rate equations can be solved for the time dependence of each molecular weight fraction. Using these molecular weight fractions, we calculate the time dependence of the average molecular weight. Using the standard semi-empirical relation between polymer average molecular weight and viscosity, we then calculate the viscosity relaxation curve. By curve fitting, we find that the data imply that the rate constant for n-mer formation is much smaller than the rate constant for n-mer deactivation, suggesting that Te atoms only weakly polymerize in molten HgZnTe. The steady state toward which the melt relaxes occurs as the rate of formation of an n-mer becomes exactly balanced by the sum of the rate for its deactivation and the rate for its polymerization to form an (n+1)-mer.

Su, Ching-Hua↗
DOE OSTI2025

Topography restoration in white-light interferometry using an instrument transfer function evaluated with binary pseudo-random arrays

Accurate knowledge of the instrument transfer function (ITF) is vital for topography measurements using white-light interferometry (WLI). To this end, we derive a complete set of analytical expressions for the power spectral density (PSD) of a discretely sampled binary pseudo-random array (BPRA) as a theoretical benchmark. We then determine the ITF by comparing this theoretical PSD with the measured PSD of the BPRA. For the Zygo ZeGage Pro HR with a objective, the determined ITF closely matches the nominal modulation transfer function (MTF). Accordingly, we integrate the nominal MTF into Fourier-domain restoration filters and apply them to practical WLI topography data, yielding restored topographies that show improved agreement with atomic force microscopy measurements. Overall, our integrated BPRA-based ITF measurement and filtering methodology offers a robust yet practical means of characterizing WLI performance and enhancing the accuracy of surface measurements.

Hirose, Shigenobu [Japan Agency for Marine Earth S↗
DOE OSTI2024

Thermodynamic modeling of CsF with LiF-NaF-KF for molten fluoride-fueled reactors

Gibbs energy models were developed to describe the thermochemical behavior of CsF in molten FLiNaK (46.5LiF-11.5NaF-42KF mol%), a proposed molten salt reactor (MSR) fuel solvent and coolant, as cesium is of concern due to its high radiotoxicity and volatility. Initially, it was necessary to obtain a more accurate Gibbs energy function for CsF which required fitting parameters to reported vapor pressures over condensed phase CsF. The pseudo-binary systems CsF-LiF, CsF-NaF and CsF-KF were then evaluated utilizing phase equilibria and enthalpy of mixing (Δ mix H) values, together with original differential scanning calorimetry (DSC) measurements performed for the CsF-LiF and CsF-KF systems. The CsF-LiF-NaF, CsF-LiF-KF and CsF-NaF-KF pseudo-ternary system representations were obtained by interpolation of the constituent pseudo-binary systems, with DSC measurements performed for the CsF-LiF-NaF system to corroborate the calculated liquidus temperature. Ultimately, the pseudo-ternary systems were interpolated to obtain Gibbs energy models for the pseudo-quaternary CsF-LiF-NaF-KF system, supported by DSC measurements at low CsF compositions (1–10 mol%), yielding computed equilibria and cesium-containing vapor pressures that compare favorably with reported values. In conclusion, the Molten Salt Thermal Properties Database – Thermochemical (MSTDB-TC) was subsequently expanded to include these Gibbs energy models allowing description of the thermochemical behavior of the CsF-LiF-NaF-KF system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Imaging Power Losses in CdSeTe Solar Cells

Much of the research on CdSeTe photovoltaics is focused on improving the open-circuit voltage (V oc ) of the solar cell. But solar cells operate at the maximum power point (MPP) rather than at V oc . The recombination processes at MPP may be different than those at V oc , and increasing the power output at MPP is the key to advancing efficiency. Here, we introduce a camera-based PL imaging system that enables power loss analysis under operating conditions and across cm-sized areas covering multiple cells. The instrument is demonstrated with CdSeTe devices having efficiencies greater than 19%. An implied current density versus implied voltage (iJV) curve can be produced at each pixel with <20 µm resolution. We find that regions with high implied open circuit voltage are often those with low implied fill factor, showing that voltage loss analysis at open circuit is not sufficient to understand power losses under operating conditions. Measurement of JV curves as a function of irradiance can also be performed in the system, which allows series resistance-free pseudo JV (pJV) curves to be produced. Comparison of pJV to measured JV and iJV curves allows further analysis of the operational losses, pointing the way to higher efficiency.

14 SOLAR ENERGY↗
DOE OSTI2020

Damage Pseudo Cross Section Generator

This software is a python script for generating group damage pseudo-cross-sections for specific elements, and tabulating them in forms useful to python or to office-open workbooks (xlsx). The damage pseudo-cross-section is needed for calculating how much neutron radiation damage a structural material receives in a reactor measured in displacements per atom (DPA). The process of generating these pseudo-cross-sections is laborious as it requires running the nuclear data processing code, NJOY, for hundreds of isotopes, and then post-processing the data. This also allows many opportunities for human error to be involved. This script eliminates these problems by fully automating the process.

Gale, MicahD.↗
NASA NTRS2005

Hubble Space Telescope Angular Velocity Estimation During the Robotic Servicing Mission

In 2004 NASA began investigation of a robotic servicing mission for the Hubble Space Telescope (HST). Such a mission would require estimates of the HST attitude and rates in order to achieve a capture by the proposed Hubble robotic vehicle (HRV). HRV was to be equipped with vision-based sensors, capable of estimating the relative attitude between HST and HRV. The inertial HST attitude is derived from the measured relative attitude and the HRV computed inertial attitude. However, the relative rate between HST and HRV cannot be measured directly. Therefore, the HST rate with respect to inertial space is not known. Two approaches are developed to estimate the HST rates. Both methods utilize the measured relative attitude and the HRV inertial attitude and rates. First, a nonlinear estimator is developed. The nonlinear approach estimates the HST rate through an estimation of the inertial angular momentum. The development includes an analysis of the estimator stability given errors in the measured attitude. Second, a linearized approach is developed. The linearized approach is a pseudo-linear Kalman filter. Simulation test results for both methods are given, including scenarios with erroneous measured attitudes. Even though the development began as an application for the HST robotic servicing mission, the methods presented are applicable to any rendezvous/capture mission involving a non-cooperative target spacecraft.

Thienel, Julie K.↗
NASA NTRS2007

Roller Bearing Health Monitoring Using CPLE Frequency Analysis Method

This paper describes a unique vibration signature analysis technique Coherence Phase Line Enhancer (CPLE) Frequency Analysis - for roller bearing health monitoring. Defects of roller bearing (e.g. wear, foreign debris, crack in bearing supporting structure, etc.) can cause small bearing characteristic frequency shifts due to minor changes in bearing geometry. Such frequency shifts are often too small to detect by the conventional Power Spectral Density (PSD) due to its frequency bandwidth limitation. This Coherent Phase Line Enhancer technology has been evolving over the last few years and has culminated in the introduction of a new and novel frequency spectrum which is fully described in this paper. This CPLE technology uses a "key phasor" or speed probe as a preprocessor for this analysis. With the aid of this key phasor, this CPLE technology can develop a two dimensional frequency spectrum that preserves both amplitude and phase that is not normally obtained using conventional frequency analysis. This two-dimensional frequency transformation results in several newly defined spectral functions; i. e. CPLE-PSD, CPLE-Coherence and the CPLE-Frequency. This paper uses this CPLE frequency analysis to detect subtle, low level bearing related signals in the High Pressure Fuel Pump (HPFP) of the Space Shuttle Main Engine (SSME). For many rotating machinery applications, a key phasor is an essential measurement that is used in the detection of bearing related signatures. There are times however, when a key phasor is not available; i. e. during flight of any of the SSME turbopumps or on the SSME High Pressure Oxygen Turbopump (HPOTP) where no speed probe is present. In this case, the CPLE analysis approach can still be achieved using a novel Pseudo Key Phasor (PKP) technique to reconstruct a 1/Rev PKP signal directly from external vibration measurements. This paper develops this Pseudo Key Phasor technique and applies it to the SSME vibration data.

Jong, Jen-Yi↗
DOE OSTI2023

Risk Ratio and Risk Difference Estimation in Case-cohort Studies

Background: In case-cohort studies with binary outcomes, ordinary logistic regression analyses have been widely used because of their computational simplicity. However, the resultant odds ratio estimates cannot be interpreted as relative risk measures unless the event rate is low. The risk ratio and risk difference are more favorable outcome measures that are directly interpreted as effect measures without the rare disease assumption. Methods: We provide pseudo-Poisson and pseudo-normal linear regression methods for estimating risk ratios and risk differences in analyses of case-cohort studies. These multivariate regression models are fitted by weighting the inverses of sampling probabilities. Also, the precisions of the risk ratio and risk difference estimators can be improved using auxiliary variable information, specifically by adapting the calibrated or estimated weights, which are readily measured on all samples from the whole cohort. Finally, we provide computational code in R (R Foundation for Statistical Computing, Vienna, Austria) that can easily perform these methods. Results: Through numerical analyses of artificially simulated data and the National Wilms Tumor Study data, accurate risk ratio and risk difference estimates were obtained using the pseudo-Poisson and pseudo-normal linear regression methods. Also, using the auxiliary variable information from the whole cohort, precisions of these estimators were markedly improved. Conclusion: The ordinary logistic regression analyses may provide uninterpretable effect measure estimates, and the risk ratio and risk difference estimation methods are effective alternative approaches for case-cohort studies. These methods are especially recommended under situations in which the event rate is not low.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1976

Absolute rate parameters for the reaction of atomic hydrogen with hydrazine

Absolute rate parameters for the reaction of atomic hydrogen with hydrazine H + N2H4 yields H2 + N2H3 have been determined in a direct manner using flash photolysis of dilute mixtures of hydrazine in helium and time dependent observation of H via resonance fluorescence. By measuring the H-atom decay under pseudo-first-order conditions, the bimolecular rate constant K sub 1 was obtained over the temperature range 228-400 K. The data were fitted with good linearity to the Arrhenius expression K sub 1 = (9.87 plus or minus 1.17) x 10 to the -12th exp(-2380 plus or minus 100/RT) cu cm/molecule/s. The data were shown to be free of any contributions from secondary reactions involving H as a reactant or product.

Stief, L. J.↗
NASA NTRS1983

Design of the stift time and frequency transfer microwave ground terminal

The Satellite Time and Frequency Transfer System is intended to provide, simultaneously, global time comparisons at the subnanosecond level and frequency comparisons to better than 1 part in 10 to the 14th power. It utilizes an orbiting hydrogen maser clock and frequency standard that communicates, via microwave links, time and frequency information to Earth terminals operated by hydrogen masers controlling local clocks. A two-way microwave link, to and from the space vehicle provides Doppler information used to cancel the Doppler shifts in a one-way link from the spaceborne oscillator. Pseudo-random noise (PRN) modulation in the two-way link also provides range information to cancel the range delay in the PRN time transfer between space and Earth. The pseudo-random noise modulation system for time difference measurement and its incorporation in the Doppler cancellation system for frequency comparison is explained. The particular PRN code sequence selected and an analysis of the system is discussed.

Penfield, H.↗
NASA NTRS1986

Spinning disk calibration method and apparatus for laser Doppler velocimeter

A method and apparatus for calibrating laser Doppler velocimeters having one or more intersecting beam pairs are described. These velocimeters measure fluid velocity by observing the light scattered by particles in the fluid stream. Moving fluid particulates are simulated by fine taut wires that are radially mounted on a disk that is rotated at a known velocity. The laser beam intersection locus is first aimed at the very center of the disk and then the disk is translated so that the locus is swept by the rotating wires. The radial distance traversed is precisely measured so that the velocity of the wires (pseudo particles) may be calculated.

Snyder, P. K.↗
NASA NTRS2016

Evaluation of the Effect of Surface Finish on High-Cycle Fatigue of SLM-IN718

The surface finish of parts produced by additive manufacturing processes is much rougher than the surface finish generated by machining processes, and a rougher surface can reduce the fatigue strength of a part. This paper discusses an effort to quantify that reduction of strength in high-cycle fatigue for selective laser melt (SLM) coupons. A high-cycle fatigue (HCF) knockdown factor was estimated for Inconel 718, manufactured with the SLM process. This factor is the percentage reduction from the maximum stress in fatigue for low-stress ground (LSG) specimens to the maximum stress of those left with the original surface condition at the same fatigue life. Specimens were provided by a number of vendors, free to use their "best practice"; only one heat treat condition was considered; and several test temperatures were characterized, including room temperature, 800F, 1000F, and 1200F. The 1000F data had a large variance, and was omitted from consideration in this document. A first method used linear approximations extracted from the graphs, and only where data was available for both. A recommended knockdown factor of the as-built surface condition (average roughness of approximately 245 micro-inches/inch) versus low-stress ground condition (roughness no more than 4 micro-inches/inch) was established at approximately 1/3 or 33%. This is to say that for the as-built surface condition, a maximum stress of 2/3 of the stress for LSG can be expected to produce a similar life in the as-built surface condition. In this first evaluation, the knockdown factor did not appear to be a function of temperature. A second approach, the "KP method", incorporated the surface finish measure into a new parameter termed the pseudo-stress intensity factor, Kp, which was formulated to be similar to the fracture mechanics stress intensity factor. Using Kp, the variance seemed to be reduced across all sources, and knockdown factors were estimated using Kp over the range where data occurred. A plot of the results suggests that the knockdown factor is a function of temperature, and that for low lives the knockdown might be lower than the knockdown observed above about one million cycles, where it tended to stabilize. This was not universal for all temperatures tested. The higher temperature tests are thought to be influenced by the test temperature, which perhaps continued the aging process. Further evaluation of the method is suggested.

Lambert, D. M.↗
NASA NTRS1982

Ultrasonic measurement of axial stress

The theory of acoustic propagation in strained media is examined, with particular emphasis on rod (bolt) geometries. The continuous wave (CW) approach is the basis of the study, and the theory is developed from a frequency domain analysis standpoint in order to obtain an applied stress/normalized frequency shift relationship. CW measurements may be influenced by such factors as propagation effects, mode conversion, frequency, material properties, and geometry. After the first loading cycle, axial stress measurements for a preloading with an initial frequency of 4.995 36 MHz dropped to 4.989 19 MHz, indicating a 6.17 kHz change. CW and pseudo-CW ultrasonic techniques are found to be reliable for axial stress measurements, and acoustic attenuation measurements correlated to residual stress fields may possibly involve transducer phase cancellation. It is thus concluded that signal drop is an artifact of the transducer directivity, rather than an actual acoustic power decrease.

Heyman, J. S.↗
DOE OSTI2023

Enhanced neutrino polarizability

We point out that neutrinos can have enhanced couplings to photons, if light (pseudo)scalar mediators are present, resulting in a potentially measurable neutrino polarizability. We show that the expected suppression from small neutrino masses can be compensated by the light mediator mass, generating dimension 7 Rayleigh operators at low scales. We explore the rich phenomenology of such models, computing in detail the constraints on the viable parameter space, spanned by the couplings of the mediator to neutrinos and photons. Finally, we build several explicit models that lead to an enhanced neutrino polarizability by modifying the inverse see-saw majoron, i.e., the pseudo-Nambu-Goldstone boson of the U(1) L global lepton number responsible for generating small neutrino masses.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1979

Advanced methods for preparation and characterization of infrared detector materials

Crystal growth of Hg sub 1-x Cd sub x Te and density measurements of ingot slices are discussed. Radial compositional variations are evaluated from the results of infrared transmission edge mapping. The pseudo-binary HgTe-CdTe phase diagram is examined with reference to differential thermal analysis measurements. The phase equilibria calculations, based on the 'regular association solution' theory (R.A.S.) are explained and, using the obtained R.A.S. parameters, the activities of Hg, Cd, and Te vapors and their partial pressures over the pseudo-binary melt are calculated.

Lehoczy, S. L.↗