Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compression molding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗
DOE OSTI2025

Sizing comingled CF/PA 6 fibers with cellulose nanofibrils for enhanced performance properties

Compatibility between the reinforcing phase and the polymer matrix is critical to achieving the desired mechanical and thermal performance of composite materials. Several mechanisms can enhance this interfacial interaction, including surface treatments (e.g., oxidation, plasma, or irradiation), in-situ nanoparticle deposition, and fiber sizing. Here, in this study, cellulose nanofibrils (CNF) were employed as a sustainable sizing agent to modify the interface in commingled carbon fiber (CF)/polyamide 6 (PA 6) yarns, in which CF and PA6 filaments are intimately blended to enable simultaneous consolidation. A 0.25 wt% CNF aqueous suspension was applied under bath sonication to ensure uniform dispersion and minimize agglomeration. CNF-sized and unsized yarns were used to fabricate unidirectional composite plates via filament winding on a flat mandrel, followed by compression molding. Scanning electron microscopy confirmed CNF presence on both CF and PA6 filaments. CNF-sized composites exhibited increments in interlaminar shear strength (ILSS) by 50%, flexural strength by 11%, and tensile strength by 2.5% compared to unsized composites. Thermal analysis showed minimal changes in degradation temperature and crystallinity. These findings demonstrate that CNF sizing enhances interfacial bonding and mechanical performance, offering a scalable and environmentally friendly strategy for thermoplastic composite manufacturing along with yarn/tow handleability.

Cellulose nanofibrils (CNF)↗
DOE OSTI2023

Bending and shear improvements in 3D-printed core sandwich composites through modification of resin uptake in the skin/core interphase region

Fused deposition modeling (FDM) printed polymers are rarely used as a structural material due to anisotropic and low mechanical properties compared with conventional composites. In recent years, greater need has been expressed for recycling of materials, such as recyclable FDM, at the end of service life to reduce environmental pollution and manufacture cost. However, how the amount of resin uptake in the skin and skin/core interphase affects the bending and shear performance of the sandwich composites when replacing the low strength and ductile core (conventional core) with a high strength and brittle core (FDM printed PLA (polylactic acid) core) still remains unclear. A new manufacturing routine is needed to improve the incorporation of FDM printed polymers in composite structures. In this work, FDM printed PLA was used as core material and sandwiched between two unidirectional glass fiber reinforced polymer (GFRP) skins to form a sandwich composite by compression-molding (CM) process, which provides a good manufacturing strategy for skin/core interphase modification. The significance of the CM process is proved by investigating the effect of resin uptake on bending and in-plane/out-of-plane shear performances. Current first order shear deformation (FSDT) theory lacks a direct connection between the in-plane shear stress and out-of-shear stress in the core region of sandwich composites. With the help of DIC, a connection between the in-plane shear and the out-of-plane shear strain was built and in-plane shear properties can acquire through out-of-plane shear properties, hence reducing the redundancy of sample preparation or the need for simulation. A significant improvement was found compared with the optimized resin uptake (Optimized resin uptake range: 20.43%–22.86 wt%) 3D-printed PLA core sandwich composite and lowest performance sandwich composite (Improvement: in-plane shear strength (~34%)/modulus (~29%), out-of-plane shear strength (~25%)/modulus (~31%), specific peak bending load (~19%)). Finally, compared with balsa core sandwich composites, the 3D-printed cores are suitable for use in composite sandwich structures in many applications with a satisfactory strength-to-weight ratio.

3D-printed core sandwich composite↗
DOE OSTI2020

Internal arcing and lightning strike damage in short carbon fiber reinforced thermoplastic composites

Short carbon fiber reinforced thermoplastic composites (S-CFRTP) are currently used in interior parts of aircraft such as electronic circuitry and assemblies, and their usage in aircraft's exterior is also being studied. In this paper, we present a lightning strike study on S-CFRTPs. High performance thermoplastics such as a polyphenylene sulfide (PPS) reinforced with 50% weight (wt.) short carbon fiber (CF), a polyphenyl sulfone (PPSU) reinforced with 25 % wt. Short CF and a acrylonitrile butadiene styrene (ABS) with 20 % wt. short CF were tested against artificial lightning strikes. All samples were prepared using an extrusion compression molding (ECM) technique. A modified component A (100 kA) of lightning waveform, as defined by SAE ARP 5412-B, was applied. High speed imaging, thermography, scanning electron microscopy (SEM) and ultrasonic non-destructive evaluation were performed to understand the effect of lightning strikes on the thermoplastic panels. The results show that electrical conductivity of the composite, thermal stability of the polymers, and CF orientation significantly affected the damage from artificial lightning strikes. PPS composite had the highest resilience against lightning strike damage, retaining 95% and 89% residual flexural strength and modulus, respectively. CF exfoliation due to internal arcing was observed in the carbon fiber-reinforced ABS polymer (CF-ABS) composite. CF exfoliation damage has been reported for the first time.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dry-pressed lithium nickel cobalt manganese oxide (NCM) cathodes enabled by holey graphene host

There is an increasing demand for electric vehicle batteries with higher energy densities that can be manufactured with low cost utilizing environmentally friendly processes. Lithium nickel cobalt manganese oxides (NCM), such as LiNi(0.5)Co(0.2)Mr(0.3)O(2) (NCM523), are commonly used in commercial lithium ion batteries for electric vehicle applications. These cathodes are typically fabricated using environmentally hazardous, energy intensive, and time-consuming solvent-based slurry casting processes. Polymeric binders, also required for cathode preparation, add weight and can undergo parasitic reactions during battery cycling. Here we report a facile, solvent-free, binder-free, and rapid cold-press electrode fabrication process to prepare high mass loading NCM cathodes within minutes. This process is enabled by the use of holey graphene, a unique lightweight, compressible carbon nanomaterial that serves as both a binder and an electrically conductive matrix. NCM cathodes fabricated by this method are stable and exhibit good active material utilization. A significant advantage for the dry-press process is that the electrode mass loadings can be readily increased simply by adding more composite powder to the compression molding die, resulting in improved areal capacities that are attractive for applications requiring high energy per unit footprint. (C) 2020 Elsevier Ltd. All rights reserved.

25 ENERGY STORAGE↗
DOE OSTI2021

Performance of hybridized bamboo-carbon fiber reinforced polypropylene composites processed using wet laid technique

The end-of-life vehicles (ELV) regulations motivate hybrid materials usage in automotive industries to optimize properties at reduced cost and increase eco-friendly designs. This research explores hybrid compositions of natural bamboo fiber and synthetic carbon fiber. The goal of hybridization was to synergistically benefit from each constituent– i.e., sustainability, energy absorption and superior damping from bamboo, and high strength and stiffness from carbon fiber. Carbon fibers (CF), bamboo fibers (BF) and polypropylene (PP) fibers were dispersed in water to produce wet-laid hybrid mats. The mats were compression molded into consolidated panels to obtain the hybrid composite(s) (BF-CF-PP). Four formulations with different fiber-resin weight percent were designed and produced including- BF-PP (30/70), BF-PP (50/50), BF-CF-PP (32/8/60), and BF-CF-PP (8/32/60). The effect of (a) fiber length, (b) surface treatment, (c) fiber content, and (d) consolidation pressure on the mechanical properties were examined. The improved mechanical (flexural strength 76.4 MPa, flexural modulus 4.1 GPa, ILSS 12.4 MPa and impact strength 49.9 KJ/m 2 ) and vibrational damping (1.05%) properties showed that the BF-CF-PP (8/32/60) provided higher properties compared to the other variants. The projected properties at various stoichiometric ratios of carbon and bamboo fiber revealed that the properties of hybrid composites could be tailored to produce desirable, cost-effective, and sustainable automotive components.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Long coir and glass fiber reinforced polypropylene hybrid composites prepared via wet-laid technique

Natural fiber composites offer an advantage in terms of weight saving for many automotive applications; however, many natural fiber composites lack properties to justify substitution for synthetic composites. Hybridizing the natural fiber composites by adding a fraction of synthetic fibers is an innovative approach to provide a balance between composite's performance and weight savings. In this study, coir fiber (40 wt%)-reinforced polypropylene (PP) composites were hybridized by substituting a fraction of coir fiber with glass fiber (0–30 wt%). The composites were prepared using a novel wet-laid technique followed by compression molding, where the fiber length is preserved. The composites prepared by hybridizing PP/coir fibers with glass fibers were light in weight (6–20% lighter compared to 40 wt% glass fiber reinforced PP) with significantly enhanced tensile (strength – 49–182%, modulus – 54–130%), flexural (strength – 41–104%, modulus – 64–193%), and impact properties (157 - 474%) compared to 40 wt% coir fiber reinforced PP composites. Furthermore, the addition of glass fiber (10–30 wt%) to coir fiber reduced the water-absorbing tendency (by 18–74%) of PP/coir fiber composites. All in all, this work has potential applications in automotive, mass transit, and truck applications where natural fiber composites are being investigated as alternatives to metal and/or fully synthetic composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of processing temperature, pressure, and fiber volume fraction on mechanical and morphological behaviors of fully-recyclable uni-directional thermoplastic polymer-fiber-reinforced polymers

This work explores a type of composite called thermoplastic polymer-fiber-reinforced polymers (PFRPs), often referred to as self-reinforced composites (SRCs). A representative PFRP was exemplified using unidirectional (UD) ultra-high-molecular-weight polyethylene (UHMWPE) fibers embedded in a high-density polyethylene (HDPE) matrix. The effects of compression molding temperature and pressure on the mechanical and morphological behaviors of the filament-wound PFRPs with various fiber volume fractions (V f ) were experimentally investigated. The results elucidate the evolution of morphologies and tensile properties of the PFRPs due to thermal melting, fiber misalignment from pressure, and (V f )-induced structural variance, which has not been comprehensively reported yet. The highest specific tensile strength and modulus of the PFRP laminae reach 600 MPa/(g/cm 3 ) and 31 GPa/(g/cm 3 ), respectively. These properties are comparable to glass-/aramid-fiber-reinforced polymers (GFRPs, GFRTPs, AFRPs, and AFRTPs), with PFRPs exhibiting better ductility (specific strain at peak load ≈ 4%/(g/cm 3 )) than other common polymer composites. The motivation for this work was the high recyclability of PFRPs, which can be recycled by melting both the fibers and the matrix, and then reshaped them for re-manufacturing composites to maximize the efficiency in material reuse. This process simplifies the implementation of closed-loop recycling, re-manufacturing, and reuse to support sustainability in composites. This work aims to contribute to advancing thermoplastic PFRPs for their potential applications in various industries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Infrared thermography NDT for in-situ defect detection in sandwich composite panel manufacturing

Composite manufacturing presents numerous challenges, as defects can arise from various sources throughout the process. In sandwich composite structures, the integration of a foam core introduces additional complexity and increases the likelihood of defect formation like delamination. To mitigate these issues and reduce the risk of future structural failures, in-situ monitoring during manufacturing is essential. This study investigates infrared (IR) thermography as a non-destructive technique for detecting manufacturing defects in foam-core sandwich composite panels under thermally excited conditions representative of in-situ processing. A stationary FLIR A8590 IR camera (640 × 512 pixels, 30Hz, 17mm lens, 9 ft stand-off distance) was used to monitor prefabricated panels subjected to controlled external heating simulating compression molding and resin cure exotherm. Interlaminar delamination defects with characteristic sizes ranging from 0.25 × 0.25in² to 5 × 5in² produced measurable surface temperature depressions of approximately 4–10°C during transient cooling, exceeding the effective noise floor of the camera by more than two standard deviations. Thicker laminates exhibited prolonged defect detectability windows due to increased thermal diffusion time. In contrast, embedded Teflon inclusions generated weak thermal contrasts of ≤ 3°C, approaching the measurement noise floor, due to limited thermal property contrast with the surrounding glass fiber composite. These results establish quantitative detectability limits for stationary thermographic inspection of sandwich composite panels under manufacturing-representative thermal cycles.

Barakat, Abdallah [ORNL] (ORCID:0000000296141398)↗
DOE OSTI2020

Characterization of textile-grade carbon fiber polypropylene composites

In this work, we consider low-cost carbon fiber produced with a textile-grade precursor. The objective of the study is to investigate textile-grade carbon-fiber-reinforced-polypropylene composites (TCF-PP) from compounded pellets for mechanical and thermal characterization. Four sets of pellets with 1%, 5%, 10%, and 15% reinforcement were manufactured using textile-grade carbon fiber (TCF) and polypropylene (PP) by twin-screw compounding. The addition of TCFs through gravimetric feeder directly in the extruder resulted in lower fiber content; however, side feeder has shown good potential. The pellets were further processed in extrusion compression molding to manufacture plaques. An increase in fiber loading has a negligible effect on fiber attrition as fiber length distribution variation between 1% and 15% reinforced pellets was very small. The addition of TCFs in PP showed a significant improvement in mechanical properties. The tensile strength and modulus of the composite were 26% and 161%, respectively, improved by the addition of 10 wt% TCF. Similar results were observed in the flexure test. However, the impact properties were reduced by 25.54% by the addition of 15% TCF.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Discontinuous Aligned Carbon Fiber Intermediates for Automotive and Related Applications

This work focused on preferentially aligning discontinuous carbon fibers in wet-laid or air-laid processes. It is well known that aligned fibers provides higher directional strength and stiffness. Discontinuous fibers further allow higher degree of draw and formability as the gaps in the fibers allow for higher material movement. The current processes are limited in their ability to align carbon fibers during processing. The aligned fibers have several benefits - (a) in applications where chopped fibers can replace continuous fibers for targeted strength and stiffness metrics, but at a substantially reduced cost; (b) they can tolerate deeper draws than continuous fiber composites in thermo-stamping and compression molding processes; (c) they can be tailored for pultrusion and unidirectional applications. Although pultrusion is primarily a process that adopts continuous fibers, stitch bonded entangled discontinuous fibers can provide unique intermediates. This is analogous to natural coir fibers which get aligned and entangled to produce ropes/rods for example, (d) they can be processed in cross-ply and multi-directional formats, like composite laminates. In this work Neenah Paper partnered with IACMI, UT and ORNL to evaluate structure-process-property relationships with Zoltek carbon fiber. A few process parameters such as machine speed, weight basis, fiber length, effect of fiber sizing, direction of mat lay-up etc. were investigated. The produced mats were converted to thermoplastic composite laminates using polyamide 6 (PA6, nylon) resin. The specific objective of this project is to produce a wet-laid nonwoven carbon fiber mat with a high degree of unidirectional fiber alignment, using discontinuous carbon fibers. The report provides details about the processing, characterization, and lower-upper bound properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

LightMAT: Continous Fiber Malleable Thermoset Composites with sub-1-minute dwell times; validation of impact performance and evaluation of the efficacy of the compression forming process

Recent major advances in polymer chemistry are enabling a paradigm shift in the area of processing and re-processing/recycling of advanced composite materials. Inexpensive compression molding with short cycle times, traditionally available for thermoplastic composites only, are now possible for the thermoset resins based on polyimine chemistry. Participant will collaborate with the LightMAT consortium Labs ORNL, SNL, and PNNL to non-destructively characterize microscopic structural defects (such as voids and resin-rich areas), and perform high speed impact characterization of its malleable thermoset CFRP's. This work is critical to the validation and adoption of these materials for the automotive market and towards DOE-VTO lightweighting mission objectives.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The mechanical properties of Kel-F 800 (FK-800) as a function of crystallinity

Kel-F 800 is a copolymer of chlorotrifluoroethylene PTFE (75 wt. %) and vinylidene fluoride PVDF (25 wt. %). It has previously been used as a PBX binder for insensitive explosives such as PBX 9502 and LX-17. 3M started production of Kel-F 800 in 1957 and small-scale batches continued to be made until 2002 when production ceased due to environmental concerns regarding one of the emulsifiers used during production. Around 2000 the Kel-F 800 name was changed to FK-800 to avoid trademark concerns because rights to produce another polymer with a similar tradename (Kel-F 81) had been sold to another manufacturer. The Kel designation came from the original manufacturer of PCTFE (Kel-F 81), the Kellog company. To avoid confusion this document will only refer to Kel-F 800. In 2006, production of small-scale batches of Kel-F 800 was started again by 3M in response to customer enquiries. This new material, the first blended batch is referred to as LOT 1, was produced with a different emulsifier than used previously. Because Kel-F 800 is made in a small batch reactor, considerable variation in crystallinity can be expected from lot to lot and year to year. In many ways, this is not significant since the material is dissolved in a solvent (often MEK, ethylmethyl ketone or ethyl acetate) for PBX production purposes. This destroys the as received crystallinity and the resulting crystallinity in the processed material is a function of polymer molecular weight and thermal history. Producing large billets of Kel-F 800 from solvent extraction is not practical and so a compression molding technique has been used above the melting temperature. This method also removes residual crystallinity from the supplied granules. The molecular weight of a polymer can be estimated by several techniques, the most common being gel permittivity chromatography (GPC), size exclusion chromatography (SEC) and shear rheometry measurements of polymer/solvent solutions. Changes in molecular weight will affect the crystallization rate and the maximum crystallinity reached for a specific thermal history. Both references agree that the new LOT 1 material molecular weight falls within the deviation found from averaging previous historical lots of Kel-F 800.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Fully Recyclable CFRP Particles (CRADA 519)

The proposed resin-enhanced materials, which utilize fully recycled CFRP (carbon-fiber-reinforced polymer) particles, are enabled by PARC's proprietary Chemically Linked Particles Networks (13 granted patents and patent applications). PNNL and PARC have collaborated to develop manufacturing methods, such as vacuum-assisted wet compression molding and filament winding, for fabricating fiber-reinforced composites with the PARC matrix. PNNL has conducted various mechanical, physical, and thermal characterizations to compare their differences between the composites with baseline and PARC matrices. Those characterizations include density, void volume fraction, optical micrography, uniaxial tension, four-point bending/flexure, interlaminar shear, coefficient of thermal expansion, glass transition temperature, and curing kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Demonstration of high-rate manufacturing of π-joint using additive manufacturing

Bonded composite π-joints are critical to support wing geometries in aerospace/aircraft structures. Its lightweight and robust load-bearing capabilities/design guarantee high structural integrity and reliability. Current manufacturing techniques of π-joints are complex and laborious, and do not always offer high-quality joining. This study presents a high-rate manufacturing approach to fabricate π-joints using an integrated Additive Manufacturing and Compression Molding (AMCM) process. The joints were manufactured using unidirectional aerospace-grade LMPAEK/CF at 60% fiber loading for the stiffeners/skin and LM-PAEK/GF as the adhesive and characterized to evaluate their microstructure and strength. While the results indicate void formation at the joint caused by inadequate pressure, the peak tensile load of 600N recorded is akin to injection-autoclave molded π-joints, which validates the potential of this high-rate integrated approach to eliminate time-consuming and labour-intensive processes of making π-joints to reduce cost and produce high-quality joints.

Marathe, Umesh [ORNL]↗
DOE OSTI2023

Recycled Glass Polypropylene Composites from Transportation Manufacturing Waste

In recent years there has been growing interest in developing recycling technologies for composites manufacturing scrap, process waste and end-of-life parts. The focus of this work was to establish processing routes and mechanical property bounds for glass-polypropylene (PP-GF) scrap from the production of parts for truck trailers, automobiles, and rail cars. This study considered PP-GF scrap and demonstrated extrusion-compression molding (ECM) as a viable route for the closed-loop manufacture of composite parts. The results were promising in terms of the strength and modulus retention of the PP-GF recyclate. The tensile strength and modulus was the highest for 50% and 66% recycled content, compared with 100% and 83% recycle content. The flexural strength and modulus of the 100% and 83% recycled compositions was higher than the 66% and 50% recycled content, respectively. The impact energy absorption of the PP-GF recyclate at at all fiber loadings was superior in absorbing energy compared with the incumbent (benchmark) plywood. This work is useful to designers seeking to incorporate recycled materials in their products.

Vaidya, Uday↗
DOE OSTI2024

Cellulose Nanofibrils Dewatered with Poly(Lactic Acid) for Improved Bio-Polymer Nanocomposite Processing

Cellulose nanofibrils (CNFs) have theoretically ideal properties for bio-based composite applications; however, the incorporation of these materials into polymers is made challenging by the strong binding of water to CNFs and the irreversible agglomeration of CNFs during drying. Previous methods used “contact dewatering”, wherein the addition of wood flour (WF) to CNFs facilitated the mechanical removal of water from the system via cold pressing, which showed potential in producing dried CNF fibrils attached to wood fibers for biocomposite applications. In this work, the viability of contact dewatering with poly(lactic) acid (PLA) powder for PLA/CNF composites was evaluated. The energy efficiency of dewatering, preservation of nanoscale CNF morphology, and mechanical properties were examined by mixing wet CNFs with pulverized PLA at various loading levels, pressing water out of the system, and compression molding and shear mixing composites for testing. The most impressive results from this dewatering method were the preservation of micron-to-nanoscale fibers with high aspect ratios in PLA-CNF composites; increased strength and modulus of 1.7% and 4.2%, respectively, compared to neat PLA; equivalent or better properties than spray-dried nanocellulose at similar loading levels; and an 11-194x reduction in drying energy compared to spray-drying CNFs.

Chemistry↗
DOE OSTI2025

Bacterial-Retted Hemp Fiber/PLA Composites

The push for sustainability in all facets of manufacturing has led to an increased interest in biomass as an alternative to non-renewable materials. Hemp bast fiber mats were produced from a bacterial retting process, named BFM, as the fiber reinforcement. The objective of this study was to evaluate the feasibility of laminating BFM with polylactic acid (PLA) for a composite panel product. Since both BFM and PLA are biodegradable, the resulting BFM-PLA composites will be 100% biodegradable. PLA pallets were processed into thin polymer sheets which served as the matrix. The BFM and PLA plates were laminated in five layers and compression-molded into composite panels. Experiments were conducted on the three BFM-to-PLA ratios (35/65, 45/55, and 50/50). Mechanical properties (tensile and bending properties) and physical properties (thickness swell and water absorption) were tested and compared to the currently commercial sheet molding compound (SMC) from fiber glass. The thermal behavior of the BFM/PLA composites was characterized using dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC). The developed BFM/PLA composite product is a sustainable alternative to existing synthetical fiber-reinforced polymer (FRP) that is biodegradable in landfill at the end of life.

Smith, Lee M. (ORCID:0000000264390357)↗