Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHITE NOISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Image discrimination models predict detection in fixed but not random noise

By means of a two-interval forced-choice procedure, contrast detection thresholds for an aircraft positioned on a simulated airport runway scene were measured with fixed and random white-noise masks. The term fixed noise refers to a constant, or unchanging, noise pattern for each stimulus presentation. The random noise was either the same or different in the two intervals. Contrary to simple image discrimination model predictions, the same random noise condition produced greater masking than the fixed noise. This suggests that observers seem unable to hold a new noisy image for comparison. Also, performance appeared limited by internal process variability rather than by external noise variability, since similar masking was obtained for both random noise types.

NASA Center ARC↗
NASA NTRS2018

ATMS Radiometric Noise Characterization

The Advanced Technology Microwave Sounder (ATMS), on SNPP and NOAA-20, provides vertical atmospheric temperature and moisture profiles that are a key input to numerical weather prediction. Full characterization of radiometric noise is critical to error modeling, algorithm development and the potential development of performance requirements and product improvements. This paper presents estimates of white noise and low-frequency 1/f noise as derived from the Allan variance and scan-to-scan autocorrelations of data from the internal hot calibration. This approach allows direct comparison of on-orbit performance of the two units as well as comparison between ground calibration test data and on-orbit performance. The autocorrelation at multiple scan intervals is used as input to a theoretical model of the NET of inferred scene brightness temperature, when using weighted samples of calibration data over multiple scans. This will support selection of optimized calibration weighting functions for each channel, as well as providing further insight into the striping phenomenon. These measured autocorrelations are also compared to the autocorrelations derived from the 1/f spectra obtained both in special ground and on-orbit tests that characterize gain fluctuation. Channel cross-correlations are also presented, which can have a significant impact on effectiveness of direct assimilation performance.

instrument calibration↗
NASA NTRS1978

Signal detection in l/f noise of SQUID magnetometers

It is shown that the variance on the SQUID power spectrum in the l/f low frequency region is well behaved, i.e., any small frequency band may be treated as white noise in standard power spectrum estimation theory. Specifically a calibration signal is examined at 0.017 Hz with an equivalent energy referred to the SQUID input coil of 1 times 10 to the -30th J and a digitally recorded and analyzed record of 140 hr duration obtained an optimum S/N better than 400. The results are in good agreement with theory. In addition no deviation from the l/f dependence of the noise energy spectrum is seen down to frequencies below 10 to the -5th Hz. A commercially available SQUID and electronics system were used.

Cabrera, B.↗
DOE OSTI2026

Data Driven Correlated Noise Simulation for the ICEBERG LArTPC

Accurate electronic-noise simulation is essential for low-energy physics in liquid-argon TPCs. More realistic noise modeling allows us to better tune reconstruction algorithms and more reliably assess and optimize signal-detection thresholds. We present a data-driven noise simulation framework developed for the ICEBERG test stand for DUNE that generates synthetic noise waveforms that reproduce both (i) the measured per-channel magnitude of the Fast Fourier Transform (FFT) and (ii) frequency-dependent channel-to-channel correlations observed in ICEBERG noise data. Using a dedicated noise-only dataset, we build a compact noise model containing per-channel FFT-magnitude targets together with a small set of band-wise cross-wire color matrices. White noise is generated in the frequency domain by drawing circular-symmetric complex Gaussian coefficients with random phases and scaling them to match the measured FFT-magnitude targets, and cross-wire correlations are subsequently imposed using the stored color matrices. The model and algorithm were integrated into the LArSoft + Wire-Cell Toolkit simulation chain and validated by comparing waveform structure, frequency-domain spectra, and band-limited correlation matrices from simulated noise and ICEBERG data. This approach can be extended to other LArTPC operating conditions.

Ghosh, Avik [Iowa State U.]↗
NASA NTRS2023

A Multi-Pixel Split-Window Approach to Sea Surface Temperature Retrieval from Thermal Imagers with Relatively High Radiometric Noise: Preliminary Studies

In the following decade(s), a set of satellite missions carrying thermal infrared (TIR) imagers with a relatively high noise equivalent differential temperature (NEdT) are expected, e.g., the high resolution TIR imagers flying on the future Thermal infraRed Imaging Satellite for High-resolution Natural resource Assessment (TRISHNA), Land Surface Temperature Monitoring (LSTM) and NASA-JPL/ASI Surface Biology and Geology Thermal (SBG) missions or the secondary payload on board the ESA Earth Explorer 10 Harmony. The instruments on board these missions are expected to be characterized by an NEdT of ⪆0.1 K. In order to reduce the impact of radiometric noise on the retrieved sea surface temperature (SST), this study investigates the possibility of applying a multi-pixel atmospheric correction based on the hypotheses that (i) the spatial variability scales of radiatively active atmospheric variables are, on average, larger than those of the SST and (ii) the effect of atmosphere is accounted for via the split window (SW) difference. Based on 32 Sentinel 3 SLSTR case studies selected in oceanic regions where SST features are mainly driven by meso to sub-mesoscale turbulence (e.g., corresponding to major western boundary currents), this study documents that the local spatial variability of the SW difference term on the scale of ≃3 × 3 km2 is comparable with the noise associated with the SW difference. Similarly, the power spectra of the SW term are shown to have, for small scales, the behavior of white noise spectra. On this basis, we suggest to average the SW term and to use it for the atmospheric correction procedure to reduce the impact of radiometric noise. In principle, this methodology can be applied on proper scales that can be dynamically defined for each pixel. The applicability of our findings to high-resolution TIR missions is discussed and an example of an application to ECOSTRESS data is reported.

sea surface temperature↗
NASA NTRS2002

Causes of Long-Term Drought in the United States Great Plains

The United States Great Plains (USGP) experienced a number of multi-year droughts during the last century, most notably the droughts of the 1930s and 1950s. This study examines the causes of such droughts using ensembles of long term (1930-1999) simulations carried out with the NASA Seasonal-to-Interannual Prediction Project (NSIPP-1) atmospheric general circulation model (AGCM) forced with observed sea surface temperatures (SSTs). The results show that the model produces long-term (multi-year) variations in the USGP precipitation that are similar to those observed. A correlative analysis suggests that the ensemble mean low frequency (time scales longer than about 6 years) rainfall variations in the USGP are linked to a pan-Pacific pattern of SST variability that is the leading empirical orthogonal function (EOF) in the low frequency SST data. The link between the SST and the Great Plains precipitation is confirmed in idealized AGCM simulations, in which the model is forced by the 2 polarities of the pan-Pacific SST pattern. The idealized simulations further show that it is primarily the tropical part of the SST anomalies that influence the USGP. As such, the USGP tend to have above normal precipitation when the tropical Pacific SSTs are above normal, while there is a tendency for drought when the tropical SSTs are cold. The upper tropospheric response to the pan-Pacific SST EOF shows a global-scale pattern with a strong wave response in the Pacific and a substantial zonally-symmetric component in which USGP pluvial (drought) conditions are associated with reduced (enhanced) heights throughout the extra-tropics. The potential predictability of rainfall in the USGP associated with SSTs is rather modest, with on average about 1/3 of the total low frequency rainfall variance forced by SST anomalies. Further idealized experiments with climatological SST, suggest that the remaining low frequency variance in the USGP precipitation is the result of interactions with soil moisture. In particular, simulations with soil moisture feedback show a six-fold increase in the variance in annual USGP precipitation compared with simulations in which the soil feedback is excluded. In addition to increasing variance, the interactions with the soil introduce year-to-year memory in the hydrological cycle that is consistent with a red noise process, in which the low frequencies in the deep soil are the result of integrating a net forcing (precipitation-evaporation-runoff) that is white noise on interannual time scales. As such, the role of low frequency SST variability is to introduce a bias to the net forcing on the soil moisture that drives the random process preferentially to either wet or dry conditions.

Schubert, Siegfried D.↗
DOE OSTI2026

Beyond Contrast Transfer: Spectral SNR as a Finite-Dose Metric for STEM Phase Retrieval

The contrast transfer function (CTF) is widely used to evaluate phase retrieval methods in scanning transmission electron microscopy (STEM), including center-of-mass imaging, parallax imaging, direct ptychography, and iterative ptychography. However, the CTF reflects only the maximum usable signal, neglecting the effects of finite electron fluence and the Poisson-limited nature of detection. As a result, it can significantly overestimate practical performance, especially in low-dose regimes. Here, we employ the spectral signal-to-noise ratio (SSNR), as a finite-dose statistical framework to evaluate the recoverable signal as a function of spatial frequency. Using numerical reconstructions of white-noise objects, we show that center-of-mass, parallax, and direct ptychography exhibit dose-independent SSNRs, with close-form analytic expressions. In contrast, iterative ptychography exhibits a surprising dose dependence: at low fluence, its SSNR converges to that of direct ptychography; at high fluence, it saturates at a value consistent with the maximum detective quantum efficiency predicted by recent quantum Fisher information bounds. The results highlight the limitations of CTF-based evaluation and motivate SSNR as a more accurate, finite-dose metric for assessing STEM phase retrieval methods.

STEM phase retrieval↗
NASA NTRS1972

Input noise approximation in tracker modeling

The validity of approximating random Gaussian distributed inputs used in human response modeling by sums of discrete sine waves is studied. An ideal rectangular power density spectrum is simulated using both filtered Gaussian white noise and sums-of-discrete sine waves with three different input cutoff frequencies in the same compensatory tracking task. Resulting normalized tracking error and quality operator observations are used to investigate apparent discrepancies in human operator characteristics. Results show that discrete and continuous input tracking data compare favorable when the power in the crossover region is taken into account.

Torrey, P. F.↗
NASA NTRS1985

Shuttle electrical environment

Part of an AFGL payload flown on the STS-4 mission consisted of experiments to measure in-situ electric fields, electron densities, and vehicle charging. During this flight some 11 hours of data were acquired ranging from 5 minute snapshots up to continuous half-orbits. These experiments are described and results presented for such vehicle induced events as a main engine burn, thruster firings and water dumps in addition to undisturbed periods. The main characteristic of all the vehicle induced events is shown to be an enhancement in the low frequency noise (less than 2 kHz), in both the electrostatic and electron irregularity (delta N/N) spectra. The non-event results indicate that the electrostatic broadband emissions show a white noise characteristic in the low frequency range up to 2 kHz at an amplitude of 10 db above the shuttle design specification limit, falling below that limit above 10 kHz. The vehicle potential remained within the range of -3 to +1 volt throughout the flight which exhibits normal behavior for a satellite in a low equatorial orbit.

Smiddy, M.↗
NASA NTRS1975

Development of a Low-Noise High Common-Mode-Rejection Instrumentation Amplifier

Several previously used instrumentation amplifier circuits were examined to find limitations and possibilities for improvement. One general configuration is analyzed in detail, and methods for improvement are enumerated. An improved amplifier circuit is described and analyzed with respect to common mode rejection and noise. Experimental data are presented showing good agreement between calculated and measured common mode rejection ratio and equivalent noise resistance. The amplifier is shown to be capable of common mode rejection in excess of 140 db for a trimmed circuit at frequencies below 100 Hz and equivalent white noise below 3.0 nv/square root of Hz above 1000 Hz.

Rush, Kenneth↗
NASA NTRS1984

Uniform apparent contrast noise: A picture of the noise of the visual contrast detection system

A picture which is a sample of random contrast noise is generated. The noise amplitude spectrum in each region of the picture is inversely proportional to spatial frequency contrast sensitivity for that region, assuming the observer fixates the center of the picture and is the appropriate distance from it. In this case, the picture appears to have approximately the same contrast everywhere. To the extent that contrast detection thresholds are determined by visual system noise, this picture can be regarded as a picture of the noise of that system. There is evidence that, at different eccentricities, contrast sensitivity functions differ only by a magnification factor. The picture was generated by filtering a sample of white noise with a filter whose frequency response is inversely proportional to foveal contrast sensitivity. It was then stretched by a space-varying magnification function. The picture summmarizes a noise linear model of detection and discrimination of contrast signals by referring the model noise to the input picture domain.

Ahumada, A. J., Jr.↗
NASA NTRS1994

Control of maglev vehicles with aerodynamic and guideway disturbances

A modeling, analysis, and control design methodology is presented for maglev vehicle ride quality performance improvement as measured by the Pepler Index. Ride quality enhancement is considered through active control of secondary suspension elements and active aerodynamic surfaces mounted on the train. To analyze and quantify the benefits of active control, the authors have developed a five degree-of-freedom lumped parameter model suitable for describing a large class of maglev vehicles, including both channel and box-beam guideway configurations. Elements of this modeling capability have been recently employed in studies sponsored by the U.S. Department of Transportation (DOT). A perturbation analysis about an operating point, defined by vehicle and average crosswind velocities, yields a suitable linearized state space model for multivariable control system analysis and synthesis. Neglecting passenger compartment noise, the ride quality as quantified by the Pepler Index is readily computed from the system states. A statistical analysis is performed by modeling the crosswind disturbances and guideway variations as filtered white noise, whereby the Pepler Index is established in closed form through the solution to a matrix Lyapunov equation. Data is presented which indicates the anticipated ride quality achieved through various closed-loop control arrangements.

Flueckiger, Karl↗
NASA NTRS1973

Transient characteristics of simple systems to modulated random noise.

Discussed are the mean-square response exceedance characteristics of a single-tuned system to amplitude modulated noise. The results bear on the accuracy of spectral estimates of nonstationary data, and subsequently, relate directly to the design, analysis, and testing of structural systems in environments as gusts, earthquakes, and ignition transients. For noise correlated as an exponentially damped cosine, the nonstationary response may exceed its stationary value by a factor in excess of two. A time-varying shaping filter explanation is offered for this behavior. For white noise, such exceedances do not occur.

Barnoski, R. L.↗
NASA NTRS1986

A fully redundant double difference algorithm for obtaining minimum variance estimates from GPS observations

In double differencing a regression system obtained from concurrent Global Positioning System (GPS) observation sequences, one either undersamples the system to avoid introducing colored measurement statistics, or one fully samples the system incurring the resulting non-diagonal covariance matrix for the differenced measurement errors. A suboptimal estimation result will be obtained in the undersampling case and will also be obtained in the fully sampled case unless the color noise statistics are taken into account. The latter approach requires a least squares weighting matrix derived from inversion of a non-diagonal covariance matrix for the differenced measurement errors instead of inversion of the customary diagonal one associated with white noise processes. Presented is the so-called fully redundant double differencing algorithm for generating a weighted double differenced regression system that yields equivalent estimation results, but features for certain cases a diagonal weighting matrix even though the differenced measurement error statistics are highly colored.

Melbourne, William G.↗
NASA NTRS1997

The Accuracy of Saccadic and Perceptual Decisions in Visual Search

Saccadic eye movements during search for a target embedded in noise are suboptimally guided by information about target location. Our goal is to compare the spatial information used to guide the saccades with that used for the perceptual decision. Three observers were asked to determine the location of a bright disk (diameter = 21 min) in white noise (signal-to-noise ratio = 4.2) from among 10 possible locations evenly spaced at 5.9 deg eccentricity. In the first of four conditions, observers used natural eye movements. In the three remaining conditions, observers fixated a central cross at all times. The fixation conditions consisted of three different presentation times (100, 200, 300 msec), each followed by a mask. Eye-position data were collected, with a resolution of (approximately) 0.2 deg. In the natural viewing condition, we measured. the accuracy with respect to the target and the latency of the first saccade. In the fixation conditions, we discarded trials in which observers broke fixation. Perceptual performance was computed for all conditions. Averaged across observers, the first saccade was correct (closest to the target location) for 56 +/- (SD) % of trials (chance = 10 %) and occurred after a latency of 313 +/- 56 msec. Perceptual performance averaged 53 +/- 4, 63 +/- 4, 65 +/- 2 % correct at 100, 200, and 300 msec, respectively. For the signal-to-noise ratio used, at the time of initiation of the first saccade, there is little difference between the amount of information about target location available to the perceptual and saccadic systems.

Eckstein, Miguel P.↗
NASA NTRS1996

Noise and Dynamical Pattern Selection

In pattern-forming systems, such as Rayleigh-Benard convection or directional solidification, a large number of linearly stable, patterned steady states exist when the basic, simple steady state is unstable. Which of these steady states will be realized in a given experiment appears to depend on unobservable details of the system's initial conditions. We show, however, that weak, Gaussian white noise drives such a system toward a preferred wave number which depends only on the system parameters and is independent of initial conditions. We give a prescription for calculating this wave number, analytically near the onset of instability and numerically otherwise.

Kurtze, Douglas A.↗
NASA NTRS1971

Bayesian recursive image estimation.

A procedure for recursively estimating images that are characterized statistically by the mean and correlation functions associated with the random process representing the brightness level is proposed for the case where the images are corrupted by additive noise. First, a dynamic model is developed with a response characteristic which matches that of the scanner output (the input of the estimator is the output of a horizontal line scanner) in a statistical sense. Such models have the form of an ordinary differential or difference equation with white noise input. An insignificant approximation is introduced by using a constant-coefficient model. The appropriate model is a vector valued difference equation with the solution representing a vector Markov process. The next step is to obtain the minimum mean square estimate of the image by using a Kalman filter. Since the image estimation is an interpolation problem, two successive runs over the observation are performed in opposite directions and the resultant estimates are averaged. Examples are included for illustration.

Nahi, N. E.↗
NASA NTRS1981

A stochastic-dynamical approach to the study of the natural variability of the climate

A method, suggested by Leith (1975), which employed stochastic-dynamic forecasts obtained from a general circulation model in such a way as to satisfy the definition of climatic noise, was used to validate assumptions accounting for the effects of external influences in estimating the climatic noise. Two assumptions were investigated: (1) that the weather fluctuations can be represented as a Markov process, and (2) that changing external conditions do not influence the atmosphere's statistical properties on short time scales. The general circulation model's simulation of the daily weather fluctuations was generated by performing integrations with prescribed climatological boundary conditions for random initial atmospheric states, with resulting dynamical forecasts providing an ensemble of simulated data for the autoregressive modeling of weather fluctuations. To estimate the climatic noise from the observational data (consisting of hourly values of sea level pressure and surface temperature at 54 U.S. stations for the month of January for the years 1949-1975) use of the short time-scale assumption is made. The simulated and observed data were found not to be consistent with either white noise or a Markov process of weather fluctuations. Good agreement was found between the results of the hypothetical testing of the simulated and the observed surface temperatures; and only partial support was found for the short time-scale assumption, i.e., for sea level pressure.

Straus, D. M.↗