Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Passive Orbital Disconnect Strut (PODS 3), structural and thermal test program

A test program is undertaken to verify that the lifetime of a shuttle launchable dewar can be increased by using passive orbital disconnect struts (PODS). A detailed design is performed on the cold end (PODS-III) portion of the strut. Structural analysis of the thin-wall fiberglass tube allows selection of the optimum winding angle and tube dimensions. Structural tests on the thin-wall fiberglass tube measure both the tension and compression modulus at ambient and LN2 temperatures, the radial deflection versus side load, and the ultimate compression strength of the tube at LN2 temperature. The thermal expansion of the fiberglass tube plus Invar is also measured down to 78 K. The axial gap at the wedge portion of the stem is set based on these data. The PODS-III test article parts are fabricated and assembled using a detailed assembly procedure. The thermal conductants in the orbital configuration was measured for body temperatures between 5 and 40 K. This temperature range covers the predicted ground hold and orbit temperatures for vapor-cooled supports. The test results are then compared with heat leak values predicted before the test began. Side load, axial compression load, and tension load tests conclude the test program.

Parmley, R. T.↗
NASA NTRS1986

Toggle Hinge for Deployable Struts

Toggle hinge allows deployable structures erected without end play encountered in conventional hinged structural members. New hinge ensures rigidity in portable bridges, masts, towers, platforms, and other deployable (and retractable) structures. Positioned halfway along length of folding strut, hinge allows halves of strut to pivot 180 degrees about center.

Barbour, R. T.↗
NASA NTRS1984

Passive orbital disconnect strut

The design and test results with a third generation passive orbital disconnect strut (PODS) for space-based cryogenic He dewars are presented. Three pairs of PODS struts support a tank and change lengths in response to gas and temperature changes. A thin wall fiberglass tube is used on the cold disconnect end, which can be operated on the ground or in space. Tests were performed to characterize heat flows across the cold end to a liquid He sink and subsequent vacuum pressure within the He tank. Heat transfer was lower than predicted, suggesting that longer dewar in-orbit lifetimes can be expected with the new PODS.

Parmley, R. T.↗
NASA NTRS1992

Fiber Jackets For Vibration-Damping Struts

Jacket of braided fibers fastens to structural joints at ends of strut. Carries excessive tensile loads, partly bypassing strut. Friction between braided fibers gives rise to hysteresis in stress-versus-strain behavior of jacket. Hysteresis enhances absorption of large vibrations.

Dolgin, Benjamin P.↗
NASA NTRS1993

Modified Composite Struts Would Damp Vibrations

Composite-material (fiber/matrix laminate) struts damping longitudinal vibrations fabricated more easily in proposed new design. Prior design described in "Composite Struts Would Damp Vibrations" (NPO-17914). New design similar except pattern of fibers includes rounded bends (instead of sharp bends) in fibers.

Chen, Gun-Shing↗
NASA NTRS1992

Active strut placement using integer programming for the CSI Revolutionary Model

A method for determining the most effective locations for active struts on large space structures is developed and tested on the NASA CSI Evolutionary Model. Depending on the choice of weighting factors, the method can be used to maximize the maximum modal damping ratio or decay rate, or to maximize a mission-oriented measure of performance. Placement of 8, 16, and 32 active struts out of 1507 candidate truss elements is demonstrated. Preliminary estimates of damping enhancement are reported pending refined structural models and dynamic test results. The method can handle complicated FEM models wih a large number of truss elements and many target modes. It can treat each mode equally or it can emphasize the importance of selected modes. The method can eliminate some combinations of actuator locations based on topological constraints.

Padula, Sharon L.↗
NASA NTRS1951

Data Presentation of Force Characteristics of Several Engine-strut-body Configurations at Mach Numbers of 1.8 and 2.0 / Robert T. Madden and Emil J. Kremzier

Investigation to determine lift, drag, and pitching-moment characteristics of several engine-strut-body combinations was conducted over range of angles of attack from 0 degrees to 10 degrees at Mach numbers of 1.8 and 2.0. The average Reynolds number based on body length was 28x106. Data are presented without analysis and indicate decreases in minimum drag and lift curve slope with decreasing in minimum drag and lift curve slope with decreasing strut length. Decreases in minimum drag also noted with rear-ward movement of engines.

PROTUBERANCES - BODIES↗
NASA NTRS1930

Aerodynamic theory and test of strut forms. Part I

This report presents the first part of a two part study made under this title. In this part the symmetrical inviscid flow about an empirical strut of high service merit is found by both the Rankine and the Joukowsky methods. The results can be made to agree as closely as wished. Theoretical stream surfaces as well as surfaces of constant speed and pressure in the fluid about the strut are found. The surface pressure computed from the two theories agrees well with the measured pressure on the fore part of the model but not so well on the after part. From the theoretical flow speed the surface friction is computed by an empirical formula. The drag integrated from the friction and measured pressure closely equals the whole measured drag. As the pressure drag and the whole drag are accurately determined, the friction formula also appears trustworthy for such fair shapes. (author)

Smith, R H↗
NASA NTRS1932

Dynamic testing of airplane shock-absorbing struts

Measurement of perpendicular impacts of a landing gear with different shock-absorbing struts against the drum testing stand. Tests were made with pneumatic shock absorbers having various degrees of damping, liquid shock absorbers, steel-spring shock absorbers and rigid struts. Falling tests and rolling tests. Maximum impact and gradual reduction of the impacts in number and time in the falling tests. Maximum impact and number of weaker impacts in rolling tests.

Langer, P↗
NASA NTRS1960

Landing-Impact Characteristics of Load-Alleviating Struts on a Model of a Winged Space Vehicle

A brief experimental investigation was made of the landing-impact characteristics of a 1/9-scale dynamic model of a winged space vehicle. The landing tests were made by catapulting a free model onto a hard; surface runway and onto water. The model had a conical fuselage and a flat - plate wing with a basic delta planform and 75 deg sweepback of the leading edge. The use of yielding-metal shock absorbers and various landing-gear arrangements was investigated during landing impact. The basic landing gear consisted of a dual rubber-tired nose wheel and twin main skids aft of the center of gravity near the wing tips. landing motion and acceleration data were obtained over a range of landing attitudes, gross weights, and initial sinking speeds. Brief tests were made with an alternate nose-wheel location. An all-skid configuration also was briefly evaluated for hard-surface and water landings. The landing gear employing yielding struts for impact-energy absorption during hard-surface landings resulted in accelerations of approximately 5 1/2 g near the nose gear over a range of landing parameters. Replacing the nose wheel and tire with a skid did not significantly change the accelerations. Landings in smooth water with rigid struts and adequate planing area at the nose skid resulted in a maximum landing acceleration of approximately 4g.

Blanchard, Ulysse J.↗
NASA NTRS1953

An Exploratory Investigation of Some Types of Aeroelastic Instability of Open and Closed Bodies of Revolution Mounted on Slender Struts

Aeroelastic instability phenomena of isolated open and closed rigid bodies of revolution free to move under elastic restraint have been investigated experimentally at low speeds by means of models suspended at zero angles of attack and yaw on slender flexible struts from a wind tunnel ceiling. Three types of instability were observed - flutter similar to classical bending-torsion flutter, divergence, and an uncoupled oscillatory instability which consists in nonviolent continuous or intermittent small-amplitude oscillations involving only angular deformations. The speeds at which this oscillatory instability starts were found to be as low as about one-third of the speed at flutter or divergence and to depend on the shape of the body, particularly that of the afterbody, and on the relative location of the elastic axis. An attempt has been made to calculate the airspeeds and, in the case of the oscillatory phenomena, the frequencies at which these instabilities occur by using slender-body theory for the aerodynamic forces on the bodies and neglecting the aerodynamic forces on the struts. However, the agreement between the speeds and frequencies calculated in this manner and those actually observed has been found to be generally unsatisfactory; with the exception of the frequencies of the uncoupled oscillations which could be predicted with fair accuracy. The nature of the observed phenomena and of the forces on bodies of revolution suggests that a significant improvement in the accuracy of analytical predictions of these aeroelastic instabilities can be had only by taking into account the effects of boundary-layer separation on the aerodynamic forces.

Clevenson, S. A.↗
NASA NTRS1954

Experimental Permeability Measurements on a Strut-Supported Transpiration-Cooled Turbine Blade with Stainless-Steel Shell made by the Federal-Mogul Corporation under Bureau of Aeronautics Contract N0as 51613-C

A turbine blade with a porous stainless-steel shell sintered to a supporting steel strut has been fabricated for tests at the NACA by Federal-Mogul Corporation under contract from the Bureau of Aeronautics, Department of the Navy. The apparent permeability of this blade, on the average, more nearly approaches the values specified by the NAGA than did two strut-supported bronze blades in a previous investigation. Random variations of permeability in the present blade are substantialy greater than those of the bronze blades, but projected improvements in certain phases of the fabrication process are expected to reduce these variations.

Richards, Hadley T.↗
NASA NTRS2009

Design and Manufacture of Structurally Efficient Tapered Struts

Composite materials offer the potential of weight savings for numerous spacecraft and aircraft applications. A composite strut is just one integral part of the node-to-node system and the optimization of the shut and node assembly is needed to take full advantage of the benefit of composites materials. Lockheed Martin designed and manufactured a very light weight one piece composite tapered strut that is fully representative of a full scale flight article. In addition, the team designed and built a prototype of the node and end fitting system that will effectively integrate and work with the full scale flight articles.

Brewster, Jebediah W.↗
NASA NTRS2012

The Transport of Mass, Energy, and Entropy in Cryogenic Support Struts for Engineering Design

Engineers working to understand and reduce cryogenic boil-off must solve a. variety of transport problems. An important class of nonlinear problems involves the thermal and mechanical design of cryogenic struts. These classic problems are scattered about the literature and typically require too many resources to obtain. So, to save time for practicing engineers, the author presents this essay. Herein, a variety of new, old, and revisited analytical and finite difference solutions of the thermal problem are covered in this essay, along with commentary on approach and assumptions, This includes a few thermal radiation and conduction combined mode solution with a discussion on insulation, optimum emissivity, and geometrical phenomenon. Solutions to cooling and heat interception problems are also presented, including a discussion of the entropy generation. And the literature on the combined mechanical and thermal design of cryogenic support struts is reviewed with an introduction to the associated numerical methods.

Elchert, J. P.↗
NASA NTRS2012

The Transport of Mass, Energy, and Entropy in Cryogenic Support Struts for Engineering Design

Engineers working to understand and reduce cryogenic boil-off must solve a variety of transport problems. An important class of nonlinear problems involves the thermal and mechanical design of cryogenic struts. These classic problems are scattered about the literature and typically require too many resources to obtain. So, to save time for practicing engineers, the author presents this essay. Herein, a variety of new, old, and revisited analytical and finite difference solutions of the thermal problem are covered in this essay, along with commentary on approach and assumptions. This includes a few thermal radiation and conduction combined mode solutions with a discussion on insulation, optimum emissivity, and geometrical phenomenon. Solutions to cooling and heat interception problems are also presented, including a discussion of the entropy generation. The literature on the combined mechanical and thermal design of cryogenic support struts is reviewed with an introduction to the associated numerical methods.

Elchert, J. P.↗
NASA NTRS2019

Aero-Structural Modeling of the Truss-Braced Wing Aircraft Using Potential Method with Correction Methods for Transonic Viscous Flow and Wing-Strut Interference Aerodynamics

This paper describes an aero-structural modeling method for the Transonic Truss-Braced Wing (TTBW) aircraft using VSPAERO. A vortex-lattice model of the TTBW aircraft is developed, and a transonic and viscous flow correction method is implemented in the VSPAERO models to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. Also, a structural dynamic finite-element model of the TTBW aircraft is developed. This finite-element model includes the geometric nonlinear effect due to the tension in the struts which cause a deflection dependent nonlinear stiffness. The VSPAERO models are coupled to the finite-element model to provide a rapid capability for aero-structural modeling and flutter analysis. A flight-optimized jig twist model is being developed and will be applied for the purpose of generating a full flight dynamic model of the TTBW aircraft.

Fugate, Jason↗