Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Irradiation defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Radiation Damage Mitigation in FeCrAl Alloy at Sub-Recrystallization Temperatures

Traditional defect recovery methods rely on high-temperature annealing, often exceeding 750 °C for FeCrAl. In this study, we introduce electron wind force (EWF)-assisted annealing as an alternative approach to mitigate irradiation-induced defects at significantly lower temperatures. FeCrAl samples irradiated with 5 MeV Zr 2+ ions at a dose of 10 14 cm −2 were annealed using EWF at 250 °C for 60 s. We demonstrate a remarkable transformation in the irradiated microstructure, where significant increases in kernel average misorientation (KAM) and low-angle grain boundaries (LAGBs) typically indicate heightened defect density; the use of EWF annealing reversed these effects. X-ray diffraction (XRD) confirmed these findings, showing substantial reductions in full width at half maximum (FWHM) values and a realignment of peak positions toward their original states, indicative of stress and defect recovery. To compare the effectiveness of EWF, we also conducted traditional thermal annealing at 250 °C for 7 h, which proved less effective in defect recovery as evidenced by less pronounced improvements in XRD FWHM values.

FeCrAl alloys↗
DOE OSTI2024

Mechanisms of ion irradiation induced ordering in amorphous TiO 2 nanotubes: Effects of ion mass and energy

Here, amorphous TiO 2 nanotubes were irradiated in-situ in a transmission electron microscope (TEM) with Kr + ions at energies of 46 keV, 150 keV, and 1 MeV and with 46 keV Xe + ions, to investigate the structural and morphological evolution of the nanotubes under irradiation. At all irradiation conditions, amorphous TiO 2 nanotubes exhibited significant morphological instability, and tended to undergo volumetric swelling with increasing ion counts, often until collapse of the original nanotube structure. Molecular dynamics (MD) simulations confirmed that irradiation-induced defects can explain the observed swelling. Structurally, nanotubes remain amorphous following all Kr + irradiation conditions, but irradiation with 46 keV Xe + leads to the formation of anatase nanocrystallites. Importantly, through systematically varying ion energy and ion species, we try to elucidate the influence of nuclear and electronic stopping power on ion irradiation induced changes. By contextualizing these results within the existing literature, we propose that the observed changes in TiO 2 nanotube morphology and structure could be due to a competition between two mechanisms: (1) disorder-induced swelling and (2) irradiation-induced amorphous-to-crystalline transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Helium bubble formation in nickel under in-situ krypton and helium ions dual-beam irradiation

Helium has profound effects on the microstructure and mechanical property of materials used in nuclear power systems. Here to understand the interaction between helium and irradiation-induced defects and its effect on bubble formation, single-beam and dual-beam irradiations on nickel were performed with 16 keV helium ions and 1 MeV krypton ions under in-situ TEM observation. For 1 MeV krypton single-beam irradiation, voids were observed at 600ºC but not at 500ºC and 700ºC. For helium single-beam irradiation at 500ºC, helium moved freely and formed bubble-loop complexes. For dual-beam irradiation at 500ºC, helium was trapped by vacancies and formed bubbles homogeneously. The structure of dislocation loops was also affected by the presence of helium. For krypton single-beam irradiation at 500ºC, the microstructure was {100} periodic wall of faulted and perfect dislocation loops. For dual-beam irradiation at 500ºC, periodic wall was not observed, and dislocation loops were predominantly perfect. For single-beam helium at 500ºC, dislocation loops were produced by athermal process of SIAs ejection or loop punching mechanisms. The interplay between helium and vacancies played an important role on the evolution of helium bubbles and defect microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Multiphysics FISPACT-II and TENDL-2019 simulation: neutron-induced damage metrics

Nuclear interactions can be the source of atomic displacement, irradiation-induced defects and transmutation in structural materials. Such quantities are derived from, or can be correlated to, nuclear kinematic simulations of primary atomic energy distributions spectra and the quantification of the numbers of secondary defects produced per primary as a function of the available recoils, residual and emitted, energies. Recoil kinematics of neutral, residual, gas, proton, alpha particle emissions are now more rigorously treated based on recent, complete and enhanced nuclear data parsed in state-of-the-art processing tools. Defect production metrics are the starting point in the complex problem of correlating and simulating the behaviour of materials under irradiation, as experimental information is rare or scattered. Detailed, segregated primary knock-on-atom metrics are now becoming available as the starting point of further simulation processes of isolated and clustered defects in material lattices. This allows more materials, lattices, neutron incident energy ranges, and irradiation conditions to be explored with sufficient data to adequately cover both standard and novel applications and materials: the broader reactor applications landscape. The damage metrics of of materials are systematically explored under typical but different reactor's type environment. The inventory code FISPACT-II combined with the enhanced nuclear data forms of the TENDL-2019 libraries allow one to not only calculate dpa from mostly scattering events but to also properly predict gas production, nuclear heating and transmutation under the same conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Application of Weak-Beam Dark-Field STEM for Dislocation Loop Analysis

Nanoscale dislocation loops formed by irradiation can significantly contribute to both irradiation hardening and embrittlement of materials when subjected to extreme nuclear reactor environments. Here, this study explores the application of weak-beam dark-field (WBDF) scanning transmission electron microscopy (STEM) methods for quantitative irradiation-induced defect analysis in crystalline materials, with a specific focus on dislocation loop imaging and analysis. A high-purity Fe-5 wt% Cr model alloy was irradiated with 8 MeV Fe 2+ ions at 450°C to a fluence of 8.8 × 10 19 m -2 , inducing dislocation loops for analysis. While transmission electron microscopy (TEM) has traditionally been the primary tool for dislocation imaging, recent advancements in STEM technology have reignited interest in using STEM for defect imaging. This study introduces and compares three WBDF STEM methods, demonstrating their effectiveness in suppressing background contrasts, isolating defect information for dislocation loop type classification, providing finer dislocation line images for small loop analysis, and presenting inside–outside contrast for identifying loop nature. Experimental findings indicate that WBDF STEM methods surpass traditional TEM approaches, yielding clearer and more detailed images of dislocation loops. The study concludes by discussing the potential applications of WBDF STEM techniques in defect analysis, emphasizing their adaptability across various material systems beyond nuclear materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Defect Generation and Evolution in Irradiated Epitaxial Films and Heterostructures of Fe 3 O 4 and Cr 2 O 3

Abstract The functionality of nuclear structural materials, sensors, and microelectronics in harsh environments such as radiation relies on understanding defect generation and evolution processes in oxide layers. The initial radiation response of epitaxial thin films of Fe 3 O 4 (111), Cr 2 O 3 (0001), and Fe 3 O 4 (111)/Cr 2 O 3 (0001) heterostructures deposited on Al 2 O 3 (0001) by oxygen‐assisted molecular beam epitaxy and irradiated with 200 keV He + is characterized. X‐ray diffraction and X‐ray absorption near edge spectroscopy showed that the Cr 2 O 3 layers underwent significant lattice expansion and disordering under irradiation, whereas the Fe 3 O 4 layers do not exhibit noticeable changes. In contrast, positron annihilation spectroscopy revealed an evolution of cation vacancy point defects in the Fe 3 O 4 layers into larger vacancy clusters with increasing irradiation, while the cation vacancies in Cr 2 O 3 remained primarily as single vacancies and small clusters. The results suggest that the Fe 3 O 4 lattice can utilize the free volume of the larger vacancy clusters to relax but the small vacancies in the Cr 2 O 3 lattice do not facilitate relaxation. Comparing defect concentrations in the single layer films versus the heterostructure suggests that point defects may cross the interface from Fe 3 O 4 into Cr 2 O 3 . Together, these results enhance the understanding of the initial defect evolution mechanisms in oxide layers in harsh irradiation environments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Comparison of Radiation-Induced and High-Field Electrically Stress-Induced Interface Defects in Si/SiO 2 MOSFETs via Electrically Detected Magnetic Resonance

Here, we utilize electrically detected magnetic resonance (EDMR) measurements to compare high-field stressed, and gamma irradiated Si/SiO 2 metal–oxide–silicon (MOS) structures. We utilize spin-dependent recombination (SDR) EDMR detected using the Fitzgerald and Grove dc I-V approach to compare the effects of high-field electrical stressing and gamma irradiation on defect formation at and near the Si/SiO 2 interface. As anticipated, both greatly increase the concentration of P b centers (silicon dangling bonds at the interface) densities. The irradiation also generated a significant increase in the dc I-V EDMR response of E' centers (oxygen vacancies in the SiO 2 films), whereas the generation of an E' EDMR response in high-field stressing is much weaker than in the gamma irradiation case. These results likely suggest a difference in their physical distribution resulting from radiation damage and high electric field stressing.

42 ENGINEERING↗
NASA NTRS1986

Cell performance and defect behavior in proton-irradiated lithium-counterdoped n(+)p silicon solar cells

Lithium-counterdoped n(+)p silicon solar cells were irradiated by 10-MeV protons, and their performance was determined as a function of fluence. It was found that the cell with the highest lithium concentration exhibited the higher radiation resistance. Deep-level transient spectroscopy studies of deep-level defects were used to identify two lithium-related defects. Defect energy levels obtained after the present 10-MeV irradiations were found to be markedly different than those observed after previous 1-MeV electron irradiations. However, the present DLTS data are consistent with previous suggestion by Weinberg et al. (1984) of a lithium-oxygen interaction which tends to inhibit formation of an interstitial boron-oxygen defect.

Weinberg, I.↗
DOE OSTI2021

Examining deformation localization of irradiated tungsten under uniaxial compression with crystal plasticity

In this work, the deformation behavior of irradiated tungsten at elevated service temperatures is examined using mechanism-based crystal plasticity finite element framework by considering multiple mechanisms, including thermal softening and irradiation hardening. The previously developed mechanism-based crystal plasticity model is first utilized to assess the yield stress of unirradiated and irradiated tungsten upon low-temperature irradiation. Additionally, the engineering stress-strain response under uniaxial compression is then predicted by considering the effect of irradiation-induced defect clusters on the motion of deformation-induced dislocations, and the predicted results agree well with the experimental measurements. More importantly, the formation and evolution of plastic strain localization zones in the form of shear bands are qualitatively captured, and the maximal principal strain distribution is quantitatively linked to the dose of irradiation damage. Finally, the deformation-induced shear band as a result of plastic instability in the compressed tungsten specimen is discussed.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Effects of low temperature periodic annealing on the deep-level defects in 200 keV proton irradiated AlGaAs-GaAs solar cells

The GaAs solar cell has shown good potential for space applications. However, degradation in performance occurred when the cells were irradiated by high energy electrons and protons in the space environment. The considered investigation is concerned with the effect of periodic thermal annealing on the deep-level defects induced by the 200 keV protons in the AlGaAs-GaAs solar cells. Protons at a fluence of 10 to the 11th P/sq cm were used in the irradiation cycle, while annealing temperatures of 200 C (for 24 hours), 300 C (six hours), and 400 C (six hours) were employed. The most likely candidate for the E(c) -0.71 eV electron trap observed in the 200 keV proton irradiated samples may be due to GaAs antisite, while the observed E(v) +0.18 eV hole trap has been attributed to the gallium vacancy related defect. The obtained results show that periodic annealing in the considered case does not offer any advantages over the one time annealing process.

Li, S. S.↗
DOE OSTI2024

Computer vision models and advanced TEM imaging for microstructures of irradiated AM316 stainless steels

Advancements were made in automating microscopy-based material characterization, particularly in studying irradiation effects on additively manufactured (AM) materials using machine learning (ML) and computer vision (CV). These automation efforts address the challenges of analyzing complex microstructures, accelerating the detection of irradiation-induced defects. Two CV models were developed at Argonne National Laboratory (ANL) to enhance transmission electron microscopy (TEM) analysis of irradiated AM 316 stainless steel. The first model focused on the detection of irradiation-induced dislocation loops, which contribute to material hardening and embrittlement. These loops, categorized as faulted or perfect, were automatically detected and classified using a Mask R-CNN model trained on TEM images from both in-situ and ex-situ ion irradiation experiments. The model achieved high accuracy, with precision, recall, and F1 scores of 0.839, 0.734, and 0.776, respectively, demonstrating its effectiveness in analyzing dislocation loops in irradiated AM materials. The second CV model was developed to analyze the size and wall thickness of dislocation cells in laser powder bed fusion (LPBF) 316 stainless steel. Using a U-Net++ architecture with EfficientNet as the encoder, the model was trained on TEM images to segment and measure cell size and wall thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2025

ATOMIC AND MICROSTRUCTURAL ORIGINS OF STORED ENERGY RELEASE IN NEUTRON-IRRADIATED SILICON CARBIDE

Here, we employ a combination of advanced synchrotron-based scattering characterization techniques to understand and unravel the atomic origins of the colossal stored energy release in neutron irradiated silicon carbide. The quantification of the neutron irradiation-induced defects, and their impact on the structureproperty relationship is important for the design and safe operation of advanced fission and fusion reactors. Our experimental results show that the atomic structure in the as irradiated samples is significantly perturbed due to a large fraction of vacancy and interstitial type defects that lead to complex microstructures and additional components in the x-ray diffraction and pair distribution function results. We directly correlate the stored energy release to the recovery of the sub-lattices, with pair distribution function analysis highlighting that the carbon interstitial and vacancy-type defects contribute to stored energy more than those of silicon. We find these results to be striking and believe our discoveries to be timely and noteworthy given the technological importance of silicon carbide to the nuclear fission and fusion communities.

Sprouster, D.J.↗
DOE OSTI2023

Thermal and Radiation Stability in Nanocrystalline Cu

Nanocrystalline metals have presented intriguing possibilities for use in radiation environments due to their high grain boundary volume, serving as enhanced irradiation-induced defect sinks. Their promise has been lessened due to the propensity for nanocrystalline metals to suffer deleterious grain growth from combinations of irradiation and/or elevated homologous temperature. While approaches for stabilizing such materials against grain growth are the subject of current research, there is still a lack of central knowledge on the irradiation–grain boundary interactions in pure metals despite many studies on the same. Due to the breadth of available reports, we have critically reviewed studies on irradiation and thermal stability in pure, nanocrystalline copper (Cu) as a model FCC material, and on a few dilute Cu-based alloys. Our study has shown that, viewed collectively, there are large differences in interpretation of irradiation–grain boundary interactions, primarily due to a wide range of irradiation environments and variability in materials processing. We discuss the sources of these differences and analyses herein. Then, with the goal of gaining a more overarching mechanistic understanding of grain size stability in pure materials under irradiation, we provide several key recommendations for making meaningful evaluations across materials with different processing and under variable irradiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Tailoring the Angular Mismatch in MoS 2 Homobilayers through Deformation Fields

Ultrathin MoS 2 has shown remarkable characteristics at the atomic scale with an immutable disorder to weak external stimuli. Ion beam modification unlocks the potential to selectively tune the size, concentration, and morphology of defects produced at the site of impact in 2D materials. Combining experiments, first-principles calculations, atomistic simulations, and transfer learning, it is shown that irradiation-induced defects can induce a rotation-dependent moiré pattern in vertically stacked homobilayers of MoS 2 by deforming the atomically thin material and exciting surface acoustic waves (SAWs). Furthermore, the direct correlation between stress and lattice disorder by probing the intrinsic defects and atomic environments are demonstrated. The method introduced in this paper sheds light on how engineering defects in the lattice can be used to tailor the angular mismatch in van der Waals (vdW) solids.

2D materials↗
DOE OSTI2024

Understanding the effect of crystal anisotropy on grain growth, texturing and transport via the orthorhombic ?-U system [Slides]

The alpha phase of uranium exhibits the orthorhombic crystal structure, resulting in significant physical property anisotropy. These complex properties make the material challenging to work with in engineering settings but provide a rich arena to investigate the fundamental, multi-scale effects of anisotropy on physical behaviors such as grain growth and microstructure evolution under irradiation. We apply molecular dynamics and phase field modeling to study mass transport and grain growth in alpha-uranium. We characterize the mobilities of crystalline defects and the interfacial energy, and We find that the grain boundary energy is highly variable depending on the interface structure and that the relative rates of defect transport change with temperature. We also find that anisotropic thermal expansion has a significant impact on grain growth kinetics and texture development. Our results are used to explain experimental observations and to provide a basis for further hypotheses into the complex physical behavior of alpha-uranium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗