Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Antennas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 109 records · Page 6
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Notes on Tapered Active Array Antenna Performance

Modern Active Electronically Steerable Array (AESA) antennas offer substantial control over transmit and receive antenna beam forming, including via elemental weighting to achieve a desired tapered aperture. However, these tapers also have the adverse side effect of diminishing total transmitted power and/or raising the system noise figure. This is readily calculated, and must be considered for overall radar performance prediction. Independent tapers for transmit and receive arrays might be play.

42 ENGINEERING↗
DOE OSTI2026

Notes on Complex (Including Phase-Only) Tapered Active Array Antenna Performance

Modern Active Electronically Steerable Array (AESA) antennas offer substantial control over transmit and receive antenna beam forming, including via elemental weighting to achieve a desired tapered aperture. Elemental taper weighting may generally be complex, with both amplitude and phase components. This includes phase-only tapers. However, array tapers may also have the adverse side effect of diminishing transmit and/or receive effectiveness. This is readily calculated, and must be ...

Doerry, Armin Walter [Sandia National Laboratories↗
DOE OSTI2021

Experimental studies of plasma-antenna coupling with the JET Alfven Eigenmode Active Diagnostic

This paper presents a dedicated study of plasma-antenna (PA) coupling with the Alfven Eigenmode Active Diagnostic (AEAD) in JET. Stable AEs and their resonant frequencies f, damping rates gamma < 0, and toroidal mode numbers n are measured for various PA separations and limiter versus X-point magnetic configurations. Two stable AEs are observed to be resonantly excited at distinct low and high frequencies in limiter plasmas. The values of f and n do not vary with PA separation. However, |gamma| increases with PA separation for the low-f, but not high-f, mode, yet this may be due to slightly different edge conditions. The high-f AE is detected throughout the transition from limiter to X-point configuration, though its damping rate increases; the low-f mode, on the other hand, becomes unidentifiable. The linear resistive MHD code CASTOR is used to simulate the frequency scan of an AEAD-like external antenna. For the limiter pulses, the high-f mode is determined to be an n = 0 GAE, while the low-f mode is likely an n = 2 TAE. During the transition from limiter to X-point configuration, CASTOR indicates that n = 1 and 2 EAEs are excited in the edge gap. These results extend previous experimental studies in JET and Alcator C-Mod; validate the computational work performed by Dvornova et al 2020 Phys. Plasmas 27 012507; and provide guidance for the optimization of PA coupling in upcoming JET energetic particle experiments, for which the AEAD will aim to identify the contribution of alpha particles to AE drive during the DT campaign.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Ultra-rapid, physics-based development pathway for reactor-relevant RF antenna materials

This paper presents a rapid, atomistically-informed, experimental development pathway for fusion reactor-relevant radio frequency (RF) antenna materials in the Cu-Cr-(Nb,Al,Zr) composition system, with the goal of improving upon GRCop-84. RF antennas in a tokamak fusion reactor will face a unique set of challenges as both structural and functional materials. The desired material must simultaneously achieve and maintain high electrical conductivity, high strength, high thermal conductivity, resist high temperatures, possess low nuclear activation, and incur low damage due to neutron bombardment. The GRCop-84 alloy serves as a starting point for iterative improvement, with the desire to reduce or eliminate Nb from the material to minimize nuclear activation. The rapid development pathway makes use of a multi-target combinatorial thick film sputtering process to produce full ternary phase diagrams on a Si wafer substrate. Transient grating spectroscopy (TGS), a laser-ultrasonic method, will determine spatially-varying thermo-elastic properties, while four terminal electrical conductivity measurements will map out the best per- forming regions of the sample for in-depth study at larger length scales. High energy proton and self-ion irradiation emulates the effects of neutron damage on the thermal/electric properties. With rapid turnaround time (∼days) in terms of mapping radiation damage-induced material property changes in the full ternary system, these techniques allow rapid iteration towards an optimal material, testing hundreds of nearby compositions in the time it took to test one. Focused testing of larger, single composition samples (produced in an arc furnace or by laser sintering) provides data on structural and high power RF properties, and validates our thick-film based workflow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Microfabricated ion trap chip with an integrated microwave antenna

An ion trap chip, which may be used for quantum information processing and the like, includes an integrated microwave antenna. The antenna is formed as a radiator connected by one of its ends to the center trace of a microwave transmission line and connected by its other end to a current return path through a ground trace of the microwave transmission line. The radiator includes several parallel, coplanar radiator traces connected in series. The radiator traces are connected such that they all carry electric current in the same direction, so that collectively, they simulate a single, unidirectionally flowing sheet of current. In embodiments, induced currents in underlying metallization planes are suppressed by parallel slots that extend in a direction perpendicular to the radiator traces.

Nordquist, Christopher↗
DOE OSTI2022

Method for tuning an electrically small antenna

A method of tuning an electrically small antenna comprising a radiating element and a support structure comprises applying a force to the support structure to change a shape or a dimension of the radiating element to increase or decrease a frequency at which the electrically small antenna resonates.

Byers, Kyle J.↗
DOE OSTI2022

Integrated energy harvesting transceivers and transmitters with dual-antenna architecture for miniaturized implants and electrochemical sensors

Systems and methods for utilizing a small form-factor, wirelessly powered transceiver are disclosed. In one embodiment, a wireless powered transceiver includes a receive antenna configured to receive a receive signal, a transmit antenna configured to transmit a transmit signal, a power harvesting system including a rectifier circuit configured convert radio frequency energy from the receive signal into DC (direct current) voltage, and a power management unit (PMU) configured to set the operating mode and biasing condition of the receive and transmit circuitry blocks and provide DC voltage from the receive circuitry block to the transmit circuitry block to maintain a minimum voltage, a receiver circuitry block configured to provide energy from the receive signal to the power harvesting system, and a transmitter circuitry block including a data modulator circuit, the data modulator circuit configured to generate the transmit signal using DC voltage received from the power management unit.

Babakhani, Aydin↗
DOE OSTI2023

Modular base for an antenna array

A base configured to be joined with other bases to form a substrate for an antenna array comprises a body, a plurality of male interconnecting features, and a plurality of female interconnecting features. The body includes a front surface and a rear surface and a plurality of edges positioned therebetween. The front surface or the rear surface is configured to retain an antenna. The male interconnecting features of a first base connect with the female interconnecting features of a second base when the first base is joined with the second base to form the substrate or a portion of the substrate.

Furman, Nicholas J.↗
DOE OSTI2023

Artificial photosynthetic devices utilizing polariton antennas

An organic photovoltaic device comprises a substrate, a reflector positioned over the substrate, a first electrode positioned over at least a first portion of the reflector, a polaritonic antenna layer positioned over a second portion of the reflector different from the first portion, electrically connected to the first electrode, and at least one unit reaction cell positioned over at least part of the first electrode, the at least one unit reaction cell comprising a heterojunction layer comprising a donor material and an acceptor material, positioned over the first electrode, and a second electrode positioned over the heterojunction, wherein the polaritonic antenna and the reflector are configured to convert incoming photonic energy to polaritons. A method of fabricating an organic photovoltaic device is also disclosed.

Hou, Shaocong↗
DOE OSTI2024

Integrated energy harvesting transceivers and transmitters with dual-antenna architecture for miniaturized implants and electrochemical sensors

Systems and methods for utilizing a small form-factor, wirelessly powered transceiver are disclosed. In one embodiment, a wireless powered transceiver includes a receive antenna configured to receive a receive signal, a transmit antenna configured to transmit a transmit signal, a power harvesting system including a rectifier circuit configured convert radio frequency energy from the receive signal into DC (direct current) voltage, and a power management unit (PMU) configured to set the operating mode and biasing condition of the receive and transmit circuitry blocks and provide DC voltage from the receive circuitry block to the transmit circuitry block to maintain a minimum voltage, a receiver circuitry block configured to provide energy from the receive signal to the power harvesting system, and a transmitter circuitry block including a data modulator circuit, the data modulator circuit configured to generate the transmit signal using DC voltage received from the power management unit.

Babakhani, Aydin↗
DOE OSTI2020

Loop Antennas for Use On/Off Ground Planes

Many applications benefit from the ability of an RFID tag to operate both on and off a conducting ground plane. This paper presents an electrically small loop antenna at 433 MHz that passively maintains its free-space tune and match when located a certain distance away from a large conducting ground plane. The design achieves this using a single radiation mechanism (that of a loop) in both environments without the use of a ground plane or EBG/AMC structure. An equivalent circuit model is developed that explains the dual-environment behavior and shows that the geometry balances inductive and capacitive parasitics introduced by the ground plane such that the free-space loop reactance, and thus resonant frequency, does not change. A design equation for balancing the inductive and capacitive parasitic effects is derived. Finally, experimental data showing the design eliminates ground plane detuning in practice is presented. The design is suitable for active, “hard” RFID tag applications.

42 ENGINEERING↗
DOE OSTI2025

Waveform modelling for the Laser Interferometer Space Antenna

LISA, the Laser Interferometer Space Antenna, will usher in a new era in gravitational-wave astronomy. As the first anticipated space-based gravitational-wave detector, it will expand our view to the millihertz gravitational-wave sky, where a spectacular variety of interesting new sources abound: from millions of ultra-compact binaries in our Galaxy, to mergers of massive black holes at cosmological distances; from the early inspirals of stellar-mass black holes that will ultimately venture into the ground-based detectors’ view to the death spiral of compact objects into massive black holes, and many sources in between. Central to realising LISA’s discovery potential are waveform models, the theoretical and phenomenological predictions of the pattern of gravitational waves that these sources emit. This White Paper is presented on behalf of the Waveform Working Group for the LISA Consortium. It provides a review of the current state of waveform models for LISA sources, and describes the significant challenges that must yet be overcome.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2026

Enhancing X-ray Sensitivity via the Antenna Effect in Quantum Shells with Multiexciton Emission

Quantum shells (QSs) with efficient multiexciton emission can generate multiple excitons per particle under high-energy excitation, thereby improving exciton utilization under intense X-ray exposure and offering strong potential for X-ray-based scintillation applications. However, these QSs are typically composed of low-atomic-number (Z) elements, which substantially limits their X-ray absorption efficiency and leads to poor X-ray sensitivity. Here, we overcome this fundamental limitation by introducing a high-Z antenna-sensitization strategy that couples QSs to heavy-element molecular absorbers, which act as X-ray harvesting centers and funnel energy into the QSs via efficient interfacial transfer. By combining enhanced X-ray absorption with efficient interfacial energy transfer and improved exciton utilization, we achieve more than an order-of-magnitude increase in multiexciton-driven QS radioluminescence (RL) relative to pristine shells. Additionally, a high X-ray imaging resolution of 25.2 lp mm –1 was achieved, exceeding the performance of most previously reported X-ray imaging scintillators. These findings offer a promising design strategy for advancing QS-based materials toward high-performance X-ray imaging applications.

antenna effect↗
DOE OSTI2023

Assessment and Performance of Flexible Quench Antenna Array Diagnostics for Superconducting Magnets

FNAL has been developing multiple versions of flexible quench antennas (flex-QA), including some specially optimized for high sensitivity and/or high resolution, to characterize quench events and transients during current ramping in superconducting magnets. A fundamental feature in our use of these is the creation of grid-like structures of sensitive elements to cover coil surfaces, with the aim of getting precise localization of magnetic flux-change events. The flex-QA are coupled with fast data-acquisition, allowing comprehensive analysis of signals at the relevant fine time scales. In addition to arrays of various flex-QA types being used during cryogenic testing of superconducting magnets, we also are utilizing a newly developed room temperature test stand to better understand QA response characteristics. The data from actual superconducting magnet tests, warm test stand measurements, and simulation data on the same QA designs allows us to draw conclusions on operational feasibility and plan better for improvements of our sensors. In this paper we present data from the multiple tests performed and analysis results. Flex-QA designs are compared, and their features, options, and optimization discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Real-Time High-Accuracy Digital Wireless Time, Frequency, and Phase Calibration for Coherent Distributed Antenna Arrays

his work presents a fully-digital high-accuracy real-time calibration procedure for frequency and time alignment of open-loop wirelessly coordinated coherent distributed antenna array (CDA) modems, enabling radio frequency (RF) phase coherence of spatially separated commercial off-the-shelf (COTS) software-defined radios (SDRs) without cables or external references such as the global navigation satellite system (GNSS). Building on previous work using high-accuracy spectrally-sparse time of arrival (ToA) waveforms and a multistep ToA refinement process, a high-accuracy two-way time transfer (TWTT)-based time–frequency coordination approach is demonstrated. Due to the two-way nature of the high-accuracy TWTT approach, the time and frequency estimates are Doppler and multipath tolerant, so long as the channel is reciprocal over the synchronization epoch. This technique is experimentally verified using COTS SDRs in a lab environment in static and dynamic scenarios and with significant multipath scatterers. Time, frequency, and phase stability were evaluated by beamforming over coaxial cables to an oscilloscope which achieved time and phase precisions of ~60– 70 ps , with median coherent gains above 99% using optimized coordination parameters, and a beamforming frequency root-mean-square error (RMSE) of 3.73 ppb in a dynamic scenario. Finally, experiments were conducted to compare the performance of this technique with previous works using an analog continuous-wave two-tone (CWTT) frequency reference technique in both static and dynamic settings.

Clock synchronization↗
DOE OSTI2021

The PshX subunit of the photochemical reaction center from Heliobacterium modesticaldum acts as a low-energy antenna

The anoxygenic phototrophic bacterium Heliobacterium modesticaldum contains a photochemical reaction center protein complex (called the HbRC) consisting of a homodimer of the PshA polypeptide and two copies of a newly discovered polypeptide called PshX, which is a single transmembrane helix that binds two bacteriochlorophyll g molecules. Here, to assess the function of PshX, we produced a ΔpshX strain of Hbt. modesticaldum by leveraging the endogenous Hbt. modesticaldum Type I-A CRISPR-Cas system to aid in mutant selection. We optimized this system by separating the homologous recombination and CRISPR-based selection steps into two plasmid transformations, allowing for markerless gene replacement. Fluorescence and low-temperature absorbance of the purified HbRC from the wild-type and ΔpshX strains showed that the bacteriochlorophylls bound by PshX have the lowest site energies in the entire HbRC. This indicates that PshX acts as a low-energy antenna subunit, participating in entropy-assisted uphill energy transfer towards the P 800 special bacteriochlorophyll g pair. We further discuss the role that PshX may play in stability of the HbRC, its conservation in other heliobacterial species, and the evolutionary pressure to produce and maintain single-TMH subunits in similar locations in other reaction centers.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2023

Cosmology with the Laser Interferometer Space Antenna

The Laser Interferometer Space Antenna (LISA) has two scientific objectives of cosmological focus: to probe the expansion rate of the universe, and to understand stochastic gravitational-wave backgrounds and their implications for early universe and particle physics, from the MeV to the Planck scale. However, the range of potential cosmological applications of gravitational-wave observations extends well beyond these two objectives. This publication presents a summary of the state of the art in LISA cosmology, theory and methods, and identifies new opportunities to use gravitational-wave observations by LISA to probe the universe.

79 ASTRONOMY AND ASTROPHYSICS↗