Results for “sinter” — Page 57

DOE OSTI2020

Solid state grain alignment of permanent magnets in near-final shape

Magnet microstructure manipulation in the solid state by controlled application of a sufficient stress in a direction during high temperature annealing in a single-phase region of heat-treatable magnet alloys, e.g., alnico-type magnets is followed by magnetic annealing and draw annealing to improve coercivity and saturation magnetization properties. The solid-state process can be termed highly controlled abnormal grain growth (hereafter AGG) and will make aligned sintered anisotropic magnets that meet or exceed the magnetic properties of cast versions of the same alloy types.

Anderson, Iver E.↗

DOE OSTI2021

MADE3D: Enabling the Next-Generation High-Torque- Density Wind Generators by Additive Design and 3D Printing

Direct-drive wind turbine generators are increasing in popularity, thanks to recent project developments - especially offshore, where reliability and efficiency are major cost drivers. Yet, high capital costs are forcing many original equipment manufacturers to consider lightweight, high-torque density generators for next-generation multi-megawatt turbines that may be difficult to realize by traditional design or manufacturing methods. In this study, we present a new design framework enabled by advanced machine learning and multimaterial additive manufacturing to perform a magnetic topology optimization that maximizes the torque per rotor active mass for a 15-megawatt direct-drive permanent magnet wind generator. A comparison of the proposed approach against conventional topology optimization demonstrated a significant increase in computational efficiency and accuracy in performance predictions. Results using single and multimaterial compositions for rotor core and magnets identify a wider choice of 3D printable designs for a given specification. A hybrid combination of sintered and dysprosium-free polymer-bonded magnets shows good potential for torque performance by saving material costs up to 8.75%. More than 30% improvement in rotor torque densities is identified which can marginally improve the overall generator torque density. With the rapid evolution of multipowder deposition technologies, this study can greatly inspire a new paradigm for design-driven manufacturing with novel material compositions and lightweight, low-cost, high-strength multimaterial geometries that were previously unexplored for direct-drive generators.

3D printing↗

DOE OSTI2021

Metal infiltrated electrodes for solid state batteries

Disclosed are electrochemical devices and methods for making electrochemical devices such as metal infiltrated electrodes for solid state lithium ion and lithium metal batteries. In one method for forming an electrode, a metal is infiltrated into the pore space of the active material of the electrode providing improved electronic conductivity to the electrode. The electrode may also include a solid-state ion conducting material providing improved ion conductivity to the electrode. Before infiltration of the metal, a stabilization coating may be applied to the active material and/or the solid-state ion conducting material to the stabilize electrode interfaces by slowing, but not eliminating, the chemical reactions that occur at elevated temperatures during sintering of the active material and/or the solid-state ion conducting material forming the electrode.

Sakamoto, Jeffrey↗

DOE OSTI2021

Rapid consolidation method for preparing bulk metastable iron-rich materials

Interstitially modified compounds of rare earth element-containing, iron-rich compounds may be synthesized with a ThMn 12 tetragonal crystal structure such that the compounds have useful permanent magnet properties. It is difficult to consolidate particles of the compounds into a bulk shape without altering the composition and magnetic properties of the metastable material. A combination of thermal analysis and crystal structure analysis of each compound may be used to establish heating and consolidation parameters for sintering of the particles into useful magnet shapes.

Zhou, Chen↗

DOE OSTI2021

Compositions and methods for thermoelectric ceramics

In one aspect, the disclosure relates to thermoelectric ceramic oxide compositions comprising a CaMnO 3 ceramic. In a further aspect, the disclosed thermoelectric ceramic oxide compositions can dramatically increase the energy conversion efficiency of thermoelectric through a combination of modifying the chemistry of precursor materials, and simultaneously introducing a metal oxide liquid phase during sintering. In a further aspect, the present disclosure pertains to thermoelectric ceramic oxide compositions comprising a metal doped CaMnO 3 having with a metal oxide grain boundary phase; wherein the metal is selected from group 13, group 14, group 15, group 16, or a rare earth element. In a still further aspect, the disclosure relates to methods for making the thermoelectric ceramic oxide materials. This abstract is intended as a scanning tool for purposes of searching in the particular art and is not intended to be limiting of the present disclosure.

Song, Xueyan↗

DOE OSTI2021

Solid-state batteries and the critical role of interfaces

The Grand Challenge for the next generation of energy storage technologies is no longer the identification of electroactive cathode or anode materials thanks to extensive worldwide synthesis efforts along with theory and modeling like the Materials Project.1 Instead, the critical challenges revolve around assembling materials in the right architecture to achieve maximum performance and cell life at reasonable temperatures and pressures. Nowhere is this more critical than on the next generation of energy storage technologies revolving around all solid-state batteries. These batteries are the ultimate challenge for materials science requiring new ways to assemble multiple dissimilar materials such that: (1) interfaces are optimized to facilitate ion motion across the different compounds while (2) maintaining chemical stability and (3) simultaneously preserving the crystal structures of each phase during (4) large volume changes due to shuttling of lithium, at (5) room temperature and under (6) atmospheric pressure. To address these requirements will require insights and expertise from research fields outside the traditional lithium-ion battery community such as solid oxide fuel cells, synthesis science, barrier layers, interface formers, sintering, and mechanical properties.

25 ENERGY STORAGE↗

DOE OSTI2021

Atomic Layer Deposition for Improved Biomass Conversion Catalysts

Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation and Scale-Up Center at NREL and various industrial partners to develop scalable and cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. The substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating weakened the adsorption strength of hydrogenation surface intermediates, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for the production of sustainable aviation fuel (SAF) and the oxidation of glucose to bio-derived gluconic acid.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2021

Atomic Layer Deposition for Improved Biomass Conversion Catalysts

Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation & Scale-Up Center at NREL and various industrial partners to develop scalable, cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. Substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating influenced the adsorption strength of hydrogenation surface intermediates in unexpected ways, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for production of sustainable aviation fuel (SAF) and the oxidation of glucose for bio-derived gluconic acid. Recent findings from these experimental campaigns will also be shared. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts and this work constitutes an important examination of the impact of ALD coatings in a variety of reaction environments.

bioenergy↗

DOE OSTI2021

Atomic Layer Deposition for Improved Biomass Conversion Catalysts

Heterogeneous catalysts are a key enabler of the transition towards a sustainable, bio-based economy for fuels and chemicals. However, the harsh conditions in many biomass conversion processes lead to nanoparticle sintering, support collapse, and metal leaching in conventional PGM catalysts. Next-generation catalysts must be developed to address these stability challenges. This presentation will discuss ongoing work between the Catalytic Carbon Transformation and Scale-Up Center at NREL and various industrial partners to develop scalable and cost-effective atomic layer deposition (ALD) coatings for improving the performance of biomass conversion catalysts. The substantial focus will be devoted to the benefits of TiO2 ALD coatings on supported Pd hydrogenation catalysts. Ten cycles of TiO2 ALD were found to dramatically improve the activity of a conventional Pd/Al2O3 catalyst towards aromatic hydrogenation, despite partial coverage of the Pd sites by the ALD layer. Subsequent advanced characterization and atomic-scale computational modeling revealed that the ALD coating weakened the adsorption strength of hydrogenation surface intermediates, leading to higher reaction rates. Reaction testing after exposure to sulfur impurities, high temperature oxidation, and hydrothermal treatment demonstrated the improved stability of the ALD-coated catalyst. Additionally, the ALD synthesis process was found to be scalable over two orders of magnitude with minimal deviation in synthesized catalyst properties. These results were contextualized with cost models of industrial ALD coating and aromatic hydrogenation processes to further refine the value proposition of ALD coatings. Given the demonstrated improvements in hydrogenation, TiO2 ALD coatings have also been applied to supported Pt catalysts for use in other biomass conversion reactions, such as hydrodeoxygenation for the production of sustainable aviation fuel (SAF) and the oxidation of glucose to bio-derived gluconic acid. Recent findings from these experimental campaigns will also be shared. ALD technology holds great potential in the development of next-generation catalysts for biofuels and bioproducts, and this work constitutes an important examination of the impact of ALD coatings in a variety of reaction environments.

atomic layer deposition↗

DOE OSTI2021

Apparatus and method for three-dimensional metal printing

An apparatus and device for building an article by additive manufacturing or 3-D printing. The method includes feeding a supply of particulate slurry to and through a nozzle, such as including an integrated pump, to form a plurality of beads and layers of the slurry on a deposition surface, and ultimately forming a desirable article from the layers of deposited material. The liquid phase of the slurry is desirably removed by heat, and the deposited layers can be sintered or otherwise fused as needed.

Klett, James W.↗

DOE OSTI2021

Process for fabrication of enhanced β″-alumina solid electrolytes for energy storage devices and energy applications

A dense β″-alumina/zirconia composite solid electrolyte and process for fabrication are disclosed. The process allows fabrication at temperatures at or below 1600° C. The solid electrolytes include a dense composite matrix of β″-alumina and zirconia, and one or more transition metal oxides that aid the conversion and densification of precursor salts during sintering. The composite solid electrolytes find application in sodium energy storage devices and power-grid systems and devices for energy applications.

Lu, Xiaochuan↗

DOE OSTI2021

Nanowire-based hydrodesulfurization catalysts for hydrocarbon fuels

The present development is a metal particle coated nanowire catalyst for use in the hydrodesulfurization of fuels and a process for the production of the catalyst. The catalyst comprises titanium(IV) oxide nanowires wherein the nanowires are produced by exposure of a TiO2—KOH paste to microwave radiation. Metal particles selected from the group consisting of molybdenum, nickel, cobalt, tungsten, or a combination thereof, are impregnated on the metal oxide nanowire surface. The metal impregnated nanowires are sulfided to produce catalytically-active metal particles on the surface of the nanowires The catalysts of the present invention are intended for use in the removal of thiophenic sulfur from liquid fuels through a hydrodesulfurization (HDS) process in a fixed bed reactor. The presence of nanowires improves the HDS activity and reduces the sintering effect, therefore, the sulfur removal efficiency increases.

Sunkara, Mahendra Kumar↗

DOE OSTI2022

Electromagnetics and Advanced Manufacturing Simulation Development within the MOOSE Ecosystem

The MOOSE electromagnetics module (EMM) was developed to provide a general simulation tool for modeling a wide range of problems encountered in computational electromagnetics and enable MOOSE and MOOSE-based application coupling to Maxwell's equations to solve a wide class of new problems. Development of the electromagnetics module has also enabled development of new advanced manufacturing models in the MOOSE ecosystem, including that of the electric field-assisted sintering (EFAS) process. Recent results from this effort show good agreement with experimental results, and these two capabilities will be used in future projects to develop models for novel materials development and manufacturing for extreme environments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Nanowire-based hydrodesulfurization catalysts for hydrocarbon fuels

The present development is a metal particle coated nanowire catalyst for use in the hydrodesulfurization of fuels and a process for the production of the catalyst. The catalyst comprises titanium(IV) oxide nanowires wherein the nanowires are produced by exposure of a TiO2—KOH paste to microwave radiation. Metal particles selected from the group consisting of molybdenum, nickel, cobalt, tungsten, or a combination thereof, are impregnated on the metal oxide nanowire surface. The metal impregnated nanowires are sulfided to produce catalytically-active metal particles on the surface of the nanowires The catalysts of the present invention are intended for use in the removal of thiophenic sulfur from liquid fuels through a hydrodesulfurization (HDS) process in a fixed bed reactor. The presence of nanowires improves the HDS activity and reduces the sintering effect, therefore, the sulfur removal efficiency increases.

Sunkara, Mahendra K.↗

DOE OSTI2020

Binderjet Additive Manufacturing for Complex Heat Exchanger Geometries

Concentrated Solar Power (CSP) systems play a role in the worlds development of renewable energy. Mirrors are used to concentrate sunlight that is converted into electricity or other forms of useful energy. CSP impact depends significantly on its overall economics. The U.S. Department of Energy’s (DOE’s) Solar Energy Technology Office (SETO) cost goals for 2030include $0.05/kWh levelized cost of electricity (LCOE) for a baseload plant [1]. The power cycle cost goal is $900/kWe [1]. The envisioned recompression supercritical carbondioxide (sCO2) power cycle includes four heat exchangers, which together are at least ¾ of the total power cycle cost. Meeting the cost target requires reducing the heat exchanger cost. The 260 bar and 588 °C heat exchanger requirements are challenging. Shell and tube heat exchangers can meet the requirements, but the size and cost are prohibitive. State-of-the-art diffusion bonded printed circuit heat exchanger designs are 3 m3 or larger and expensive to manufacture. Additive manufacturing enables novel heat exchanger geometries that can reduce heat exchanger size and mass [2]. Binderjet technology is an additive manufacturing modality. It selectively deposits binder material onto the powder bed to form a solid part one layer at a time. Once applied, the binder is cured, the remaining powder removed, and the part heat treated in steps to remove the binder, sinter the metal powder, and densify the part. The Binderjet printing process is more than 10x faster than the best-known metal additive modality, direct metal laser melting (DMLM), thus enabling 10x the part through-put rate [3]. The high throughput rate results in a low-cost manufacturing process capable of creating complex heat exchanger geometries. This paper introduces a complex heat exchanger geometry and methods of Binderjet processing to fabricate the geometry.

Barua, Ananda↗

DOE OSTI2022

High Volume Production of Nanoscale Elements

The utility of nanoscale elements spans numerous potential markets including healthcare, communications, energy, optics, and structures. The energy market in particular will require large volumes and is price sensitive. In this talk we will discuss strategies to scale nanoscale elements, including nanoparticle inks and nanoscale thin films, for the large area deposition (hundreds of square meters) using high through put processes. Historically, roll-to-roll production of thin films has been carried out at very high speeds over large areas using solution phase inks. Nanoparticles are produced in a bottom-up approach in solution phase that simplifies the processing and is amenable to ink formulations. Sintering and annealing of the thin films can be increased by using radiation thermal processing that integrates easily into roll-to-roll manufacturing. Results of printed films on the order of tens of nanometers to hundreds of nanometers are presented including studies of morphologies and uniformity over large areas. Solar cells devices using the roll-to-roll setup are demonstrated and a techno-economic analysis of the manufacturing is proposed. These results are presented with a comparison to the current photovoltaic technologies in production.

Druffel, Thad↗

DOE OSTI2022

Solid state grain alignment of permanent magnets in near-final shape

Magnet microstructure manipulation in the solid state by controlled application of a sufficient stress in a direction during high temperature annealing in a single-phase region of heat-treatable magnet alloys, e.g., alnico-type magnets is followed by magnetic annealing and draw annealing to improve coercivity and saturation magnetization properties. The solid-state process can be termed highly controlled abnormal grain growth (hereafter AGG) and will make aligned sintered anisotropic magnets that meet or exceed the magnetic properties of cast versions of the same alloy types.

Anderson, Iver E.↗

DOE OSTI2022

Development of a Laser Ultrasonics-based Approach for Rapid Screening of High Entropy Alloys

This project utilized a laser ultrasonic technique to systematically study temperature-induced evolution of material properties in a set of interrelated binary alloys and a high entropy alloy (HEA) fabricated using arc-melting and spark plasma sintering processes. This technique involved the use of a nanosecond duration, high-intensity pulsed laser to thermo-elastically generate ultrasonic waves that propagate in the bulk of the metal alloy. Sub-nanometer-scale displacements associated with the propagating bulk ultrasonic waves were detected along the epicenter on the opposite surface of the sample using a 1 GHz bandwidth photorefractive interferometer. Phase transformations and microstructural changes were inferred from the temperature-dependent trends in the bulk acoustic velocities and features in the ultrasonic epicentral waveforms measured in the binary alloys. These inferences were then correlated with electron/optical microscopy observations and predictions using calculations of phase diagrams (CALPHAD). The results showed that the laser-generated ultrasonic pulses were strongly influenced by changes in material microstructure and could accurately track thermally driven phase transformations and detect the presence of microscale heterogeneities (grain boundaries, dendritic structures, etc.) in the set of binary alloy samples. The measurement approach was then applied to a quinary HEA sample for estimating phase transition temperature and determining microstructural heterogeneity. The rapid, non-contact and non-destructive ultrasonic testing approach demonstrated here is amenable to high throughput combinatorial investigations that can be applied to graded composition HEAs produced using advanced manufacturing methods. When paired with atomistic simulations and CALPHAD modeling, this approach can overcome the bottlenecks faced by current material characterization methods in efficiently screening the vast discovery space of HEAs that spans over a hundred million unique quinary alloy compositions.

36 MATERIALS SCIENCE↗