Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,009 records · Page 56
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Flexural Fatigue Testing and Qualification of Hybrid PAN-pitch Composite Materials with High Through-Thickness Thermal Conductivity

Carbon-fiber-reinforced polymers (CFRPs) considered for motor components within future electric vertical takeoff and landing (eVTOL) vehicles require not only a high strength-to-weight ratio but also a high through-thickness thermal conductivity (TC) to dissipate heat. Previously, CFRPs incorporating pitch CF interleaves demonstrated an increased through-thickness TC relative to the baseline composite, but the effect on flexural fatigue life was not evaluated. For this work, T700S/TC275–1 braided carbon fiber/epoxy prepreg baseline (no interleave), YSH–60A pitch interleave, and YS–80A pitch interleave configurations were tested for fatigue life. A combination of ASTM International Standards D7264 and D3479 were used to develop a reliable testing method. An Instron® (Illinois Tool Works Inc.) 8501 servohydraulic system with a fatigue test fixture was set up with a 16:1 span:thickness ratio, load ratio R set to 0.1, and frequency of 4 Hz. High-cycle fatigue testing was completed, and it was found that YSH–60A interleave performed slightly better than YS–80A below 100,000 cycles but showed no differences above 100,000 cycles. In all cases, the baseline CFRP had superior fatigue life performance both in terms of stress handled and total cycles to failure. These fatigue testing data will inform future use of hybrid CFRP materials by highlighting the tradeoff between increased through-thickness TC and fatigue life. Testing guidelines, equipment, and parameters for static and fatigue tests were successfully outlined for CFRPs.

composites↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design With and Without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRSDate not supplied

Bypass Duct Acoustic Liner Design with and without Bifurcation Effects

The growth in air traffic and the commitment to sustainable aviation continue to provide new challenges to reducing aircraft noise levels. Acoustic liner design methodologies must therefore provide the capability to efficiently predict the acoustic benefits of novel liner configurations within complex aircraft nacelle geometries. With these observations in mind, a broadband acoustic liner optimization process has been developed and assessed through a series of design and experimental studies at increasing technology readiness levels. This work applies the design process to the aft-fan noise component and explores the effects of bypass duct bifurcations (e.g., the pylon and lower bifurcation). In addition to this new application, the design study is expanded to include the use of a commercially available duct propagation code. Despite the different general workflow for the two propagation codes, consistent optimized impedance spectra and in-duct attenuation predictions were obtained for several acoustic treatment options. The preliminary results are promising, and this work increases confidence in the enhanced broadband liner design methodology and lays the groundwork for complimentary use of the codes in future studies. The potential benefits of acoustic treatment on the upper and lower bifurcations are also demonstrated. The knowledge gained through this preliminary stage of the liner design process will be used to guide the identification of candidate liner designs for a proposed static engine test within the next year.

Acoustic Liner Design↗
NASA NTRSDate not supplied

Scale Resolving Simulations of Viking '75 Reentry Capsule Wake Flow

Scale resolving simulations of static wake tests of the '75 Viking capsule have been performed using two unstructured grid flow solvers, US3D and PyFR. Simulations with several resolutions have been performed at varying Mach numbers with the aim of solver validation for capsule wake flows as well as establishing simulation best practices.

Rathakrishnan Bhaskaran↗
NASA NTRSDate not supplied

Scale-Resolving Simulations of Viking '75 Reentry Capsule Wake Flow

Scale resolving simulations of static wake tests of the '75 Viking capsule have been performed using two unstructured grid flow solvers, US3D and PyFR. Simulations with several resolutions have been performed at varying Mach numbers with the aim of solver validation for capsule wake flows as well as establishing simulation best practices.

Rathakrishnan Bhaskaran↗
NASA NTRSDate not supplied

Evaluation of Particle Degradation of a Ytterbium Disilicate Gas Turbine Coating in a Combustion Environment

Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.

Jamesa L Stokes↗
NASA NTRSDate not supplied

Evaluation of Particle Degradation of a Ytterbium Disilicate Gas Turbine Coating in a Combustion Environment

Ytterbium disilicate (Yb2Si2O7) is a state-of-the-art topcoat material used in environmental barrier coatings (EBCs) to protect SiC-SiC composites from water vapor corrosion in gas turbine engines. However, it’s degradation by thermochemical and thermomechanical particle interactions may limit its use in next generation engine systems. Several static furnace tests have been performed on Yb2Si2O7 to elucidate methods of degradation, although dynamic testing in an engine-relevant environment has not been carried out. Ultimately, testing and evaluation of materials that incorporates all environmental damage modes will allow for an accurate assessment of long-term durability and operating lifetime. This work details the investigation of particle-induced erosion and corrosion of Yb2Si2O7 in NASA Glenn’s Erosion Burner Rig Facility. Coating durability was investigated as a function of test temperature, particle size, and deposition rate. Thermal cycling was also incorporated into testing to determine the interplay of heating/cooling cycles with particle degradation. Overall, these analyses will be used to determine coating robustness in an engine relevant environment.

Jamesa L Stokes↗
NASA NTRS1985

Port geometry effects on thrust reverser static performance

An investigation has been conducted to provide some insight into the effect of several geometric parameters on the internal performance of thrust reverser ports for nonaxisymmetric nozzles using a single port test apparatus. This test apparatus simulates thrust reversal (conceptually) which would occur in the convergent section of the forward flight nozzle or in the constant area duct just upstream. The port opening had an aspect ratio of 6.1 (throat width/throat height) and had constant passage area from the geometric throat to the exit. The geometric parameters investigated were port angle, port corner radius, port location, and flow blocker angle. The apparatus had a single port so that thrust (vector) angle could be obtained from force balance measurements. The tests were conducted in the Static Test Stand of the Langley 16-Foot Transonic Tunnel at nozzle pressure ratios from 1.5 to 8.0 using high pressure air for propulsion simulation. Port angles (measured forward from a horizontal reference line) investigated were 75, 90, 120 and 135 deg. Sharp and rounded port corners were investigated for each port angle. Discharge coefficient, thrust ratio, and passage static pressures were measured.

Re, R. J.↗
NASA NTRS2006

Quasi-Static 3-Point Reinforced Carbon-Carbon Bend Test and Analysis for Shuttle Orbiter Wing Leading Edge Impact Damage Thresholds

Static 3-point bend tests of Reinforced Carbon-Carbon (RCC) were conducted to failure to provide data for additional validation of an LS-DYNA RCC model suitable for predicting the threshold of impact damage to shuttle orbiter wing leading edges. LS-DYNA predictions correlated well with the average RCC failure load, and were good in matching the load vs. deflection. However, correlating the detectable damage using NDE methods with the cumulative damage parameter in LS-DYNA material model 58 was not readily achievable. The difficulty of finding internal RCC damage with NDE and the high sensitivity of the mat58 damage parameter to the load near failure made the task very challenging. In addition, damage mechanisms for RCC due to dynamic impact of debris such as foam and ice and damage mechanisms due to a static loading were, as expected, not equivalent.

Fasanella, Edwin L.↗
NASA NTRS1942

The direct-stress fatigue strength of 17S-T aluminum alloy throughout the range from 1/2 to 500,000,000 cycles of stress

Fatigue-test were conducted on six specimens made from 3/4-inch-diameter 17S-T rolled-and-drawn rod for the purpose of obtaining additional data on the fatigue life of the material at stresses up to the static strength. The specimens were tested in direct tension using a stress range from zero to a maximum in tension. A static testing machine was used to apply repeated loads in the case of the first three specimens; the other three specimens were tested in a direct tension-compression fatigue machine. The direct-stress fatigue curve obtained for the material indicates that, in the range of stresses above about two-thirds the tensile strength, the fatigue strength is higher than might be expected by simply extrapolating the ordinary curve of stress plotted against the number of cycles determined at lower stresses.

Hartmann, E C↗
NASA NTRS1982

Strain rate characterization of unidirectional graphite/epoxy composite

For an investigation of problems of composites at high strain rates with dominant wave propagation effects, such as dynamically loaded composite jet engine blades, the longitudinal, transverse, and in-plane shear properties of unidirectional SP 288/AS graphite/epoxy were measured at various strain rates ranging from quasi-static to over 500/s. The test specimens were rings 10.16 cm in diameter, 2.54 cm long, 6 to 8 plies thick, and with fibers at 0, 90, and 10 deg off-axis. Quasi-static testing was conducted in a fixture which applies hydraulic pressure to the ring specimens, and dynamic testing was conducted by applying an internal pressure pulse through a liquid in a special fixture. Dynamic stress-strain curves are presented. For the 0-deg specimens, the modulus increases with strain up to 20 percent of the static value. The modulus and strength increase sharply in the 90-deg rings with strain rate reaching values two to three times the corresponding static rate.

Daniel, I. M.↗
NASA NTRS1983

Analytical modeling of transport aircraft crash scenarios to obtain floor pulses

The KRAS program was used to analyze transport aircraft candidate crash scenarios. Aircraft floor pulses and seat/occupant responses are presented. Results show that: (1) longitudinal only pulses can be represented by equivalent step inputs and/or static requirements; (2) the L1649 crash test floor longitudinal pulse for the aft direction (forward inertia) is less than 9g static or an equivalent 5g pulse; aft inertia accelerations are extremely small ((ch76) 3g) for representative crash scenarios; (3) a viable procedure to relate crash scenario floor pulses to standard laboratory dynamic and static test data using state of the art analysis and test procedures was demonstrated; and (4) floor pulse magnitudes are expected to be lower for wide body aircraft than for smaller narrow body aircraft.

Wittlin, G.↗
NASA NTRS1991

Measurement of the static and dynamic coefficients of a cross-type parachute in subsonic flow

An experimental parametric investigation of the aerodynamic qualities of cross-type parachutes was performed in a subsonic wind tunnel, using a new experimental technique. This investigation included the measurement of the static and dynamic aerodynamic coefficients, utilizing the measuring apparatus modified specifically for this type of testing. It is shown that the static aerodynamic coefficients of several configurations are in good agreement with available data, and assisted in validating the experimental technique employed. Two configuration parameters were varied in the static tests, the cord length and the canopy aspect ratio, with both parameters having a similar effect on the drag measurement, i.e., any increase in either of them increased the effective blocking area, and therefore the axial force.

Shpund, Zalman↗
NASA NTRS1983

An experimental study of transonic flow about a supercritical airfoil. Static pressure and drag data obtained from tests of a supercritical airfoil and an NACA 0012 airfoil at transonic speeds, supplement

Surface static-pressure and drag data obtained from tests of two slightly modified versions of the original NASA Whitcomb airfoil and a model of the NACA 0012 airfoil section are presented. Data for the supercritical airfoil were obtained for a free-stream Mach number range of 0.5 to 0.9, and a chord Reynolds number range of 2 x 10 to the 6th power to 4 x 10 to the 6th power. The NACA 0012 airfoil was tested at a constant chord Reynolds number of 2 x 10 to the 6th power and a free-stream Mach number range of 0.6 to 0.8.

Spaid, F. W.↗
NASA NTRS2011

Effect of Data Reduction and Fiber-Bridging on Mode I Delamination Characterization of Unidirectional Composites

Reliable delamination characterization data for laminated composites are needed for input in analytical models of structures to predict delamination onset and growth. The double-cantilevered beam (DCB) specimen is used to measure fracture toughness, GIc, and strain energy release rate, GImax, for delamination onset and growth in laminated composites under mode I loading. The current study was conducted as part of an ASTM Round Robin activity to evaluate a proposed testing standard for Mode I fatigue delamination propagation. Static and fatigue tests were conducted on specimens of IM7/977-3 and G40-800/5276-1 graphite/epoxies, and S2/5216 glass/epoxy DCB specimens to evaluate the draft standard "Standard Test Method for Mode I Fatigue Delamination Propagation of Unidirectional Fiber-Reinforced Polymer Matrix Composites." Static results were used to generate a delamination resistance curve, GIR, for each material, which was used to determine the effects of fiber-bridging on the delamination growth data. All three materials were tested in fatigue at a cyclic GImax level equal to 90% of the fracture toughness, GIc, to determine the delamination growth rate. Two different data reduction methods, a 2-point and a 7-point fit, were used and the resulting Paris Law equations were compared. Growth rate results were normalized by the delamination resistance curve for each material and compared to the nonnormalized results. Paris Law exponents were found to decrease by 5.4% to 46.2% due to normalizing the growth data. Additional specimens of the IM7/977-3 material were tested at 3 lower cyclic GImax levels to compare the effect of loading level on delamination growth rates. The IM7/977-3 tests were also used to determine the delamination threshold curve for that material. The results show that tests at a range of loading levels are necessary to describe the complete delamination behavior of this material.

Murri, Gretchen B.↗
NASA NTRS1998

Structural Similitude and Scaling Laws

Aircraft and spacecraft comprise the class of aerospace structures that require efficiency and wisdom in design, sophistication and accuracy in analysis and numerous and careful experimental evaluations of components and prototype, in order to achieve the necessary system reliability, performance and safety. Preliminary and/or concept design entails the assemblage of system mission requirements, system expected performance and identification of components and their connections as well as of manufacturing and system assembly techniques. This is accomplished through experience based on previous similar designs, and through the possible use of models to simulate the entire system characteristics. Detail design is heavily dependent on information and concepts derived from the previous steps. This information identifies critical design areas which need sophisticated analyses, and design and redesign procedures to achieve the expected component performance. This step may require several independent analysis models, which, in many instances, require component testing. The last step in the design process, before going to production, is the verification of the design. This step necessitates the production of large components and prototypes in order to test component and system analytical predictions and verify strength and performance requirements under the worst loading conditions that the system is expected to encounter in service. Clearly then, full-scale testing is in many cases necessary and always very expensive. In the aircraft industry, in addition to full-scale tests, certification and safety necessitate large component static and dynamic testing. Such tests are extremely difficult, time consuming and definitely absolutely necessary. Clearly, one should not expect that prototype testing will be totally eliminated in the aircraft industry. It is hoped, though, that we can reduce full-scale testing to a minimum. Full-scale large component testing is necessary in other industries as well, Ship building, automobile and railway car construction all rely heavily on testing. Regardless of the application, a scaled-down (by a large factor) model (scale model) which closely represents the structural behavior of the full-scale system (prototype) can prove to be an extremely beneficial tool. This possible development must be based on the existence of certain structural parameters that control the behavior of a structural system when acted upon by static and/or dynamic loads. If such structural parameters exist, a scaled-down replica can be built, which will duplicate the response of the full-scale system. The two systems are then said to be structurally similar. The term, then, that best describes this similarity is structural similitude. Similarity of systems requires that the relevant system parameters be identical and these systems be governed by a unique set of characteristic equations. Thus, if a relation or equation of variables is written for a system, it is valid for all systems which are similar to it. Each variable in a model is proportional to the corresponding variable of the prototype. This ratio, which plays an essential role in predicting the relationship between the model and its prototype, is called the scale factor.

Simitses, George J.↗
NASA NTRS1997

Design of Launch Vehicle Flight Control Augmentors and Resulting Flight Stability and Control (Center Director's Discretionary Fund Project 93-05, Part III)

This publication presents the control requirements, the details of the designed Flight Control Augmentor's (FCA's), the static stability and dynamic stability wind tunnel test programs, the static stability and control analyses, the dynamic stability characteristics of the experimental Launch Vehicle (LV) with the designed FCA's, and a consideration of the elastic vehicle. Dramatic improvements in flight stability have been realized with all the FCA designs; these ranged from 41 percent to 72 percent achieved by the blunt TE design. The control analysis showed that control increased 110 percent with only 3 degrees of FCA deflection. The dynamic stability results showed improvements with all FCA designs tested at all Mach numbers tested. The blunt TE FCA's had the best overall dynamic stability results. Since the lowest elastic vehicle frequency must be well separated from that of the control system, the significant frequencies and modes of vibration have been identified, and the response spectra compared for the experimental LV in both the conventional and the aft cg configuration. Although the dynamic response was 150 percent greater in the aft cg configuration, the lowest bending mode frequency decreased by only 2.8 percent.

Barret, C.↗