Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Optimization of catholyte for halide-based all-solid-state batteries

Halide solid electrolytes gain significant attention due to their high ionic conductivity, low processing temperature, dry air compatibility, and high-voltage stability. However, low cathode active material (CAM) loading in the composite cathode constrains the realization of high energy density for halide-based all-solid-state batteries. In this study, three halide materials, raw Li 3 YBrCl 5 (LYBC-R, <30μm), milled LYBC (LYBC-M, <5 μm) and freeze-dried Li 3 InCl 6 (LIC, <500 nm), were used as catholytes, combined with LYBC-M as the electrolyte and LiIn alloy as the anode. The CAM:catholyte ratio was investigated as well as stack pressure and operating temperature. Our study demonstrates that particle size of the catholyte plays an important role only for high CAM loading or high C-rate cycling. At moderate CAM loading (65 and 70wt% LiNi 0.83 Mn 0.06 Co 0.11 O 2 ) and 0.1 C-rate, all the three catholytes perform well, providing initial discharge capacities >177 mAh/g. At high CAM loading (85wt%) and 0.1 C-rate, a cathode with the nano-scale LIC catholyte provides discharge capacity of 175 mAh/g, while the larger particle size catholytes suffer significantly reduced capacity. Both LYBC and LIC catholytes provided capacity retention >80% after 200 cycles at 0.5C. These results imply that cathode particle size is critically important for performance at high CAM loading. Furthermore, both electrolyte and cathode were tape cast to scale up size and prepare realistic layer thicknesses. A small amount of binder was used in both layers, to balance the electrochemical performance and mechanical properties. Further, the discharge capacity of a tape cell was 152mA h/g at 0.1C with a capacity retention of 81.8% after 20 cycles at 0.5C. The results demonstrate the excellent performance of LYBC as an electrolyte, and provide guidance for halide-based cathode design.

25 ENERGY STORAGE↗
DOE OSTI2020

First-principles Modeling and Design of Solid-State Interfaces for the Protection and Use of Lithium Metal Anodes

Li-ion batteries are one of the most advanced energy storage technologies in use today. Li-ion batteries are used in a multitude of applications ranging from consumer electronics, medical devices, sensors and grid storage. However, improving the capacity and energy density delivered by current Li-ion technology requires advanced materials research into novel chemical systems. In this project we have focused particularly in the use of solid-state electrolytes with lithium metal electrodes. Research into all solid-state batteries (ASSB) with Li metal electrodes has significantly expanded in recent years, however most studies reported experimental findings, which left substantial room for theoretical and modeling work as a tool to understand and determine design principles allowing reliable and safe use of ASSBs with Li metal. Among the remaining obstacles preventing reliable use of ASSBs with a Li metal electrode, the stability of the interface between the solid electrolyte and Li metal, and the propagation/dendrite formation of Li metal and resulting mechanical degradation of the electrolyte are key phenomenon that are yet to be fully understood. In the current project we have addressed these two coupled phenomena using first principles calculations and mesoscale continuum modeling. We have obtained chemical and electrochemical stability windows for several solid electrolyte materials. Additionally, from mathematical and numerical modeling of Li protrusion and dendrite initiation during plating and stripping we have determined design criteria in terms of chemical, electrochemical, and mechanical properties and operating conditions for which stable deposition can occur. We also considered the effects of mixed electronic-ionic conduction in solid electrolytes, which has more recently been suggested as another important mechanism involved in ASSB failure. Throughout our work we have successfully addressed important questions necessary for the use of ASSB’s. We have determined guiding principles for materials properties and operating conditions necessary to operate ASSB’s. And have proposed novel solid electrolyte materials with predicted chemical stability an ionic conductivity. Although this represents significant progress in our understanding, open questions remain in order to fully develop reliable and safely operate ASSBs with Li metal. Future work, building on this project will require further experimental, theoretical and simulation efforts to address remaining questions.

25 ENERGY STORAGE↗
DOE OSTI2023

A free-standing lithium phosphorus oxynitride thin film electrolyte promotes uniformly dense lithium metal deposition with no external pressure

Lithium phosphorus oxynitride (LiPON) is an amorphous solid electrolyte that has been extensively studied over the last three decades. Despite the promise of pairing it with various electrode materials, LiPON’s rigidity and air sensitivity set limitations to understanding its intrinsic properties. We report a methodology to synthesize LiPON in a free-standing form that manifests remarkable flexibility and a Young’s modulus of ∼33 GPa. We use solid-state nuclear magnetic resonance and differential scanning calorimetry to quantitatively reveal the chemistry of the Li/LiPON interface and the presence of a well-defined LiPON glass-transition temperature of 207 °C. Combining interfacial stress and a gold seeding layer, our free-standing LiPON shows a uniformly dense deposition of lithium metal without the aid of external pressure. This free-standing LiPON film offers opportunities to study fundamental properties of LiPON for interface engineering for solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Paving Pathways Toward Long–Life Graphite/LiNi 0.5 Mn 1.5 O 4 Full Cells: Electrochemical and Interphasial Points of View

The high-voltage spinel cathode LiNi 0.5 Mn 1.5 O 4 (LNMO) with no cobalt and low nickel content is promising for lithium-ion batteries due to its high energy and power densities, good thermal stability, and low cost. However, its high operating voltage (≈4.7 V) results in a decomposition of the electrolyte, severe chemical crossover, and deterioration of electrode-electrolyte interphases (EEIs), hindering its practical viability. It is demonstrated here that by electrochemically pre-cycling the graphite in an electrolyte containing 30 wt.% fluoroethylene carbonate, a robust LiF-rich artificial solid electrolyte interphase can be constructed for surface protection; on the other hand, an electrochemical pre-lithiation of Fe-doped LNMO serves as a lithium source for graphite at a full-cell voltage of 2.6 V. As a result, the full cells with the as-modified electrodes deliver a high capacity of 129 mA h g –1 with an excellent capacity retention of 93% after 200 cycles, vastly outperforming the full cells with fresh electrodes (120 mA h g –1 initial capacity with 78% retention). Lastly, pathways toward long-life graphite||LNMO full cells are pictured based on the inspirations from the electrochemical modifications and in-depth analyses of the EEIs in this study.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A Carboranyl Electrolyte Enabling Highly Reversible Sodium Metal Anodes via a “Fluorine-Free” SEI

Realization of practical sodium metal batteries (SMBs) is hindered due to lack of compatible electrolyte components, dendrite propagation, and poor understanding of anodic interphasial chemistries. Chemically robust liquid electrolytes that facilitate both favorable sodium metal deposition and a stable solid-electrolyte interphase (SEI) are ideal to enable sodium metal and anode-free cells. Herein we present advanced characterization of a novel fluorine-free electrolyte utilizing the [HCB 11 H 11 ] 1- anion. Symmetrical Na cells operated with this electrolyte exhibit a remarkably low overpotential of 0.032 V at a current density of 2.0 mA cm -2 and a high coulombic efficiency of 99.5 % in half-cell configurations. Additionally, surface characterization of electrodes post-operation reveals the absence of dendritic sodium nucleation and a surprisingly stable fluorine-free SEI. Furthermore, weak ion-pairing is identified as key towards the successful development of fluorine-free sodium electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Irreparable Interphase Chemistry Degradation Induced by Temperature Pulse in Lithium–Ion Batteries

While it is widely recognized that the operating temperature significantly affects the energy density and cycle life of lithium-ion batteries, the consequence of electrode-electrolyte interphase chemistry to sudden environmental temperature changes remains inadequately understood. Here, we systematically investigate the effects of a temperature pulse (T pulse) on the electrochemical performance of LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) pouch full cells. By utilizing advanced characterization tools, such as time-of-flight secondary-ion mass spectrometry, we reveal that the T pulse can lead to an irreversible degradation of cathode-electrolyte interphase chemistry and architecture. Despite negligible immediate impacts on the solid-electrolyte interphase (SEI) on graphite anode, aggregated cathode-to-anode chemical crossover gradually degrades the SEI by catalyzing electrolyte reduction decomposition and inducing metallic dead Li formation because of insufficient cathode passivation after the T pulse. Consequently, pouch cells subjected to the T pulse show an inferior cycle stability to those free of the T pulse. Furthermore, this work unveils the effects of sudden temperature changes on the interphase chemistry and cell performance, emphasizing the importance of a proper temperature management in assessing performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Impact of Lithium‐Free Borate Additives on the Cycle Life and Calendar Aging of Silicon‐Based Lithium‐Ion Batteries

Silicon-anode lithium-ion batteries (LIBs) suffer from limited cycle life and poor calendar life, constraining their large-scale commercialization. Integrating additives into electrolytes is a simple and cost-effective strategy to improve these aspects. The effects of lithium-free boron-based additives on cycling and calendar performance of high-loading Si-anode LIBs remain largely unexplored. In this work, the influence of five Li-free borate additives, each with distinct molecular structures and elemental compositions, is systematically investigated. All additives enhance cycle life to varying extents. Notably, the addition of 1 v/v% tri(2,2,2-trifluoroethyl) borate to the baseline electrolyte nearly doubles the cycle life at 50% state of health. This enhancement is attributed to three key factors. Specifically, borate additives 1) improve electrochemical activity, 2) act as anion receptors that interact with [PF6]- anions and carbonate solvents to reduce electrolyte decomposition, and 3) promote the formation of a stable and polymeric solid electrolyte interphase layer. Furthermore, these additives exhibited negligible impact in mitigating leakage current during a 180 h voltage-hold calendar-aging test, indicating their limited effect in calendar life. These findings provide insight into the role of Li-free borate additives in improving cycle life while addressing the knowledge gap regarding their influence on calendar aging.

Li, Defu↗
DOE OSTI2025

Electrolyte-driven interphase stabilization in high-voltage sodium-ion full cells

Sodium-ion batteries with a high-voltage O3-type layered oxide cathode paired with a hard carbon anode can offer high energy density; however, significant interfacial instabilities driven by electrode/electrolyte reactions limit a broader industrial adoption. Localized high concentration electrolytes (LHCEs) are a rational choice as they promote salt decomposition over solvent, forming stable, inorganic-rich electrode-electrolyte interphases (EEIs). We present here a comparison of high-voltage (4.2 V) hard carbon | NaNi 1/3 Fe 1/3 Mn 1/3 O 2 pouch cells in LHCEs and in a standard carbonate-based electrolyte by (i) examining the influence of diluent choice on the electrochemical performance of LHCEs and (ii) investigating how the electrolyte chemistry affects the composition and structure of EEIs formed. Importantly, LHCEs demonstrate superior electrochemical performance, achieving 37% higher capacity after 200 cycles (119 vs. 87 mA h g -1 ) compared to the carbonate-based electrolyte. The enhanced stabilization provided by LHCEs at the interface with high-voltage sodium layered oxide cathode is revealed by gas evolution measurements obtained through online electrochemical mass spectrometry (OEMS). Time-of-flight secondary ion mass spectrometry paired with focused ion beam and advanced statistical analyses reveal that the superior performance of LHCE stems from a robust, thin cathode electrolyte interphase formed on the sodium layered oxide cathode and a homogeneous solid electrolyte interphase formation on the hard carbon anode. Furthermore, this study highlights the critical importance of electrolyte design in interphase stabilization, which plays a key role in advancing sodium-ion batteries toward commercial viability.

25 ENERGY STORAGE↗
DOE OSTI2025

Analysis of Degradation and Electrochemical Behavior of Lithium–Oxygen Batteries under Lean Electrolyte Conditions

Lithium-oxygen batteries have garnered much attention in the past decades due to their high energy density and active material abundancy. Decreasing the electrolyte volume is critical to achieving a high energy density for practical applications. Recent works have demonstrated a serious performance limitation at lower electrolyte fillings. Here, in this work, we study specifically the difference between flooded and lean electrolyte lithium-oxygen batteries by systematically tracing the source of performance degradation. We find that the key contributor to the decrease in performance under lean electrolyte conditions stems from the lithium metal anode rather than the cathode. Solid electrolyte interphase (SEI) compositionally appears to be the same from X-ray photoelectron spectroscopy but the coverage is less uniform, and impedance is much higher under lean electrolyte conditions. Such an effect likely produced the observed poorer cycle performance at 10 μL cm -2 (similar to 28% cathode's pore volume filled) vs 100 μL cm -2 (278% of cathode's pore volume) at a capacity of 1.0 mAh cm -2 (0.1 mAh cm -2 ) using an electrolyte composition of 1 M LiTFSI in TEGDME.

Córdoba, Daniel [Argonne National Laboratory (ANL)↗
DOE OSTI2026

High-Voltage Sodium–Metal Batteries with Asymmetric Fluoroalkoxylated Organoborate Anion Chemistry

The high reactivity of sodium (Na) metal restricts its compatibility to ether-based electrolytes, while the poor oxidative stability of ethers precludes their coupling to high-voltage cathodes, fundamentally limiting the operating voltage and energy density of sodium–metal batteries (SMBs). We present here a coordination-asymmetry strategy to reconcile this thermodynamic mismatch by generating in situ an asymmetric fluoroalkoxylated organoborate anion, [FB(OCH(CF 3 ) 2 ) 3 ] − (BOF – ), via a Lewis acid–base adduct reaction in ether electrolyte. The asymmetric ligand architecture differentiates oxidative and fluorination pathways: oxidizable B–O moieties mediate controlled interfacial reconstruction, whereas the terminal B–F units supply fluorine for chemical passivation. This self-adaptive chemistry yields nanoscale, conformal, compositionally graded interphases: a boron-oxide/boron-oxycarbide-rich cathode-electrolyte interphase (CEI) that mitigates ether oxidation and a bilayered inorganic–organic solid–electrolyte interphase (SEI) that regulates Na deposition. The nanostructured interphases enable highly reversible Na plating/stripping with an average Coulombic efficiency (CE) of 99.98% and sustain stable 4.3 V operation of anode-free SMBs in oxidation-prone ether electrolytes. Furthermore, this work establishes asymmetric boron coordination as a molecular-level design principle for creating chemically adaptive interphases that overcome the redox asymmetry in energy-dense electrochemical systems.

Anions↗
DOE OSTI2025

Investigating the effect of heterogeneities across the electrode|multiphase polymer electrolyte interfaces in high-potential lithium batteries

Polymer electrolytes hold great promise for safe and high-energy batteries comprising solid or semi-solid electrolytes. Multiphase polymer electrolytes, consisting of mobile and rigid phases, exhibit fast ion conduction and desired mechanical properties. However, fundamental challenges exist in understanding and regulating interactions at the electrode|electrolyte interface, especially when using high-potential layered oxide active materials at the positive electrode. Here we demonstrate that depletion of the mobile conductive phase at the interface contributes to battery performance degradation. Molecular ionic composite electrolytes, composed of a rigid-rod ionic polymer with nanometric mobile cations and anions, serve as a multiphase platform to investigate the evolution of ion conductive domains at the interface. Chemical and structural characterizations enable the visualization of concentration heterogeneity and spatially resolve the interfacial chemical states over a statistically significant field of view for buried interfaces. We report that concentration and chemical heterogeneities prevail at electrode|electrolyte interfaces, leading to phase separation in polymer electrolytes. In conclusion, understanding the hidden roles of interfacial chemomechanics in polymer electrolytes enables us to design an interphase tailoring strategy based on electrolyte additives to mitigate the interfacial heterogeneity and improve battery performance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modeling the electrical double layer at solid-state electrochemical interfaces

Models of the electrical double layer (EDL) at electrode/liquid-electrolyte interfaces no longer hold for all-solid-state electrochemistry. Here we show a more general model for the EDL at a solid-state electrochemical interface based on the Poisson–Fermi–Dirac equation. By combining this model with density functional theory predictions, the interconnected electronic and ionic degrees of freedom in all-solid-state batteries, including the electronic band bending and defect concentration variation in the space-charge layer, are captured self-consistently. Along with a general mathematical solution, the EDL structure is presented in various materials that are thermodynamically stable in contact with a lithium metal anode: the solid electrolyte Li 7 La 3 Zr 2 O 12 (LLZO) and the solid interlayer materials LiF, Li 2 O and Li 2 CO 3 . Here, the model further allows design of the optimum interlayer thicknesses to minimize the electrostatic barrier for lithium ion transport at relevant solid-state battery interfaces.

25 ENERGY STORAGE↗
DOE OSTI2022

Deep eutectic solvent-based polymer electrolyte for solid-state lithium metal batteries

Poly(ethylene) oxide (PEO)-based electrolytes have been widely studied for solid-state lithium batteries while their ionic conductivity and lithium-ion transference number still need to be further improved. Herein, using the combined experimental and theoretical approach, we demonstrate a novel, solid-state PEO-deep eutectic solvent (DES) electrolyte for the first time. We found that the in situ formation of DES can reduce the crystallinity of PEO matrix and more Li + ions can move freely owing to the weakened coordination between ether oxygens and Li-ions. Besides, we show that more Li + ions can be dissociated from Li salts in PEO-DES electrolyte using the molecular dynamics simulations. Such liquid-free PEO-DES electrolytes showed good ionic conductivity (2.1 × 10 −4 S cm −1 ) which is 160% higher than that of conventional PEO-LiTFSI (8.1 × 10 −5 S cm −1 ) electrolyte at 60 °C. Additionally, the PEO-DES electrolyte showed 136% increase of Li-ion transference number (0.33) compared with ionic liquid-doped PEO-LiTFSI (0.14) at 60 °C. Moreover, the PEO-DES exhibited good compatibility with Li metal and stable Li plating/stripping behavior with little morphology change of Li metal. In conclusion, this research also provides new insights into the enhancement mechanisms of novel polymer electrolytes, improving our fundamental understanding of critical challenges that have impeded the adoption of solid-state lithium metal batteries.

Deep eutectic solvent↗
DOE OSTI2021

Dual-Solvent Li-Ion Solvation Enables High-Performance Li-Metal Batteries

Novel electrolyte designs to further enhance the lithium (Li) metal battery cyclability are highly desirable. Here, fluorinated 1,6-dimethoxyhexane (FDMH) is designed and synthesized as the solvent molecule to promote electrolyte stability with its prolonged –CF 2 – backbone. Meanwhile, 1,2-dimethoxyethane is used as a co-solvent to enable higher ionic conductivity and much reduced interfacial resistance. Combining the dual-solvent system with 1 m lithium bis(fluorosulfonyl)imide (LiFSI), high Li-metal Coulombic efficiency (99.5%) and oxidative stability (6 V) are achieved. Using this electrolyte, 20 µm Li||NMC batteries are able to retain ≈80% capacity after 250 cycles and Cu||NMC anode-free pouch cells last 120 cycles with 75% capacity retention under ≈2.1 µL mAh -1 lean electrolyte conditions. Such high performances are attributed to the anion-derived solid-electrolyte interphase, originating from the coordination of Li-ions to the highly stable FDMH and multiple anions in their solvation environments. This work demonstrates a new electrolyte design strategy that enables high-performance Li-metal batteries with multisolvent Li-ion solvation with rationally optimized molecular structure and ratio.

25 ENERGY STORAGE↗
DOE OSTI2022

Co-intercalation-free ether electrolytes for graphitic anodes in lithium-ion batteries

Carbonate-based electrolytes are widely used in Li-ion batteries but are limited by a small operating temperature window and poor cycling with silicon-containing graphitic anodes. The lack of non-carbonate electrolyte alternatives such as ether-based electrolytes is due to undesired solvent co-intercalation that occurs with graphitic anodes. Here, we show that fluoroethers are the first class of ether solvents to intrinsically support reversible lithium-ion intercalation into graphite without solvent co-intercalation at conventional salt concentrations. In full cells using a graphite anode, they enable 10-fold higher energy densities compared to conventional ethers, and better thermal stability over carbonate electrolytes (operation up to 60 °C) by producing a robust solvent-derived solid electrolyte interphase (SEI). As single-solvent–single-salt electrolytes, they remarkably outperform carbonate electrolytes with fluoroethylene carbonate (FEC) and vinylene carbonate (VC) additives when cycled with graphite–silicon composite anodes. In conclusion, our molecular design strategy opens a new class of electrolytes that can enable next generation Li-ion batteries with higher energy density and a wider working temperature window.

25 ENERGY STORAGE↗
DOE OSTI2021

Effects of fluorinated solvents on electrolyte solvation structures and electrode/electrolyte interphases for lithium metal batteries

Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next generation high-density energy storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structure. Types of fluorinated co-solvents used in LHCEs are investigated here in searching for the most suitable diluent for high concentration electrolytes (HCEs). Non-solvating solvents (including fluorinated ethers, fluorinated borate and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through co-participation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery-performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.

Cao, Xia↗
NASA NTRS2003

Alternative Electrochemical Systems for Ozonation of Water

Electrochemical systems that are especially well suited for the small-scale generation of ozone and ozonated water for local use have been invented. These systems can operate with very little maintenance, and the only inputs needed during operation are electric power and water. Ozonated water produced by these systems can be used in diverse industrial applications: A few examples include sterilization in the brewing industry, general disinfection, and treatment of sewage and recycled water. The basic principle of operation admits of several alternative system configurations. The heart of the system is a stack of electrolytic cells, each containing a proton-exchange membrane (which serves as a solid electrolyte) sandwiched between a catalytic anode and a catalytic cathode. Preferably, the proton-exchange membrane is made of a perfluorinated sulfonic acid polymer. During electrolysis, a mixture of O2 and O3 gases is generated at the anode and H2 is generated at the cathode. Some of the O3 generated at the anode becomes dissolved in the water. The proportion of O3 in the O2/O3 mixture can be maximized by the selection of suitable electrode materials and the use of a high overpotential. Although the proton-exchange membrane conducts protons, it does not conduct electrons. It is also impermeable by gases; consequently, it maintains separation between the O2/O3 mixture evolved at the anode and the H2 evolved at the cathode.

Andrews, Craig C.↗