SEARCH · Engineering Papers

Results for “Transducers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 991 records · Page 55

All sources NASA NTRS DOE OSTI

NASA NTRS1991

RSRM-11 (36OW011) ballistics mass properties (STS-35)

The propulsion performance and reconstructed mass properties data from Thiolol's RSRM-11 motors which were assigned to the STS-35 launch are contained. The Thiokol manufacturing designations for the motors were 360W011A/360W011B, which are referred to as RSRM-11A and RSRM-B, respectively. The launch of STS-35 occurred on 2 December 1990 at the Eastern Test Range (ETR). The data contained herein was input to the STS-35 Flight Evaluation Report. The SRM propellant, TP-H1148, is a composite type solid propellants, formulated of polybutediene acrylic acid, acryonitrile terpolymer binder, epoxy curing agent, ammonium perchlorate oxidizer, and aluminum powder fuel. A small amount of burning rate catalyst (iron oxide) was added to achieve the desired propellant burn rate. The propellant evaluation and raw material information for the RSRM-11 are included. The ballistic performance presented was based on the Operational Flight Instrumentation (OFI) 12.5 sample per second pressure data for the steady state and tail off portion of the pressure trace. Recent studies have shown that the transducers are affected by the measuring system at KSC and temperature gradients created by the igniter heaters. Therefore, an adjustment to the data from each transducer is made to make the initial reading match the atmospheric pressure at the time of launch.

Hutchinson, B. J.↗

NASA NTRS1991

Micromachined silicon tunnel sensor for motion detection

The extreme sensitivity of electron tunneling to variations in electrode separation has been used to construct a novel, compact displacement transducer. Electrostatic forces are used to control the separation between the tunneling electrodes, thereby eliminating the need for piezoelectric actuators. The entire structure is composed of micromachined silicon single crystals, including a folded cantilever spring and a tip. Measurements of displacement sensitivity and noise are reported. This device offers a substantial improvement over conventional technology for applications which require compact, highly sensitive transducers.

Kenny, T. W.↗

NASA NTRS1990

NASA/Army rotor system flight research leading to the UH-60 airloads program

A review is presented of some of the early rotor systems flight research leading to the present comprehensive NASA/Army rotor system airloads program with the UH-60 helicopter. The experimental and analytical plans and progress for this program are described, including the design and development of a rotor blade which incorporated 242 pressure transducers buried in the surface of the blade, and also the development of calibration hardware for regular calibration and testing of the transducers. Supporting analytical developments based on the comprehensive analytical model of rotorcraft aerodynamics and dynamics (CAMRAD) and various CFD codes are discussed. The highly instrumented UH-60 as well as companion programs of full-scale and model wind tunnel tests of the UH-60 rotor with identical instrumentation will provide the opportunity to explore a full range of rotor experiments and the data necessary to validate the advanced methodologies under development.

Snyder, W. J.↗

NASA NTRS1990

Improved operation of magnetic bearings for flywheel energy storage system

Analysis and operation of prototype 500-Wh flywheel at low speeds have shown that many factors affect the correct functioning of the magnetic bearings. An examination is made of a number of these, including magnetic bearing control system nonlinearities and displacement transducer positioning, and their effects upon the successful operation of the suspension system. It is observed that the bearing control system is extremely sensitive to actuator parameters such as coil inductance. As a consequence of the analysis of bearing relaxation oscillations, the bearing actuator design methodology which has previously been used, where coil parameter selection is based upon static considerations, has been revised. Displacement transducer sensors which overcome the collocation problem are discussed.

Zmood, R. B.↗

NASA NTRS1990

Update on results of SPRE testing at NASA

The space power research engine (SPRE I), a free-piston Stirling engine with a linear alternator, was tested as a candidate for high-capacity space power. A portion of the test data from the SPRE I, essentially in its baseline configuration while operating with helium at heat exchanger metal temperature ratios ranging from 1.6 to 2.4 and mean cycle pressures of 7.5 and 15.0 Mpa, are presented. HFAST computer code predictions are presented for comparison. The measured results at 7.5 and 15 MPa, from the first day, from the first day of testing, at temperature ratios from 1.6 to 2.0 agreed fairly well with the HFAST code predictions; within -8.8 percent to +11.9 percent for PV power and -2.7 to +1.07 percentage points for PV efficiency. Measured compression-space pressure amplitude was 5.1 to 11.1 percent below predictions; although these results were within the error bands, there was poorer agreement than observed for previous tests, and the transducer calibration is suspect. All of the dynamic pressure transducer calibrations will be verified before testing is resumed. Measured pressure phase angles were within -1.95 percent to +5.37 percent of the predictions, which is much closer than previously observed. The poor agreement of the measured heat flow to the heater with the code appears to be due to thermocouple degradation.

Cairelli, James E.↗

NASA NTRS1992

Deformable Composite/Honeycomb Telescope Mirror

Piezoelectric transducers bonded to rear face sheet of honeycomb panel support spherical reflecting surface. Voltages applied to transducers compensate for distortions of reflecting surface.

Kuo, Chin-Po↗

NASA NTRS1991

Unsteady blade pressures on a propfan at takeoff: Euler analysis and flight data

The unsteady blade pressures due to the operation of the propfan at an angle to the direction of the mean flow are obtained by solving the unsteady three dimensional Euler equations. The configuration considered is the eight bladed SR7L propfan at takeoff conditions and the inflow angles considered are 6.3 deg, 8.3 deg, 11.3 deg. The predicted blade pressure waveforms are compared with inflight measurements. At the inboard radial station (r/R = 0.68) the phase of the predicted waveforms show reasonable agreement with the measurements while the amplitudes are over predicted in the leading edge region of the blade. At the outboard radial station (r/R = 0.95), the predicted amplitudes of the waveforms on the pressure surface are in good agreement with flight data for all inflow angles. The measured (installed propfan) waveforms show a relative phase lag compared to the computed (propfan alone) waveforms. The phase lag depends on the axial location of the transducer and the surface of the blade. On the suction surface, in addition to the relative phase lag, the measurements show distortion (widening and steepening) of the waveforms. The extent of distortion increases with increase in inflow angle. This distortion seems to be due to viscous separation effects which depend on the azimuthal location of the blade and the axial location of the transducer.

Nallasamy, M.↗

NASA NTRS1992

Acoustophoresis method and apparatus

A method and apparatus are provided for acoustophoresis, i.e., the separation of species via acoustic waves. An ultrasonic transducer applies an acoustic wave to one end of a sample container containing at least two species having different acoustic absorptions. The wave has a frequency tuned to or harmonized with the point of resonance of the species to be separated. This wave caused the species to be driven to an opposite end of the sample container for removal. A second ultrasonic transducer may be provided to apply a second, oppositely directed acoustic wave to prevent undesired streaming. In addition, a radio frequency tuned to the mechanical resonance and coupled with a magnetic field can serve to identify a species in a medium comprising species with similar absorption coefficients, whereby an acoustic wave having a frequency corresponding to this gyrational rate can then be applied to sweep the identified species to one end of the container for removal.

Heyman, Joseph S.↗

NASA NTRS1992

Unsteady blade pressures on a propfan at takeoff - Euler analysis and flight data

The unsteady blade pressures due to the operation of the propfan at an angle to the direction of the mean flow are obtained by solving the unsteady three dimensional Euler equations. The configurations considered is the eight bladed SR7L propfan at takeoff conditions and the inflow angles considered are 6.3 deg, 8.3 deg, 11.3 deg. The predicted blade pressure waveforms are compared with inflight measurements. At the inboard radial station (r/R = 0.68) the phase of the predicted waveforms show reasonable agreement with the measurements while the amplitudes are over predicted in the leading edge region of the blade. At the outboard radial station (r/R = 0.95), the predicted amplitudes of the waveforms on the pressure surface are in good agreement with flight data for all inflow angles. The measured (installed propfan) waveforms show a relative phase lag compared to the computed (propfan alone) waveforms. The phase lag depends on the axial location of the transducer and the surface of the blade. On the suction surface, in addition to the relative phase lag, the measurements show distortion (widening and steepening) of the waveforms. The extend of distortion increases with increase in inflow angle. This distortion seems to be due to viscous separation effects which depend on the azimuthal location of the blade and the axial location of the transducer.

Nallasamy, M.↗

NASA NTRS1991

Active vibration isolation using smart structures

Passive technologies for the isolation of structures from vibrating sources are often inadequate. Using active control inputs applied directly to the source or designing a structure integrating the transducers required for the control inputs and the response measurements are ways of dealing with the problem. Results are given which were obtained on an experimental set up simulating this kind of problem where the form and the position of the transducers could be varied. By measuring the response of the structure integrated over a particular area the effects of particular types of modes could be taken into account to deal with specific types of input or limit particular modes of response more efficiently. Results of using different modes of vibration excitation of the receiving structure with and without control are presented for particular input frequencies. The problems of optimizing the control system to deal with multiple frequency inputs are discussed.

Guigou, C.↗

NASA NTRS1993

Algorithm For Finer Resolution Of Position Of Shock

Algorithm computes streamwise position of terminal aerodynamic shock in inlet of engine of supersonic airplane. Signal representative of position of shock must be available to propulsion-control system of airplane to ensure proper operation of inlet. Algorithm computes position of shock with resolution much finer than spacing between transducers and requires neither increase in number of transducers nor other changes in pressure-measuring equipment.

Sajben, Miklos↗

NASA NTRS1993

Active Suppression Of Vibrations On Elastic Beams

Pairs of colocated piezoelectric transducers, independently controlled by multichannel adaptive controller, employed as actuators and sensors to achieve simultaneous attenuation of both extensional and flexural motion. Single pair used to provide simultaneous control of flexural and extensional waves, or two pairs used to control torsional motion also. Capability due to nature of piezoelectric transducers, when bonded to surfaces of structures and activated by oscillating voltages, generate corresponding oscillating distributions of stresses in structures. Phases and amplitudes of actuator voltages adjusted by controller to impede flow of vibrational energy simultaneously, in waves of various forms, beyond locations of actuators. Concept applies equally to harmonic or random response of structure and to multiple responses of structure to transverse bending, torsion, and compression within structural element. System has potential for many situations in which predominant vibration transmission path through framelike structure.

Silcox, Richard J.↗

NASA NTRS1993

Micromachined Tunneling Accelerometer

Separation of tunneling electrodes adjusted by varying electrostatic force. Major components of tunneling transducer formed on two silicon chips by microfabrication techniques. Use of electrostatic deflection reduces sensitivity of transducer to thermal drift and simplifies design. Sensitivity suitable for applications in which larger acceleration-sensing instruments required.

Kenny, Thomas W.↗

NASA NTRS1991

Automated eddy current analysis of materials

The use of eddy current techniques for characterizing flaws in graphite-based filament-wound cylindrical structures is described. A major emphasis was also placed upon incorporating artificial intelligence techniques into the signal analysis portion of the inspection process. Developing an eddy current scanning system using a commercial robot for inspecting graphite structures (and others) was a goal in the overall concept and is essential for the final implementation for the expert systems interpretation. Manual scans, as performed in the preliminary work here, do not provide sufficiently reproducible eddy current signatures to be easily built into a real time expert system. The expert systems approach to eddy current signal analysis requires that a suitable knowledge base exist in which correct decisions as to the nature of a flaw can be performed. A robotic workcell using eddy current transducers for the inspection of carbon filament materials with improved sensitivity was developed. Improved coupling efficiencies achieved with the E-probes and horseshoe probes are exceptional for graphite fibers. The eddy current supervisory system and expert system was partially developed on a MacIvory system. Continued utilization of finite element models for predetermining eddy current signals was shown to be useful in this work, both for understanding how electromagnetic fields interact with graphite fibers, and also for use in determining how to develop the knowledge base. Sufficient data was taken to indicate that the E-probe and the horseshoe probe can be useful eddy current transducers for inspecting graphite fiber components. The lacking component at this time is a large enough probe to have sensitivity in both the far and near field of a thick graphite epoxy component.

Workman, Gary L.↗

NASA NTRS1992

Acoustic device and method for measuring gas densities

Density measurements can be made in a gas contained in a flow through enclosure by measuring the sound pressure level at a receiver or microphone located near a dipole sound source which is driven at constant velocity amplitude at low frequencies. Analytical results, which are provided in terms of geometrical parameters, wave numbers, and sound source type for systems of this invention, agree well with published data. The relatively simple designs feature a transmitter transducer at the closed end of a small tube and a receiver transducer on the circumference of the small tube located a small distance away from the transmitter. The transmitter should be a dipole operated at low frequency with the kL value preferable less that about 0.3.

Shakkottai, Parthasarathy↗

NASA NTRS1993

Acoustophoresis separation method

A method and apparatus are provided for acoustophoresis, i.e., the separation of species via acoustic waves. An ultrasonic transducer applies an acoustic wave to one end of a sample container containing at least two species having different acoustic absorptions. The wave has a frequency tuned to or harmonized with the point of resonance of the species to be separated. This wave causes the species to be driven to an opposite end of the sample container for removal. A second ultrasonic transducer may be provided to apply a second, oppositely directed acoustic wave to prevent undesired streaming. In addition, a radio frequency tuned to the mechanical resonance and coupled with a magnetic field can serve to identify a species in a medium comprising species with similar absorption coefficients, whereby an acoustic wave having a frequency corresponding to this gyrational rate can then be applied to sweep the identified species to one end of the container for removal.

Heyman, Joseph S.↗

NASA NTRS1993

SUMS experiment flight results on STS-35

Calibrated pressure measurements for species with mass to charge ratios up to 50 amu/e(-) were obtained from the Shuttle Upper Atmosphere Mass Spectrometer (SUMS) experiment during reentry on the STS-35 mission. Data were collected from 180 km, when the signal rose above the background, to about 87 km, when the SUMS system automatically closed the gas inlet value. However, data above 115 km was contaminated from a source of gas emanating from pressure transducers connected in parallel to the mass spectrometer. At lower altitudes, the pressure transducer data is compared with the mass spectrometer total pressure with excellent agreement. The free-stream density in the rarefied flow flight regime is calculated using an orifice pressure coefficient model based upon direct simulation Monte Carlo results. This density, when compared with the 1976 U.S. standard atmosphere model, exhibits the wave-like nature seen on previous flights using accelerometry. In addition, selected spectra are presented at higher altitudes (320 km) showing the effects of the ingestion of gases from a forward fuselage fuel dump. An analysis of the spectra data from this event is presented to show that no significant permanent changes occurred which affected the data interpretation at lower altitudes. Further, the localized chemistry from the individual species during the onset of aerodynamic heating is examined to the extent possible for a closed source system, such as SUMS. Near the orifice entrance, a significant amount of CO2 was generated from chemical reactions with the carbon panels of the Orbiter and absorbed oxygen on the system tubing.

Blanchard, Robert C.↗

NASA NTRS1993

LOX/hydrocarbon rocket engine analytical design methodology development and validation. Volume 2: Appendices

This final report includes a discussion of the work accomplished during the period from Dec. 1988 through Nov. 1991. The objective of the program was to assemble existing performance and combustion stability models into a usable design methodology capable of designing and analyzing high-performance and stable LOX/hydrocarbon booster engines. The methodology was then used to design a validation engine. The capabilities and validity of the methodology were demonstrated using this engine in an extensive hot fire test program. The engine used LOX/RP-1 propellants and was tested over a range of mixture ratios, chamber pressures, and acoustic damping device configurations. This volume contains time domain and frequency domain stability plots which indicate the pressure perturbation amplitudes and frequencies from approximately 30 tests of a 50K thrust rocket engine using LOX/RP-1 propellants over a range of chamber pressures from 240 to 1750 psia with mixture ratios of from 1.2 to 7.5. The data is from test configurations which used both bitune and monotune acoustic cavities and from tests with no acoustic cavities. The engine had a length of 14 inches and a contraction ratio of 2.0 using a 7.68 inch diameter injector. The data was taken from both stable and unstable tests. All combustion instabilities were spontaneous in the first tangential mode. Although stability bombs were used and generated overpressures of approximately 20 percent, no tests were driven unstable by the bombs. The stability instrumentation included six high-frequency Kistler transducers in the combustion chamber, a high-frequency Kistler transducer in each propellant manifold, and tri-axial accelerometers. Performance data is presented, both characteristic velocity efficiencies and energy release efficiencies, for those tests of sufficient duration to record steady state values.

Niiya, Karen E.↗