Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ni”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Materials Data on Ni(N4O3)2 by Materials Project

Ni(N4O3)2 crystallizes in the cubic Fm-3m space group. The structure is three-dimensional and consists of four raney alloy molecules and one N4O3 framework. In the N4O3 framework, there are two inequivalent N1+ sites. In the first N1+ site, N1+ is bonded to six equivalent O2- atoms to form corner-sharing NO6 octahedra. The corner-sharing octahedral tilt angles are 0°. All N–O bond lengths are 1.96 Å. In the second N1+ site, N1+ is bonded in a distorted rectangular see-saw-like geometry to four equivalent O2- atoms. All N–O bond lengths are 1.96 Å. O2- is bonded to six N1+ atoms to form a mixture of edge and corner-sharing ON6 octahedra. The corner-sharing octahedra tilt angles range from 0–5°.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on Ni(PtO2)3 by Materials Project

NiPt3O6 crystallizes in the orthorhombic Pbam space group. The structure is three-dimensional. there are two inequivalent Pt+3.33+ sites. In the first Pt+3.33+ site, Pt+3.33+ is bonded in a square co-planar geometry to four O2- atoms. There is two shorter (1.97 Å) and two longer (1.98 Å) Pt–O bond length. In the second Pt+3.33+ site, Pt+3.33+ is bonded to six O2- atoms to form a mixture of edge and corner-sharing PtO6 octahedra. The corner-sharing octahedral tilt angles are 60°. There are a spread of Pt–O bond distances ranging from 2.03–2.09 Å. Ni2+ is bonded in a distorted body-centered cubic geometry to eight O2- atoms. There are a spread of Ni–O bond distances ranging from 2.17–2.50 Å. There are three inequivalent O2- sites. In the first O2- site, O2- is bonded to two equivalent Pt+3.33+ and two equivalent Ni2+ atoms to form ONi2Pt2 tetrahedra that share corners with ten ONi2Pt2 tetrahedra and edges with three ONiPt3 tetrahedra. In the second O2- site, O2- is bonded in a 4-coordinate geometry to three Pt+3.33+ and one Ni2+ atom. In the third O2- site, O2- is bonded to three Pt+3.33+ and one Ni2+ atom to form distorted ONiPt3 tetrahedra that share corners with eight ONiPt3 tetrahedra and edges with two equivalent ONi2Pt2 tetrahedra.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on Ni(NF2)2 by Materials Project

NiF4N2 is (La,Ba)CuO4 structured and crystallizes in the tetragonal I4/mmm space group. The structure is two-dimensional and consists of four ammonia molecules and two NiF4 sheets oriented in the (0, 0, 1) direction. In each NiF4 sheet, Ni2+ is bonded to six F1- atoms to form corner-sharing NiF6 octahedra. The corner-sharing octahedral tilt angles are 0°. There is two shorter (1.83 Å) and four longer (1.90 Å) Ni–F bond length. There are two inequivalent F1- sites. In the first F1- site, F1- is bonded in a linear geometry to two equivalent Ni2+ atoms. In the second F1- site, F1- is bonded in a single-bond geometry to one Ni2+ atom.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Improved Creep and Tensile Properties of a Corrosion Resistant Ni-Based Superalloy Using High Temperature Aging and Nb/Ta Additions

Resistance to creep deformation is essential for cast and wrought Ni-based superalloys in next generation energy systems due to the considerable exposure times required at the operating temperature. Here the amount of precipitate strengthening was increased in variants to Inconel alloy 725 (IN725), a corrosion resistant alloy, to improve its elevated temperature mechanical strength. Additions of Nb or Ta coupled with a high temperature aging (HTA) heat treatment promoted the formation of γ" precipitates and grain boundary phases which led to significant increases in time to failure. The HTA increased the creep life of various alloy formulations as compared to the standard aging heat treatment with a maximum improvement of 371%. The Nb and Ta additions lowered the minimum creep rate (MCR) and had a similar effect on increasing creep life. The positive effect of the additions was more pronounced when coupled with the HTA which employed a higher temperature in the first step of the heat treatment to promote precipitate phase formation. The Ti/Al ratio was used to design alloys with preferential formation of ' or γ" precipitates. Compact morphology precipitates were formed in the alloys with a low Ti/Al ratio. While a low Ti/Al ratio was primarily associated with lower MCRs, the effect on the creep life was less evident than that of the HTA. By using additions of Nb or Ta and a HTA heat treatment, the creep life of IN725 for testing at 973 K (700 °C) and 483 MPa was improved by up to 256%.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A creep-resistant additively manufactured Al-Ce-Ni-Mn alloy

Existing additively manufactured aluminum alloys exhibit poor creep resistance due to coarsening of their strengthening phases and refined grain structures. In this paper, we report on a novel additively manufactured Al-10.5Ce-3.1Ni-1.2Mn wt.% alloy which displays excellent creep resistance relative to cast high-temperature aluminum alloys at 300–400 °C. In this work, the creep resistance of this alloy is attributed to a high volume fraction (~35%) of submicron intermetallic strengthening phases which are coarsening-resistant for hundreds of hours at 350 °C. The results herein demonstrate that additive manufacturing provides opportunities for development of creep-resistant aluminum alloys that may be used in bulk form in the 250–400 °C temperature range. Pathways for further development of such alloys are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multiscale investigation of thermomechanical and compositional developments in Ni alloy 718 under laser processing

Laser processing has been widely employed in various applications due to its exceptional spatial resolution. However, the rapid temperature gradients generated in localized areas present significant challenges for experimental characterization using conventional instruments. To characterize Ni alloy 718 during laser processing, we employed in-situ synchrotron X-ray diffraction with a high-speed detector, a method particularly well-suited for probing processes with high temporal and spatial resolution. Through a series of in-situ experiments, we investigated the local variations in the evolution of microstructures and thermomechanical behaviors within a keyhole mode melt pool. The in situ macroscopic thermomechanical behaviors were quantified using an empirical model derived from diffraction patterns, with experimental results showing reasonable agreement with finite element analysis. Various laser parameters were tested to assess their influences on the residual strains in the melt pools. The results revealed that the residual strain in the keyhole mode melt pool is relatively insensitive to variations in the parameters and is smaller than that in the melt pool created under conduction mode laser scanning. Additionally, we analyzed the shapes of individual diffraction spots, providing insights into the plastic behaviors and compositional developments in the resolidified alloy. The analysis confirmed that compositional variations in a dendritic microstructure manifest as asymmetric broadening of the diffraction spots.

Ni alloy 718↗
DOE OSTI2020

Multi-scale microstructural investigation of a laser 3D printed Ni-based superalloy

The heterogeneous microstructure of a laser 3D printed Ni-based superalloy was examined at multiple length scales. The sub-millimeter-sized columnar crystal grains are composed of micron-sized cellular colonies. The crystal grains grow in epitaxy with the substrate under the large temperature gradient and high cooling rate. The cell boundaries, decorated with γ/γ' eutectics, μ-phase precipitates and high density of dislocations, show enrichment of γ' forming elements and low-angle misorientations. Dislocations trapped in the intra-cellular regions are characterized as statistically stored dislocations with no detectable contribution to lattice curvature, and are the results of the interaction between dislocations and γ' precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Partial oxidation of isobutylene using Ni TiO x

In this work, we report an aerobic partical oxidation of isobutylene into isoprene, acetone, and p-xylene using a mesoporous Ni TiO x catalytic material. In this work, two catalysts were found to synthesize two of these three valuable products with high selectivity, with p-xylene being synthesized with a selectivity of 46.0% and isoprene being synthesized with a selectivity of 64.7%, with overall conversions of isobutylene being 34.0% and 11.9% respectively. These reactions were done at relatively low temperatures. (300°C or below) and are conducted at flow rates of 10 sccm oxygen and isobutylene. The nickel titania catalysts were studied extensively using various characterization methodologies such as TEM, Raman, XRD, and XRF.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Towards synthetic L 1 0 -FeNi: Detecting the absence of cubic symmetry in Laser-Ablated Fe-Ni nanoparticles

The L 1 0 crystal structure underlines an important class of chemically ordered alloys that exhibits uniaxial magnetocrystalline anisotropy. The near-equiatomic L 1 0 -FeNi extracted from meteorites has demonstrated intriguing magnetic properties for permanent magnet applications. However, the synthesis of this chemically ordered non-cubic structure has been a longstanding challenge. Here, in this work, we demonstrate the absence of cubic symmetry in near-equiatomic Fe-Ni nanoparticles synthesized by picosecond-pulsed laser ablation in liquids. The non-cubic phase detected in these particles can only be L 1 0 -FeNi or hexagonal close-packed (HCP) FeNi, and the absence of cubic symmetry was unequivocal. The orientation relationship between the non-cubic phase and the adjacent cubic phase was characterized by a series of transmission electron microscopy (TEM) techniques, which consistently suggests that the formation of the non-cubic phase involves a martensitic transformation process.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High Temperature Oxidation Behavior of Ni-based High Entropy Superalloys

A new class of polycrystalline gamma-prime strengthened superalloys with alloy compositions of (wt%) Ni-20Co-13Cr-6Fe-4Al-3W-2Mo-(4-x)Nb-(x)Ti (x = 0,1,2) were subjected to cyclic oxidation exposures in dry air at 800 °C for 3600 h. The alloys were borderline chromia/alumina formers, showing good oxidation resistance relative to commercially available materials of similar composition. While all alloys formed alumina scales initially, only the alloy with the lowest Ti/Nb ratio retained an alumina scale for the duration of the exposure. Formation of a continuous layer of rutile TiO 2 at the alumina/alloy interface is proposed to cause eventual alumina failure for the alloys containing Ti.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elucidating the impact of stress states on grain boundary passivation in Ni-5Cr using the Rhines pack method

The oxidation behavior of a Ni–5Cr (at.%) alloy was evaluated at 420 ° C using the Rhines pack method and simultaneous tensile and compressive stress states via a miniature four-point bending fixture. At this moderate temperature, grain boundaries dominate mass transport and the resulting oxidation response. Oxidation produced approximately 1μ⁢m-wide protective Cr 2 O 3 films capping some grain boundaries and penetrative, intergranular Cr-rich oxides at other grain boundaries. Externally applied tensile and compressive stress during oxidation increased the prevalence of Cr 2 O 3 cap formation compared to no applied stress, with tensile stress resulting in more Cr 2 O 3 caps than compressive stress. The observed oxide cap morphology was similar across all test conditions. Regions under compressive stress showed an order of magnitude greater Cr depletion depth along the grain boundary. Chromium nitrides (CrN), likely from N contamination of the Rhines pack cell, were observed both at the oxide–metal interface and intergranularly within the alloy. Collectively these results demonstrate that applied stress promotes localized protective oxide cap formation over grain boundaries, with compressive stress additionally promoting deeper Cr depletion. Furthermore the experimental approach helped separate out the effects of stress on local oxide formation and grain boundary passivation.

4 point bend↗
DOE OSTI2021

Ni(OH) 2 -free NiCu as a hydrogen evolution and oxidation electrocatalyst

In this work, we investigate the role of the nickel surface oxidation and the use of additional reducing agent in the synthesis process in the electrochemical activity of NiCu electrocatalysts for hydrogen oxidation reaction and hydrogen evolution reaction. In addition, the role of the carbon support morphology is also investigated: two different supports, DENKA black and Ketjenblack with widely different properties (specific surface, proportion of low strain carbons, etc.) are studied, and no difference are observed in their electrochemical activity. However, the use 4-aminoantipyrine as a reducing agent resulted in a dramatic increase in non-oxidized Ni at the electrocatalyst’ surface, concomitant to a large increase in its activity for both the hydrogen evolution and oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Beneficial effect of copper on pitting resistance of Ni-Cr-Fe alloys

This study examines the effect of copper alloying on pitting resistance in a model solid solution FCC Ni-13%Cr-10%Fe alloy through potentiodynamic and potentiostatic polarization in 0.1 M NaCl in conjunction with an analysis using first-principles competitive electro-chemisorption modeling. The pitting potential increased with increasing Cu content in the alloy. Furthermore, the extent of metastable pit growth was suppressed and the incubation time for metastable to stable pit transition increased with Cu content. The first-principles competitive adsorption calculations suggested that Cu alloying suppresses chloride ion adsorption on the alloy surface in a simulated pit environment, which inhibits active dissolution at the pit bottom, enhances proton adsorption, and thereby increases the local pH at the pit bottom. In conclusion, we propose that these two effects of Cu in solid solution combine to reduce pit stability and may act in addition to the enrichment of Cu on the corroding pit surface.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Decoupling the degradation factors of Ni-rich NMC/Li metal batteries using concentrated electrolytes

Battery degradation results from multiple factors that usually correlate with each other. Electrochemical corrosion of the current collector is one of the main reasons for battery failure, leading to poor internal electrical contact and the dissolution of harmful ions into electrolytes. This phenomenon is especially evident in lithium bistrifluoromethanesulfonimidate (LiTFSI)-based electrolytes, although they have many advantages over conventional lithium hexafluorophosphate (LiPF 6 )-based electrolytes, such as low viscosity, good thermal stability, and stable to water. Recently, highly concentrated electrolytes are found hopeful of inhibiting aluminum's corrosion and boosting new electrolyte development. Here we discuss the solvation structures of liquid electrolytes and decouple the degradation mechanisms of using LiTFSI-based electrolytes in Li(Ni 0.8 Co 0.1 Mn 0.1 )O 2 /Li metal batteries. The results suggest although concentrated electrolytes inhibit the Al corrosion, the growth of lithium dendrites and the protection of the cathode-electrolyte interphase are not significantly improved. Furthermore, this paper provides a paradigm to evaluate the performance of electrolytes comprehensively.

25 ENERGY STORAGE↗
DOE OSTI2020

Design and development of a high-performance Ni-based superalloy WSU 150 for additive manufacturing

This work proposes a design and development strategy of a new nickel-based superalloy for additive manufacturing. A new Ni-based superalloy has been developed by the application of the combinatorial alloy development technique coupled with CALPHAD based solidification modeling by effectively suppressing the precipitation kinetics. The suppression of precipitation during processing paved a way for prevention of cracks during deposition. The new alloy "WSU 150" revealed excellent room temperature mechanical properties with a yield strength of 867 MPa, an ultimate tensile strength of 1188 MPa, and an elongation of 27.9% in the as-deposited condition. The mechanical properties of the heat-treated alloy were improved significantly to 1114 MPa yield strength, 1396 MPa ultimate tensile strength, and an elongation of 16.1%. Improvement in the mechanical properties is attributed to the additional precipitation and coarsening of γ' and carbides during heat-treatment. Microstructural investigation of the alloy revealed spherical γ' with a rippled size distribution from the center to the interdendritic region. The average size of the γ' particles in the as-deposited condition was found to be around 48 nm in the interdendritic region. Heat-treatment promoted the coarsening of γ' which is explained in the paper.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Constructing stable interface layer for boosting high-voltage cycling performance of single-crystal Ni-rich cathodes

Increasing demand for electric vehicles (EVs) worldwide and the requirements for environmental protection have greatly promoted the development of low-Co, Ni-rich layered cathodes due to their high energy density, reasonable cost, and less environmental pollution. Nevertheless, serious performance degradation and safety concerns resulting from structural/interfacial instability under high operating voltages (≥4.3 V) have greatly hindered its commercialization. Herein, we propose a feasible surface modification strategy by introducing a multifunctional Li 2 SiO 3 (LSO) coating layer onto the surface of Co less single-crystalline LiNi 0.63 Co 0.07 Mn 0.3 O 2 (NCM) to solve the above challenges. Additionally, the uniform Li 2 SiO 3 coating layer has a unique three-dimensional (3D) ion diffusion channel, which greatly promotes the transmission of Li + and alleviates interfacial stress accumulation. Equally important, the electrochemically inert Li 2 SiO 3 coating layer has a stable structure framework with strong Si-O bonds, which inhibit anisotropic particle volume expansion and the occurrence of side reactions during long-term cycling. As a consequence, LSO modified NCM exhibits greatly improved electrochemical properties even at harsh testing conditions and achieves capacity retention of 79.1% after 200 cycles at 25°C within 2.95-4.5 V in half cells. Furthermore, it provides an outstanding capacity retention of 94.7% after 300 cycles at 25°C within 2.95-4.4 V when tested in pouch full cells.

25 ENERGY STORAGE↗
DOE OSTI2023

Multiscale characterization of an additively manufactured property graded Ni-base alloy for molten-salts\supercritical-CO 2 heat exchangers

The sequential optimization of strength and corrosion resistance in conventional alloy design procedures often results in a tradeoff between environmental degradation and optimal mechanical properties. A concurrent optimization of these two material properties is essential to efficiently develop high temperature alloys that can withstand harsh environments increasingly required for carbon–neutral energy technologies. In this work, we demonstrate the feasibility of directed energy deposition (DED) to manufacture a dual-corrosion resistant Ni-based alloy (Hastelloy N and Haynes 282), that meets the high temperature operation requirements of a molten-salts\supercritical-CO 2 (sCO 2 ) heat exchanger. A combination of multiscale characterization techniques and computational thermodynamics was employed to evaluate the cracking susceptibilities during fabrication and predict the microstructural stability of the material. Very good agreement was achieved between the observed and predicted phases and phase fractions of the as-printed material. A careful characterization of the transition zone between the two terminal alloy chemistries revealed potential precipitation strengthening (γ') on the Hastelloy N side while columnar-shaped M 23 C 6 and γ' precipitates that formed at grain boundaries (GBs) of the transition zone likely minimized the local interfacial energies. Both these mechanisms are believed to increase the interfacial stability but their performance at high temperatures requires further investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the effect of elemental partitioning to secondary phases after solution and aging heat treatments in a Co-Ni-based superalloy

Here, this paper presents the phase stability and elemental partitioning in a Co-40Ni-10Al-7.5W-10Cr-3Nb-0.06B-0.6C (at.%) superalloy (referred to as 3Nb) after a two-step heat treatment. The resulting microstructure consisted of γ, γ', MC carbides and µ-Co 7 W 6 phase decorating the regions near and at the grain boundaries. Nb preferentially partitioned to the γ'-phase and other elements such as Ni, Cr and W were responsible for the μ-phase formation.

36 MATERIALS SCIENCE↗