Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Burn control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Conventional engine technology. Volume 3: Comparisons and future potential

The status of five conventional automobile engine technologies was assessed and the future potential for increasing fuel economy and reducing exhaust emission was discussed, using the 1980 EPA California emisions standards as a comparative basis. By 1986, the fuel economy of a uniform charge Otto engine with a three-way catalyst is expected to increase 10%, while vehicles with lean burn (fast burn) engines should show a 20% fuel economy increase. Although vehicles with stratified-charge engines and rotary engines are expected to improve, their fuel economy will remain inferior to the other engine types. When adequate NO emissions control methods are implemented to meet the EPA requirements, vehicles with prechamber diesel engines are expected to yield a fuel economy advantage of about 15%. While successful introduction of direct injection diesel engine technology will provide a fuel savings of 30 to 35%, the planned regulation of exhaust particulates could seriously hinder this technology, because it is expected that only the smallest diesel engine vehicles could meet the proposed particulate requirements.

Dowdy, M. W.↗

Progress report - Advanced cryogenic OTV engine technology

New technologies for space-based, reusable, throttleable, cryogenic orbit transfer propulsion are being evaluated. A variable-thrust (200 to 3000 lbF), 2000 psi chamber pressure, LO2/LH2 engine has been selected to demonstrate the 20-hour, 500-restart life goal, and a specific impulse in excess of 480 lbF-sec/lbM. The results of recent vehicle-engine integration analyses and the progress in design, fabrication, and testing are provided. Emphasis is placed on the following technology areas being investigated in support of the advanced engine design: LOX hydrostatic bearings; burn-resistant materials for high-pressure GOX turbines and valves; high surface-low flux annular combustion chambers for the dual propellant expander cycle; improved cooling approaches for high-pressure combustion chambers, new concepts in integrated controls; and engine health diagnostics.

Schoenman, L.↗

A Probabilistic System Analysis of Intelligent Propulsion System Technologies

NASA s Intelligent Propulsion System Technology (Propulsion 21) project focuses on developing adaptive technologies that will enable commercial gas turbine engines to produce fewer emissions and less noise while increasing reliability. It features adaptive technologies that have included active tip-clearance control for turbine and compressor, active combustion control, turbine aero-thermal and flow control, and enabling technologies such as sensors which are reliable at high operating temperatures and are minimally intrusive. A probabilistic system analysis is performed to evaluate the impact of these technologies on aircraft CO2 (directly proportional to fuel burn) and LTO (landing and takeoff) NO(x) reductions. A 300-passenger aircraft, with two 396-kN thrust (85,000-pound) engines is chosen for the study. The results show that NASA s Intelligent Propulsion System technologies have the potential to significantly reduce the CO2 and NO(x) emissions. The results are used to support informed decisionmaking on the development of the intelligent propulsion system technology portfolio for CO2 and NO(x) reductions.

Tong, Michael T.↗

Conceptual design of a pressure tube light water reactor with variable moderator control

This paper presents the development of innovative pressure tube light water reactor with variable moderator control. The core layout is derived from a CANDU line of reactors in general, and advanced ACR-1000 design in particular. It should be stressed however, that while some of the ACR-1000 mechanical design features are adopted, the core design basics of the reactor proposed here are completely different. First, the inter fuel channels spacing, surrounded by the calandria tank, contains a low pressure gas instead of heavy water moderator. Second, the fuel channel design features an additional/external tube (designated as moderator tube) connected to a separate moderator management system. The moderator management system is design to vary the moderator tube content from 'dry' (gas) to 'flooded' (light water filled). The dynamic variation of the moderator is a unique and very important feature of the proposed design. The moderator variation allows an implementation of the 'breed and burn' mode of operation. The 'breed and burn' mode of operation is implemented by keeping the moderator tube empty ('dry' filled with gas) during the breed part of the fuel depletion and subsequently introducing the moderator by 'flooding' the moderator tube for the 'burn' part. This paper assesses the conceptual feasibility of the proposed concept from a neutronics point of view. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Design of inertial fusion implosions reaching the burning plasma regime

One of the last remaining milestones in fusion research before reaching ignition is creating a burning plasma state, where alpha particles from deuterium-tritium (DT) fusion reactions redeposit their energy as the dominant source of heating in the plasma. The indirect-drive inertial confinement fusion approach at the National Ignition Facility (NIF) uses a laser-generated radiation cavity (hohlraum) to spherically implode DT fuel to high temperatures and densities in a central ”hot spot”. Here, we deliver more energy to the hot spot than ever before, while maintaining the extreme pressures required for inertial confinement, by increasing the size of the implosion compared to previous experiments. We develop more efficient hohlraums, to drive these larger implosions within NIF’s current laser energy and power capability and control symmetry by moving energy between laser beams and by changing the shape of the hohlraum. These designs resulted in record fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy. Radiation hydrodynamics simulations show alpha particle heating as the dominant term in the hot spot energy balance, e.g. a burning plasma state. This work is expected to motivate future studies of burning plasmas and improve predictive capability by providing a benchmark for modeling used to understand the proximity to ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Biomass Burning and Fossil Fuel Apportionment via Greenhouse Gas Enhancement Ratios Over Southeast Asia as Measured During ASIA-AQ

As Southeast Asian economies continue to grow, so will their contribution to global greenhouse gas (GHG) emissions, driven primarily by increases in fossil fuel combustion. Left unchecked, these emissions will negatively impact air quality and climate, therefore it is imperative that emission sources are properly identified and accounted for in emission inventories. Enhancement ratios of GHGs have been used to characterize regional emissions as either dominated by fossil fuel combustion or biomass burning. In particular, airborne assessment of short-term continuous emission ratios has proven useful to quantify relative contributions of fossil fuel and biomass burning to GHG emissions. The 2024 Airborne and Satellite Investigation of Asian Air Quality (ASIA-AQ) campaign, flying over the Philippines, Korea, Thailand, and Taiwan, sampled a variety of emissions including significant biomass burning, local urban pollution, and transport events. This work will explore the impact of GHG emissions on the distinctive pollution of the sampled locations. As airborne GHG measurements over Southeast Asia are scarce if not nonexistent, this work provides a crucial link between established ground-based measurements and state-of-the-art satellite observations such as those from South Korea’s Geostationary Environment Monitoring Spectrometer (GEMS). Analysis of GHG enhancement ratios in East Asia will lead to more accurate emission inventories which can be used to implement more effective GHG control measures leading to improved air quality and minimizing the effect on climate.

ASIA-AQ↗

Status of Graphite Oxidation Work

Data were developed to compare the extent of structural damage associated with high temperature exposure to an air leak. Two materials, NBG-18 graphite and unpurified PCEA graphite have been tested as of this report. The scope was limited to isothermal oxidation at a single temperature, 750°C. Ambient post-oxidation compression strength testing was performed for three levels of burn off (1%, 5%, and 10% mass loss) for two leak scenarios: 100% air and 10% air in helium. Temperature, gas flow, and dynamic mass loss oxidation conditions were monitored and recorded for each sample. The oxidation period was controlled with flow of inert gas during the thermal ramp and upon cool down with a constant 10 liter per minute flow maintained throughout furnace operation. Compressive strengths of parallel un-oxidized samples were tested to assess the relative mass loss effects. In addition to baseline samples matching the un-oxidized dimensions of the oxidized samples, two sets of mechanically reduced samples were prepared. One set was trimmed to achieve the desired mass loss by removing an effectively uniform depth from the geometric surface of the sample. The other set was cored to produce a full penetration axial hole down the center of each sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Integrated guidance, navigation and control verification plan primary flight system

The verification process and requirements for the ascent guidance interfaces and the ascent integrated guidance, navigation and control system for the space shuttle orbiter are defined as well as portions of supporting systems which directly interface with the system. The ascent phase of verification covers the normal and ATO ascent through the final OMS-2 circularization burn (all of OPS-1), the AOA ascent through the OMS-1 burn, and the RTLS ascent through ET separation (all of MM 601). In addition, OPS translation verification is defined. Verification trees and roadmaps are given.

Source record↗

Deposition of Na2SO4 from salt-seeded combustion gases of a high velocity burner rig

The mechanism of deposition of Na2SO4 was studied under controlled laboratory conditions and the results have been compared to a recently developed comprehensive theory of vapor deposition. Thus Na2SO4, NaCl, NaNO3 and simulated sea salt solutions were injected into the combustor of a nominal Mach 0.3 burner rig burning jet fuel at constant fuel/air ratios. The deposits formed on inert collectors, rotation in the cross flow of the combustion gases, were weighed and analyzed. Collector temperature was uniform and could be varied over a large range by internal air cooling. Deposition rates and dew point temperatures were determined. Supplemental testing included droplet size measurements of the atomized salt solutions. These tests along with thermodynamic and transport calculations were utilized in the interpretation of the deposition results.

Santoro, G. J.↗

Development of a Pulsed Combustion Actuator For High-Speed Flow Control

This paper describes the flow within a prototype actuator, energized by pulsed combustion or detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant chamber, and the products exit the device as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. The combustion chamber has been constructed with windows, and the flow inside it has been visualized using Planar Laser-Induced Fluorescence (PLIF). The pulsed jet at the exit of the device has been observed using schlieren.

Cutler, Andrew D.↗

Toward a High-Frequency Pulsed-Detonation Actuator

This paper describes the continued development of an actuator, energized by pulsed detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant tube and the products exit the tube as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. Pulsed detonations have been demonstrated in the lambda/4 mode of an 8 inch long tube at approximately 600 Hz. The pulsed jet at the exit of the device has been observed using shadowgraph and an infrared camera.

Cutler, Andrew D.↗

Toward a High-Frequency Pulsed-Detonation Actuator

This paper describes the continued development of an actuator, energized by pulsed detonations, that provides a pulsed jet suitable for flow control in high-speed applications. A high-speed valve, capable of delivering a pulsed stream of reactants a mixture of H2 and air at rates of up to 1500 pulses per second, has been constructed. The reactants burn in a resonant tube and the products exit the tube as a pulsed jet. High frequency pressure transducers have been used to monitor the pressure fluctuations in the device at various reactant injection frequencies, including both resonant and off-resonant conditions. Pulsed detonations have been demonstrated in the lambda/4 mode of an 8 inch long tube at approx. 600 Hz. The pulsed jet at the exit of the device has been observed using shadowgraph and an infrared camera.

Cutler, Andrew D.↗

Processing and Characterization of Thousand-Hour 500 C Durable 4H-SiC JFET Integrated Circuits

This work reports fabrication and testing of integrated circuits (ICs) with two levels of interconnect that consistently achieve greater than 1000 hours of stable electrical operation at 500 C in air ambient. These ICs are based on 4H-SiC junction field effect transistor (JFET) technology that integrates hafnium ohmic contacts with TaSi2 interconnects and SiO2 and Si3N4 dielectric layers over approximately 1-micrometer scale vertical topology. Following initial burn-in, important circuit parameters remain stable for more than 1000 hours of 500 C operational testing. These results advance the technology foundation for realizing long-term durable 500 C ICs with increased functional capability for sensing and control combustion engine, planetary, deep-well drilling, and other harsh-environment applications.

Microelectronics↗

Processing and Characterization of Thousand-Hour 500 C Durable 4H-SiC JFET Integrated Circuits

This work reports fabrication and testing of integrated circuits (ICs) with two levels of interconnect that consistently achieve greater than 1000 hours of stable electrical operation at 500 C in air ambient. These ICs are based on 4H-SiC junction field effect transistor (JFET) technology that integrates hafnium ohmic contacts with TaSi2 interconnects and SiO2 and Si3N4 dielectric layers over 1-m scale vertical topology. Following initial burn-in, important circuit parameters remain stable for more than 1000 hours of 500 C operational testing. These results advance the technology foundation for realizing long-term durable 500 C ICs with increased functional capability for sensing and control combustion engine, planetary, deep-well drilling, and other harsh-environment applications.

JFET↗

Characterization of a Laminate Flat Plate Diffusion Flame in Microgravity using PIV, Visible and CH Emissions

Motivated by fire safety concerns and the advent of long-term micro-gravity facilities, a cooperative program has been developed to study the mechanisms and material properties that control flow assisted (co-current) flame spread. This program has used as a common fire scenario a reacting steady-state boundary layer. Preliminary studies explored the aerodynamics of a reacting boundary layer by simulating a condensed fuel by means of a gas burner. Stability curves for ethane air flames were obtained and different burning regimes were identified. An important feature of this study was the independent identification of the different mechanisms leading to the instability of the flow. It was observed that fuel injection velocity and thermal expansion independently contributed to the separation of the flow at the leading edge of the burner. The occurrence of separation resulted in complex three-dimensional flow patterns that have a dominant effect on critical fire safety parameters such as the stand-off distance and flame length. This work was extended to a solid fuel (PMMA) leading to a Sounding Rocket experiment (Mini-Texus-6). The solid phase showed similar flow patterns, mostly present at low flow velocities (<100 mm/s) but the results clearly demonstrated that the thermal balance at the pyrolyzing fuel surface is the dominant mechanism that controls both stand-off distance and flame length. This thermal balance could be described in a global manner by means of a total mass transfer or "B" number. This "B" number incorporates surface re-radiation, radiative feedback and in-depth heat conduction as first prescribed by Emmons. The mass transfer number becomes the single parameter that determines the evolution of these fire safety variables (flame length, stand-off distance) and therefore can be used as a ranking criterion to assess the flammability of materials. The particular configuration is representative of the NASA upward flame spread test (Test 1) therefore this approach can be used in the interpretation of the results obtained from this test. Nevertheless, complete validation of this approach has not been fully achieved due, mainly because all the measurements necessary to compare with the theoretical predictions have not been obtained. Following these studies two different directions have been taken. The first attempts to elucidate the details of the gas phase combustion reaction and the associated flow field by means of quantitative and qualitative measurements. The second approach, a more practical one, is to apply this methodology to the assessment of material flammability. The former is currently being conducted with a gas burner because it allows for easier control and longer experimentation time. The results obtained so far will be presented in more detail. The latter is a new program therefore only a brief summary of the objectives will be presented.

Joulain, P.↗

Conceptual Design of Temperature-Controlled Fueled-Salt Irradiation Experiment to Support Demonstration of Advanced Nuclear Reactors

The irradiation testing of fuel-bearing molten salts is critical to supporting the development and demonstration of molten salt reactors (MSRs). These experiments can inform several important reactor design and safety parameters, including source term modeling, evolution of thermophysical properties with burn-up, and the degradation of structural materials under reactor relevant conditions. Idaho National Laboratory is designing an instrumented and heated high temperature molten salt-fueled irradiation capsule to study the behavior of the fuel salt during in-pile irradiation. This paper details the neutronics, thermal, and mechanical analysis performed to-date. Parametric studies are performed to assess a range of material, different experiment dimensions, two in-reactor positions, and the fuel enrichment used. Principal recommendations are to opt for a peripheral reactor position to alleviate neutronic constraints, a thin salt annulus to alleviate thermal constraints, and high-temperature alloys that provide additional safety margins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Performance of a vortex-controlled diffuser in an annular swirl-can combustor at inlet Mach numbers up to 0.53

A short, annular dump diffuser with suction stabilized vortices in the region of abrupt area change was tested with a full scale, annular swirl can combustor. The prediffuser area ratio was 1.4. Performance data were obtained for both isothermal and burning conditions at inlet temperatures of 589 to 895 K and pressures of 0.5 to 1.0 MPa for a range of diffuser inlet Mach numbers from 0.25 to 0.53. Suction rates were 0 to 20 percent of the total diffuser mass flow rate. Diffuser effectiveness increased from 47 percent without suction to approximately 80 percent for a total suction rate of 14 percent. Combustor total pressure loss for the same total suction rate was reduced from 6.8 percent without suction to 4.0 percent at an inlet Mach number of 0.40.

Smith, J. M.↗

Preliminary Characterizations of Altair Lunar Lander Slosh Dynamics and Some Implications for TVC Design

During thrust maneuvers, the sloshing of fuel in partially filled tanks could interact with the controlled system in such a way as to cause the overall system to be unstable. This failure mode could be a result of poor coordination between systems engineers of Structures, Propulsion, GN&C, Mission Operations, and other subsystems. Attentions to the following is a minimum: Placements of fuel tanks, Tank shapes and baffle designs, Separation of TVC BW from slosh mode frequencies, Adequacy of excursion range of engine gimbal actuators in all engine burns, BW of sensors (e.g., gyroscopes) and actuators (e.g., engine gimbal), Structural frequencies of spacecraft and engine mounts, Prediction of S/C's c.m. location, canting of gimbal null axis, others. Check overall TVC performance via validated simulation test bed. Modeling fuel slosh during spacecraft thrusting maneuvers • Placement of fuel tanks to guarantee stable interactions between fuel slosh mode and the S/C rigid-body mode • Estimation of slosh frequencies (as a function of mission phases): – Estimation of slosh mode damping • Some implications for Thrust Vector Control design: – Selection of TVC controller bandwidth – Adequacy of the excursion range of engine gimbal actuator • TVC system design: Complex Interactions between GN&C, Propulsion, Structure, and Other Subsystems

Thrust vector control↗