Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layered cathodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 919 records · Page 51
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Perspective—Potential Benefit of Li-Rich Cathode Materials: Reduction of Co and Ni Content Rather than Achievement of Ultra-High Capacities

In the conventional cycling protocol for lithium and manganese rich NMC layered oxides (LMRNMC), the upper cutoff voltage V cut is extended to ~ 4.8, to achieve capacities of similar to 250 mAh g -1 . With this mode of operation, structural rearrangements result in voltage fade upon cycling. Herein, a strategy is proposed to avoid these structural rearrangements based on (a) restricting V cut to values < ~ 4.6 to shut down the bulk instabilities, and (b) application of a (preferably) semi-coherent coating that protects the surface oxygen. The potential benefit of this strategy would be to minimize Co and Ni content, compared to Ni-rich NMC.

25 ENERGY STORAGE↗
DOE OSTI2025

Discharge Rate‐Driven Li 2 O 2 Growth Exhibits Unconventional Morphology Trends in Solid‐State Li‐O 2 Batteries

Solid-state lithium oxygen batteries (LOBs) are known for their enhanced safety, higher electrochemical stability, and improved energy density compared to liquid-state LOBs. However, the investigation of solid-state LOBs is limited with little understanding of their discharge and charge processes. In this work, a polymer-based solid-state LOB is used to investigate the effect of discharge rate on lithium peroxide (Li 2 O 2 ) formation, the oxygen evolution reaction (OER), and cycle performance. Notably, we observe a counterintuitive trend: Li 2 O 2 particle size increases with increasing discharge current density, in contrast to liquid systems. This behavior arises from inherent space charge layers that restrict Li⁺ transport under high current, and spatially heterogeneous active sites at the solid electrolyte–cathode interface, directly evidenced by small angle X-ray scattering (SAXS), which govern nucleation accessibility and promote site-selective Li 2 O 2 growth. Furthermore, higher current densities improve ORR and OER efficiency but accelerate anode degradation, while lower currents promote side reactions. These opposing effects result in a trade-off that defines an optimal discharge rate (0.1 mA cm -2 ) for maximizing cycle life. This study provides a new mechanistic perspective on discharge-driven processes in solid-state LOBs and offers practical guidelines for performance optimization in future high-energy battery systems.

Discharge current density↗
NASA NTRS2007

Cathode luminescence light source for broadband applications in the visible spectrum

A device and method for generating cathode luminescence is provided. The device and method generate broad spectrum electromagnetic radiation in the visible. A layer of particles, such as quartz or alumina powder, is exposed to electrons in a plasma discharge. Surface excitation of these particles or the generations/excitation of F-center sites give rise to luminescence.

Foster, John E.↗
DOE OSTI2025

The Sensitivity of Nickel Substitution in the Structural Design of Manganese-Based Layered and Lithiated Spinel Electrodes for Li-Ion Batteries

A concerted effort is being made at Argonne National Laboratory to explore and develop high-performance lithium-manganese-nickel-oxide cathode materials for the lithium battery industry. They are both energy- and cost-competitive relative to cobalt- and nickel-rich systems, such as LiCoO 2 , LiNi 0.8 Co 0.15 Al 0.05 O 2 , and LiNi 0.8 Mn 0.1 Co 0.1 O 2 . The recent discovery of the structural versatility of LiNi 0.5 Mn 0.5 O 2 , has revealed that it can exist in three configurations: lithiated spinel, partially disordered layered, and completely disordered rock salt within a common cubic-close-packed oxygen array. This versatility opens up the possibility of designing structurally integrated electrode components with interlinking 2-D (layered) and 3-D (spinel) channels for Li-ion transport. This paper highlights the sensitivity of Ni substitution and synthesis temperature on the structural and electrochemical properties of LiNi 0.50 Mn 0.50 O 2 , LiNi 0.53 Mn 0.47 O 2 , LiNi 0.47 Mn 0.53 O 2 , and LiNi 0.25 Mn 0.75 O 2 electrodes, as well as a cobalt-containing composition, LiNi 0.333 Mn 0.333 Co 0.333 O 2 , when synthesized at a relatively low temperature of 400 °C.

25 ENERGY STORAGE↗
DOE OSTI2025

Atomic layer deposited aluminum nitride for interface protection of lithium germanium thiophosphate solid electrolytes

Lithium germanium thiophosphate (LGPS) is an attractive solid-state electrolyte material due to its exceptionally high ionic conductivity (~1.2 × 10 –2 S cm –1 ), comparable to many organic liquid electrolytes commonly used in batteries. Despite the high conductivity of LGPS, the susceptibility of LGPS to deleterious degradation reactions has impeded its commercial adoption into solid-state batteries. In particular, the poor voltage stability of LGPS with high-voltage cathode or lithium metal potentials often results in dramatically increasing cell impedance during galvanic cycling. Here, we use aluminum nitride (AlN) as a protection layer for Li metal anode, applied directly to the LGPS at 250 °C using plasma-enhanced atomic layer deposition, to enhance cell performance by preventing LGPS-Li metal reactions. We compare the surface chemistry and electrochemical cycling performance of atomic layer-deposited AlN grown using both plasma N 2 and NH 3 precursors. Galvanostatic cycling and electrochemical impedance spectroscopy show that AlN-coated LGPS cells perform better than bare LGPS cells in contact with Li metal anodes, with the AlN able to improve cycling longevity by over a factor of 3 in certain cases. Finally, we utilize x-ray photoelectron spectroscopy (XPS) line scans to highlight the slow room-temperature reactivity between AlN and evaporated lithium metal, and a computational model is built to aid further XPS analysis.

25 ENERGY STORAGE↗
NASA NTRS1976

Lidar measurement of stratospheric dust from St. Augustine Volcano

The detection of a stratospheric dust layer of probable volcanic origin over Hampton, Va., on the evening of Jan. 28, 1976, with a 20-inch lidar system is reported. A digitized cathode-ray-tube trace of a return signal from altitudes of 12 to 24 km on January 28 is provided, and it is shown that 38% of the return was due to stratospheric aerosol. Noting that measurements on January 22 and February 2 showed no traces of this stratospheric dust layer, trajectories of dust-laden air parcels are followed from initiation at 0000 GMT on January 24 at the St. Augustine Volcano on Augustine Island, Alaska (59 deg N, 153 deg W). Analysis of the trajectories indicates that dust injected into the stratosphere at 59 deg N, 153 deg W could have been transported to Virginia in about 4 days. It is concluded that if the St. Augustine Volcano was the source of the dust, at least 23 deg of meridional transport from polar latitudes was observed.

Remsberg, E. E.↗
DOE OSTI2023

Stabilizing lattice oxygen redox in layered sodium transition metal oxide through spin singlet state

Abstract Reversible lattice oxygen redox reactions offer the potential to enhance energy density and lower battery cathode costs. However, their widespread adoption faces obstacles like substantial voltage hysteresis and poor stability. The current research addresses these challenges by achieving a non-hysteresis, long-term stable oxygen redox reaction in the P3-type Na 2/3 Cu 1/3 Mn 2/3 O 2 . Here we show this is accomplished by forming spin singlet states during charge and discharge. Detailed analysis, including in-situ X-ray diffraction, shows highly reversible structural changes during cycling. In addition, local CuO 6 Jahn-Teller distortions persist throughout, with dynamic Cu-O bond length variations. In-situ hard X-ray absorption and ex-situ soft X-ray absorption study, along with density function theory calculations, reveal two distinct charge compensation mechanisms at approximately 3.66 V and 3.99 V plateaus. Notably, we observe a Zhang-Rice-like singlet state during 3.99 V charging, offering an alternative charge compensation mechanism to stabilize the active oxygen redox reaction.

25 ENERGY STORAGE↗
DOE OSTI2021

The surface triple-coupling on single crystalline cathode for lithium ion batteries

Single crystalline (SC) cathode materials, which are less susceptible to micro/nano-cracks formation and offer better structure stability compared to the polycrystalline counterpart, have attained great attention. However, the parasitic side reactions at the cathode-electrolyte interface induces the loss of active species, which consequently leads to continual degradation of the electrochemical performances. Herein, a triple coupling of concentration-gradient Na+, F- co-doping and surface NaF coating are exploited for the first time on SC LiNi 0.5C o 0.2 Mn 0.3 O 2 cathode by the hydrolysis of NaPF 6 . This process regulates the external structure of materials by constructing a “sandwich” configuration from surface to bulk: rock salt - mixing zone - layered phase. The detailed interface transformation mechanism is revealed by Neutron powder diffraction (NPD), spherical aberration corrected high-resolution scanning transmission electron microscopy (HR-STEM), electron energy loss spectroscopy (EELS), and Ar+ sputtering assisted X-ray photoelectron spectroscopy (XPS). The synergistic effects endow the SC cathode with outstanding capacity retentions: 91.3% at 25 °C and 85% at 45 °C, after 500 cycles at 5 C between 3.0 and 4.5 V. In addition, a high full-cell reversible capacity of 168.9 mAh g -1 with a capacity retention of 92.4% is achieved after 300 cycles at 1 C. Multiple characterizations further indicate that these superior results are mainly ascribed to the overall structure integrity of SC material, the thin cathode electrolyte interface, high content of lithium fluoride, and the low solubility of transition metal ions. This work opens a new avenue to construct a benign interface towards high-performance lithium ion batteries.

lithium ion batteries↗
DOE OSTI2021

Building a spontaneously formed and self-healing protective layer with an F-rich electrochemically active organic molecule for ultra-stable Li metal batteries

Additives in the electrolyte act as engineers in Li metal batteries. Inspired by the superior cycle performance of organic materials in half cells, tetrafluoro-1,4-benzoquinone (TFBQ), the main structure of which has been widely applied as an organic cathode material, is utilized for the first time as an additive for Li metal protection. By chemical and electrochemical reactions between TFBQ and the Li metal surface, an F-rich interface layer is in situ formed on the Li metal surface during the charge and discharge process. From electrochemical tests and characterization, the powerful self-healing ability of the interface layer enabled by TFBQ is revealed, making an extremely stable Li metal anode. By using a lean electrolyte with 0.1 M TFBQ, the cycle life of Li|Li symmetric cells is increased at least 6 times compared to the control group. Moreover, impressive full cell performance was achieved. Ultra-stable Li–LFP cells showed a 0.026% average degradation for 600 cycles at 1C and Li–NMC622 cells showed a 36.8% higher capacity compared to the control group over 200 cycles at 0.5C, which are among the best results reported. Furthermore, this work efficiently and conveniently provides a new research direction to Li metal protection and Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Half-cell electrode assessments of a crossover-tolerant direct methanol fuel cell with a platinum group metal-free cathode

In this work, a platinum group metal- free (PGM-free) Fe-N-C oxygen reduction reaction (ORR) catalyst derived from metal organic framework precursors (Fe-MOF) is evaluated at the cathode side of a direct methanol fuel cell (DMFC). A wide range of methanol concentrations were used, and the performance of the DMFC using air was evaluated and compared to a commercial Pt/C cathode. We conducted our tests with a custom, integrated H 2 reference electrode that separately provided the anode and cathode overpotentials. This allowed us to perform a Tafel analysis on both electrodes and understand the dominant polarizations involved at the PGM-free cathode and the PtRu/C anode. Overall, we achieved a high cell performance using a Fe-N-C based catalyst under liquid methanol and air operation with a peak power density of 111 mW/cm 2 , where the cathode presented a markedly larger contribution to the voltage loss versus the anode. Additionally, we used nanoscale X-ray computed tomography (nano-CT) to image the Fe-N-C cathode and investigate the ionomer and pore size distributions allowing us to identify areas of improvement for catalyst layer fabrication.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Topology Optimization for Full-Cell Electrochemical Energy Storage Device

This code is used to conduct topology optimization of a general full cell energy storage device. The anode and cathode designs are optimized simultaneously, allowing possibility for interdigitation. The charging mechanism can consist of both electric double layer charging (EDLC) typically observed in capacitors and redox reaction typically observed in batteries.

Roy, Thomas↗
DOE OSTI2021

Reversible dual anionic-redox chemistry in NaCrSSe with fast charging capability

Utilizing the anionic redox reaction opens new approaches for the development of new cathode materials with extra capacities. Although, it suffers from several obstacles such as voltage hysteresis and sluggish kinetics. In this paper, a new layered chalcogenide-based on dual anionic-redox reaction is reported. The newly designed layered NaCrSSe exhibits the capacity of almost all Na + intercalation/deintercalation (137 mAh/g -1 at 50 mA/g), and a unique charge/discharge feature with a small polarization of 0.15 V and high energy efficiency of ~92% in initial cycles. Furthermore, a superior high-rate charge capacity of 115.5mAh/g -1 (83.7% retention) was achieved at 27.8 C (4000 mA/g -1 ). Systematic characterization studies on structure evolution and DFT calculation show the charge compensation of S and Se anions during cycling. Overall, these results will enrich the anion redox chemistry and provide valuable information for developing new anion-redox based cathode materials with high capacity and fast kinetics.

25 ENERGY STORAGE↗
DOE OSTI2022

A nitrogen- and carbonyl-rich conjugated small-molecule organic cathode for high-performance sodium-ion batteries

Organic-based cathode materials have attracted considerable attention for sustainable Na-ion batteries due to their great promise to overcome the issues arising from the insertion of large Na + into the rigid structures of conventional transition-metal-containing inorganic electrodes. The structural flexibility as a result of weak intermolecular interactions and simple electron- and ion-storage mechanisms found in organic compounds ensure facile and reversible transport of Na ions. In order to address the general drawbacks of small-molecule organic electrodes such as material dissolution in commonly used organic electrolytes and poor electronic conductivity, we report the use of a nitrogen- and carbonyl-rich highly extended π-conjugated small molecule, hexaazatrianthranylene (HATA) embedded quinone (HATAQ), as a cathode for sodium-ion batteries. The unique hydrogen bonds between highly functionalized conjugated HATAQ molecules allow supramolecular graphite-like 2D layered arrangements in the solid state which help facilitate the structural stability during long-term cycling and promote charge transfer. The compound delivers a capacity as high as 460 mA h g -1 at 500 mA g -1 and an excellent capacity retention of 99% (~138 mA h g -1 ) after 5000 cycles at an extremely high rate of 60 A g -1 . The reaction kinetics and redox mechanism of the material have been elucidated by several characterization techniques together with density functional theory (DFT) studies. The insights gained in this work could pave the way for ultra-high-performance small-molecule organic cathodes for sustainable energy storage.

25 ENERGY STORAGE↗
DOE OSTI2020

Analysis of an all-solid state nanobattery using molecular dynamics simulations under an external electric field

Present Li-ion battery (LIB) technology requires strong improvements in performance, energy capacity, charging-time, and cost to expand their application to e-mobility and grid storage. Li-metal is one of the most promising materials to replace commercial anodes such as graphite because of its 10 times higher specific capacity. However, Li-metal has high reactivity with commercial liquid electrolytes; thus, new solid materials are proposed to replace liquid electrolytes when Li-metal anodes are used. We present a theoretical analysis of the charging process in a full nanobattery, containing a LiCoO 2 cathode, a Li 7 P2S 8 I solid-state electrolyte (SSE), a Li-metal anode as well as Al and Cu collectors for the cathode and anode, respectively. In addition, we added a Li 3 P/Li 2 S film as a solid electrolyte interphase (SEI) layer between the Li-anode and SSE. Thus, we focus this study on the SEI and SSE. We simulated the charging of the nanobattery with an external voltage by applying an electric field. We estimated temperature profiles within the nanobattery and analyzed Li-ion transport through the SSE and SEI. Here, we observed a slight temperature rise at the SEI due to reactions forming $PS_{3}^{–}$ and $P_{2}S_{7}^{4}$$^{–}$ fragments at the interfaces; however, this temperature profile changes due to the charging current under the presence of the external electric field ε = 0.75 V Å –1 . Without the external field, the calculated open-circuit voltage (OCV) was 3.86 V for the battery, which is within the range of values of commercial cobalt-based LIBs. This voltage implies a spontaneous fall of available Li-ions from the anode to the cathode (during discharge). The charge of this nanobattery requires overcoming the OCV plus an additional voltage that determines the charging current. Thus, we applied an external potential able to neutralize the OCV, plus an additional 1.6 V to induce the transport of Li + from the cathode up to the anode. Several interesting details about Li + transport paths through the SSE and SEI are discussed.

25 ENERGY STORAGE↗
DOE OSTI2022

Achieving SEI preformed graphite in flow cell to mitigate initial lithium loss

The irreversible lithium loss due to the formation of solid electrolyte interphase (SEI) in the initial cycle on the graphite anode greatly reduces the overall cell energy density of lithium ion batteries, that is, the lost Li ions from forming SEI lead to the decrease of Li ions for the intercalation. The method of cathode prelithiation has been widely explored to compensate this lithium loss. However, these cathode additives with high lithium contents inevitably lower the loading of the cathode active materials. In this work, we report a novel approach to solve this challenge, a facile graphite prelithiation method by preforming SEI layers on the surface of graphite powders (Pre-SEI graphite) utilizing a specially designed flow cell. The Li accommodation in the graphite anode can be controlled by the operating time and current density in the flow cell for the electrochemical SEI formation. As a result, we demonstrate a 10% initial Columbic efficiency increase of the LiFePO 4 electrode in a full cell configuration using the Pre-SEI graphite, compared with the pristine graphite anode. The electrochemical preformation of SEI on the graphite powders offers a complete solution to offset initial lithium loss without a sacrifice of active cathode material loading.

25 ENERGY STORAGE↗
DOE OSTI2025

Modulating physicochemical interfaces enables li-rich oxides based ceramic solid-state li batteries under ambient conditions

Li-rich layered oxides exhibit promising potential applications in high-energy-density solid-state lithium metal batteries. Nevertheless, the strong oxidative oxygen species generate at high voltage, which poses great challenges to positive electrode-side interface stability. Herein, a robust in-situ polymerization gel polymer electrolyte with bifunctional additives is designed for interface modification. These additives, include lithium difluoro(oxalate) borate and LiPO 2 F 2 , regulate the Li + chemical environment in gel polymer electrolyte to enhance crosslink density without residual oligomer, which reduce gas generation and suppress contact loss, thus avoiding interfacial impedance divergence. Concurrently, the designed gel polymer electrolyte enables a wide electrochemical stability window (up to 4.7 V) and a high Li + transference number (0.82). Additionally, the additives induced F- and B-rich inorganic cathode-electrolyte interphase inhibits side reactions and oxygen/transition metal loss effectively, stabilizing the chemical interface. The as-constructed Li-rich layered oxides-based ceramic solid-state lithium metal batteries with gel polymer electrolyte interface modification exert a high discharge capacity of 276.5 mAh g -1 at 30 °C without external pressure, delivering a retention of 81.7% after 100 cycles at 25 mA g -1 during 2.0-4.7 V. This work provides a guideline for developing high-voltage solid-state lithium metal batteries via interfacial design.

Hu, Xinchao [Xiamen University (China)]↗
DOE OSTI2020

Atomic-Level Understanding of Surface Reconstruction Based on Li[Ni x Mn y Co 1–x–y ]O 2 Single-Crystal Studies

The stability of cathode particle surfaces that are directly exposed to the electrolyte is one of the most crucial and determining factors for cathode performance at high operating voltages. Theory has predicted a strong dependence of surface stability on chemical compositions as well as surface facets of layered oxides, yet conflicting results on the correlations exist as most experimental studies focus on cycled secondary particles recovered from composite electrodes. Here, we synthesize well-formed Li[Ni x Mn y Co 1–x–y ]O 2 (NMC) single-crystal samples, carefully define pristine surface properties, and then monitor their evolution with cycling. Atomic-resolution scanning transmission electron microscopy (STEM) imaging and electron energy loss spectroscopy (EELS) analysis show the formation of a surface reconstruction layer (SRL) as well as an extended surface reduction layer on pristine, Li-permeable non-(001) surfaces, even before cycling. We reveal a transition region with chemical gradient, in which the layered structure gradually densifies and eventually transforms into the SRL on the top surface. Contrary to these observations, no SRL is observed on pristine, Li-impermeable (001) surfaces, revealing the facet-dependent nature of surface reconstructions during particle synthesis. Upon electrochemical cycling, significant composition-and facet-dependent SRL growth is observed. The driving force and mechanism for surface reconstruction are further discussed. The present study provides insights into the origin as well as the nature of SRLs, highlighting the significance of surface engineering in cathode material optimization.

25 ENERGY STORAGE↗
DOE OSTI2021

Composite bilayer coatings for high capacity cathodes and anodes

An electrode comprises an electrode core. A composite bilayer coating is conformally disposed on the electrode core. The composite bilayer coating comprises a first layer disposed on at least a portion of the electrode core. The first layer comprises a metal fluoride, a metal oxide or a metal sulfide. A second layer is disposed on the first layer and comprises a metal fluoride, a metal oxide or a metal sulfide.

Mane, Anil U.↗