SEARCH · Engineering Papers

Results for “synchronized sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5

All sources NASA NTRS DOE OSTI

NASA NTRS2001

An OFDM System Using Polyphase Filter and DFT Architecture for Very High Data Rate Applications

This paper presents a conceptual architectural design of a four-channel Orthogonal Frequency Division Multiplexing (OFDM) system with an aggregate information throughput of 622 megabits per second (Mbps). Primary emphasis is placed on the generation and detection of the composite waveform using polyphase filter and Discrete Fourier Transform (DFT) approaches to digitally stack and bandlimit the individual carriers. The four-channel approach enables the implementation of a system that can be both power and bandwidth efficient, yet enough parallelism exists to meet higher data rate goals. It also enables a DC power efficient transmitter that is suitable for on-board satellite systems, and a moderately complex receiver that is suitable for low-cost ground terminals. The major advantage of the system as compared to a single channel system is lower complexity and DC power consumption. This is because the highest sample rate is half that of the single channel system and synchronization can occur at most, depending on the synchronization technique, a quarter of the rate of a single channel system. The major disadvantage is the increased peak-to-average power ratio over the single channel system. Simulation results in a form of bit-error-rate (BER) curves are presented in this paper.

Kifle, Muli↗

NASA NTRS1989

On optimizing a constellation of altimetric satellites for measuring global oceanic mesoscale

The orbital configuration of the Eos polar-platform constellation is examined to determine if baseline orbital parameters are appropriately specified to meet the mission goal of measuring global oceanic mesoscale variability. Using the Nyquist sampling theorem, spatial and temporal measurement requirements are first established for the constellation. Based upon these requirements, the optimum solution indicates that a total of five spacecraft are required to meet the mesoscale mapping task. Additional analyses are performed on both a two-platform configuration as well as the complete four-platform Eos constellation. The results of these calculations show that an optimized configuration of four properly-phased Eos platforms, placed into identical 835-km sun-synchronous orbits with 13-day repeat periods, can very nearly meet statistically significant sampling criteria for mapping global oceanic mesoscale variability.

Chase, Robert↗

NASA NTRS1983

Orbital and cloud cover sampling analyses for multisatellite earth radiation budget experiments

Computer simulations have been performed to determine the geographical and temporal coverage of various satellite orbits and scanning and nonscanning radiometers for earth radiation budget measurements. These results were used to simulate the sampling of a diurnally varying cloud and radiation field for several different satellite systems to estimate errors in regional monthly mean reflected radiation. The combined results indicate that coincient observations with a minimum of one sun-synchronous satellite and a midinclined orbit satellite are needed to obtain the required regional, zonal, and global coverage with sufficient temporal sampling for obtaining accurate estimates of monthly mean reflected solar radiation. Overall, the best sampling capability and lowest errors were obtained with a three-satellite system, i.e., two sun-synchronous satellites with different equatorial crossing times combined with either a 46 or 57-deg orbit satellite. The results from these analyses have been used in defining a joint NASA-NOAA multisatellite mission for an earth radiation budget experiment.

Harrison, E. F.↗

NASA NTRS1995

Pulse Code Modulation (PCM) encoder handbook for Aydin Vector MMP-900 series system

This handbook explicates the hardware and software properties of a time division multiplex system. This system is used to sample analog and digital data. The data is then merged with frame synchronization information to produce a serial pulse coded modulation (PCM) bit stream. Information in this handbook is required by users to design congruous interface and attest effective utilization of this encoder system. Aydin Vector provides all of the components for these systems to Goddard Space Flight Center/Wallops Flight Facility.

Raphael, David↗

NASA NTRS1994

Experiment K-7-23: Effect of Spaceflight on Level and Function of Immune Cells: Immunology Studies - Part 1

Two different experiments were carried out in this segment of the immunology protocol for samples received from rats flown on Cosmos 2044. Control groups included vivarium, synchronous and antiorthostatically suspended rats. In the first experiment, rat bone marrow cells were examined in Moscow for their response to recombinant murine colony stimulating factor-granulocyte / monocyte (CSF-GM). In the second experiment, rat spleen and bone marrow cells were stained in Moscow with a variety of antibodies directed against cell surface antigenic markers. These cells were preserved and shipped to the United States for analysis on a flow cytometer. The results of the studies indicated that bone marrow cells from flown and suspended rats showed a decreased response to CSF-GM as compared to bone marrow cells from control rats. Spleen cells from flown rats showed increased percentages of suppressor-cytotoxic-T and helper-T cells amongst the entire cell population. Bone marrow cells showed an increase in the percentage of helper-T cells in the myelogenous population and increased percentages of anti-asialo GM-1 bearing, interleukin-2 receptor bearing, pan-T and helper-T cells in the lymphocytic population. Cell populations from rats suspended antiorthostatically did not follow the same pattern of distribution of leukocytes as cell populations for flown rats. These results are similar, but not identical to, earlier results from Cosmos 1887, and confirm that space flight can have profound effects on immune system components and activities.

Sonnenfeld, G.↗

NASA NTRS2013

Soil Moisture Active Passive (SMAP) observer power system architecture

The Soil Moisture Active and Passive (SMAP) observer is scheduled for launch in 2014. The primary science objective of SMAP is the high-resolution mapping of earth’s soil moisture. These measurements will be used to enhance understanding of processes that link the water, energy and carbon cycles, and to extend the capabilities of weather and climate prediction models. The SMAP orbit, sun-synchronous with an altitude of 680 km, was chosen to optimize the sampling characteristics of the instruments while ensuring that the resolution requirements are met. The combined active radar and passive radiometer measurement approach takes advantage of the spatial resolutions of the radar (3 km x 1000 km) and the radiometer (39 km x 47 km).

Carr, Gregory↗

NASA NTRS2021

Sample Return Containerization and Planetary Protection Using Brazing for Breaking the Chain of Contact to Mars

Planetary protection of Mars samples returned to Earth in a future NASA mission is a critical part of preventing uncontrolled biological materials being released from the samples. The planetary protection process requires addressing the potential risks and would involve “breaking the chain of contact (BTC)”, where any returned material reaching Earth for further analysis would have to be sealed inside a container with extremely high confidence. The sterilization process would require destroying any potential biological materials that may contaminate the external surface of the container. A novel process for containing the returned samples has been conceived and developed at JPL. The process consists of using induction heated brazing to synchronously sterilize, separate, seam and seal the container. In this case. the braze material is heated to the level of melting at temperatures higher than 500°C to assure sterilizing exposed areas since carbon bonds are broken above this temperature. The container that encloses the samples consists of double walls with interstitial space that is Earth-clean. The process consists of two-steps, where one was intended to be prepared on Earth and the second potentially executed on orbit around Mars. The latest results of this study that established the needed capability are described and discussed in this manuscript.

Shirajian, Nareg↗

NASA NTRS1974

Shuttle extravehicular activity signal processor pulse amplitude modulation decommutator

To provide data with long-term stability and accuracy, the pulse amplitude modulation (PAM) decommutator was synchronized to the PAM-return to zero wavetrain, and each channel was sampled with a common sample and hold circuit and digitized sequentially. The digital value of each channel was then scaled by the digital value of the calibration channels. The corrected digital value of each channel was stored for one complete frame and then transferred to the multiplexer-demultiplexer at a high rate in one block of serial digital data. A test model was built to demonstrate this design approach taken for the PAM decom and performance data was provided. The accuracies obtained with various signal to noise ratios are shown.

Noble, D. E.↗

NASA NTRS2018

Exploration Ground Data Systems (xGDS) Overview

xGDS supports rapid scientific decision making by synchronizing the time and mapped location of observation notes, instrument data, photos, video, samples and other data. xGDS is a suite of web tools, developed at NASA Ames Research Center to support remote science operations in analog missions and prototype new ideas for planetary exploration. During operations, xGDS displays science data in real-time with geographic context, supporting key decisions (e.g. sample site selection). Post-operations, xGDS enables efficient analysis of data by correlating data products in time and on the map. xGDS has been developed in close collaboration with science teams since 2009, and used enthusiastically by upwards of 100 scientists to support scientific field research and data analysis.

Ground Data System↗

NASA NTRS1978

Sampling analysis for the Earth Radiation Budget Satellite System mission based on orbital coverage and cloud variability

The reported study represents an extension of an investigation by Harrison et al. (1976). Based on the results of sampling studies, two 98 deg inclined orbits coupled with a 56 deg inclination orbit appear to satisfy the science requirements on both regional and zonal scales. The NOAA sun-synchronous satellites in the TIROS-N series could adequately cover the high latitudes and a satellite having an inclination of 56 deg could provide sampling in the mid and low latitude areas where variations in radiation energetics are most dynamic. Attention is given to studies of time and space coverage, zonal evaluations, a regional analysis, and statistics describing the regional variations of cloud cover. A table is presented with data concerning the uncertainty of monthly mean reflected irradiance due to cloud variability for selected northern hemisphere regions.

Harrison, E. F.↗

NASA NTRS1994

Evaluating the design of an earth radiation budget instrument with system simulations. Part 2: Minimization of instantaneous sampling errors for CERES-I

Much of the new record of broadband earth radiation budget satellite measurements to be obtained during the late 1990s and early twenty-first century will come from the dual-radiometer Clouds and Earth's Radiant Energy System Instrument (CERES-I) flown aboard sun-synchronous polar orbiters. Simulation studies conducted in this work for an early afternoon satellite orbit indicate that spatial root-mean-square (rms) sampling errors of instantaneous CERES-I shortwave flux estimates will range from about 8.5 to 14.0 W/m on a 2.5 deg latitude and longitude grid resolution. Rms errors in longwave flux estimates are only about 20% as large and range from 1.5 to 3.5 W/sq m. These results are based on an optimal cross-track scanner design that includes 50% footprint overlap to eliminate gaps in the top-of-the-atmosphere coverage, and a 'smallest' footprint size to increase the ratio in the number of observations lying within to the number of observations lying on grid area boundaries. Total instantaneous measurement error also depends on the variability of anisotropic reflectance and emission patterns and on retrieval methods used to generate target area fluxes. Three retrieval procedures from both CERES-I scanners (cross-track and rotating azimuth plane) are used. (1) The baseline Earth Radiaton Budget Experiment (ERBE) procedure, which assumes that errors due to the use of mean angular dependence models (ADMs) in the radiance-to-flux inversion process nearly cancel when averaged over grid areas. (2) To estimate N, instantaneous ADMs are estimated from the multiangular, collocated observations of the two scanners. These observed models replace the mean models in computation of satellite flux estimates. (3) The scene flux approach, conducts separate target-area retrievals for each ERBE scene category and combines their results using area weighting by scene type. The ERBE retrieval performs best when the simulated radiance field departs from the ERBE mean models by less than 10%. For larger perturbations, both the scene flux and collocation methods produce less error than the ERBE retrieval. The scene flux technique is preferable, however, because it involves fewer restrictive assumptions.

Stowe, Larry↗

NASA NTRS1989

Hybrid Analog/Digital Receiver

Advanced hybrid analog/digital receiver processes intermediate-frequency (IF) signals carrying digital data in form of phase modulation. Uses IF sampling and digital phase-locked loops to track carrier and subcarrier signals and to synchronize data symbols. Consists of three modules: IF assembly, signal-processing assembly, and test-signal assembly. Intended for use in Deep Space Network, but presumably basic design modified for such terrestrial uses as communications or laboratory instrumentation where signals weak and/or noise strong.

Brown, D. H.↗

NASA NTRS1974

Shuttle user analysis (study 2.2): Volume 3. Business Risk And Value of Operations in space (BRAVO). Part 4: Computer programs and data look-up

Computer program listings as well as graphical and tabulated data needed by the analyst to perform a BRAVO analysis were examined. Graphical aid which can be used to determine the earth coverage of satellites in synchronous equatorial orbits was described. A listing for satellite synthesis computer program as well as a sample printout for the DSCS-11 satellite program and a listing of the symbols used in the program were included. The APL language listing for the payload program cost estimating computer program was given. This language is compatible with many of the time sharing remote terminals computers used in the United States. Data on the intelsat communications network was studied. Costs for telecommunications systems leasing, line of sight microwave relay communications systems, submarine telephone cables, and terrestrial power generation systems were also described.

Source record↗

NASA NTRS1981

CO2 laser waveguiding in proton implanted GaAs

Surface layers capable of supporting optical modes at 10.6 microns have been produced in n-type GaAs wafers through 300 keV proton implantation. The dominant mechanism for this effect appears to be free carrier compensation. Characterization of the implanted layers by analysis of infrared reflectivity spectra and synchronous coupling at 10.6 microns produced results in good agreement with elementary models. These results of sample characterization by infrared reflectivity and by CO2 laser waveguiding as implanted are presented and evaluated.

Jenkinson, H. A.↗

NASA NTRS1989

Modula-2*: An extension of Modula-2 for highly parallel programs

Parallel programs should be machine-independent, i.e., independent of properties that are likely to differ from one parallel computer to the next. Extensions are described of Modula-2 for writing highly parallel, portable programs meeting these requirements. The extensions are: synchronous and asynchronous forms of forall statement; and control of the allocation of data to processors. Sample programs written with the extensions demonstrate the clarity of parallel programs when machine-dependent details are omitted. The principles of efficiently implementing the extensions on SIMD, MIMD, and MSIMD machines are discussed. The extensions are small enough to be integrated easily into other imperative languages.

Tichy, Walter F.↗

NASA NTRS1992

Estimation and enhancement of real-time software reliability through mutation analysis

A simulation-based technique for obtaining numerical estimates of the reliability of N-version, real-time software is presented. An extended stochastic Petri net is employed to represent the synchronization structure of N versions of the software, where dependencies among versions are modeled through correlated sampling of module execution times. Test results utilizing specifications for NASA's planetary lander control software indicate that mutation-based testing could hold greater potential for enhancing reliability than the desirable but perhaps unachievable goal of independence among N versions.

Geist, Robert↗

NASA NTRS2014

Preliminary Results of the NASA Beacon Receiver for Alphasat Aldo Paraboni TDP5 Propagation Experiment

NASA Glenn Research Center (GRC) and the Politecnico di Milano (POLIMI) have initiated a joint propagation campaign within the framework of the Alphasat propagation experiment to characterize rain attenuation, scintillation, and gaseous absorption effects of the atmosphere in the 40 GHz band. NASA GRC has developed and installed a K/Q-band (20/40 GHz) beacon receiver at the POLIMI campus in Milan, Italy, which receives the 20/40 GHz signals broadcast from the Alphasat Aldo Paraboni TDP#5 beacon payload. The primary goal of these measurements is to develop a physical model to improve predictions of communications systems performance within the Q-band. Herein, we describe the design and preliminary performance of the NASA propagation terminal, which has been installed and operating in Milan since May 2014. The receiver is based upon a validated Fast Fourier Transform (FFT) I/Q digital design approach utilized in other operational NASA propagation terminals, but has been modified to employ power measurement via a frequency estimation technique and to coherently track and measure the amplitude of the 20/40 GHz beacon signals. The system consists of a 1.2-m K-band and a 0.6-m Qband Cassegrain reflector employing synchronous open-loop tracking to track the inclined orbit of the Alphasat satellite. An 8 Hz sampling rate is implemented to characterize scintillation effects, with a 1-Hz measurement bandwidth dynamic range of 45 dB. A weather station with an optical disdrometer is also installed to characterize rain drop size distribution for correlation with physical based models.

propagation↗

NASA NTRS2015

Performance of the NASA Beacon Receiver for the Alphasat Aldo Paraboni TDP5 Propagation Experiment

NASA Glenn Research Center (GRC) and the Politecnico di Milano (POLIMI) have initiated a joint propagation campaign within the framework of the Alphasat propagation experiment to characterize rain attenuation, scintillation, and gaseous absorption effects of the atmosphere in the 40 gigahertz band. NASA GRC has developed and installed a K/Q-band (20/40 gigahertz) beacon receiver at the POLIMI campus in Milan, Italy, which receives the 20/40 gigahertz signals broadcast from the Alphasat Aldo Paraboni Technology Demonstration Payload (TDP) no. 5 beacon payload. The primary goal of these measurements is to develop a physical model to improve predictions of communications systems performance within the Q-band. Herein, we describe the design and preliminary performance of the NASA propagation terminal, which has been installed and operating in Milan since June 2014. The receiver is based upon a validated Fast Fourier Transform (FFT) I/Q digital design approach utilized in other operational NASA propagation terminals, but has been modified to employ power measurement via a frequency estimation technique and to coherently track and measure the amplitude of the 20/40 gigahertz beacon signals. The system consists of a 1.2-meter K-band and a 0.6-meter Q-band Cassegrain reflector employing synchronous open-loop tracking to track the inclined orbit of the Alphasat satellite. An 8 hertz sampling rate is implemented to characterize scintillation effects, with a 1-hertz measurement bandwidth dynamic range of 45 decibels. A weather station with an optical disdrometer is also installed to characterize rain drop size distribution for correlation with physical based models.

propagation↗