Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “air separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Nitrogen evolution, NO X formation and reduction in pressurized oxy coal combustion

Oxy-combustion is one of the most prominent solutions for reducing CO 2 emissions from coal-fired power plants using carbon-capture-and-utilization technology. However, when compared to air combustion at atmospheric pressure, oxy-combustion is very expensive, owing to the significant efficiency penalties associated with air separation, flue gas recirculation (FGR), treatment, compression, and storage or transit of CO 2 . In comparison, pressurized oxy-combustion (POC) is more efficient as it recovers a significant amount of heat energy from the flue gas moistures. Nevertheless, CO 2 derived from pressurized oxy coal combustion has impurities, e.g., acid gases (NO X and SO X ) that can corrode the plant equipment, transport lines as well as deteriorating effect on the environment. Fortunately, in pressurized combustion systems, both NO X and SO X can be scrubbed by a single-column direct contact cooler (DCC), but this requires a minimum ratio of NO X to SO X at the inlet to be efficiently removed. Therefore, NOx is one of the important hindering parameters in commercializing the pressurized oxy-combustion. Although NOx evolution during oxy-coal combustion has been explored extensively at 1 atm, higher pressure studies are rare. Much still needs to be done to better understand the NO X mechanism and the effects of different parameters on NO X emissions under these conditions. Here, this paper reviews the published literature on nitrogen evolution, NO X formation and reduction in pressurized oxy-coal combustion. At higher pressures, the NO X from fuel-bound nitrogen is generated through volatiles, tar and char, all of which are discussed. Where literature is not available, the effect of pressure on NOx evolution in different stages of coal combustion is predicted through CHEMKIN simulation. Homogeneous and heterogeneous pathways of NO X formation and their destruction in pressurized oxy-coal combustion are evaluated. Additionally, the effect of pressure on a few mature and commercialized NOx abatement methods is explored. In the last, the future perspective and recommendation are given. This review will aid in the provision of basic knowledge about NOx evolution and control in pressurized fuel combustion, as well as the identification of new research areas to pursue.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Net Electronic Charge as an Effective Electronic Descriptor for Oxygen Release and Transport Properties of SrFeO 3 -based Oxygen Sorbents

Perovskite oxides, as oxygen sorbents, exhibit excellent potential in thermochemical redox applications such as chemical looping air separation (CLAS), resulting from their excellent redox properties and high tunability. The structural and compositional flexibility of perovskites, while making these mixed oxides highly versatile, also poses challenges for their design and optimization. Moreover, the elevated operating temperature and dynamic oxygen partial pressure swings during redox processes add additional complications for oxygen sorbent design. From a fundamental standpoint, finding simple yet effective descriptors for the effect of cation substitutions on oxygen sorbents’ redox and oxygen transport properties are of significant importance for rational optimization of perovskite-based oxygen sorbents. In the present study, a series of A/B-site-doped SrFeO 3-δ perovskites are investigated using density functional theory (DFT) + U simulations. From these simulations, an effective electronic structural descriptor, the net electronic charge (Δe) of oxygen anions, is extracted based on its excellent correlations with vacancy formation energy, experimentally derived oxygen capacity, and oxygen vacancy migration barrier. Overall, these findings provide an effective tool to correlate the oxygen sorbents’ redox performances with a simple yet physically meaningful descriptor for rational design and optimization of perovskites in the context of CLAS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Techno-economic performances and life cycle greenhouse gas emissions of various ammonia production pathways including conventional, carbon-capturing, nuclear-powered, and renewable production

Ammonia (NH 3 ) is conventionally produced using fossil natural gas (NG) for hydrogen production through steam reformation and synthesis in the Haber–Bosch (HB) process. The global conventional ammonia production contributes more than 420 million tons of CO 2 emissions annually. Here, in this work, we investigated the techno-economics and well-to-plant-gate (WTG) greenhouse gas (GHG) emissions of conventional NG-based, carbon-capturing, nuclear-powered, and renewable ammonia production by developing an engineering process model for each. Carbon-capturing ammonia production refers to the NG-based ammonia production while capturing CO 2 and transporting it via pipelines for storage or utilization. Nuclear-powered and renewable ammonia production represents an alternative ammonia production through water electrolysis, air separation, and the HB process using carbon-free energy sources. Nuclear and renewable energy sources are assumed to be used for nuclear-powered and renewable ammonia production, respectively. Sensitivity analyses are performed for CO 2 pipeline transport distances, potential carbon capture tax credits, and clean H 2 production cost. Carbon-capturing ammonia production reduces WTG GHG emissions by 55–70% compared to conventional NG-based ammonia production methods. Nuclear-powered and renewable ammonia production almost eliminate GHG emissions since energy supply is either zero carbon or near-zero carbon. However, when $4.16–4.83 per kg is the cost assumed for clean H 2 production using state-of-the-art electrolysis technologies, the levelized costs of nuclear-powered and renewable ammonia are calculated to be $0.92–1.06 per kg NH 3 , which are approximately four times higher than the conventional NG-based ammonia production cost. The cost of CO 2 emission avoidance is estimated in the range of $266–318 per metric ton of CO 2 for nuclear-powered and renewable ammonia production. The clean H 2 production cost is the major contributor to the levelized costs of nuclear-powered and renewable ammonia production. A lower production cost, near $1 per kg H 2 , for clean H 2 is required for nuclear-powered and renewable ammonia production to be cost-competitive with conventional NG-based ammonia production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Oxygen Storage Incorporated Into Net Power and the Allam–Fetvedt Oxy-Fuel sCO2 Power Cycle—Techno-Economic Analysis

Abstract With the planned future reliance on variable renewable energy, the ability to store energy for prolonged time periods will be required to reduce the disruption of market fluctuations. This paper presents a method to analyze a hybrid liquid-oxygen (LOx) storage/direct-fired supercritical carbon dioxide (sCO2) power cycle and optimize the economic performance over a diverse range of scenarios. The system utilizes a modified version of the NET Power process to produce energy when energy demand exceeds the supply while displacing much of the cost of the air separation unit (ASU) energy requirements through cryogenic storage of oxygen. The model uses marginal cost of energy data to determine the optimal times to charge and discharge the system over a given scenario. The model then applies ramp rates and other time-dependent factors to generate an economic model for the system without storage considerations. The size of the storage system is then applied to create a realistic model of the plant operation. From the real plant operation model, the amount of energy charged and discharged, the capital expenditures (CAPEX) of each system, energy costs and revenue and other parameters can be calculated. The economic parameters are then combined to calculate the net present value (NPV) of the system for the given scenario. The model was then run through the SMPSO genetic algorithm in Python for a variety of geographic regions and large-scale scenarios (high solar penetration) to maximize the NPV based on multiple parameters for each subsystem. The LOx storage requirements will also be discussed.

Engineering↗
DOE OSTI2020

Oxy-Combustion System Process Optimization

The overall objective of this work is to develop a new chemical absorbent-based, high pressure, CO 2 purification system to remove the residual oxygen that currently contaminates the recovered CO 2 , and to optimize the Pressurized Oxy-Combustion (POxC) process to minimize the Cost of Electricity (COE) generated in this advanced combustion process. TDA developed and validated the performance of the oxygen removal system for CO 2 purification. In collaboration with the Advanced Power & Energy Program (APEP) of University of California, Irvine (UCI), we optimized the POxC process, including thermal management, heat integration, and power cycle optimization using process design and modeling supported with Aspen Plus® process simulations. The techno-economic analysis results indicate that the pressurized oxycombustion coal power plant with Ion-transport membrane (ITM) air separation unit (ASU) (Case 2 – 30.55%) does not show an advantage over a cryogenic ASU (Case 1 – 31.24%) while TDA’s sorption-based ASU (Case 4 - 32.61%) shows a significant advantage over the cryogenic ASU (Case 1 – 331.24%). The specific plant costs show a wide range with a low of $2544/kW for Case 11C (TDA ASU, co-sequestering the SO x , and ultra-supercritical steam cycle) to a high of $2975/kW for Case 12A (cryogenic ASU and sCO 2 cycle). In general, the ITM ASU based cases have lower specific plant costs than the corresponding cryogenic ASU based cases while the TDA ASU based cases show the lowest specific plant costs. The main reason for lowering these costs is the higher overall plant thermal efficiency which decreases the plant cost on a $ per kW basis. Next comparing the cases with different power cycle working fluid conditions in terms of temperature and pressure while all utilizing steam, similar trends as the plant costs may be observed. However, with the supercritical CO 2 (sCO 2 ) cycle, the increase in thermal efficiency of the sCO 2 cycle was not able to offset its increase in plant cost making the plant costs higher than those of the corresponding steam cycle cases. The Cost of Electricity (COE) again shows similar trends as the specific plant costs. The COE for Case 11C at $110.1/MWh is also the lowest, but among all cases that do not co-sequester the SO x , Case 12C (TDA ASU and sCO 2 cycle) has the lowest COE at $\$$117.5/MWh while the highest is for Case 8A (cryogenic ASU and supercritical steam cycle) at $130.4/MWh.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Computational Fluid Dynamics Modeling to Simulate a Combined Reforming Process for Syngas and Hydrogen Production

An Oxygen Transport Membrane (OTM) combined reforming technology for producing syngas and hydrogen integrates the advantages of multiple processes—steam methane reforming (SMR), autothermal reforming (ATR), an air separation unit (ASU)—into a single integrated technology. The OTM consists of a primary reforming tube, in which desulfurized natural gas is partially reformed by steam at high pressure in the presence of a metal catalyst. This process is followed in series by a ceramic OTM with a secondary reformer, in which residual methane reforms and O 2 - ions react with a portion of the CO and H 2 fuel to provide the heat to support both primary and secondary reforming. Although the OTM combined reformer technology for syngas and H 2 production has been substantially developed in the last decade, several challenges that affect the overall production efficiency and reliability are yet to be fully understood, addressed, and resolved. Therefore, developing Computational Fluid Dynamics (CFD) models that incorporate fluid dynamics, mass transport, kinetics, heat transport, and structural mechanics is critical to understanding and minimizing the probability of tube failures during the startup and operation. In this report, an exhaustive literature review was performed to survey the current state of technology for producing syngas and H 2 using either conventional or renewable energy sources. The feedstocks reviewed include natural gas and coal for the conventional technologies, whereas biomass, solar, wind, and nuclear energy for the renewable technologies. The existing industry-grade COMSOL multiphysics models of OTM were upgraded for the latest software release. In addition, they were improved to help achieve grid and solver independence and were successfully ported on the ORNL high-performance computing clusters to speed up their run times. A 42% reduction in the simulation run time was achieved. A new higher-fidelity CFD model of an OTM tube was developed in the StarCCM+ simulation platform. This new model was designed to simulate various physics using first principles, e.g., turbulent flow, heat transfer, and chemical reactions while avoiding unnecessary simplifications. The resulting predictions were qualitatively assessed and provided useful insights into the multiphysics complexity of an OTM tube.

08 HYDROGEN↗
DOE OSTI2022

Performance and Cost Potential for Exemplar Direct Supercritical Carbon Dioxide Natural Gas Plants

This report presents the techno-economic analysis (TEA) optimization results of natural gas-fired utility-scale power plants based on the direct supercritical carbon dioxide (sCO 2 ) power cycle. To identify optimum plant configuration, the study also considered three different cases (Case A, Case B, Case C) with varying levels of thermal integration with the plant air separation unit (ASU). A fourth case (Case D), which is based on a patent from 8 Rivers, was also considered and includes thermal integration with the ASU as well as compressed recycle carbon dioxide (CO 2 ) gas. The four direct sCO 2 power plants offered similar or slightly higher plant efficiencies than the reference NGCC plants based on an F-class gas turbine with carbon capture and storage (CCS). LCOE of the direct sCO 2 plants is 13.5–17.2 percent higher than the reference NGCC plants with CCS due to higher capital costs associated with the ASU and sCO 2 power block. Recuperators make up over 50 percent of the power cycle costs. Consequently, any research and development (R&D) efforts to reduce the recuperator capital costs will be beneficial for the technology commercialization. The study also investigated the impact of co-firing landfill gas (LFG) and natural gas on plant efficiency, LCOE, and CO 2 emissions. Increasing the LFG co-firing from 0 percent to 50 percent (mass basis), decreased the plant efficiency by 0.3 percentage points and increased the LCOE by 3 percent. Due to high inherent CO 2 capture rates, direct sCO 2 plants have strong potential to achieve net-zero CO 2 emissions with LFG and natural gas co-firing.

03 NATURAL GAS↗
DOE OSTI2023

Biomass Gasification for Chemicals Production Using Chemical Looping Techniques (Final Report)

The Ohio State University (OSU) is investigating the Biomass to Syngas (BTS) chemical looping technology to produce syngas for chemical production applications from biomass under US Department of Energy (DOE) Award #DE-EE0007530. The BTS process aligns with the programmatic area of interest of “Conversion, via biological, thermal, catalytic or chemical means, of acceptable feedstocks into advanced biofuels and/or biobased products including intermediate and end-use products”. Compared to conventional biomass gasification processes, the BTS process eliminates the need for air separation units and tar reforming reactors, which leads to energy efficiency improvement and capital cost reduction. The overall objective is to ascertain the potential of biomass gasification based on the chemical looping technique through mitigation of the possible techno-economic challenges in the steps of scale up for commercialization. The scope of work consists of 1) designing, constructing and operating a 10 kWth commercially scalable sub-pilot BTS system and; 2) completing a comprehensive techno-economic analysis (TEA) of the BTS process using methanol production as an example. Over the course of the project, the project team completed the design, fabrication, and operation of a 10 kWth sub-pilot scale test unit for the BTS process. Corn cob and wood pellets were successfully tested in the unit for high purity syngas generation in extended test campaigns that totals over 200 hours. Syngas purity (H2 and CO) of >70% was achieved with a CH 4 concentration of <6%. The H 2 /CO ratio was greater than 1.8. A comprehensive techno-economic analysis was performed to compare the BTS process and a reference indirectly heated gasification process for methanol synthesis. The result, updated with experimental results for BTS process performance, shows a methanol required selling price (MSP) of $\$ $1.15/gal, compared to $1.28/gal for the reference case.

08 HYDROGEN↗
DOE OSTI2022

Solar-Thermal Ammonia Production: A Renewable, Carbon-Neutral Route to Ammonia via Concentrating Solar Thermochemistry [Slides]

Solar Thermal Ammonia Production has potential to produce green ammonia using CSP, air, and water. Air separation to purify N 2 was successfully demonstrated with BSF1585 in packed bed reactor; on-sun reduction reactor under construction. Metal nitrides (MNy) were successfully synthesized and characterized under both ambient and pressurized conditions. Co 3 Mo 3 N shown to successfully produce NH 3 when exposed to pure H 2 at pressures between 5 – 20 bar 600 – 750 °C. Ambient reaction experiments imply there may be a catalytic aspect as well. Technoeconomic and systems analyses show a path towards scale-up.

14 SOLAR ENERGY↗
DOE OSTI2023

Flexible Oxy-Fuel Combustion for High-Penetration Variable Renewables

A thermodynamic model was developed for the oxy-combustion Allam-Fetvedt cycle. This information was then used to develop an optimized dispatch strategy using price strips supplied by the modeling teams. The price strips represent future possible grid configurations that include a high penetration of variable renewables and a carbon tax. Multiple optimization strategies and tools were used to maximize the net present value (NPV) of the plant on these potential future grids. The optimization varied the size of the air separation unit, the size of oxygen storage tanks, the size of carbon dioxide storage tanks and the flow rate of the carbon dioxide pipeline. The team was able to determine a dispatch strategy that resulted in a positive NPV for all price strips. This indicates that an oxy-combustion plant with oxygen storage would be economically viable on a future grid with a high degree of variable renewables.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Aqueous-Based Granulation Method Towards Syngas Production

An aqueous-based granulation method is developed to combat the structural changes associated with binder-based granulation techniques. Microwave-assisted methane reforming studies showed an improved catalyst efficiency for these aqueous-based granules compared to the powder catalysts. This granulation method has been extended to other practical applications (chemical looping gasification and air separations).

aqueous-based granulation↗
DOE OSTI2021

Energy Arbitrage: Comparison of Options for use with LWR Nuclear Power Plants

Arbitrage is the opportunistic buying and selling of a commodity during local pricing valleys and peaks respectively to maximize economic value. This report evaluates options for energy arbitrage integrated with existing light water reactor (LWR) nuclear power plants (NPPs) where nuclear energy could be stored in a variety of forms and later recovered to generate electrical power during periods when grid electricity demand and pricing are high. The forms of energy storage examined in this report include the potential value of batteries, hydrogen, and thermal energy storage for coupling with nuclear power. Various large demand response options are also analyzed, including the production of liquid nitrogen via air separation and liquefaction, liquefaction of hydrogen, compressed hydrogen, and the cryogenic capture of CO2. Demand response refers to dispatchable loads that can cycle up or down depending on-grid electricity demand to aid in balancing the grid. Large demand response options could dispatch to aid nuclear power stations in avoiding power turndowns by providing an alternate disposition for electrical energy by producing marketable products (e.g., liquid nitrogen, hydrogen, or captured CO2). Static conditions were chosen and analyzed in this report for each option. Dynamic operation or optimization of energy arbitrage or demand response are out of scope for this report. The analysis is based on storage systems with discharge capacities of 500 MW for which various durations of storage and costs of charging (electricity cost) are examined. While the value of thermal energy to an industrial user for flexible plant operations has been previously proven as a business case, this report evaluates costs of hydrogen energy storage and leading thermal energy storage options, and large demand response loads that could be integrated with LWRs in comparison to utility-scale battery storage for use of off-peak nuclear energy. Compilation of this information will be used by the Idaho National Laboratory (INL) RAVEN/HERON systems integration and economics tool to evaluate thermal energy dispatch to industrial users. Relative ranking of energy storage options was done using a levelized cost of storage (LCOS) metric which calculates a rough breakeven cost for the system, taking into account the capital and operating costs as well as the revenue from arbitrage. Table ES1 below shows the LCOS for each of the energy storage options considered. First, in the table, lithium iron (Fe) phosphate batteries are listed as the base case for comparison against the other options. Next is hydrogen storage where most of the hydrogen analyses assumed the hydrogen to be produced using solid oxide electrolytic cell (SOEC) high temperature steam electrolysis (HTSE). The others used existing models of polymer electrolyte membrane (PEM) low temperature electrolysis to produce hydrogen. HTSE performance parameters and costs were taken from existing INL models. Various means were assumed to convert the hydrogen to electricity, including PEM fuel cells (FCs) and a gas turbine mixed in a 30 vol% mixture with natural gas. Physical storage (pressure vessels) and geological storage (natural underground features) were used to store the hydrogen as noted. Geological storage is more economical, but the locations are limited because of the requirement for pre-existing geological formations that will support storage. Thermal energy storage (TES) options were also analyzed including electro-thermal energy storage (ETES) and four different liquid sensible heat TES storage media as noted (Hitec, Hitec XL, Therminol-66, and Dowtherm A). The ETES process considered was modified using existing public documentation on an Echogen process and uses a separate supercritical CO2 charge and discharge cycle with sand as the heat storage media.

25 ENERGY STORAGE↗
DOE OSTI2023

Performance and Cost Potential for Direct-Fired Supercritical CO2 Natural Gas Power Plants

Direct-fired supercritical CO2 (sCO2) power cycles are being explored as an attractive alternative to natural gas combined cycle (NGCC) plants with carbon capture and storage (CCS). Therefore, understanding their performance and cost potential is important for the commercialization of the technology. This study presents the techno-economic optimization results of natural gas-fired, utility-scale power plants based on the direct sCO2 power cycle, which are lacking in public literature. To identify the optimum plant configuration, the study considered multiple cases with varying levels of thermal integration with the plant air separation unit (ASU). Several design variables for each power cycle configuration were identified and optimized to minimize the levelized cost of electricity (LCOE) for each case. The optimization design variables include the sCO2 cooler outlet temperatures, recuperator approach temperatures, and pressure drops. High fidelity models for recuperators, coolers, and turbines were developed and used to capture the impact of design variables on plant efficiency and capital costs. The optimization was conducted using a combination of manual sensitivity analyses and automated derivative-free optimization algorithms available under NETL’s Framework for Optimization and Quantification of Uncertainty and Sensitivity platform. The optimized direct sCO2 power plants offered similar or slightly higher plant efficiencies than the reference NGCC plants based on the F-class gas turbine with CCS. The LCOE of the optimized direct sCO2 plants is 13 to 17% higher than the reference NGCC plants with CCS due to high capital costs associated with the ASU and sCO2 power block, though there is significant room for improvement due to the high uncertainty in component capital costs for these new plants. Recuperators make up over 50% of the sCO2 power block costs. Consequently, any research and development efforts to reduce the recuperator capital costs will benefit the technology’s commercialization. The study also presents preliminary results showing the impact of co-firing landfill gas and natural gas on plant efficiency, LCOE, and CO2 emissions.

Pidaparti, Sandeep↗
DOE OSTI2023

Performance and Cost Potential for Direct-Fired Supercritical CO2 Natural Gas Power Plants

Direct-fired supercritical CO2 (sCO2) power cycles are being explored as an attractive alternative to natural gas combined cycle (NGCC) plants with carbon capture and storage (CCS). Therefore, understanding their performance and cost potential is important for the commercialization of the technology. This study presents the techno-economic optimization results of natural gas-fired, utility-scale power plants based on the direct sCO2 power cycle, which are lacking in public literature. To identify the optimum plant configuration, the study considered multiple cases with varying levels of thermal integration with the plant air separation unit (ASU). Several design variables for each power cycle configuration were identified and optimized to minimize the levelized cost of electricity (LCOE) for each case. The optimization design variables include the sCO2 cooler outlet temperatures, recuperator approach temperatures, and pressure drops. High fidelity models for recuperators, coolers, and turbines were developed and used to capture the impact of design variables on plant efficiency and capital costs. The optimization was conducted using a combination of manual sensitivity analyses and automated derivative-free optimization algorithms available under NETL’s Framework for Optimization and Quantification of Uncertainty and Sensitivity platform. The optimized direct sCO2 power plants offered similar or slightly higher plant efficiencies than the reference NGCC plants based on the F-class gas turbine with CCS. The LCOE of the optimized direct sCO2 plants is 13 to 17% higher than the reference NGCC plants with CCS due to high capital costs associated with the ASU and sCO2 power block, though there is significant room for improvement due to the high uncertainty in component capital costs for these new plants. Recuperators make up over 50% of the sCO2 power block costs. Consequently, any research and development efforts to reduce the recuperator capital costs will benefit the technology’s commercialization. The study also presents preliminary results showing the impact of co-firing landfill gas and natural gas on plant efficiency, LCOE, and CO2 emissions.

Pidaparti, Sandeep↗
DOE OSTI2024

Decarbonizing Hydrogen Production: Assessing A Net-Negative Pathway

Hydrogen is gaining prominence as a key factor in the world's transition to a cleaner energy future. The International Energy Agency (IEA)'s Global Hydrogen Review 2023 reports that the number of low-emission hydrogen production projects is increasing rapidly. The potential for growth in new applications such as heavy industry, transportation, and power generation is significant. The IEA urges more decisive action to spur demand for low-emission hydrogen to achieve climate goals. While hydrogen is produced through various industrial methods, each with its own advantages and disadvantages, low-carbon hydrogen is critical for mitigating climate change and is incentivized by the Clean Hydrogen Production Tax Credit (45V). To this end, we have evaluated a commercial technology that can produce low- or negative-carbon hydrogen via ethanol catalytic oxidative reforming. This study assessed life cycle greenhouse gas emissions (carbon intensity or CI) associated with the hydrogen production technology. A total of 24 scenarios were evaluated, encompassing (a) Gen1 versus Gen2 ethanol inputs, (b) carbon capture and sequestration (CCS) of upstream fermentation CO2, and (c) oxygen sourcing via air separation unit (ASU) versus purchased or on-site production of oxygen as a byproduct of hydrogen electrolysis with a proton exchange membrane (PEM). Key findings include that the base case CI for hydrogen production using Gen2 ethanol from corn stover is lower than Gen1 dry mill corn ethanol. The study also points out that the CI for hydrogen production using PEM-O2 is lower than that using ASU-O2, whether the PEM-O2 is produced on-site or off-site (importing). When sourcing oxygen from on-site PEM-O2, the Gen1 and Gen2 ethanol-derived hydrogen exhibit favorable net-negative CI values for all evaluated scenarios, especially if the upstream ethanol CCS is included. As a reference, the 45V regulatory threshold for generating clean hydrogen tax credits is a CI below 0.45 kg CO2e/kg hydrogen.

BIOMASS FUELS,HYDROGEN↗
DOE OSTI2023

High-Performance, Hybrid Polymer Membrane for Carbon Dioxide Separation from Ambient Air

The Department of Energy (DOE) seeks to develop carbon capture materials specifically tailored for Direct Air Capture (DAC) processes. Related to this, they require recipients to develop novel DAC materials such as: solvents, membranes, or sorbents that demonstrate high affinities or capacities for carbon dioxide (CO2) at concentrations typically available in air and at near ambient conditions. Toward this, InnoSense LLC (ISL) is developing High-Performance, Hybrid Polymer Membranes (HypoMemTM) for Carbon Dioxide Separation from Ambient Air. HypoMem consists of two major layers. The first layer is the active layer which contains the active ingredients that help to separate CO2 from ambient air. The second is the support layer that provides good mechanical support to have a free-standing membrane without interfering with the properties of the active layer.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Numerical analysis of air dehumidification through electrospray-enhanced vortical flow cyclone separator

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air significantly below its dew point temperature. Here, this study numerically investigates air dehumidification achieved by electrostatic and dielectrophoresis forces in a converging duct and centrifugal principles in cyclone separators. An electrospray was employed to energize water droplets, which then captured water vapor via dielectrophoresis. A novelty of the present study is the inclusion of a cyclone separator positioned downstream of the electrospray. This combination increased the dehumidification efficiency and controlled the flow of the condensate. By integrating electrospray technology and applying an electric field, this study examines the impact of particle separation efficiency, pressure drops, and cyclone performance on air dehumidification. The control parameters for air dehumidification were investigated. Three cyclones were modelled for airflow rates of 5 cubic feet per minute [cfm] (0.0024 m 3 /s), 38 cfm (0.0179 m 3 /s), and 200 cfm (0.094 m 3 /s). The results indicated air dehumidification was up to 5.7 % under environmental conditions, similar to those used to validate the CFD model. The degree of air dehumidification was primarily influenced by the electric charge acquired by the water droplets, their flight trajectory, and the vorticity intensity within the cyclone. Air dehumidification could increase by up to 13 % by increasing the number of droplets injected into the air stream, the flight time, and the electrical charge. The breakdown electric field strength threshold near the electrospray was a limiting factor for further enhancing dehumidification performance. This study examines the optimization of an electro-assisted dehumidification system that includes cyclone-based droplet separation through numerical analysis. The results provide insights into the design of energy-efficient air treatment technologies.

42 ENGINEERING↗