Characterizing the Efficiency of Perovskite Solar Cells and Light-Emitting Diodes
Not Available
14 SOLAR ENERGY↗
SEARCH · Engineering Papers
Results for “Solar cell characterization”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Decisive Structural and Functional Characterization of Halide Perovskites with Synchrotron
Not Available
36 MATERIALS SCIENCE↗
Voltage mapping and local defects identification in solar cells using non-contact method
Electroluminescence, infrared imaging, and current–voltage curve techniques are used to detect and map underperforming cells in a photovoltaic module or the modules in a photovoltaic string. In this work, we present a non-contact electrostatic voltmeter technique to detect and map the underperforming spots in a cell and the cells in a module. This non-contact technique directly maps the charged surface voltage (671mV) of the superstrate glass, and it had an 11-mV difference with the voltmeter values (660mV). Another data set of voltage values obtained by electroluminescence images conversion into a voltage map showed a difference of 7mV with the non-contact voltmeter values. Further, the direct voltage values obtained at various good and poor-performing spots of the cells using this technique are 3.69V and 3.79V and are validated using the voltage values obtained in electroluminescence analysis and the difference in voltage obtained by the two techniques is determined to be less than 2%. In this work, we combine the strengths of two complementary techniques of the electrostatic voltmeter (strength: quantitative) and electroluminescence (strength: spatial mapping) to obtain a quantitative spatial mapping of defects. Furthermore, this work is extendable to detect the poor-performing modules in solar PV power plants.
14 SOLAR ENERGY↗
Deep level transient spectroscopy and photoluminescence studies of hole and electron traps in ZnSnP 2 bulk crystals
ZnSnP 2 , an emerging inorganic material for solar cells, was characterized by deep level transient spectroscopy (DLTS) and photoluminescence (PL). Acceptor- and donor-like traps with shallow energy levels were detected by DLTS analysis. The previous study based on first-principle calculation also suggested such traps were due to antisite defects of Zn and Sn. PL measurements also revealed sub-gap transitions related to these trap levels. Furthermore, DLTS found a trap with a deep level in ZnSnP 2 . A short lifetime of minority carrier in previous work might be due to such trap, coming from phosphorus vacancies and/or zinc interstitials suggested by the first-principle study.
71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
Silicon solar cells from transition metal doped Czochralski and web crystals
The influence of metallic impurities on solar cell characteristics has been examined to establish the cost sensitive purity versus performance trade-offs. Solar cells were fabricated on 2 to 4 ohm-cm p-type substrates obtained by Czochralski and dendritic web growth processes. Controlled amounts of metallic impurities were introduced into the melt during growth and included Fe, Cr, Mn, Ni, Cu, Ti, V, Zr, Mg, Zn, and Al. Impurity concentrations in the crystals were determined using emission and mass spectrographic techniques and in some cases by neutron activation analysis. The solar cells were characterized by means of a computer program to curve-fit measured voltage-current data. The principal effect of the added impurities is a degradation of lifetime and diffusion length.
Davis, J. R.↗
Recent progress in high-output-voltage silicon solar cells
The status of the technology associated with the development of high output voltage silicon solar cells is reported. The energy conversion efficiency of a double diffusion process is compared to that of a single diffusion process. The efficiency of a 0.1 ohm/cm solar cell is characterized both before and after covering.
Muelenberg, A.↗
Characterization of HEM silicon for solar cells
The Heat Exchanger Method (HEM) is a promising low-cost ingot casting process for material used for solar cells. This is the only method that is capable of casting single crystal ingots with a square cross section using a directional solidification technique. This paper describes the chemical, mechanical and electrical properties of the HEM silicon material as a function of position within the ingot.
Dumas, K. A.↗
Material growth and characterization directed toward improving III-V heterojunction solar cells
In addition to the existing materials growth laboratory, the photolithographic facility and the device testing facility were completed. The majority of equipment for data acquisition, solar cell testing, materials growth and device characterization were received and are being put into operation. In the research part of the program, GaAs and GaA1As layers were grown reproducibly on GaAs substrates. These grown layers were characterized as to surface morphology, thickness and thickness uniformity. The liquid phase epitaxial growth process was used to fabricate p-n junctions in Ga(1-x)A1(x)As. Sequential deposition of two alloy layers was accomplished and detailed analysis of the effect of substrate quality and dopant on the GaA1As layer quality is presented. Finally, solar cell structures were formed by growing a thin p-GaA1As layer upon an epitaxial n-GaA1As layer. The energy gap corresponding to the long wavelength cutoff of the spectral response characteristic was 1.51-1.63 eV. Theoretical calculations of the spectral response were matched to the measured response.
Stefanakos, E. K.↗
InP concentrator solar cells
The design, fabrication, and characterization of high-performance, n(+)/p InP shallow-homojunction (SHJ) concentrator solar cells are described. The InP device structures were grown by atmospheric-pressure metalorganic vapor phase epitaxy. A preliminary assessment of the effects of grid-collection distance and emitter-sheet resistance on cell performance is presented. At concentration ratios of around 100, cells with efficiencies of 21.4 percent AM0 (24.3 percent direct) at 25 C are fabricated. These are the highest efficiencies yet reported for single-junction InP solar cells. The performance of these cells as a function of temperature is discussed, and areas for future improvement are outlined. Application of these results to other InP-based photovoltaic devices is discussed.
Ward, J. S.↗
Development of a new integral solar cell protective cover
A unique polyimide polymer has been developed which shows promise as an encapsulant for interconnected solar cell modules. Such an integral cover offers important weight and cost advantages. The polymer has been characterized on silicon solar cells with respect to electrical output and spectral response. The response of the material-coated cells to electron, low-energy proton, and vacuum-ultraviolet radiation, thermal shock and humidity tests was determined.
Naselow, A. B.↗
Characterizing Sustained Solar-to-Hydrogen Electrocatalysis at Low Cell Potentials Enabled by Crude Glycerol Oxidation
Unassisted solar-driven water electrolysis as a sustainable source for H 2 is limited by the high overpotential necessary to drive the oxygen evolution reaction (OER). Crude glycerol is an extremely alkaline byproduct of biodiesel synthesis that can be valorized or refined to produce more desirable chemicals. Glycerol can also be directly oxidized on an anode, replacing water oxidation, to reduce the applied cell potential requirements of electrolytic H 2 production or CO 2 reduction. An advantage of oxidizing glycerol in its crude form is the opportunity to valorize it without initial refinement. We describe an approach to replace the OER half-reaction with the sacrificial crude glycerol electrooxidation on a layered Au–Pt–Bi electrocatalyst on a Ni substrate. Compared to compositions with fewer components, the AuPtBi–Ni electrocatalyst improved the duration of performance and reduced the overall cell potential for glycerol electrooxidation in the extreme alkaline solutions representative of crude glycerol. These enhancements facilitated extended, unassisted hydrogen evolution from crude glycerol electrolysis, even under the power of a single-junction silicon solar cell at less than 1 sun illumination. We characterized the oxidation products of crude glycerol electrolysis and the subsequent products formed spontaneously in the electrolyte in the highly alkaline solution. This analysis helps to both identify the stoichiometric limits of glycerol oxidation at the low cell potentials of interest here and to understand the chemical control imparted by electrocatalysis on the ultimate compounds formed in the crude solution. Furthermore, the results for the AuPtBi electrocatalyst show that incorporating crude glycerol oxidation into integrated electrochemical systems can simultaneously simplify their design and significantly improve solar-to-hydrogen rates.
08 HYDROGEN↗
Laser-assisted solar-cell metallization processing
A photolytic metal deposition system using a focused continuous wave ultraviolet laser, a photolytic metal deposition system using a mask and ultraviolet flood illumination, and a pyrolytic metal deposition system using a focused continuous wave laser were studied. Fabrication of solar cells, as well as characterization to determine the effects of transient heat on solar cell junctions were investigated.
Dutta, S.↗
In-situ Characterizations of Microstructural Degradation of Perovskite Solar Cells
Rapid progress has been achieved in perovskite solar cells (PSCs), and their efficiencies have improved from 3.8 % to 24.2 % in less than a decade. With low-cost processing, PSCs have shown exciting photovoltaic (PV) properties, such as effective optical absorption, a long carrier lifetime, and unique defect tolerance. While recent studies demonstrated improved stability up to 100 days, PSC technology is still challenged to meet the stringent industry requirements for commercialization. Despite considerable efforts, the underlying physical mechanisms for the inferior stability of PSCs are not well understood. One reason for this divergence is that many established measurement techniques (e.g., quantum efficiency, photoluminescence) probe the properties on length scales far greater than that of electronic and/or structural inhomogeneity (i.e., < 1 μm near grain boundaries) and therefore characterize convoluted and/or averaged properties. Ion/electron beam-based techniques have been extensively used to access the microstructures of PSCs, enabling atomic/nanoscale structural, chemical, optical, and electrical characterizations. For example, focused ion beam (FIB) milling produces an atomically smooth surface that minimizes the artifacts attributed to the surface roughness. FIB techniques can also create a well-defined cross-section of PSCs without mechanical damage in a physical cleaving sample preparation. While powerful, there are some concerns about possible beam damage of inorganic-organic perovskites via chemical-bond breakage and local heating. This project aims to comprehensively understand how the microstructural/interfacial properties of PSCs (e.g., Methylammonium Lead Iodide [MAPbI 3 ]) are modified under the irradiating ion beams. Specifically, we investigate the sub-surface properties of PSCs before and after Ar-ion beam injections. Kelvin probe force microscopy (KPFM) measures the contact potential differences (CPDs). Photoluminescence (PL) microscopy in conjunction with Finite-Difference Time-Domain (FDTD) simulations infers the formation of a “dead layer” (< 15 nm) on the subsurface of MAPbI 3 during Ar+ milling processes while preserving the initial bulk properties. The x-ray photoemission spectroscopy (XPS) confirms this modified surface is a lead-rich and iodine-deficient surface. We initiate customizing in-situ measurement setup while measuring the local optical and electrical properties of PSC under thermal (cooling, heating) and light stressors. Our results provide in-depth knowledge of the ion-beam impact on metal-halide perovskites and how this modified sub-surface impacts their properties under accelerated stressors of light and heat. Intensive Monte Carlo simulations of an electron beam interacting with PSCs provide the beam energy distribution in PSCs, proposing possible measurement conditions of using e-beam with minimizing beam damage. Our in-situ measurement platform can accommodate the diverse architecture of PSC devices for studying deterioration mechanisms under mixed environmental stressors.
14 SOLAR ENERGY↗
Characterization of three types of silicon solar cells for SEPS deep space missions. Volume 1: Current-voltage characteristics of OCLI BSF/BSR 10 ohm-cm, and BSR 2 ohm-cm cells as a function of temperature and intensity
Three types of high performance silicon solar cells, BSF/BSR 10 ohm-cm, BSR 10 ohm-cm, and BSR 2 ohm-cm, were evaluated for their low temperature and low intensity performance. Sixteen cells of each type were subjected to ten temperatures and nine intensities. The BSF/BSR 10 ohm-cm cells provided the best performance at 1 solar constant and +25 C with an efficiency of 14.1% while the BSR 2 ohm-cm cells had the highest low temperature and low intensity performance with an efficiency of 22.2% at 0.04 solar constant and -170 C and the most consistent cell-to-cell characteristics.
Whitaker, A. F.↗
Characterization of three types of silicon solar cells for SEPS deep-space missions. Volume 2: Current voltage characteristics of Solarex textured P(+)8 to 10 mil, planar P(+)8 to 10 mil and planar P(+)2 mil cells as a function of temperature and intensity
Three types of high performance silicon solar cells, textured P(+)8 to 10 mil, planar P(+)8 to 10 mil and planar P(+)2 mil were evaluated for their low temperature and low intensity (LTLI) performance. Sixteen cells of each type were subjected to 11 temperatures and 9 intensities. The textured P(+)8 to 10 mil cells provided the best performance both at 1 astronomical unit and at LTLI conditions. The average efficiencies of this cell were 14.5 percent at 1 solar constant/+25 C and 18.7 percent at 0.086 solar constant/-100 C.
Whitaker, A. F.↗