Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite Technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 91 records · Page 5
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Development of Ti 3 SiC 2 MAX phase tubular structures for solar receiver applications

Solar receiver tubes are key components of concentrating solar-thermal power (CSP) systems that harvest solar energy. For better efficiency, the Gen3 CSP receivers, which collect heat into a heat transfer fluid, require a temperature exceeding 700 °C during operation and need to perform under extreme conditions of high temperature and high thermal stress. Operators are seeking CSP designs using new high-temperature structural materials with high thermal conductivity and high creep resistance to achieve a design life of 30 years and thus help recover the plant capital cost sooner. MAX phase materials, which consist of an early transition metal element, an A-group element, and carbon or nitrogen, are expected to exhibit high creep resistance as well as high fracture toughness. Here, in this paper, we describe fabricating both (1) dense Ti 3 SiC 2 MAX phase disks and (2) short-length tubes using field-assisted sintering technology (FAST). First, the disk samples that we fabricated are fully dense and contain ≈90 % Ti 3 SiC 2 MAX phase materials and ≈10 % TiC phase materials. We determined a flexure strength of 519 ± 32 MPa by conducting a four-point bending test at room temperature with rectangular bar samples of ≈100 % density. The thermal conductivity of the Ti 3 SiC 2 MAX phase samples, measured by light flashing analysis, decreases linearly from a value of 41 W . m -1 . K -1 at room temperature to a value of 36 W . m -1 . K -1 at 650 °C. A solar reflectance measurement of the Ti 3 SiC 2 MAX phase revealed that, temperature increases from 400 to 1400 °C, thermal emittance increases from 0.39 to 0.49, while selectivity decreases from 1.8 to 1.4, respectively. Whereas the surface oxidized MAX phase samples after 100 h exposure to air at 1000 °C exhibit that of SiC. Next, we discuss fabrication of the crack-free Ti 3 SiC 2 MAX phase tubular structures accomplished by using FAST processing in graphite bedding. A Ti 3 SiC 2 MAX phase content of > 95 % with traceable ≈3% remaining TiC phase and ≈15 % porosity were demonstrated after high-temperature annealing. An average fracture strength of ≈250 MPa was determined with Ti 3 SiC 2 MAX phase tubes of ≈85 % density by diametral compression testing at room temperature. Our work demonstrated that using FAST processing to produce Ti 3 SiC 2 MAX phase tubular structures for CSP receiver applications is a viable approach.

14 SOLAR ENERGY↗
DOE OSTI2025

Non-destructive structural characterization of graphite components using mechanical resonance and deep learning

As compared to conventional nuclear reactors, microreactors have the potential to significantly reduce construction timelines and capital costs, decreasing the barriers for advanced nuclear reactor technologies. However, the lower power output of these microreactors (typically < 20 MWe) creates challenging economics if operation and maintenance costs cannot be sufficiently reduced. The compact size of these designs presents an opportunity for comprehensive in-situ structural health monitoring to provide real-time feedback in order to reduce operational costs associated with maintenance and downtime. Many microreactor concepts use graphite for both in-core neutron moderation and as a structural material, which has typically required some form of periodic and laborious inspection. This report provides a description and assessment of recent work with graphite to couple acoustic-based experimental measurements and characterization with machine learning models to mature structural health monitoring capabilities and generate benefits for the nuclear microreactor industry. With resilient embedded sensors in development in other programs funded by the US Department of Energy’s Office of Nuclear Energy and elsewhere, the work described herein builds upon previously funded efforts to mature non-destructive testing technology that relates measured vibrational signatures to structural changes, using a combination of new experimental measurements and machine learning processing. Building on past successful demonstrations of predictive workflows to identify structural changes in a hexagonal stainless steel test article with excellent acoustic propagation, we first performed baseline characterization on graphite samples with canonical geometries to ensure compatibility and confidence in the applied techniques for a material with distinctly different mechanical properties. In contrast to efforts in previous years, we worked exclusively with unidirectional vibration data that is more comparable to those expected from the existing embedded sensor technologies which are suitable for deployment in a reactor setting. Established acoustic and modern machine-learning-based characterization approaches were applied to the resulting datasets from these simple geometries. Both approaches were found to be highly capable of detecting even small geometric irregularities amongst nominally identical samples. As such, we then moved to testing these approaches for detection of artificial local stress perturbations introduced into a more complex geometry: a hexagonal block with drilled holes. A main outcome of this work is that a generalizable ML workflow can be used to detect and predict the characteristics of small artificial anomalies in a graphite component with a relevant geometry. While this work was performed using surficial vibration data, we expect the approach to be flexible and viable for other monitoring scenarios, such as those with different arrangements or types of sensor arrays. As compared to previously funded efforts, an existing ML workflow based on neural networks was enhanced through the addition of recently developed Fourier neural operators. As applied to previously collected and new vibration datasets, prediction accuracies of anomaly characterizations were greatly improved with minimal added computational cost. As trained on small durations of vibration data (tens of seconds) collected over a realistic number of locations, the model was able to reliably determine the presence of a subtle stress anomaly and begin to provide location estimates. Such an approach is likely to be viable for more relevant reactor damage scenarios for graphite components, such as progressive crack growth or creep.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A Comprehensive Experimental Study on Microstructure‐Graded Graphite Anodes for Enhancing Fast‐Charging Capability of Lithium‐Ion Batteries

Lithium‐ion batteries with high gravimetric capacity density and improved cycle life performance under fast‐charging conditions are crucial for widespread electric vehicle (EV) adoption. This study investigates how designing graphite anode microstructure, specifically porosity, and particle‐size gradients, improves lithium‐ion (Li + ) transport during fast‐charging conditions. Three‐layered graphite anodes with varying porosity (24%, 36%, 46%) and particle size gradients (3, 5, 10 μm) were compared to a conventional single‐layered electrode in half‐cell configurations. At room temperature and high discharge rate (2C), both gradient structures showed significantly enhanced capacity retention (80% and 67% vs. 50%) compared to the conventional electrode, highlighting the effectiveness of microstructure engineering for fast charging. The study also investigated the temperature's impact on cycle life. After 200 cycles at 2°C and 45°C, all gradient structures demonstrated superior capacity retention (≈80%) compared to the conventional electrode (35%), suggesting the gradients mitigate degradation rate at high temperatures. Electrochemical impedance spectroscopy confirmed superior Li+ diffusion and lower resistivity in gradient electrodes. Simulations explored the influence of gradient profiles on reaction kinetics across the electrode thickness. Overall, this research demonstrates that the fast‐charging capability of graphite electrodes can be greatly enhanced by engineering the electrode microstructure, thereby making EV technology more accessible and appealing.

Ahmadi, Soma↗
DOE OSTI2025

Upcycling Polyethylene Waste Into Hybrid Graphitic Porous Carbon Materials Used in High-Performance Zinc-Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, we report a chemical process that addresses this challenge by converting mixtures of linear low-density polyethylene (LLDPE), low-density polyethylene (LDPE), and high-density polyethylene (HDPE) waste into a hybrid graphitic porous carbon (HGPC) that can be used as a zinc-ion hybrid capacitor cathode. The process uses a low temperature thermal oxidation pre-treatment step, with assistance of an inert solid additive (KCl) to increase the effective surface area of the PE melt, to functionalize, cross-link, and stabilize the PE waste followed by carbonization and catalytic graphitization steps at higher temperatures with a potassium carbonate (K2CO3) catalyst. The PE waste derived HPGC (PW-HPGC) has a hybrid structure composed of graphene-like carbon nanosheets grown on the surface of carbon particles, high porosity with the Brunauer–Emmett–Teller (BET) specific surface area up to 1,763 m2g-1, and good graphitic degree with average Raman I2D/IG ratios of 0.53. When used as a cathode material for zinc-ion hybrid capacitors, this PW-HGPC exhibits an excellent specific capacity up to 126.7 mAhg-1 at high mass loading of 10 mgcm-2. Moreover, PW-HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10,000 cycles at a current density of 2.0 A g-1.

hybrid graphitic porous carbon↗
DOE OSTI1989

Nuclear Safety [Vol. 30, No. 3, July-September 1989]

Nuclear Safety is a review journal that covers significant developments in the field of nuclear safety. Its scope includes the analysis and control of hazards associated with nuclear energy, operations involving fissionable materials, and the products of nuclear fission and their effects on the environment. Primary emphasis is on safety in reactor design, construction, and operation; however, the safety aspects of the entire fuel cycle, including fuel fabrication, spent-fuel processing, nuclear waste disposal, handling of radioisotopes, and environmental effects of these operations, are also treated. Table of Contents for this issue follows. GENERAL SAFETY CONSIDERATIONS: 325 Safety of Framatome Advanced Nuclear Steam Supply Systems Designs by J. A. Charles and D. Lange, 333 Book Review of Nuclear Accidents: Intervention Levels for the Protection of the Public by H. B. Piper; ACCIDENT ANALYSIS: 335 Living PRA Computer Systems by S. C. Dinsmore and H.-P. Balfanz, 343 Summary of ICAP Assessments of RELAP5/MOD2 by W. E. Driskell and R. G. Hanson; CONTROL AND INSTRUMENTATION: 352 Thermal Performance Monitoring System at Maanshan Nuclear Power Plant by H.-J. Chao, Y.-P. Lin, G.-H. Jou, L.-Y. Liao, and Y.-B. Chen; DESIGN FEATURES: 358 Warning Systems for Nuclear Power Plant Emergencies by J. H. Sorensen and D. S. Mileti; WASTE AND SPENT FUEL MANAGEMENT: 371 Activities Related to Waste Management Compiled by E G. Silver; OPERATING EXPERIENCES: 382 Steam Generator Tube Performance: Experience with Water-Cooled Nuclear Power Reactors During 1985 by O. S. Tatone and R. L. Tapping, 400 Systems Interaction Analyses: Concepts and Techniques (Part II) by M. D. Muhlheim and G. A. Murphy, 413 Reactor Shutdown Experience Compiled by J. W. Cletcher, 416 Operating U.S. Power Reactors Compiled by E G. Silver; RECENT DEVELOPMENTS: 440 General Administrative Activities Compiled by E G. Silver, 460 Reports, Standards, and Safety Guides by D. S. Queener, 466 Status of Power-Reactor Licensing Activities Compiled by E G. Silver, 470 Proposed Rule Changes as of Mar. 31, 1989; ANNOUNCEMENTS: 334 Proceedings Published, 351 CEC Seminar on Methods and Codes for Assessing the Off-Site Consequences of Nuclear Accidents, 357 Short Course on Multiphase Flow and Heat Transfer: Bases and Applications in A: The Nuclear Power Industry B: The Process Industries, 357 International Conference on Probabilistic Safety Assessment and Management, 478 International Topical Meeting on the Safety, Status, and Future of Non-Commercial Reactors and Irradiation Facilities, 475 The Authors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Europium diffusion in IG-110 nuclear graphite

Europium diffusion in graphite has been recognized to be of interest in high-temperature gas reactor safety analysis, particularly as an indicator of strontium diffusion. However, no measurements of europium diffusion coefficients have been reported in the literature. In this work, the effective diffusion coefficient of europium was measured using a time-release method. Natural europium was loaded into pre-milled unirradiated IG-110 graphite spheres using a pressurized acid digestion vessel. The time-release experiments were performed in the temperature range 1823 K – 1973 K using a SiC diffusion cell connected to an inductively-coupled plasma mass spectrometer (ICP-MS) via a He gas line. Finally, the results of this work are: D Eu, IG-110 = (1.5 x 10 -3 m 2 /s) exp $(\frac{-2.87\mathrm{x}10^{5} J/mol}{RT})$ This effective diffusion coefficient can be used to aid in predictive modelling of europium transport in HTGRs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Synthesizing Highly Crystalline Graphite Powder from Bulk Polyethylene Waste for Lithium-Ion Battery Anodes

Upcycling plastic waste into graphite can potentially be used, in conjunction with other methods, to manage existing waste materials and diversify graphite supply chains. However, synthesizing large quantities of crystalline graphite powder from plastic waste, particularly polyethylene (PE), remains a challenge because PE decomposes into light gases during thermal processing, and simple methods do not exist at any appreciable size scale to address this challenge. In this work, a method is developed for air processing bulk forms of PE waste to create a stable carbon char that does not readily decompose during high-temperature processing. This method employs solid additives in the form of salts, which are combined with the PE melt during air processing to increase the effective surface area of the melt and improve the oxygen-driven chemistry that stabilizes the PE for high-temperature processing. After removing the solid salt additives from the PE-derived char, it is converted into a highly crystalline bulk graphite powder using a Fe-based low-temperature (<1500 °C) catalytic process. The PE-derived graphite powder showed excellent electrochemical performance as an anode material for lithium-ion batteries (LIBs) with a capacity of up to 302 mAh/g at 0.5 discharge/charge cycles per hour (0.5 C) and capacity retention of 100% after 415 cycles. This method illustrates there are opportunities for upcycling large quantities of PE waste to produce graphite powders.

Huynh, Ngoc Tien [NETL Site Support Contractor, Na↗
DOE OSTI2023

NanoMechanics: Elasticity and Friction in Nano‐Objects

A large scientific and technological effort is underway to investigate the properties of two‐dimensional (2D) materials to become building blocks in integrated nano‐electronic and photonic circuits, composites, coatings, energy harvesting nano‐ systems, nano‐sensors, and nano‐electro‐mechanical systems (NEMS).While several experiments and calculations have revealed exciting novel phenomena in these nanostructures, many scientific and technological questions remain open. In particular, understanding and controlling the structure and mechanical properties of 2D materials at the interface with a solid surface is of key importance to enable the aforementioned nanotechnologies, as well as to fulfill the potential of strain engineering to tailor their properties. The vision of this DoE research program was to investigate novel mechanical properties and phenomena in 1D and 2D materials with the overarching goal of defining a new basic understanding of mechanical behavior in nano and quantum systems. The group of the PI has developed in the last years several studies on the mechanical properties of Carbon nanotubes and oxide nanobelts, more recently the PI has focused her attention on the properties of two‐dimensional materials, such as graphene and MoS 2 , which are a few‐atomic‐layer thick films and hold a great potential for technological and energy applications. The most studied 2D material is graphene, existing as a single layer of graphite or a few‐layer thick epitaxial graphene film. Graphene possesses a large in‐plane Young’s modulus as well as high intrinsic carrier mobility, and high in‐plane thermal conductivity. Besides graphene, also 2D films of graphene oxide (GO), hexagonal Boron Nitride (h‐BN), and transition metal dichalcogenides such as MoS 2 exhibit unique and excellent properties and hold great promise for nanotechnology applications. This research program was aimed at developing a new basic understanding of the mechanical properties of 1D and 2D materials at the interface with solid substrates, with a focus on the role of defects, materials structure, and substrate interaction. Ultimately, we aimed at developing the basic knowledge and experimental tools for manipulating 1D and 2D materials’ structure, stacking, substrate interaction, defects, and number of layers to realize an entirely new class of ultra‐hard, ultra‐thin, and ultra‐light active materials with ad‐ hoc mechanical properties for a variety of applications.

2D Materials↗
DOE OSTI2025

Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.

hybrid graphitic porous carbon↗
DOE OSTI2024

Production of Carbon Nanomaterials and Sorbents from Domestic U.S. Coal (Final Report)

The main goal of this project was to produce high-value carbon nanomaterials and carbon sorbents from domestic coal resources in a cost-effective manner. Four types of domestic coal samples were processed through a combination of deashing, devolatilization, oxidation, reduction, and activation treatments to produce graphene oxide (GO), reduced graphene oxide (RGO), and activated carbon (AC). The precursors and developed materials were extensively characterized by various methods to investigate the impact of the coal feedstock type on the yield and quality of each product. A commercial graphite-based GO sample was included in the experimental work as the baseline material for comparison with the coal-based materials developed in this work. The performed work also included a technoeconomic analysis and cost estimation for a plant processing 20 tons/day coal, a market evaluation for the graphene materials, and a technology gap analysis. A simple process by concentrated nitric acid oxidation is used to oxidize coal precursors for the production of GO. Fine oxidized coal particles that were separated from larger oxidized coal particles had significantly higher oxygen contents and were identified as coal-based GO samples. Coarse oxidized coal particles were used as precursors for production of AC. Based on the Raman spectroscopy results, coal-based GO samples exhibited G and D bands similar to those of graphite-based GO samples. X-ray photoelectron spectroscopy revealed that coal-based GO samples had surface oxygen contents of ~26-35% that were higher than the oxygen contents of graphite-based GO samples. Larger particles of oxidized coal samples were activated under different conditions to produce high surface area functionalized AC. Prepared materials had surface areas exceeding 1,500 m 2 /g and pore volumes more than 1 cm 3 /g with different pore size distributions. Reduced graphene oxide samples were prepared by thermal reduction of both coal-based and graphite-based GO samples at 170-2800 ºC. Coal-based and graphite-based RGO samples exhibited similar carbon contents, Raman spectra, and XRD profiles. Heat treatment above 1500 ºC shifted RGO to synthetic graphite. Among anthracite, bituminous, subbituminous, and lignite coals tested, anthracite was the best precursor to produce carbon nanomaterials exhibiting properties similar to those of graphite-based materials. Anthracite-based carbon nanomaterials also had the highest production yields. Technoeconomic analysis estimated the production cost of GO and RGO for anthracite-based samples at about 2,600 and 4,200 $/ton, respectively, which is about two orders of magnitude lower than the current estimated price of graphite-based materials. Several gaps to further develop the proposed technology were identified and discussed that include process and equipment optimization, process integration, need for additional bench- and pilot-scale experiments, and other items to reduce the scale up risk. Market analysis reports suggested a compound annual growth rate of 40% for graphene and related materials. Short-term applications include composites, inks, and coatings. However, energy storage applications appear to be the dominant potential long-term applications. Different applications of coal-based GO and RGO need to be explored and clear metrics and standards for each application need to be developed.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

A cradle-to-grave life-cycle-assessment of dry-processed Li-ion batteries for electric vehicles

Maxwell-type dry processing has emerged as a promising manufacturing technology for high-areal-loading Li-ion battery electrodes, offering a significant advantage by eliminating the use of the toxic and costly NMP solvent. This study developed a cradle-to-grave life-cycle-assessment model to evaluate the environmental impacts of this innovative technology, benchmarking the results against the conventional NMP-based technique for a configured 42 kWh NMC622-graphite battery pack. Furthermore, the findings reveal that the dry-processing method merits a 4.8% lower energy consumption and achieves environmental impacts up to 47.5% lower in 12 out of 13 categories, highlighting its environmental benefits compared with the NMP-based manufacturing processes.

Electrode↗
DOE OSTI2025

Enabling hydrogen chemisorption on charged graphene

Two-dimensional (2D) materials, including graphitic derivatives, have long been of interest for hydrogen storage applications, due to their high theoretical storage capacity, low weight, and other useful properties. However, poor kinetics for hydrogen adsorption and surface diffusion as part of the proposed spillover process for hydrogenation have limited their technological potential. Here, we use first-principles calculations to study electronic doping as a means to improve hydrogen chemisorption on graphene, which we use here as a proxy for graphitic derivatives more broadly. We find that positively charged graphene sheets have vastly improved kinetics for hydrogen diffusion and adsorption, while they limit unwanted hydrogen desorption. This combination of effects should favor hydrogen chemisorption via spillover. We connect these trends to the C–H bond, which introduces states near the Fermi level. These states are depopulated as electrons are removed, thereby lowering the bond energy and permitting more facile movement of hydrogen. Our results suggest that spillover mechanisms for hydrogen chemisorption should be revisited if strategies to apply a large charge to graphitic systems can be realized. Moreover, switchable application of the charge may lead to the reversible chemisorption of hydrogen. While the large magnitude of charging required suggests that graphene itself may not be suitable for reversible hydrogen chemisorption, the factors we identify and discuss could significantly boost the prospects of graphitic derivatives and other 2D or layered materials for hydrogen storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Horizontal Split Table Conceptual Design for Advanced Reactor Validation

Oak Ridge National Laboratory and Lawrence Livermore National Laboratory are collaborating to develop a conceptual design for a horizontal split table for use in performing critical experiments. The goal of this design effort is to provide nuclear data testing and validation capabilities for advanced reactors such as pebble-bed high-temperature gas-cooled reactors, molten salt reactors, and heat pipe microreactor, but it could also be used for the current generation of reactors. The first concept being explored for the horizontal split table, a pebble-bed design based on the HTR-10 reactor, is described in this paper. A critical configuration corresponding to a footprint of about 4.5 m 2 was determined with SCALE/KENO-VI to fit the planned dimensions of the horizontal split table. The similarity of the pebble-bed design and the HTR-10 reactor application was assessed using SCALE/TSUNAMI, and a similarity coefficient $c_k$ of 0.9982 was obtained, proving that the concept will be useful for nuclear data validation and assimilation of pebble-bed type advanced reactors. In the proposed design, the materials with the highest $k_{eff}$ sensitivity are graphite and uranium, demonstrating that particular care must be given to carbon-related cross-section data. The effect of mechanical uncertainties between the fixed and moving tables was also assessed by calculating the reactivity change caused by vertical and horizontal gaps, as well as angular and torsion offsets between the two sides of the horizontal split table concept. The highest relative changes on the concept’s reactivity were caused by angular perturbations. The same analysis process is currently being used to create a molten salt advanced reactor type horizontal split table concept based on the Molten Salt Reactor Experiment (MSRE).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Use of Constrained Gamma Emission Computed Tomography to Evaluate Fission Product Distributions in High-Temperature Materials from a TRISO Fuel Irradiation

An image reconstruction technique was developed to overcome problems with earlier methods of gamma emission computed tomography of graphite rings surrounding the AGR-3/4 TRISO fission product transport experiment. The profiles obtained from the tomography are compared with sampling done via radially resolved destructive sampling techniques. Generally, there is good agreement between profiles measured via destructive sampling of the rings and the tomographic profiles, though at low signal strengths, the tomographic profiles appear elevated.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Interfaces in all solid state Li-metal batteries: A review on instabilities, stabilization strategies, and scalability

With technological advancements in electrochemical energy storage systems increasing at a spectacular rate, batteries equipped with a lithium anode hold the key towards unlocking high energy densities. While lithium-ion batteries with layered anodes (e.g. graphite) and liquid organic electrolytes have been ubiquitous in portable electronics, electric vehicles, and grid applications, all solid-state batteries that use the combination of a lithium anode and a solid-state electrolyte (SSE) will further advance the present technology. The underlying challenge that limits the successful development of all solid-state batteries (ASSBs) is dictated largely by the highly reactive interfaces at the anode/SSE and the cathode/SSE interface. In this comprehensive review, we present an overview of the following: (i) characterization of the electrode/SSE interface via multimodal characterization, which include X-ray-, electron-, neutron-, optical-, and computation-based methods: (ii) parasitic reactions that occur from chemical, mechanical or electrochemical instabilities and interfacial engineering strategies for improving the stability of these interfaces classified by the class of inorganic SSEs (sulfide-, NASICON-, and garnet-type SSEs); (iii) laboratory-to-industry scale processing perspectives of SSEs; (iv) scalability and manufacturing aspects of current interfacial strategies; and (v) the prospects of all ASSBs within the context of extreme fast charging capability. Here, this review seeks to highlight key efforts in the field of ASSBs, by focusing particularly on stabilizing the electrode/SSE interfaces, which will help to bridge fundamental studies to technological relevance.

25 ENERGY STORAGE↗
DOE OSTI2020

Analytical model of low and high ablation regimes in carbon arcs

Graphite ablation by an electric arc or a laser/solar flux is widely used for the synthesis of carbon nanomaterials. Previously, it was observed in multiple arc experiments that the ablation rate is a strong nonlinear function of the arc current and it drastically increases at some threshold current. As such, we developed an analytical model explaining this transition in the rate of ablation by an electric arc or a laser/solar flux. The model not only explains the observations but can also accurately predict the experimentally observed ablation rates. The model takes into account redeposition of carbon back to the ablated surface, which is the key process responsible for the observed effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Measurement of Helium and Xenon Knudsen permeability in graphite IG-11

Here, understanding the flow and diffusion (transport) of gases through nuclear graphite is of interest in both the prismatic and pebble bed high-temperature gas reactors (HTGRs), for normal operation and under accident conditions, for example, as related to graphite oxidation. Both the laminar and turbulent gaseous transport are of interest. It has also been noted that nuclear graphite can have pore sizes that can possibly lead to non-continuum transport, as the pore size can be comparable to the gaseous mean free path. We report measurements and analyzes of experiments performed with IG-11 graphite in the pressure range of 10 Pa to 14,700 Pa, 293 K, using Helium, and research grade xenon (99.999%), respectively. These values are in fair agreement with those reported for different graphites and gases by other investigators, but are also higher by six orders of magnitude than those reported for Kr permeability in a developmental very low permeability graphite-HXT-90. Our measured ratio of the Helium and Xenon permeabilities is about 4, different from $\sqrt{\frac{m_{Xe}}{m_{He}}}$ ≈ 5.72 that corresponds to diffuse reflection at the graphite surface for both gases. Simple analysis indicates that the two gases have slightly different accommodation coefficients (about 25%) with the graphite surface. However, there could also be other reasons, such as experimental uncertainties or the need for a more detailed analysis.

36 MATERIALS SCIENCE↗