Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 883 records · Page 49
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Effect of thickness on degradation of austenitic 347H steel by direct-fired supercritical CO 2 power cycle environment

Austenitic 347H steel of two thicknesses (2.54 and 0.6 mm) was exposed to a simulated direct-fired supercritical CO 2 (sCO 2 ) power cycle environment at 650°C and 1 atm for 1000 h then tensile stressed at room temperature to study the deformation behavior. The thicker 347H formed a protective chromia scale over most of the surface, which minimized carburization of the underlying steel and resulted in no change in mechanical performance. In stark contrast, the thinner 347H formed non-protective Fe-rich oxides over the entire surface, resulting in extensive carburization of the underlying steel. Finally, this led to increased strength but significantly reduced ductility, resulting in partially brittle failure

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manipulating Surface Termination of Perovskite Manganate for Oxygen Activation

For ABO 3 perovskite oxides, one of the key issues limiting their utilization in heterogeneous catalysis is the dominant presence of catalytically inactive A-site cations at the surface. The engineering of B-site terminated perovskites is considered as an effective method to address this issue, especially when dealing with Mn/Co-based perovskite catalysts. However, to date, such a strategy has not been fully successful and remains a major challenge in the field. Herein, a Mn-terminated La 0.45 Sr 0.45 MnO 3 (B-LSM) is successfully synthesized via a one-pot hydrothermal method, in which low-valence Mn ions partially occupy the A site to form the active Mn-excess phase. Additionally, experimental results and theoretical calculations reveal that the presence of the surface Mn termination in B-LSM optimizes the hybrid orbitals of Mn 3d-O 2p and promotes the activation of surface lattice oxygen, where the pristine inert lattice O 2- is evolved into active and stable lattice O 2-x . Such structural optimization significantly reduces the activation energy barriers on going from O 2 ⁻ species to important intermediate O - species during O 2 activation. Moreover, this results in good stability and Pt-like activity for the B-LSM during CO oxidation. This work offers a new chemical route for the design of advanced perovskite-type oxides possessing novel functions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fabrication of anodic aluminum oxide on silica optical fiber with nanopore channels oriented off surface normal

Abstract Aluminum coating on silica optical fiber was anodized by applying an electric field off‐axis to surface normal of the fiber coating with simulation of the electric field lines between angularly positioned anode and cathode as a guide. The nanostructure features, including nanopore orientation, of the resultant anodized aluminum oxide (AAO) were characterized using scanning electron microscopy. This unique off‐axis electric field arrangement enabled the formation of AAO with uniformly tilted nanopore channel arrays. Nanopore channels with tilting angles around 10°–20° relative to surface normal of AAO were obtained. These results are in general agreement with the simulated electric field lines between the anode and cathode.

Materials Science↗
DOE OSTI2020

Interfacial and Activation Energies of Environmentally Abundant Heterogeneously Nucleated Iron(III) (Hydr)oxide on Quartz

Poorly crystalline iron(III) (hydr)oxide nanoparticles are ubiquitous in environmental systems and play a crucial role in controlling the fate and transport of contaminants. Yet, the thermodynamic and kinetic parameters, e.g., the effective interfacial (α^') and apparent activation (E a ) energies, of iron(III) (hydr)oxide nucleation on earth-abundant mineral surfaces have not been determined, which hinders an accurate prediction of iron(III) (hydr)oxide formation and its interactions with other toxic or reactive ions. Here, for the first time, we report experimentally obtained α^' and E a for iron(III) (hydr)oxide nucleation on quartz mineral surfaces, by employing a flow-through, time-resolved grazing incidence small angle X-ray scattering (GISAXS). GISAXS enabled the in situ detection of iron(III) (hydr)oxide nucleation rates under different supersaturations (σ, achieved by varying pH 3.3-3.6) and temperatures (12-35ºC). By quantitative analyses based on classical nucleation theory, α^' was obtained to be 34.6 mJ/m 2 and E a was quantified as 32.8 kJ/mol. The fundamental thermodynamic and kinetic parameters obtained here will advance our fundamental understanding of the surface chemistry and nucleation behavior of iron(III) (hydr)oxides in subsurface and water treatment systems, as well as their effects on the fate and transport of pollutants in natural and engineered water systems. The in situ flow-through GISAXS method can also be adapted to quantify thermodynamic and kinetic parameters at interfaces for many important solid–liquid environmental systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pathways for methane emissions and oxidation that influence the net carbon balance of a subtropical cypress swamp

We evaluated the major pathways for methane emissions from wetlands to the atmosphere at four wetland sites in the Big Cypress National Preserve in southwest Florida. Methane oxidation was estimated based on the d13C-CH4 of surface water, porewater, and bubbles to evaluate mechanisms that limit surface water emissions. Spatially-scaled methane fluxes were then compared to organic carbon burial rates. The pathway with the lowest methane flux rate was diffusion from surface waters (3.50 ± 0.22 mmol m-2 d-1). Microbial activity in the surface water environment and/or shallow oxic sediment layer oxidized 26 ± 3% of the methane delivered from anerobic sediments to the surface waters. The highest rates of diffusion were observed at the site with the lowest extent of oxidation. Ebullition flux rates were 2.2 times greater than diffusion and more variable (7.79 ± 1.37 mmol m-2 d-1). Methane fluxes from non-inundated soils were 1.6 times greater (18.4 ± 5.14 mmol m-2 d-1) than combined surface water fluxes. Methane flux rates from cypress knees (emergent cypress tree root structures) were 3.7 and 2.3 times higher (42.0 ± 6.33 mmol m-2 d-1) than from surface water and soils, respectively. Cypress knee flux rates were highest at the wetland site with the highest porewater methane partial pressure, suggesting that the emergent root structures allow methane produced in anaerobic sediment layers to bypass oxidation in aerobic surface waters or shallow sediments. Scaled across the four wetlands, emissions from surface water diffusion, ebullition, non-inundated soils, and knees contributed to 14 ± 2%, 25 ± 6%, 34 ± 10%, and 26 ± 5% of total methane emissions, respectively. When considering only the three wetlands with cypress knees present, knee emissions contributed to 39 ± 5% of the total scaled methane emissions. Finally, the molar ratio of CH4 emissions to OC burial ranged from 0.03 to 0.14 in the wetland centers indicating that all four wetland sites are net sources of atmospheric warming potential on 20-100 yr timescales, but net sinks over longer time scales (500 yr) with the exception of one wetland site that was a net source even over 500 yr time scales.

Ward, Nicholas D.↗
DOE OSTI2024

Dissimilar material joining of densified superwood to aluminum by adhesive bonding

Abstract Superwood is a densified wood product that shows promise as a lightweight and renewable alternative for metallic materials. In order for this high-performance new material to be used in multi-material products, it must be able to be joined with other major materials. For example, joining superwood to aluminum would provide a key enabling technology for its use in automotive components since aluminum is presently a major lightweight material for such applications. In this paper, a methacrylate-based adhesive has been identified to provide high lap shear strength (7.5 MPa) for aluminum-to-superwood joints. The aluminum-to-superwood samples were prepared with different amounts of pre-polishing to create openings to the pores in the superwood so adhesive could penetrate into them and create a mechanical interlock, in addition to the hydrogen/chemical bonding at the surface between the methyl methacrylate (MMA) in methacrylate-based adhesive and the cellulose in superwood. For aluminum samples, a thin layer (typically a few nanometers) of oxide film on the surfaces provides hydrogen/chemical bond to MMA structure in the adhesive layer. The failure strength of the superwood-to-aluminum joint sample is about 50% higher than that of natural wood to natural wood joint sample and comparable to that of aluminum-to-aluminum joint sample.

Automation & Control Systems↗
DOE OSTI2020

Electron Trapping and Ion Leaching at the Li-Modified Quartz–Water Interface

Electrons and ions at metal oxide-water interfaces have a critical role in many phenomena and applications, thus making their properties of considerable interest. We here investigate the behavior of a lithium impurity at the water interface with Li-doped SiO 2 using hybrid density functional based ab initio molecular dynamics simulations. We find that the excess electron donated by the lithium dopant localizes on a surface silicon atom and is partially solvated at the aqueous interface. While the position of the excess electron does not change during our ~60 ps simulation, the lithium cation diffuses from its initial position in the SiO 2 subsurface toward the interface and eventually leaches out of the oxide surface and becomes solvated by four water molecules, forming an aqueous Li+- electron complex at the interface. The degree of interaction between the localized electron and the lithium ion controls not only the energy level of the excess electron but also the extent of structural distortion and hydrogen-bonding at the interface. The results of our study can be relevant for understanding the initial stages of glass corrosion, where alkali ions are leached from the surface region by interactions with water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Formation of Gas-Phase Allyl Radicals from Glycerol on Rutile TiO2(110)

The reaction pathways of glycerol on partially reduced TiO2(110) have been studied by a combination of molecular beam dosing and temperature-programmed desorption (TPD). Glycerol is found to bind more strongly to TiO2(110) than glycols due to an additional hydroxyl group in the molecule. When the Ti surface sites are saturated by glycerol, the majority of glycerol molecules (~ 95%) undergo further reactions to yield carbon-free (water and hydrogen) and carbon-containing products that are desorbed during the TPD ramp. In contrast to glycols for which both water and hydrogen arise exclusively from the cleavage of glycol O-H bonds, we identify two distinct reaction channels resulting from the cleavage of O-H and C-H bonds, respectively, for both water and hydrogen evolution from glycerol on TiO2(110). Quantitative determination of the desorption yields of water and hydrogen reveals that the C-H bond scission channel which occurs at higher temperature than the O-H bond scission channel, is a minor reaction channel for water formation, while it is a major reaction channel responsible for hydrogen evolution. For the carbon-containing products, we exclude both carbon deposition and carbon oxides (CO and CO2) formation, and identify the allyl radical as the major carbon-containing product. The formation of the allyl radical is accompanied by the formation of various minor carbon-containing products including propylene, acrolein, allyl alcohol, acetone, formaldehyde and ethylene. The different surface chemistries observed between glycerol and simpler alcohols and glycols on TiO2(110), suggest that smaller oxygenates cannot serve as models for larger oxygenates in probing their reaction pathways on oxide surfaces. The new reaction channels observed for glycerol on TiO2(110) may open up a new way to convert bio-renewable glycerol directly to pure hydrogen and hydrocarbons on TiO2. This work was supported by the US Department of Energy, Office of Sciences, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences, and performed in EMSL, a national scientific user facility sponsored by the Department of Energy’s Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory (PNNL). PNNL is a multiprogram national laboratory operated for the DOE by Battelle.

Chen, Long↗
DOE OSTI2024

Additively Manufacturing Nitinol Shape Memory Alloys for Advanced Actuator Designs

The objective of this research was to understand the role of feedstock production in the phase transformation behavior of additively manufactured Ni-Ti alloys for advanced actuator design. Industrial adoption of additively manufactured Ni-Ti alloys depends on the ability to produce repeatable phase transformation behavior, quantified here by the austenite to martensite transformation on heating. Small variations in the alloy composition may have a significant effect on the temperature at which this transformation occurs. This project showed that the powder characteristics play an important role in determining this behavior. Increases in the surface area per unit volume of the powder, either as a function of size distribution or morphology, have the effect of reducing the Ti content in the alloy through the formation of Ti-rich oxides on the powder surface, which has the effect of depressing the transformation temperature. Preferential Ni vaporization during additive manufacturing can partially offset this effect. To achieve repeatable results, it is important to understand the effect of powder oxidation, and to control the powder characteristics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Impact of Acid–Base Stimulation Sequence on Mineral Stability for Tight/Impermeable Unconventional Carbonate-Rich Rocks: A Delaware Basin Case Study

We report mineral precipitation due to reactions with injected fluids during unconventional fracture stimulation is a well-recognized problem. The goal of this study is to evaluate secondary mineral precipitation and permeability attenuation under chemical injection scenarios specific to the Delaware basin. Whole cylindrical cores (2.54 cm diameter and 2.54 cm height) and ground shale (150–250 μm) from the carbonate-rich Bone Spring Formation, Delaware Basin TX (Leonardian), were reacted at 80 °C and 85 bar using a hydraulic fracturing fluid (HFF) recipe and an injection sequence typical of the Delaware Basin. The reacted shales and solutions were analyzed using a variety of laboratory- and synchrotron-based techniques to characterize both the chemical and spatial distributions of secondary mineral precipitation and identify changes in permeability and mineralogy. This carbonate-rich shale (>84% calcite) rapidly neutralized the acidic HFF. Synchrotron-based X-ray fluorescence mapping coupled with X-ray absorption spectroscopy (both bulk and micro) showed that most of the iron was in an oxidized form prior to exposure to HFF and that almost all iron(II) became fully oxidized after the reaction. Scanning electron microscopy images of the ground shale samples primarily identified iron(oxyhydr)oxide microcrystals on grain surfaces. A few small isolated iron-rich areas also contained sulfur, suggesting that some pyrite was preserved when isolated within a calcite crystal but that most was oxidized. The rapid neutralization of the acid spearhead in these carbonate-rich samples demonstrates that the acid spearhead is useful for initiating fractures in extremely calcite-rich rocks but does little to enhance rock permeability. This suggests that the impact of the acid spearhead is significantly smaller for carbonate-rich shales compared to clay-rich shales, which has broad implications for acidizing in carbonate-rich shale formations and iron transformations within these shales.

58 GEOSCIENCES↗
DOE OSTI2025

Supported Organoiridium-Pincer Catalysts for the Nonoxidative Dehydrogenation of High-Density Polyethylene

The iridium-pincer complex {p-OP( t Bu) 2 -C 6 H 2 -2,6-OP( t Bu) 2 ] 2 }Ir(C 2 H 4 ) ( P [Ir]) has been reported as a stable and active catalyst toward alkane dehydrogenation in homogeneous and supported heterogeneous systems. Dehydrogenation has been shown as a practical method toward functional polyolefins, with dehydrogenated high-density polyethylene (deHDPE) demonstrated as a valuable synthon for upcycling, as orthogonal C-H strategies are key to end-of-life upcycling. The heterogenization of P [Ir] on oxides (SiO 2 , Al 2 O 3 , and TiO 2 ; P [Ir]/E y O x ) yields a mixture of organometallic Ir-fragments whose catalytic nonoxidative dehydrogenation activity is modulated by the binding modes of the active metal on the surface. The binding mode was elucidated by a combination of solid-state NMR and XAFS analyses and supported by DFT calculations. Surface binding through the ligand enables active organoiridium that catalyzes internal olefination of deHDPE up to 1.23 mol % at 200 °C under dynamic vacuum. Alternatively, when the organoiridium is bonded though the metal center (Ir-O SiO ), catalyst activity is negligible. Furthermore, the catalytic activity of P [Ir]/SiO 2 showed comparable reactivity with the homogeneous analogue under the same catalytic conditions, and the heterogenized catalyst can be reused up to three cycles. In conclusion, this work highlights the importance of understanding how organometallic precursors react with hydroxylated metal oxide surfaces to establish structure-property relationships.

Hunt, Samuel B. [Argonne National Laboratory (ANL)↗
DOE OSTI2025

Site-specific surface reactivity on SnO 2 : Evaluating selective atomic layer deposition processes

Area selective atomic layer deposition (AS-ALD) is a bottom-up synthesis approach with potential for deposition with molecular level precision. Here, the site-specific hydration of metal oxide substrates, combined with surface H 2 O-selective ALD processes, provides a potentially powerful path to targeted synthesis. Density functional theory (DFT) calculations are used to predict the thermodynamics of ALD precursor reactivity and hydration for (001), (101), (110), and (100) rutile SnO 2 facets as a function of temperature. Trimethylaluminum (TMA) and dimethyl aluminum isopropoxide (DMAI) dimers are predicted to react with both dehydrated and hydrated SnO 2 (001), (101), and (110) facets at ALD-relevant temperatures, while the SnO 2 (100) facet is predicted to be uniquely unreactive with TMA and DMAI monomers as well as dehydrate near 177 °C making this facet more amenable to targeted ALD. In situ ellipsometric studies of Al 2 O 3 ALD on polycrystalline SnO 2 at 150 °C are consistent with the computational predictions of rapid and unselective nucleation, in stark contrast to inhibited and selective ALD on isostructural rutile TiO 2 .

Atomic Layer Deposition↗
DOE OSTI2024

Steam‐Assisted Selective CO 2 Hydrogenation to Ethanol over Ru−In Catalysts

Abstract Multicomponent catalysts can be designed to synergistically combine reaction intermediates at interfacial active sites, but restructuring makes systematic control and understanding of such dynamics challenging. We here unveil how reducibility and mobility of indium oxide species in Ru‐based catalysts crucially control the direct, selective conversion of CO 2 to ethanol. When uncontrolled, reduced indium oxide species occupy the Ru surface, leading to deactivation. With the addition of steam as a mild oxidant and using porous polymer layers to control In mobility, Ru−In 2 O 3 interface sites are stabilized, and ethanol can be produced with superior overall selectivity (70 %, rest CO). Our work highlights how engineering of bifunctional active ensembles enables cooperativity and synergy at tailored interfaces, which unlocks unprecedented performance in heterogeneous catalysts.

Zhou, Chengshuang↗
DOE OSTI2024

Steam-Assisted Selective CO 2 Hydrogenation to Ethanol over Ru–In Catalysts

Multicomponent catalysts can be designed to synergistically combine reaction intermediates at interfacial active sites, but restructuring makes systematic control and understanding of such dynamics challenging. In this work, we unveil how reducibility and mobility of indium oxide species in Ru-based catalysts crucially control the direct, selective conversion of CO 2 to ethanol. When uncontrolled, reduced indium oxide species occupy the Ru surface, leading to deactivation. With the addition of steam as a mild oxidant and using porous polymer layers to control In mobility, Ru–In 2 O 3 interface sites are stabilized, and ethanol can be produced with superior overall selectivity (70 %, rest CO). Our work highlights how engineering of bifunctional active ensembles enables cooperativity and synergy at tailored interfaces, which unlocks unprecedented performance in heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Time-Dependent Corrosion Behavior of Aluminum Using Advanced Electrochemical and Characterization Techniques

The time-dependent corrosion behavior of pure aluminum (Al) in a chloride-containing environment was investigated using various electrochemical and characterization techniques for up to 336 h. Transmission electron microscopic and secondary ion mass spectroscopic analysis revealed the continuous dissolution of the surface film over the immersion time. In the meantime, the increasing passive oxide thickness resulted in the surface film resistance enhancement over the immersion time, as indicated by the electrochemical impedance spectroscopic analysis. The electrochemical noise measurements showed an increase in the corrosion kinetics with immersion time until 60 h because of the accelerated localized corrosion in the early stage of immersion. However, an inhibition in corrosion kinetics occurred after longer immersion times due to corrosion product deposition inside the pit.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Chromium Tolerant, Highly Active and Stable Electrocatalytic Internal Surface Coating for Cathode of Commercial SOFCs (Final Report)

This project is aimed to develop a chromium (Cr) tolerant, highly active, and stable coating layer on the internal surfaces of the porous composite cathode from commercially available SOFCs. Such coating layer was developed using the additive manufacturing process of Atomic Layer Deposition (ALD) and has been applied on the cathode consisting of either an electronic conductor of LaxSr 1-x MnyO 3-δ (LSM) or mixed ionic and electronic conducting La x Sr 1-x Co y Fe 1-y O 3-δ (LSCF). PI's work has demonstrated that the internal surface of cathode from the commercial cells, can be further tailored using ALD coating to dramatically enhance the cell performance. For instance, ALD layer consisting heterostructured nano composite of nano-Pt and nano-(Mn 0.8 Co 0.2 ) 3 O 4 oxide on the internal surface of porous LSM/YSZ cathode from SOFCs, has resulted in the large reduction of the cell polarizations resistance by up to 53%, and enormous increase of power density over 370%. For the cells with LSCF/Sm 2 O 3 doped CeO 2 (SDC) cathode, the conformal layer of nano-composite consisting of superjacent CoOx and subjacent minimum amount of Pt nano-grains has resulted in the power density enhancement by 126% for the large scale industry tubular cells at 750°C, and both the performance enhancement and nanostructure of the ALD layer are stable over ~ 2000 h continuous operation performed at industry test station. In the meanwhile, those ALD coating layer developed by PI's work is also inherently Cr-tolerant, and could act as physical barrier for preventing Cr diffusion into the cathode backbone, so as to mitigate the Cr poisoning effect on the cathode. In this project, the impact of Cr on the performance of those ALD coated commercial cells has been evaluated. Based on evolution of the cell performance, the ALD coating layer chemistry and ALD coating layer thickness has been optimized to maximize the overall Cr tolerance, cell power density and cell longevity. Different ALD coating has been applied onto the internal surface of LSM/YSZ and LSCF/SDC backbone respectively. The architecture/scaffold structures on the internal surface of different cathode, designed by this project, was catalogued and analyzed using High Resolution Transmission Electron Microscopy (HRTEM), and cell power/durability performance are assured via comprehensive electrochemical performance testing in the industry operation relevant conditions. The impact of the electrochemical operation current density, the water humidity, the cell operation temperature, and cell operation duration on the Cr tolerance of ALD coated cells has been systematically investigated. There is completely different nanostructure degradation mechanisms between LSM and LSCF cells induced by Cr contamination. For the LSCF/SDC baseline cell, With the Cr source, there is no apparent Sr surface segregation phase even for the baseline cell operated for 3000 h at 750 °C. With the Cr source, there is significant amorphous (SrCr)Ox phase accumulated in the original pore region. For the commercial baseline cells, Cr contaminants on the LSM electrode severely impacted the entire cell's electrochemical performance and nanostructure degradation. Those degradations include (1). Peak power density loss of 64 % after 109 h of operation. The dramatic increase in Rp (2). They are cracking at LSM/SSZ interface, LSM grains. SSZ remains intact but with (CrMn)Ox. By contrast, ALD coating (MnCo)Ox/Pt dramatically improves the Cr resistance, as follows (1). ALD-coated cell with a power density is 280-380 % of the baseline cell, depending on the ALD layer thickness. (2). For a cell with a 20 nm thick ALD layer, there is a large performance enhancement (> 200 % power density) induced by ALD coating of Cr-tolerant Mn 0.8 Co 0.2 Ox. (3). For a cell with a 20 nm thick ALD layer, after 168 h at 750 °C power density of the ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination for 109 h. The ALD coating on the internal surface of cathode developed by this project integrated multi-functions. Those multi-functions include (1). Dramatically improving the cell power density for the commercial cells; (2). Dramatically improving contamination resistance of the cathode, for being an excellent protection coating layer sealing off Cr contamination. (3). Dramatically increasing the cell longevity by potentially preventing the microstructure evolution and grain coarsening of the cathode. Overall, this project will provide a simple solution to simultaneously enhance power density and increase the reliability, robustness, and endurance of commercial SOFCs, over the entire operating temperature range of 650-800 °C. For the inherently functional SOFC, the ALD coating of LSM based cathode mitigate the Cr-contamination. Power density of ALD-coated cell is ~ 600% of that baseline cell upon operation with Cr contamination. In addition to SOFCs, the novel on-demand design approach and creation of multifunctional heterogeneous architecture on the electrode surface presented in this work opens further research for their application in other types of fuel cells, batteries, and sensors for which electrochemical reactions on the surface are similarly critical.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Reliability of Copper Inverse Opal Surfaces for Extreme-Heat-Flux Micro-Coolers in Low-Global-Warming-Potential Refrigerant R-1233zd Pool Boiling Experiments

This presentation provides a brief snapshot of the InterPACK paper InterPACK2023-113781. The paper explores copper inverse opal (CIO) surface reliability in pool boiling experiments in water and a new, low-global-warming-potential (GWP = 1) hydrofluoroolefin (HFO) refrigerant R-1233zd. The CIO-based structure is intended to develop enhanced two-phase heat transfer surfaces for extreme-heat-flux (approximately 1 kW/cm2) micro-coolers. In this study, a limited number of pool boiling experiments were performed using water and HFO-1233zd fluid, and the reliability of the CIO-based surfaces was evaluated. Critical heat flux (CHF) values in HFO-1233zd at 40 Degrees Celsius to 45 Degrees Celsius saturation temperatures and the corresponding saturation pressures were also measured. The CHF values with the refrigerant are significantly lower compared to those with water, but the refrigerant allows for a wider usable temperature range in the end application of the micro-coolers and is not limited to data centers with controlled ambient conditions. Reliability experiments with CIO surface samples - involving pool boiling with water on the CIO surfaces for approximately 48 hours and with HFO-1233zd for 144 hours - showed no structural degradation of the enhanced surface or any significant performance drop in heat transfer coefficients. The CIO surface samples in water were oxidized, most likely due to the presence of air in water and in the experimental vessel.

critical heat flux↗
DOE OSTI2021

RF surface resistance tuning of superconducting niobium via thermal diffusion of native oxide

Recently, Nb superconducting radio frequency cavities vacuum heat treated between 300 and 400°C for a few hours have exhibited very high quality factors (~5 × 10 10 at 2.0 K). Secondary ion mass spectrometry measurements of O, N, and C show that this enhancement in RF surface conductivity is primarily associated with interstitial O alloying via dissolution and diffusion of the native oxide. We use a theory of oxide decomposition and O diffusion to quantify previously unknown parameters crucial in modeling this process. RF measurements of a vacuum heat-treated Nb superconducting radio frequency cavity confirm the minimized surface resistance (higher Q 0 ) previously expected only from 800 °C diffusive alloying with N.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗