Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cell Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 865 records · Page 48
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Screening Li-Ion Batteries for Internal Shorts

The extremely high cost of aerospace battery failures due to internal shorts makes it essential that their occurrence be very rare, if not eliminated altogether. With Li-ion cells/batteries, the potentially catastrophic safety hazard that some internal shorts present adds additional incentive for prevention. Prevention can be achieved by design, manufacturing measures, and testing. Specifically for NASA s spacesuit application, a Li-ion polymer pouch cell battery design is in its final stages of production. One of the 20 flight batteries fabricated and tested developed a cell internal short, which did not present a safety hazard, but has required revisiting the entire manufacturing and testing process. Herein are the details of the failure investigation that followed to get to root cause of the internal short and the corrective actions that will be taken. The resulting lessons learned are applicable to most Li-ion battery applications.

Darcy, Eric↗
DOE OSTI2025

Interface diagnostics platform for thin-film solid-state batteries

Understanding the impedances of battery materials and their interfaces remains a major challenge, usually addressed by electrochemical impedance spectroscopy (EIS) where frequency-dependent complex impedance of full battery cells is measured and then modeled by a network of connected electrical elements. As conventionally applied, this approach produces ambiguity in that (1) multiple different network configurations may fit the data convincingly and (2) the method offers no direct association of the electrical elements with physical features of the battery. Here we present a new methodology that resolves both sources of ambiguity, enabled by expanding the experimental scope to directly inform the configuration of elements and their parameters in the network model. We demonstrate this methodology using thin film fabrication of solid state battery devices patterned by shadow masked sputter deposition, so that diagnostic devices corresponding to individual interface and material components can be fabricated simultaneously with full cell batteries. EIS models for the diagnostic devices can then be connected to form full cell networks whose topology matches the well-known physical configuration of the battery. When connected in this way, the full network model – made from connecting the diagnostic device EIS models – fits the full cell EIS data. For the case of a thin film solid state battery composed of amorphous silicon anode, lithium phosphorus oxynitride (LiPON) solid electrolyte, and lithium vanadium oxide (Li x V 2 O 5 ) cathode, we show that the approach allows us to identify ionic impedance/conductivity of the cathode/electrolyte as a limiting impedance and the anode/electrolyte interface cycling instability as a primary degradation factor.

25 ENERGY STORAGE↗
DOE OSTI2022

Toward high efficiency at high temperatures: Recent progress and prospects on InGaN-Based solar cells

III-nitride InGaN material is an ideal candidate for the fabrication of high performance photovoltaic (PV) solar cells, especially for high-temperature applications. Over the past decade, significant efforts have been made to improve the PV performance of InGaN-based solar cells. In this paper, we perform a comprehensive review of the recent developments in InGaN-based solar cells. The topics of discussion include theoretical modeling, material epitaxy, device engineering, and high-temperature measurement. Particularly, we highlight subjects such as substrate technology, and properties that are unique to InGaN materials such as polarization control and their positive thermal coefficient. To date, outstanding high-temperature InGaN-based solar cells with quantum efficiency approaching 80% at 450 °C have been demonstrated. In conclusion, future innovations in epitaxy science, device engineering, and integration methods are required to further advance the efficiency and expand the applications of InGaN-based solar cells.

14 SOLAR ENERGY↗
NASA NTRS1979

Thin cells for space

Research and pilot line production efforts directed towards the fabrication of high efficiency ultrathin silicon solar cells (50 micrometers) are reported. Conventional ultrathin cells with air-mass-zero (AM0) efficiencies exceeding 14% and coplanar back contact cells with AM0 efficiencies up to 11.7% were developed. The primary mechanisms limiting efficiency were determined in both types of cells, and they are discussed within the context of further improving efficiency. Results of pilot line production of conventional ultrathin cells are also presented. Average AM0 efficiencies of 12% were readily achieved for 2000 cell production runs.

Storti, G.↗
NASA NTRS1977

Procedure for minimizing the cost per watt of photovoltaic systems

A general analytic procedure is developed that provides a quantitative method for optimizing any element or process in the fabrication of a photovoltaic energy conversion system by minimizing its impact on the cost per watt of the complete system. By determining the effective value of any power loss associated with each element of the system, this procedure furnishes the design specifications that optimize the cost-performance tradeoffs for each element. A general equation is derived that optimizes the properties of any part of the system in terms of appropriate cost and performance functions, although the power-handling components are found to have a different character from the cell and array steps. Another principal result is that a fractional performance loss occurring at any cell- or array-fabrication step produces that same fractional increase in the cost per watt of the complete array. It also follows that no element or process step can be optimized correctly by considering only its own cost and performance

Redfield, D.↗
DOE OSTI2021

Solar cell comprising an oxide-nanoparticle buffer layer and method of fabrication

A buffer layer for protecting an organic layer during high-energy deposition of an electrically conductive layer is disclosed. Buffer layers in accordance with the present invention are particularly well suited for use in perovskite-based single-junction solar cells and double-junction solar cell structures that include at least one perovskite-based absorbing layer. In some embodiments, the buffer layer comprises a layer of oxide-based nanoparticles that is formed using solution-state processing, in which a solution comprising the nanoparticles and a volatile solvent is spin coated onto a structure that includes the organic layer. The solvent is subsequently removed in a low-temperature process that does not degrade the organic layer.

Bush, Kevin Alexander↗
DOE OSTI2020

Metamaterials for Mechanically Directing Cell Phenotype

Recently, abundant research has begun to reveal how microscale surface topography can influence a wide range of cell phenotypes in vitro, such as cell mobility, cell size and cell viability (Flemming et al. 1999, Nikkhah et al. 2012, Wang et al. 2016). However, while these studies shed some light on cell interactions with 2D surfaces of different length scales, cells in vivo experience their surroundings in 3D. Therefore, investigations into cell interactions with varying 3D microstructures are needed to gain biologically relevant insight into how microarchitecture and feature size influences cell behavior. Understanding this relationship between 3D microstructure and cell behavior will have a huge impact on tissue engineering and mechanobiology. Until now, the ability to fabricate complex 3D microstructures for cell behavior studies has been limited. This study harnessed LLNL’s Projection Micro-Stereolithography (PμSL) capability to probe the effects of micron-scale changes in 3D architecture on cell phenotype. Furthermore, our studies explored the application of external forces—such as cyclic loading and flow-induced shear stress—to cell-seeded 3D microstructures to further examine cell behavior.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Hermetic edge sealing of photovoltaic modules

The feasibility of using an electrostatic bonding (ESB) and ultrasonic welding process to produce hermetic edge seals on terrestrial solar cell modules was investigated. The fabrication sequence is to attach an aluminum foil "gasket' to the perimeter of a glass sheet. A cell circuit is next encapsulated inside the gasket, and its aluminum foil back cover is seam welded ultrasonically to the gasket. An ESB process for sealing aluminum to glass was developed in an ambient air atmosphere, which eliminates the requirement for a vacuum or pressure vessel. An ultrasonic seam welding process was also developed which did not degrade the quality of the ESB seal. Good quality welds with minimal deformation were produced. The effectiveness of the above described sealing techniques was tested by constructing 400 sq cm (8 x 8 s64 sq in) sample modules, and then subjecting them to nondestructive fine and gross leak tests. The gross leak tests identified several different causes of leaks which were then eliminated by modifying the assembly process.

Nowlan, M. J.↗
NASA NTRS1985

Defects and device performance

The necessity for a low-cost crystalline silicon sheet material for photovoltaics has generated a number of alternative crystal growth techniques that would replace Czochralski (Cz) and float-zone (FZ) technologies. Efficiencies of devices fabricated from low resistivity FZ silicon are approaching 20%, and it is highly likely that this value will be superseded in the near future. However, FZ silicon is expensive, and is unlikely ever to be used for photovoltaics. Cz silicon has many of the desirable qualities of FZ except that minority-carrier lifetimes at lower resistivities are significantly less than those of FZ silicon. Even with Cz silicon, it is unlikely that cost goals can be met because of the poor-material yield that results from sawing and other aspects of the crystal rowth. Although other silicon sheet technologies have been investigated, almost all have characteristics that limit efficiency to approx. 16%. In summary, 20% efficient solar cells can likely be fabricated from both FZ and Cz silicon, but costs are likely to be ultimately unacceptable. Alternate silicon technologies are not likely to achieve this goal, but cost per watt figures may be eventually better than either of the single crystal technologies and may rival any thin-film technology.

Storti, G.↗
DOE OSTI2024

Toward Mass-Production of Transition Metal Dichalcogenide Solar Cells: Scalable Growth of Photovoltaic-Grade Multilayer WSe2 by Tungsten Selenization

Semiconducting transition metal dichalcogenides (TMDs) are promising for high-specific-power photovoltaics due to their desirable band gaps, high absorption coefficients, and ideally dangling-bond-free surfaces. Despite their potential, the majority of TMD solar cells to date are fabricated in a nonscalable fashion, with exfoliated materials, due to the lack of high-quality, large-area, multilayer TMDs. Here, we present the scalable, thickness-tunable synthesis of multilayer WSe2 films by selenizing prepatterned tungsten with either solid-source selenium at 900 degrees C or H2Se precursors at 650 degrees C. Both methods yield photovoltaic-grade, wafer-scale WSe2 films with a layered van der Waals structure and superior characteristics, including charge carrier lifetimes up to 144 ns, over 14x higher than those of any other large-area TMD films previously demonstrated. Simulations show that such carrier lifetimes correspond to ~22% power conversion efficiency and ~64 W g-1 specific power in a packaged solar cell, or ~3 W g-1 in a fully packaged solar module. The results of this study could facilitate the mass production of high-efficiency multilayer WSe2 solar cells at low cost.

carrier lifetime↗
NASA NTRS1985

High-voltage solar-cell chip

Integrated circuit technology has been successfully applied to the design and fabrication of 0.5 x 0.5-cm planar multijunction solar-cell chips. Each of these solar cells consisted of six voltage-generating unit cells monolithically connected in series and fabricated on a 75-micron-thick, p-type, single crystal, silicon substrate. A contact photolithic process employing five photomask levels together with a standard microelectronics batch-processing technique were used to construct the solar-cell chip. The open-circuit voltage increased rapidly with increasing illumination up to 5 AM1 suns where it began to saturate at the sum of the individual unit-cell voltages at a maximum of 3.0 V. A short-circuit current density per unit cell of 240 mA/sq cm was observed at 10 AM1 suns.

Kapoor, V. J.↗
DOE OSTI2021

Pressure and thermal annealing effects on the photoconversion efficiency of polymer solar cells

This paper presents the results of experimental and theoretical studies of the effects of pressure and thermal annealing on the photo-conversion efficiencies (PCEs) of polymer solar cells with active layers that consist of a mixture of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative (6,6)-phenyl-C 61 -butyric acid methyl ester. The PCEs of the solar cells increased from ~2.3% (for the unannealed devices) to ~3.7% for devices annealed at ~150 °C. A further increase in thermal annealing temperatures (beyond 150 °C) resulted in lower PCEs. Further improvements in the PCEs (from ~3.7% to ~5.4%) were observed with pressure application between 0 and 8 MPa. However, a decrease in PCEs was observed for pressure application beyond 8 MPa. The improved performance associated with thermal annealing is attributed to changes in the active layer microstructure and texture, which also enhance the optical absorption, mobility, and lifetime of the optically excited charge carriers. The beneficial effects of applied pressure are attributed to the decreased interfacial surface contacts that are associated with pressure application. The implications of the results are then discussed for the design and fabrication of organic solar cells with improved PCEs.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Solid polymer membrane program

The results are presented for a solid polymer electrolyte fuel cell development program. Failure mechanism was identified and resolution of the mechanism experienced in small stack testing was demonstrated. The effect included laboratory analysis and evaluation of a matrix of configurations and operational variables for effects on the degree of hydrogen fluoride released from the cell and on the degree of blistering/delamination occurring in the reactant inlet areas of the cell and to correlate these conditions with cell life capabilities. The laboratory evaluation tests were run at conditions intended to accelerate the degradation of the solid polymer electrolyte in order to obtain relative evaluations as quick as possible. Evaluation of the resolutions for the identified failure mechanism in space shuttle configuration cell assemblies was achieved with the fabrication and life testing of two small stack buildups of four cell assemblies and eight cells each.

Source record↗
DOE OSTI2021

Lamination of transparent conductive adhesives for tandem solar cell applications

A transparent conductive adhesive (TCA) interlayer for mechanically stacked multijunction solar cells provides adhesive strength and electrical connection between sub-cells when stacked. The fabrication of TCA sheets from an ethyl-vinyl acetate (EVA) matrix and silver coated compliant conductive microspheres, similar to industry-standard EVA encapsulant sheets, compatible with a standard lamination process was developed. Blade coating TCA sheets using 3D printed blades and testing of vertical conduction through the interlayer with a TCA conductivity jig allowed for reproducible measurements and low-cost fabrication. The supplemental information provides design files to enable other researchers to produce their own blades and testing jigs. We identified 0.5 mm as an optimal blade height for producing lab-scale TCA sheets and 120 °C at 3 psi for 10 min as the optimal vacuum lamination process to minimize resistance and possible damage to samples. For TCA sheets with coverages between 0.75% and 9%, the series resistance was approximately 0.2 O cm2 which should result in minimal losses for one-sun photovoltaic applications.

14 SOLAR ENERGY↗
DOE OSTI2024

Lamination of >21% Efficient Perovskite Solar Cells with Independent Process Control of Transport Layers and Interfaces

Transport layer and interface optimization is critical for improving the performance and stability of perovskite solar cells (PSCs) but is restricted by the conventional fabrication approach of sequential layer deposition. While the bottom transport layer is processed with minimum constraints, the narrow thermal and chemical stability window of the halide perovskite (HP) layer severely restricts the choice of top transport layer and its processing conditions. To overcome these limitations, we demonstrate lamination of HPs—where two transport layer-perovskite half-stacks are independently processed and diffusion-bonded at the HP-HP interface—as an alternative fabrication strategy that enables self-encapsulated solar cells. Power conversion efficiencies (PCE) of >21% are realized using cells that incorporate a novel transport layer combination along with dual-interface passivation via self-assembled monolayers, both of which are uniquely enabled by the lamination approach. This is the highest reported PCE for any laminated PSC encapsulated between glass substrates. We further show that this approach expands the processing window beyond traditional fabrication processes and is adaptable for different transport layer compositions. The laminated PSCs retained >75% of their initial PCE after 1000 h of 1-sun illumination at 40 °C in air using an all-inorganic transport layer configuration without additional encapsulation. Furthermore, a laminated 1 cm 2 device maintained a V oc of 1.16 V. Finally, the scalable lamination strategy in this study enables the implementation of new transport layers and interfacial engineering approaches for improving performance and stability.

14 SOLAR ENERGY↗
DOE OSTI2022

Hot-Casting-Assisted Liquid Additive Engineering for Efficient and Stable Perovskite Solar Cells

High-performance inorganic–organic lead halide perovskite solar cells (PSCs) are often fabricated with a liquid additive such as dimethyl sulfoxide (DMSO), which retards crystallization and reduces roughness and pinholes in the perovskite layers. However, DMSO can be trapped during perovskite film formation and induce voids and undesired reaction byproducts upon later processing steps. Here, it is shown that the amount of residual DMSO can be reduced in as-spin-coated films significantly through use of preheated substrates, or a so-called hot-casting method. Hot casting increases the perovskite film thickness given the same concentration of solutions, which allows for reducing the perovskite solution concentration. By reducing the amount of DMSO in proportion to the concentration of perovskite precursors and using hot casting, it is possible to fabricate perovskite layers with improved perovskite–substrate interfaces by suppressing the formation of byproducts, which increase trap density and accelerate degradation of the perovskite layers. The best-performing PSCs exhibit a power conversion efficiency (PCE) of 23.4% (23.0% stabilized efficiency) under simulated solar illumination. Furthermore, encapsulated devices show considerably reduced post-burn-in decay, retaining 75% and 90% of their initial and post-burn-in efficiencies after 3000 h of operation with maximum power point tracking (MPPT) under high power of ultraviolet (UV)-containing continuous light exposure.

perovskite-substrate interface↗
NASA NTRS1986

Use of low-energy hydrogen ion implants in high-efficiency crystalline-silicon solar cells

The use of low-energy hydrogen implants in the fabrication of high-efficiency crystalline silicon solar cells was investigated. Low-energy hydrogen implants result in hydrogen-caused effects in all three regions of a solar cell: emitter, space charge region, and base. In web, Czochralski (Cz), and floating zone (Fz) material, low-energy hydrogen implants reduced surface recombination velocity. In all three, the implants passivated the space charge region recombination centers. It was established that hydrogen implants can alter the diffusion properties of ion-implanted boron in silicon, but not ion-implated arsenic.

Fonash, S. J.↗