Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “aerodynamic optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 847 records · Page 47
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Schlieren Imaging Of An Aircraft In Flight

Technique for making schlieren images of airplanes and missiles in supersonic flight devised to help understand physics of compressible aerodynamic flows about complicated aircraft shapes. Technique also used to study far-field sonic booms. Data obtained from schlieren images useful in optimizing designs of prototype aircraft. Technique incorporates elements of focusing schlieren photography, astronomical photography, and streak photography. Using sun or moon as source of light, apparatus forms image revealing gradients of density in air flow.

Weinstein, Leonard M.↗
NASA NTRS1976

Exploratory investigation of aeroacoustic optimization of the variable impedance edge concept applied to upper surface blown configurations

The feasibility of using porous surfaces on lift augmentation flaps to reduce the noise at the source, without adversely affecting aerodynamic performance was investigated. Numerous flap configurations were tested on a USB (upper surface blowing) type powered lift model (approximately 1/5 full scale). Significant reductions of far field noise and aeroacoustic pressures were found, and many configurations exhibited aerodynamic characteristics comparable to unmodified configurations of the nozzle/flap system.

Hayden, R. E.↗
NASA NTRS1979

Supercritical wing design using numerical optimization and comparisons with experiment

A numerical minimization scheme is used in conjunction with two-dimensional and three-dimensional inviscid transonic flow analysis codes to provide procedures for wing leading edge aerodynamic design. The procedures are demonstrated in the design of a new leading edge to improve C-141 cruise performance. For the high aspect ratio moderately swept C-141 wing, the 2-D procedure is shown to yield results which are in close agreement with those obtained using the 3-D technique. Although the 2-D approach uses much less computation time than the 3-D technique, the latter requires fewer manhours than the former. Comparisons of predicted and wind tunnel measured performance improvements are presented which verify the design procedures.

Lores, M. E.↗
NASA NTRS1987

Constrained optimization techniques for active control of aeroelastic response

Active control of aeroelastic response is a complex problem in which the designer usually tries to satisfy many design criteria which are often conflicting in nature. To further complicate the design problem, the state space equations describing this type of control problem are usually of high order, involving a large number of states to represent the flexible structure and unsteady aerodynamics. Control laws based on the standard Linear - Quadratic - Gaussian method are of the same high order as the aeroelastic plant and may be difficult to implement in the flight computer. To overcome this disadvantage a new approach was developed for designing low-order optimized robust control laws. In this approach, a nonlinear programming algorithm is used to search for the values of control law design variables that minimize a performance index while satisfying several inequality constraints that describe the design criteria on the stability robustness and responses. The method is applied to a gust load alleviation problem and a stability robustness improvement problem of a drone aircraft.

Mukhopadhyay, Vivekananda↗
NASA NTRS1986

Evaluation of propeller/nacelle interactions in the PTA program

Advanced highly-loaded propellers are proposed to power transport aircraft that cruise at high subsonic speeds giving significant fuel savings over the equivalent turbofan engine. In order to realize these savings, the propeller must be installed so that the aerodynamics of the propeller/nacelle combination do not lead to excessive cyclic blade stresses or installation losses. The on-going, NASA sponsored, Propfan Test Assessment Program (PTA) has provided the first high-speed wind-tunnel data on an installed propfan complete with an inlet. This paper presents computational techniques that allow: (1) optimization of inlet plane location, (2) contouring of lip and cowl, and (3) estimation of propeller cyclic loads due to a nonuniform flowfield. These computational methods, in spite of the complexity of the configuration and the slipstream effects, provide predictions of aerodynamic performance which are in excellent agreement with wind-tunnel data.

Aljabri, A. S.↗
NASA NTRS1992

Mixing in the dome region of a staged gas turbine combustor

To lower NO(x) emissions from gas-turbine engines the effect of dome design and operational changes on the mixing quality in the fuel-rich region is studied. A statistical analysis is employed to establish the parametric sensitivity in this complex flow. A mixing-effectiveness index is defined and used to optimize the gas-species uniformity and the extent of reaction at the exit plane of the dome. Mixing effectiveness is tied to the fuel and air injection locations, the macroscale structure of the dome aerodynamics, and the level of turbulence. Increases in nozzle/air to fuel ratio, reference velocities, and the dome expansion angle increased the level of turbulence. The optimum configuration featured counter-swirling fuel and air streams and produced a strong torroidal recirculation zone, an effective spray angle of 45 degrees, and azimuthal velocities that decayed to zero inside of two duct diameters. The results underscore the system specific nature of mixing optimization.

Sowa, W. A.↗
NASA NTRSDate not supplied

Analysis and Optimization of Baseline Single Aisle Aircraft for Future Electrified Powertrain Flight Demonstrator Comparisons

The purpose of this study is to provide baseline single-aisle vehicles for future comparisons NASA’s Electrified Powertrain Flight Demonstrator (EPFD) turbofan powered Vision Systems. Both a large single-aisle (≈150 passenger) and a small single-aisle (≈100 passenger) vehicle will be analyzed using NASA’s General Aviation Synthesis Program and a modernized Python-based version of this program that enables efficient gradient-based optimization of both the airframe and propulsion that currently is being referred to as GASPy. A technology build-up will be conducted to bring the current State-of-the-art vehicles to a projected 2035 technology level by incorporating estimations for improvements in aerodynamics, structures, and propulsions. These vehicles can be used in NASA’s future EPFD project as baselines to measure the benefits of future hybrid and fully electric aircraft against. The advanced, large single-aisle will then be used to demonstrate the benefits of a coupled engine-airframe optimization for fuel burn reduction.

Carl J Recine↗
NASA NTRS1986

Model-following control for an oblique-wing aircraft

A variable-skew oblique wing offers a substantial aerodynamic performance advantage for aircraft missions that require both high efficiency in subsonic flight and supersonic dash or cruise. The most obvious characteristic of the oblique-wing concept is the asymmetry associated with wing-skew angle which results in significant aerodynamic and inertial cross-coupling between the aircraft longitudinal and lateral-directional axes. This paper presents a technique for synthesizing a decoupling controller while providing the desired stability augmentation. The proposed synthesis procedure uses the concept of explicit model following. Linear quadratic optimization techniques are used to design the linear feedback system. The effectiveness of the control laws developed in achieving the desired decoupling is illustrated for a given flight condition by application to linearized equations of motion, and also to the nonlinear equations of six degrees of freedom of motion with nonlinear aerodynamic data.

Alag, G. S.↗
NASA NTRS1994

Aeroacoustic sensitivity analysis and optimal aeroacoustic design of turbomachinery blades

During the first year of the project, we have developed a theoretical analysis - and wrote a computer code based on this analysis - to compute the sensitivity of unsteady aerodynamic loads acting on airfoils in cascades due to small changes in airfoil geometry. The steady and unsteady flow though a cascade of airfoils is computed using the full potential equation. Once the nominal solutions have been computed, one computes the sensitivity. The analysis takes advantage of the fact that LU decomposition is used to compute the nominal steady and unsteady flow fields. If the LU factors are saved, then the computer time required to compute the sensitivity of both the steady and unsteady flows to changes in airfoil geometry is quite small. The results to date are quite encouraging, and may be summarized as follows: (1) The sensitivity procedure has been validated by comparing the results obtained by 'finite difference' techniques, that is, computing the flow using the nominal flow solver for two slightly different airfoils and differencing the results. The 'analytic' solution computed using the method developed under this grant and the finite difference results are found to be in almost perfect agreement. (2) The present sensitivity analysis is computationally much more efficient than finite difference techniques. We found that using a 129 by 33 node computational grid, the present sensitivity analysis can compute the steady flow sensitivity about ten times more efficiently that the finite difference approach. For the unsteady flow problem, the present sensitivity analysis is about two and one-half times as fast as the finite difference approach. We expect that the relative efficiencies will be even larger for the finer grids which will be used to compute high frequency aeroacoustic solutions. Computational results show that the sensitivity analysis is valid for small to moderate sized design perturbations. (3) We found that the sensitivity analysis provided important insight into how airfoils should be modified to improve their aeroelastic stability. Using this insight, we redesigned an aeroelastically unstable cascade to produce a stable cascade.

Hall, Kenneth C.↗
NASA NTRS1992

Aeroelastic optimization of an advanced geometry helicopter rotor

Sensitivity derivatives of blade loads and aeroelastic stability of a helicopter rotor in forward flight are calculated as an integral part of a basic aeroelastic analysis using a direct analytical approach. Design variables include nonstructural mass and its placement, chordwise offset of blade center of gravity and aerodynamic center from the elastic axis, blade bending stiffnesses (flap, lag, torsion), and tip geometry (sweep, anhedral, pretwist and planform taper). By means of a sensitivity study, the importance of different design variables on oscillatory hub loads and damping of blade modes is examined. Aeroelastic and sensitivity analyses of the rotor based on a finite element method in space and time are linked with automated optimization algorithms to perform optimization studies of rotor blades. Optimum design solutions, calculated for a four-bladed, soft-inplane hingeless rotor achieved a reduction of 25-60 percent of all 4/rev loads.

Ganguli, Ranjan↗
NASA NTRS1991

Recent progress in inverse methods in France

Given the current level of jet engine performance, improvement of the various turbomachinery components requires the use of advanced methods in aerodynamics, heat transfer, and aeromechanics. In particular, successful blade design can only be achieved via numerical design methods which make it possible to reach optimized solutions in a much shorter time than ever before. Two design methods which are currently being used throughout the French turbomachinery industry to obtain optimized blade geometries are presented. Examples are presented for compressor and turbine applications. The status of these methods as far as improvement and extension to new fields of applications is also reported.

Bry, Pierre-Francois↗
NASA NTRS1992

Heat transfer characteristics of hypersonic waveriders with an emphasis on leading edge effects

The present analysis of the heat-transfer characteristics of a family of viscous-optimized, 60 m-long waverider hypersonic vehicles gives attention to the transition from laminar to turbulent flow, and to how the transition affects aerodynamic heating distributions over the waverider surface. Two different constant-dynamic-pressure flight trajectories are considered, at 0.2 and 1.0 freestream atmospheres. For Mach numbers below 10, it is found that passive radiative cooling of the surface is sufficient. The degree of leading-edge bluntness required by aerodynamic heating constraints does not significantly degrade the aerodynamic performance of these waveriders.

Vanmol, Denis O.↗
DOE OSTI2022

Characterization of an aerosolized nanoparticle beam beyond the diffraction limit through strong field ionization

Abstract The study of nanomaterials is an active area of research for technological applications as well as fundamental science. A common method for studying properties of isolated nanoparticles is by an in-vacuum particle beam produced via an aerodynamic lens. Despite being common practice, characterization of such beams has proven difficult as light scattering detection techniques fail for particles with sizes beyond the diffraction limit. Here we present a new technique for characterizing such nanoparticle beams using strong field ionization. By focusing an ultrafast, mJ-level laser into the particle beam, a nanoparticle within the laser focus is ionized and easily detected by its ejected electrons. This method grants direct access to the nanoparticle density at the location of the focus, and by scanning the focus through the transverse and longitudinal profiles of the particle beam we attain the 3-dimensional particle density distribution for a cylindrically symmetric beam. Further, we show that strong field ionization is effective in detecting spherical nanoparticles as small as 10 nm in diameter. Additionally, this technique is an effective tool in optimizing the particle beam for specific applications. As an example we show that the particle beam density and width can be manipulated by restricting the gas flow into the aerodynamic lens.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS1990

Preliminary design optimization of joined-wing aircraft

The joined wing is an innovative aircraft configuration that has a its tail connected to the wing forming a diamond shape in both top and plan view. This geometric arrangement utilizes the tail for both pitch control and as a structural support for the wing. Several researchers have studied this configuration and predicted significant reductions in trimmed drag or structural weight when compared with a conventional T-tail configuration. Kroo et al. compared the cruise drag of joined wings with conventional designs of the same lifting-surface area and structural weight. This study showed an 11 percent reduction in cruise drag for the lifting system of a joined wing. Although this reduction in cruise drag is significant, a complete design study is needed before any economic savings can be claimed for a joined-wing transport. Mission constraints, such as runway length, could increase the wing area and eliminate potential drag savings. Since other design codes do not accurately represent the interaction between structures and aerodynamics for joined wings, we developed a new design code for this study. The aerodynamic and structural analyses in this study are significantly more sophisticated than those used in most conventional design codes. This sophistication was needed to predict the aerodynamic interference between the wing and tail and the stresses in the truss-like structure. This paper describes these analysis methods, discusses some problems encountered when applying the numerical optimizer NPSOL, and compares optimum joined wings with conventional aircraft on the basis of cruise drag, lifting surface weight, and direct operating cost (DOC).

Gallman, John W.↗
NASA NTRS2010

Estimation of Supersonic Stage Separation Aerodynamics of Winged-Body Launch Vehicles Using Response Surface Methods

Response surface methodology was used to estimate the longitudinal stage separation aerodynamic characteristics of a generic, bimese, winged multi-stage launch vehicle configuration at supersonic speeds in the NASA LaRC Unitary Plan Wind Tunnel. The Mach 3 staging was dominated by shock wave interactions between the orbiter and booster vehicles throughout the relative spatial locations of interest. The inference space was partitioned into several contiguous regions within which the separation aerodynamics were presumed to be well-behaved and estimable using central composite designs capable of fitting full second-order response functions. The underlying aerodynamic response surfaces of the booster vehicle in belly-to-belly proximity to the orbiter vehicle were estimated using piecewise-continuous lower-order polynomial functions. The quality of fit and prediction capabilities of the empirical models were assessed in detail, and the issue of subspace boundary discontinuities was addressed. Augmenting the central composite designs to full third-order using computer-generated D-optimality criteria was evaluated. The usefulness of central composite designs, the subspace sizing, and the practicality of fitting lower-order response functions over a partitioned inference space dominated by highly nonlinear and possibly discontinuous shock-induced aerodynamics are discussed.

Erickson, Gary E.↗
NASA NTRS1987

Design sensitivity analysis for an aeroelastic optimization of a helicopter blade

The sensitivity of vibratory hub loads of a four-bladed hingeless rotor with respect to blade design parameters is investigated using a finite element formulation in space and time. Design parameters include nonstructural mass distribution (spanwise and chordwise), chordwise offset of center of gravity from aerodynamic center, blade bending stiffnesses (flap, lag and torsion). Hub loads selected are 4/rev vertical hub shear and 3/rev hub moment in the rotating reference frame. The sensitivity derivatives of vertical hub loads with respect to blade design parameters are compared using two approaches, finite difference scheme and analytical approach using chain rule differentiation. The analytical derivative approach developed as an integral part of response solution (finite element in time) is a powerful method for an aeroelastic optimization of a helicopter rotor.

Lim, Joon↗
NASA NTRS1984

Applications of CONMIN to wing design optimization with vortex flow effect

Slender wings on supersonic cruise configurations are expected to be thin and highly swept. As a result, edge-separated vortex flow is inevitable and must be accounted for in aerodynamic analysis and design. The present method is based on the method of suction analogy to calculate the total aerodynamic characteristics. The method requires the solution of the attached flow problem, the latter being solved by a low-order panel method in subsonic and supersonic flow. In essence, the lifting pressure is calculated by using a pressure-doublet distribution satisfying the Prandtl-Glauert equation. From the pressure distribution, the leading-edge suction is calculated. The latter is assumed to be the vortex lift through the method of suction analogy. For a cambered wing, the location of vortex-lift action point is important in predicting the aerodynamic characteristics. It is also seen that the effect of camber shape appears nonlinearly in all aerodynamic expressions. To design the camber shape, the camber slope is represented by a cosine Fourier series at each of several spanwise stations. The Fourier coefficients are the design variables. To design a leading-edge flap in the vortex flow (i.e., a vortex flap), the coordinates of corner points and the deflection angle are the design variables. The process of wing design is to determine the camber shape and twist distribution such that an objective function, typically the drag, is minimized, subject to various constraints.

Lan, C. E.↗