Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 829 records · Page 46
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Major Effects of Nonmetallic Inclusions on the Fatigue Life of Disk Superalloy Demonstrated

The fatigue properties of modern powder metallurgy disk alloys can vary because of the different steps of materials and component processing and machining. Among these variables, the effects of nonmetallic inclusions introduced during the powder atomization and handling processes have been shown to significantly degrade low-cycle fatigue life. The levels of inclusion contamination have, therefore, been reduced to less than 1 part per million in state-of-the-art nickel disk powder-processing facilities. Yet the large quantities of compressor and turbine disks weighing from 100 to over 1000 lb have enough total volume and surface area for these rare inclusions to still be present and limit fatigue life. The objective of this study was to investigate the effects on fatigue life of these inclusions, as part of the Crack Resistant Disk Materials task within the Ultra Safe Propulsion Project. Inclusions were carefully introduced at elevated levels in a nickel-base disk superalloy, U720, produced using powder metallurgy processing. Multiple strain-controlled fatigue tests were then performed on extracted test specimens at 650 C. Analyses were performed to compare the low-cycle fatigue lives and failure initiation sites as functions of inclusion content and fatigue conditions. Powder of the nickel-base superalloy U720 was atomized in argon at Special Metals Corporation, Inc., using production-scale high-cleanliness powder-processing facilities and handling practices. The powder was then passed through a 270-mesh screen. One portion of this powder was set aside for subsequent consolidation without introduced inclusions. Two other portions of this powder were seeded with alumina inclusions. Small, polycrystalline soft (Type 2) inclusions of about 50 mm diameter were carefully prepared and blended into one powder lot, and larger hard (Type 1) inclusions of about 150 mm mean diameter were introduced into the other seeded portion of powder. All three portions of powder were then sealed in separate containers, hot isostatically pressurized, extruded, forged into subscale disks, and heat treated. Low-cycle-fatigue specimens were then extracted, machined, and tested. Fatigue tests were performed at 650 C in closed-loop servohydraulic testing machines using induction heating and axial extensometers. All tests were continued to failure, and fractographic evaluations were performed on all specimens to determine the crack initiation sites. A large majority of the failures in specimens with introduced inclusions occurred at cracks initiating from inclusions at the specimen surface, as shown for each type of inclusion in the following bar chart. The inclusions significantly reduced fatigue life from unseeded material levels, as shown in the bar chart. These effects were found to depend on the strain range, strain ratio, and inclusion size. Tests at lower strain ranges and higher strain ratios resulted in larger effects of inclusions on life. Inclusion effects on life were thereby maximized in tests at the lowest strain range of 0.6 percent and the most positive strain ratio of 0.5. Under these conditions, small Type 2 inclusions reduced life substantially-- about 20 times, whereas large Type 1 inclusions dramatically reduced life 100 times. These results clearly demonstrate that it is essential to include the effects of inclusions for realistic predictions of disk fatigue life. Important issues, including temperature dependence, crack initiation versus propagation, surface treatments, realistic disk features and machining, and realistic disk spin testing will be addressed to accurately model inclusion effects on disk fatigue life. Fatigue life varied from well over 105 cycles for no inclusions to a little over 103 cycles for 100-micrometer inclusions. A single crack initiating at a surface-connected seeded inclusion caused failure in each case.

Gabb, Timothy P.↗
DOE OSTI2021

Evaluating the grain-scale deformation behavior of a single-phase FCC high entropy alloy using synchrotron high energy diffraction microscopy

We report although the deformation behavior of high-entropy alloys (HEAs) has been extensively studied at the macroscale, many important properties have yet to be explored for these alloys at the microscale, thus hampering accurate prediction of damage and failure processes. Synchrotron high-energy diffraction microscopy (HEDM) and fast-Fourier transform-based crystal plasticity modeling was conducted to investigate the three-dimensional (3D) grain-resolved micromechanical response for approximately 1,900 constituent grains within a single-phase FCC HEA up to 1% applied strain. The evolution of grain-resolved elastic strains, lattice reorientations, and maximum resolved shear stresses (mRSS) were evaluated to quantify elastic, yield, and fully plastic behavior. Overall, the initial critical resolved shear stress (CRSS), determined via in situ HEDM and companion modeling, was found to be > 20% higher than estimated using the classical polycrystalline Taylor factor (M = 3.06). However, a descriptive parameter based on the average grain-resolved Taylor factor ($\overline{M}$) was found to show excellent agreement with plastic yielding behavior observed within HEDM datasets. Noticeable deviations in HEDM lattice reorientations compared to both EVP-FFT simulations and classical predictions for FCC polycrystals were discovered, highlighting the complexity in correlating local lattice reorientations, Taylor, and Schmid factors with plastic response for this material at the grain-scale. Therefore, it is anticipated that the overall trends and parameter identification of 3D grain-resolved properties in this study can serve as an important foundation for continued mesoscale investigation on both well-established and newly developed Cantor-like HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sn-InAs Nanowire Shadow-Defined Josephson Junctions

Hybrid superconductor–semiconductor platforms are foundational to advancing quantum information technologies, motivating the integration of materials with clean interfaces, robust superconductivity, and scalable architectures. Here, in this work, we report the synthesis and analysis of inclined InAs nanowires, conformally coated with β-Sn shells. These nanowires extend in opposite in-plane directions, forming a self-aligned, criss-cross network. This enables the deterministic formation of nanowire-shadow Josephson junctions through angle-controlled, low-temperature Sn deposition. Structural characterization shows uniform polycrystalline β-Sn shells forming a sharp, diffusion-free interface with InAs. Low-temperature transport measurements reveal a hard induced superconducting gap ≈ 600 μeV, switching currents up to ≈ 500 nA, and parallel magnetic field resilience beyond 1T. These results establish β-Sn/InAs nanowire networks as a promising platform for superconducting qubits, low-noise microwave devices, and the exploration of exotic superconducting phases including triplet pairing and topological superconductivity.

B-Sn↗
DOE OSTI2020

Inelastic neutron scattering study of the anisotropic S = 1 spin chain [ Ni ( HF 2 ) ( 3 – Clpyridine ) 4 ] BF 4

[Ni(HF 2 )(3–Clpyridine) 4 ]BF 4 (NBCT) is a one-dimensional, S = 1 spin chain material that shows no magnetic neutron Bragg peaks down to temperatures of 0.1 K. Previous work identified NBCT as being in the Haldane phase and near a quantum phase transition as a function of D/J to the large-D quantum paramagnet phase (QPM), where D is the axial single-ion anisotropy and J is the intrachain superexchange. Herein, inelastic neutron scattering results are presented on partially deuterated, 11B-enriched NBCT polycrystalline samples in zero magnetic field and down to temperatures of 0.3 K. Comparison to density matrix renormalization group calculations yields D/J = 1.51 and a significant rhombic single-ion anisotropy E (E/D ≈ 0.03, E/J ≈ 0.05). Here, these D, J, and E values place NBCT in the large-D QPM phase but precipitously near a quantum phase transition to a long-range ordered phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2008

Nb(x)Ti(1-x)N Superconducting-Nanowire Single-Photon Detectors

Superconducting-nanowire single-photon detectors (SNSPDs) in which Nb(x)Ti(1-x)N (where x<1) films serve as the superconducting materials have shown promise as superior alternatives to previously developed SNSPDs in which NbN films serve as the superconducting materials. SNSPDs have potential utility in optical communications and quantum cryptography. Nb(x)Ti(1-x)N is a solid solution of NbN and TiN, and has many properties similar to those of NbN. It has been found to be generally easier to stabilize Nb(x)Ti(1-x)N in the high-superconducting-transition temperature phase than it is to so stabilize NbN. In addition, the resistivity and penetration depth of polycrystalline films of Nb(x)Ti(1-x)N have been found to be much smaller than those of films of NbN. These differences have been hypothesized to be attributable to better coupling at grain boundaries within Nb(x)Ti(1-x)N films.

Stern, Jeffrey A.↗
NASA NTRS2009

A Method for Combining Experimentation and Molecular Dynamics Simulation to Improve Cohesive Zone Models for Metallic Microstructures

Fracture processes within a material begin at the nanometer length scale at which the formation, propagation, and interaction of fundamental damage mechanisms occur. Physics-based modeling of these atomic processes quickly becomes computationally intractable as the system size increases. Thus, a multiscale modeling method, based on the aggregation of fundamental damage processes occurring at the nanoscale within a cohesive zone model, is under development and will enable computationally feasible and physically meaningful microscale fracture simulation in polycrystalline metals. This method employs atomistic simulation to provide an optimization loop with an initial prediction of a cohesive zone model (CZM). This initial CZM is then applied at the crack front region within a finite element model. The optimization procedure iterates upon the CZM until the finite element model acceptably reproduces the near-crack-front displacement fields obtained from experimental observation. With this approach, a comparison can be made between the original CZM predicted by atomistic simulation and the converged CZM that is based on experimental observation. Comparison of the two CZMs gives insight into how atomistic simulation scales.

Hochhalter, J. D.↗
DOE OSTI2023

Influence of atomic ordering and cerium doping on magnetostrictive Fe-Al alloys

Magnetostrictive iron-aluminum alloys can be a low-cost, mechanically stable alternative to iron-gallium and rare earth-iron alloys. The magnetostrictive performance of polycrystalline Fe-Al (alfenol) with 13–24 at. % Al was investigated, studying the role of compositional variation and thermal history. It was found that rapid cooling enhances the magnetostrictive response, and peak magnetostriction was found in Fe 78 Al 22 by high temperature annealing followed by quenching. Synchrotron diffraction enabled a direct correlation of magnetostrictive behavior and the transition from short-range order to long-range ordered cluster domains in the material which can be suppressed by rapid cooling. Following recent success of doping Fe-Ga with rare earth elements, we investigated the influence of Ce doping on improving magnetostriction and found that Fe-Al shows negligible solubility for cerium, inhibiting potential magnetostriction enhancement. In conclusion, our results illustrate the complex interplay between phase stability, ordering, and optimized magnetostrictive response.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Spin-Triplet Pairing State Evidenced by Half-Quantum Flux in a Noncentrosymmetric Superconductor

Building future fault-tolerant quantum computers may rely on a basic but so far elusive building-block-type of materials, superconductors with spin-triplet pairing, which were considered to be very rare. Now physicists demonstrate that they can be found in materials with low symmetry, different from most common crystalline materials. The new finding focuses on a particular type of crystals, the structure of which does not have inversion symmetry. For more than a decade, this material class (noncentrosymmetric superconductor) has been inferred to be a potential rich mine of spin-triplet superconductors. It is conceived that the spin-triplet pairing is promised by the broken inversion symmetry, however key experimental evidences remain lacking. Xu et al. applied a newly developed method to examine a prototype noncentrosymmetric superconductor, α-BiPd. Their experiment reveals the presence of the highly unusual half-integer quantization of magnetic flux in polycrystalline rings of α-BiPd, which is a smoking-gun evidence for spin-triplet pairing. This new finding ignites hopes that spin-triplet pairing may be a common presence among the dozens of known noncentrosymmetric superconductors as theoretically expected, which can now be unambiguously identified by the unique phenomenon of half-quantum magnetic flux.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1980

Effect of UV irradiation on evaporated ZnS films

Evaporated ZnS films used as a component in reflectance enhancing or decreasing multilayer coatings for mirrors, transparent optical materials, and vacuum UV reflecting optics, are investigated with reference to the reflectance loss under UV irradiation and the formation of ZnO as a result of the decomposition of ZnS in the presence of oxygen. Reflectance measurements over a broad wavelength range reveal that the UV induced reflectance losses are generally restricted to wavelengths shorter than 4000 A and are most severe in the vacuum UV region. After 134 hr of UV exposure initially polycrystalline film of 150-200 A thick is completely converted to amorphous ZnO. The results demonstrate that caution should be exercised in employing ZnS as the outer layer in an optical coating system designed for use in the UV and vacuum UV regions.

Hass, G.↗
DOE OSTI2026

From Serendipity to Exploration: Synthesis and Properties of PtSiSb

PtSiSb is a compound with covalent Si–Sb bonds, which are relatively rare instances in solid-state materials. The original report on PtSiSb indicates synthetic challenges for the isolation of single-phase samples, as well as potential discrepancies in the predicted electronic structure and experimental transport properties. In this work, we considered PtSiSb as a case study with the objective of demonstrating the importance of synthesis as a bridge between theoretical predictions and experimental properties. Using guidance from in situ powder X-ray diffraction, the synthesis of single-phase polycrystalline samples was developed, allowing further experimental characterization of transport and catalytic properties. Thermal conductivity and heat capacity demonstrated anomalous behavior, indicating an unconventional phonon scattering mechanism in PtSiSb. Charge transport measurements indicated semimetallic behavior. Hydrogen evolution reaction (HER) tests in acidic electrolyte revealed that the PtSiSb cathode needs an overpotential η 10 = 120 mV to achieve a current density j = −10 mA/cm 2 . This is lower activity than elemental Pt but comparable to known and active transition-metal phosphide HER catalysts, such as CoP, with η 10 = 93 mV when measured at identical conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Radiation-Induced Changes in Single Crystal Calcite and Dolomite: Mineral Analogues of Light Water Reactor, Nuclear Power Plant Concrete Aggregates

Two analogues of aggregates (calcite and dolomite) found in nuclear power plant (NPP) concrete have been neutron irradiated to fluences up to 2 × 10 20 n/cm 2 at 52 °C and 4 × 10 19 n/cm 2 at 95 °C (E > 0.1 MeV). X-ray diffraction studies showed that these aging conditions affected crystallography of both calcite and dolomite, with both showing a growth in their unit cells compared to that of the unirradiated samples. Only dolomite samples showed a continuous increase of its lattice parameters with the increase in irradiation. In calcites, the lattice growth with irradiation dissipated after a fluence of 5 × 10 18 n/cm 2 . Radiation-induced disordering of the crystal structure was observed in both materials, while a healing effect of irradiation temperature was mainly observed in calcites. Dislocation densities calculated by using XRD data also supported these observations. Insights made into the unit cells of both minerals by using Fourier synthesis showed that the Mg sites are more prone to the neutron irradiation than the Ca sites, resulting in larger radiation effects and higher disruption in the crystal structure of dolomite than that of calcite. Furthermore, other than the polycrystalline characteristics observed by using TEM, these minerals did not show complete amorphization or significant structural decomposition at the studied irradiation fluences.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Enabling full-scale grain boundary mitigation in polycrystalline perovskite solids

There exists a considerable density of interaggregate grain boundaries (GBs) and intra-aggregate GBs in polycrystalline perovskites. Mitigation of intra-aggregate GBs is equally notable to that of interaggregate GBs as intra-aggregate GBs can also cause detrimental effects on the photovoltaic performances of perovskite solar cells (PSCs). Here, we demonstrate full-scale GB mitigation ranging from nanoscale intra-aggregate to submicron-scale interaggregate GBs, by modulating the crystallization kinetics using a judiciously designed brominated arylamine trimer. The optimized GB-mitigated perovskite films exhibit reduced nonradiative recombination, and their corresponding mesostructured PSCs show substantially enhanced device efficiency and long-term stability under illumination, humidity, or heat stress. The versatility of our strategy is also verified upon applying it to different categories of PSCs. Our discovery not only specifies a rarely addressed perspective concerning fundamental studies of perovskites at nanoscale but also opens a route to obtain high-quality solution-processed polycrystalline perovskites for high-performance optoelectronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Metallic transfer between metals in sliding contact examined by auger emission spectroscopy

Metallic transfer between polycrystalline metals in sliding contact was examined. Hemispherical riders of iron, nickel, and cobalt were slid on tungsten, tantalum, niobium, and molybdenum disks in ultrahigh vacuum. Auger emission spectroscopy was used to monitor the elemental composition of the disk surfaces. Iron, nickel, and cobalt transferred to tungsten, whereas only cobalt transferred to tantalum, niobium, and molybdenum. The results of this investigation are discussed in terms of the cohesive energy and strain hardening characteristics of the specimen materials.

Pepper, S. V.↗
DOE OSTI2021

Electrical and Thermal Performance of Ga₂O₃–Al₂O₃–Diamond Super-Junction Schottky Barrier Diodes

The design space of Ga 2 O 3 -based devices is severely constrained due to its low thermal conductivity and absence of viable p-type dopants. In this work, we discuss the limits of operation of a novel Ga 2 O 3 –Al 2 O 3 –diamond-based super-junction device concept, which can alleviate the constraints associated with Ga 2 O 3 -based devices. The improvements achieved using the proposed device concept are demonstrated through electrical and thermal simulations of Ga 2 O 3 –Al 2 O 3 –diamond-based super-junction Schottky barrier diodes (SJ-SBDs) and non-punch-through or conventional Schottky barrier diodes (NP-SBDs). The SJ-SBD enables operation below the R ON -breakdown voltage limit of Ga 2 O 3 NP-SBD, enabling >4 kV blocking voltage at R ON of 1–3 mΩ cm 2 . Here, the maximum switching frequency of SJ-SBD may be only a few kHz, as it is limited by the activation energy of acceptors (0.39 eV) in the diamond. Crucially, compared with NP-SBD, the use of diamond also results in ~60% reduction in temperature rise during static power dissipation. Polycrystalline diamond (PCD) properties depend on detailed microstructure and benefits compared to ideal Ga 2 O 3</sub NP-SBD arise for diamond critical fields ≥6 MV/cm and thermal conductivities as low as 50–150 W/(m • K).

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Thermo-Elastic Properties and Damping of U-6wt%Nb

While thermal expansion data exists for quenched (as well as aged) U-6wt%Nb, there is wide variation in the reported room temperature elastic moduli. To better understand the room temperature elastic behavior and to address the complete absence of data on the temperature dependence of the elastic moduli, room temperature and in-situ elevated temperature resonant ultrasonic spectroscopy (RUS) was performed along with x-ray diffraction (XRD) and dilatometry using a thermomechanical analyzer (TMA). An in-situ small- and wide-angle x-ray scattering (SAXS/WAXS) experiment was performed on a companion sample to help interpret the results. The room temperature polycrystalline dynamic moduli were measured to be E = 95.4 ± 4.5 GPa and G = 35.2 ± 0.2 GPa, respectively. As the temperature is raised, the stiffness slowly decreases, consistent with the empirical rule proposed by Varshni, up to the point of precipitation of the equilibrium α-U phase, which is stiffer than the martensitic phases. Homogenization theory of composites can be used to rationalize the observed response at high temperatures and after high-temperature exposures. Further, aging of the material at low temperatures (≤200°C) does not affect the linear elastic stiffness, but does impact the damping behavior which can be measured through RUS. This change in damping provides another perspective on the microstructure changes induced by low-temperature aging which also result in significant strengthening.

36 MATERIALS SCIENCE↗
NASA NTRS2005

New Deep Reactive Ion Etching Process Developed for the Microfabrication of Silicon Carbide

Silicon carbide (SiC) is a promising material for harsh environment sensors and electronics because it can enable such devices to withstand high temperatures and corrosive environments. Microfabrication techniques have been studied extensively in an effort to obtain the same flexibility of machining SiC that is possible for the fabrication of silicon devices. Bulk micromachining using deep reactive ion etching (DRIE) is attractive because it allows the fabrication of microstructures with high aspect ratios (etch depth divided by lateral feature size) in single-crystal or polycrystalline wafers. Previously, the Sensors and Electronics Branch of the NASA Glenn Research Center developed a DRIE process for SiC using the etchant gases sulfur hexafluoride (SF6) and argon (Ar). This process provides an adequate etch rate of 0.2 m/min and yields a smooth surface at the etch bottom. However, the etch sidewalls are rougher than desired, as shown in the preceding photomicrograph. Furthermore, the resulting structures have sides that slope inwards, rather than being precisely vertical. A new DRIE process for SiC was developed at Glenn that produces smooth, vertical sidewalls, while maintaining an adequately high etch rate.

Evans, Laura J.↗