Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SCANNING ELECTRON MICROSCOPY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

The anode supported internal cathode tubular solid oxide fuel cell: Novel production of a cell geometry for combined heat and power applications

An effective strategy for generating combined heat and power (CHP) systems is to use the combustion of hydrocarbons to provide fuel reforming and heat production for solid oxide fuel cell (SOFC) operation. Though tubular SOFCs (tSOFCs) are well suited to the thermal cycling associated with combustion systems, they have a geometric limitation which requires significant alteration to the combustion chamber. These alterations can be eliminated by producing an anode supported internal cathode-tSOFC (IC-tSOFC) which can be directly integrated into the chamber with minimal alterations. Novel methods used to produce IC-tSOFCs are discussed in this work. Scanning electron microscopy (SEM) and performance characterization are used to analyze fabricated cells. Finally, with a peak power density of 369 mW∙cm –2 , and an open circuit voltage (OCV) of 0.98 V, it is confirmed that novel production methods for IC-tSOFCs have been successful.

08 HYDROGEN↗
DOE OSTI2022

Reticulated porous lanthanum strontium manganite structures for solar thermochemical hydrogen production

Porous ceramic foams are utilized in various fields and applications due to their advantageous properties such as high porosity, high specific surface area, and controlled permeability. Non-stoichiometric oxide foams are of particular interest for the solar thermochemical production of hydrogen in directly irradiated solar receivers due to their enhanced heat transfer capabilities and structural integrity. Here we report the fabrication of lanthanum strontium manganite replica foams and their solar thermochemical water splitting performance. Highly porous (>80%) foams were produced with controlled structure and tested in a high temperature water splitting furnace to demonstrate stability and overall performance. The temperature profile of the burnout and sintering of the foam structure were altered based on simultaneous differential scanning calorimetry and thermal gravimetry analysis. Two-step sintering was used both to retain micron-sized pores (D50 = 0.4 μm) on the foam's struts and to limit grain growth to a grain size of ~1 μm. The structural characteristics were confirmed by porosimetry and scanning electron microscopy. The foams were repeatedly cycled, producing approximately 200 μmol/g of H 2 per cycle. Water splitting performance was tested for 50 cycles and approximately 35 h at 1400 °C. No statistical difference in the effective hydrogen production per cycle was observed, which is promising for long-term redox cycle stability.

08 HYDROGEN↗
DOE OSTI2023

Improved catalytic activity of Mo x Ni y Al z thin films as electrocatalyst for hydrogen evolution reaction in alkaline media

In this work, we report activities of Mo x Ni y X z (where X is Al, Co, Cr, Cu, Fe, W)-based electrocatalysts for hydrogen evolution reaction (HER) in a 1 M NaOH solution. Mo x Ni y X z thin film electrocatslysts were prepared by magentron sputtering at 25°C and 800°C and characterized by scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) analysis. Here, the catalytic activity of electrocatalyst was studied by cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalyst based on Mo 80 Ni 5 Al 15 (800°C) shows the best value of the overpotential (-181 mV) for HER from all tested ternary systems. XRD analysis indicates that HER activity only Mo 80 Ni 5 Al 15 thin films prepared at 800°C contained fcc phase. Other less active composition contained only bcc phase. The results obtained from impedance spectroscopy are consistent with the results from cyclic voltammetry. The stability of the prepared catalyst was studied by chronoamperometric analysis. The results from chronoamperometry show that HER activity of Mo 80 Ni 5 Al 15 prepared at 800°C, after very slight initial activity decrease, stays constant, while activity of Ni catalyst decreased almost twice in measured time window. Since Ni is commonly used industrial catalyst, Mo 80 Ni 5 Al 15 based alloy could be more attractive catalyst material for alkaline electrolyzers.

08 HYDROGEN↗
DOE OSTI2026

Mechanism of H 2 plasma-enabled reduction of hematite thin films

Hydrogen plasma is gaining significant interest as a promising pathway for direct iron ore reduction and for lowering process temperatures but the reduction mechanism remains poorly understood. In this work we analyzed the plasma and thermal reduction of thin-film hematite (Fe 2 O 3 ) at temperatures below 340 °C using X-ray diffraction and scanning electron microscopy with energy-dispersive X-ray spectroscopy. Plasma reduced the incubation period by an order of magnitude and increased the reduction rate by a factor of 2.6 compared to thermal reduction. Plasma-produced H-atoms facilitate the formation of numerous iron nucleation sites, bypassing the energetically unfavorable dissociative adsorption of H 2 on iron oxide. These iron nuclei can autocatalyze the reduction of the surrounding hematite via a hydrogen spillover mechanism. Our results demonstrate that plasma-derived H-atoms primarily impact the initial nucleation-limited stage. These new insights provide a mechanistic framework that can aid the implementation and optimization of hydrogen plasma-assisted iron oxide reduction at reduced temperatures.

08 HYDROGEN↗
DOE OSTI2022

Studying the effect of drug-to-excipient ratio on drug release profile for drug coated balloons

Drug-coated balloons (DCB) have emerged as the alternative procedure for restenosis because of their ability to treat a variety of occlusion types with a uniform dose of anti-proliferative drugs. DCB are balloons coated with antiproliferative drugs encapsulated in a polymer matrix. There are several types of coating matrices used to produce DCB. In this study, the relationship between coating composition and drug release under physiologically relevant conditions was examined to understand how differences in coating composition impacts the drug transfer from the balloon surface to the simulated body fluids. To conduct the experiments, the balloons were coated with different paclitaxel (drug)-to-iopromide (excipient) ratios (3:1, 3:2 and 1:2) using an in-house developed micro-pipetting method. Scanning electron microscopy (SEM) images showed that the 3:1 PTX:IOP ratio produced a more uniform, crystalline microstructure with a thinner coating throughout the balloon surface compared to the other drug-to-excipient ratios. The 1:2 PTX:IOP ratio showed the least crystalline microstructure among the three ratios evaluated in this study. Three different drug elution conditions were tested. The amount of drug released to the medium was quantified by high performance liquid chromatography (HPLC). Our soaking study and submerge & deploy study showed that ~20% of the drug transferred to the target site under physiological conditions. A track and deploy method was performed using a “mock” artery, to simulate an in vitro environment. Coated balloons were passed through the mock artery to mimic tracking turns the balloon within the arteries during the angioplasty procedures. Seven elution samples were collected at different stages of the procedure. Finally, drug release results suggest that the higher excipient ratio helps to deliver the lipophilic drug to the target site under simulated conditions but causes higher drug loss during the balloon transfer process.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2020

Quantifying the resistance to dislocation glide in single phase FeCrAl alloy

The resistance to dislocation glide associated with slip systems {110}<111> and {112}<111> in single phase FeCrAl alloy is measured via micromechanical testing in a scanning electronic microscopy at room temperature. Two important factors, the shape and orientation of a pillar, are discussed with respect to the glide resistance and stress-strain response. Maximizing Schmid factor of one specific slip system while minimizing others is recommended in order to diminish obvious dislocations-induced hardening during in-situ testing. Apparent Schmid factor analysis is conducted to select grains with preferred orientations. Two types of pillars with conventional cylindrical shape or dog-bone shape are tested under compression to estimate the resistance to dislocation glide and evaluate the effect of pillar shape on the compression stress-strain response. One dog-bone pillar is tested under tension to check the tension-compression isotropy of dislocation slip. We discover that the shape of a pillar to a smaller extent affects the measured resistance but strongly influences the stress strain response. Cylindrical pillars exhibit apparent hardening associated with early yielding due to stress or strain concentration at contact region, while dog-bone pillars show an obvious yielding and continuous shearing without hardening. The resistance is 220 MPa for slip system {110}<111> and 230 MPa for slip system {112}<111>. Finite element analysis is performed to account for the influence of pillar shape and contact condition on mechanical response.

36 MATERIALS SCIENCE↗
DOE OSTI2022

From ammonium Hexahalorhenates(IV) to nanocrystalline rhenium metal: A combined thermal, diffraction and microscopic analysis

Rhenium metal powder is a material of industrial importance. Several industrial and laboratory methods have been developed for the preparation of ultrafine Re metal powder and nanoparticles. The present study provides a better understanding of the characteristic and formation of Re metal powder from the decomposition of (NH4)2ReX6 salt (X = F, Cl, Br, I) at high temperature in inert atmosphere. Such analysis resulted in the formation of nanocrystalline Re metal as characterized by powder XRD. Williamson-Hall, Scherrer, and Williamson-Smallman methods were employed to study the effect of crystallize size, lattice strain, and dislocation density as analyzed from powder XRD peak broadening. Here, the morphology and composition of the metal were analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Pectin-associated mannans and xylans play distinct roles in cell-cell adhesion in pine and poplar wood

Wood particles of pine required longer treatments of acidic chlorite and dilute alkali to achieve similar proportions of cell separation as of poplar. Chemical extraction and enzymatic digestion studies indicated that rhamnogalacturonan-I (RG-I), mannan and xylan contribute to cell-cell adhesion in pine wood. Mannan associated with lignin in an acidic chlorite fraction and with xylan in a dilute alkali fraction. RG-I and xylan were extracted in both chlorite and dilute alkali in poplar. Scanning electron microscopy and a probe diffusion study using Fluorescence Recovery After Photobleaching showed that lignin, RG-I and mannan initiated cell separation at cell corners and dilute alkali extraction of xylan was required for complete cell separation in pine. Cell-cell separation increased enzymatic saccharification within 24 h by 2-fold in poplar and 3.4-fold in pine. Finally, our results inform a strategy to reduce particle size in woody biomass and provide insights into different molecular bases of cell-cell adhesion.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Microwave-assisted pyrolysis of liquid hydrocarbons using iron-based alumina catalysts obtained by solution combustion synthesis: The effect of synthesis parameters

The microwave-absorbing and catalytic properties of iron-based alumina (FeAl x O y ) materials have enabled their use as catalysts for the microwave-assisted generation of hydrogen and carbon via pyrolysis of hydrocarbons. Solution combustion synthesis (SCS) is a promising method to fabricate these materials, but the pyrolysis performance still needs to be improved. The present work investigated how altering the SCS parameters affects the pyrolysis of diesel fuel, gasoline, and crude oil. Two fuels (citric acid and glycine), four Fe:Al molar ratios, and two heating modes (hotplate and furnace) were tested. Fe/γ-Al 2 O 3 and Fe/β-SiC catalysts were prepared via incipient wetness impregnation for comparison. Among the three fossil fuels tested, diesel fuel yielded the highest amounts of H 2 and least amounts of CO x . The choice of fuel for the SCS process and the Fe/Al ratio strongly affected pyrolysis performance as they influence properties important for both catalysis and microwave absorption. The use of glycine resulted in catalysts that exhibited high H 2 yield and low CO 2 generation, which is explained by the revealed structural differences. The increase in the Fe:Al molar ratio accelerated microwave heating by adding more magnetic loss but also increased the amount of CO x . When the optimal SCS parameters were used, FeAl x O y catalysts outperformed Fe/γ-Al 2 O 3 and Fe/β-SiC. The high H 2 generation efficiency of the SCS catalysts is explained by their enhanced microwave-absorption properties. Scanning electron microscopy and energy dispersive X-ray spectroscopy revealed the formation of large-diameter CNTs via the tip-growth mechanism. The regeneration of SCS catalysts was demonstrated via the Boudouard reaction.

Carbon nanotubes↗
DOE OSTI2026

The evolution of coal porosity during pyrolysis

Gasification of coal, municipal waste, or other organic materials is a potential hydrogen source that entails complex thermal decomposition and transport processes. This study provides a multiscale analysis of these processes for sub-bituminous (Usibelli, Healy, Alaska) and lignite (Center, North Dakota) coals and provides data useful for process design. The chemistry, mineralogy, and pore structures of pyrolyzed coal and their evolution with thermal decomposition are discussed. Samples pyrolyzed at 200–1000 °C were analyzed by small-angle neutron scattering; ultra-small, small-, and wide-angle X-ray scattering; and other complementary techniques. Scanning electron microscopy showed new pores in the high-temperature-pyrolyzed material. Upon heating, the coals became progressively denser, and the concentration of hydrogen decreased. Changes in pore volume fell into three temperature ranges: an initial, low-temperature range that, for the Usibelli coal, involved an increase in overall porosity; a mid-temperature range associated with pore volume loss; and a high-temperature range associated with significant porosity increase and char formation. This transformation was paralleled by changes in fractal dimension and correlation length. The higher the pyrolysis temperature the greater the small-pore-volume fraction and overall surface area became. Pyrolysis increased the lateral size of coal crystallites, decreased the amorphous fraction, and increased the aromatics fraction and overall coal rank. Comparisons of neutron and X-ray scattering data and subsequent water uptake studies showed that pre-dried coals can re-hydrate relatively rapidly upon exposure to air, which can significantly affect the porosity calculated from small-angle-scattering data. Fits to the cumulative porosity curves provide a method for modeling the physical and chemical transformation of hydrogen-containing feedstock during gasification.

Anovitz, Lawrence {Larry} [ORNL] (ORCID:0000000226↗
DOE OSTI2021

The role of Si in determining the stability of the θ; precipitate in Al-Cu-Mn-Zr alloys

Precipitate-strengthened Al-Cu-Mn-Zr (ACMZ) alloys demonstrate improved microstructural stability compared to conventional Al-Cu alloys. Si is typically considered an impurity in these alloys, but a systematic analysis of ACMZ alloys with a range of Si levels revealed that there is a Si content range (~0.05 wt. % < Si < ~0.10 wt. %) for achieving optimal high temperature microstructural stability. A combination of hardness testing, scanning electron microscopy, and atom probe tomography has been used to understand the relationship between Si content, aging response, and thermal stability in ACMZ alloys. It is shown that the optimum Si content range corresponds to a reduced as-aged hardness, but a greater hardness value retained by the alloy after thermal exposure to 350 °C for 200 hours. A mechanism is proposed in which optimum Si levels reduce the number density of nucleation sites for θ' precipitates, resulting in larger precipitates that, on average, provide a reduced as-aged strength but are more coarsening resistant. This inherent θ' coarsening resistance allows more time for slow-diffusing Mn and Zr to reach the θ' interface and further stabilize the precipitates. Designing the optimal as-aged microstructure for improved thermal stability of the alloy by controlling impurity levels is a concept that has implications beyond the investigated Al-Cu alloy system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spark plasma sintered, MoNbTi-based multi-principal element alloys with Cr, V, and Zr

MoNbTi, MoNbTiZr, CrMoNbTiZr, and MoNbTiVZr multi-principal element alloys (MPEAs) were fabricated via spark plasma sintering (SPS) and investigated for use in high-strength applications. The fabrication method by SPS and powder metallurgy differs from those presented in the prior literature, where most MPEAs are fabricated using arc melting (AM) methods. Here cryogenic milling was used to maximize potential defect sinks (grain boundaries) for radiation resistance and to increase ultimate tensile strength through the Hall-Petch effect. SPS was chosen for consolidation in order to maintain a fine-grained structure during densification. Each alloy was characterized using x-ray diffraction and scanning electron microscopy for phase identification and compositional homogeneity. The base ternary alloy MoNbTi presented a predominantly single BCC system with minor cubic phases. The introduction of additional alloying elements—Zr, V, and Cr—heightened the phase complexity and increased the fractions of a secondary BCC phase and an HCP phase from Zr. The addition of Cr induced a larger fraction of the Laves phase to form. The addition of V caused the precipitation of small Mo inclusions. Thermodynamic analysis was performed to understand the separation of phases in each alloy. Discrepancies among the phase predictions generated by thermodynamic models, phases previously presented in the literature, and the characterization results suggest that MPEA fabrication methods, especially solid-state methods, require significant investigation to ensure that alloys can remain stable throughout their anticipated service lifetimes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution and intermetallic formation in Zn-3Mg (wt%) powder mixture processed by high-pressure torsion

Severe plastic deformation (SPD) techniques have been used extensively over the past 40 years for producing strong metals and alloys. High-pressure torsion (HPT) is one of the most promising SPD techniques for achieving high strength through nanoscale grain refinement and phase transformation. In this research, a mixture of pure zinc (Zn) and magnesium (Mg) powders, Zn-3Mg (wt%), was HPT-processed under a pressure of 6 GPa for 1, 5, 10, 20, and 30 turns at room temperature to achieve a high strength biodegradable material. In order to understand the effects of pre-consolidation on the resulting microstructure and hardness, HPT processing was performed on loose powders placed in the die and also on a pre-compacted powder mixture and the resulting HPT disks were characterized by X-ray diffraction, scanning electron microscopy, atom probe tomography, and Vickers microhardness. In both cases, the HPT disk microstructures contained nanoscale grains, and stable and metastable strain-induced intermetallics, but an unusual softening appeared at large shear strains. Grain size, grain morphology, and the formation of different intermetallics were analyzed to explain the unusual hardness distribution, and it was found that an inverse Hall-Petch relationship between hardness and grain size exists. It is suggested that thermally-activated phenomena such as grain boundary sliding contributed to the strain-induced softening of this nano-structured biomaterial due to its low melting point. Finally, the current results are compared with those for HPT-processed cast alloys and hybrids of the same composition.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural features underpinning the mechanical behavior of powder metallurgy Cr-based alloys

Refractory materials such as Cr-based alloys offer the potential of enhanced elevated temperature performance but have been limited by their poor formability. However, powder metallurgy has been shown to be a viable pathway to fabricate these alloys. Nanophase separation sintering (NPSS) in particular has been used in the literature to accelerate the densification of powder metallurgy Cr- and W-based alloys. Here, we explore microstructure evolution during NPSS in a binary Cr 85 Ni 15 alloy consolidated via (i) cold pressing & pressureless sintering and (ii) hot isostatic pressing followed by hot extrusion & hot upsetting, and the role of these different processing routes on resulting material properties. The alloy lacked room temperature tensile ductility regardless of consolidation process, with multi-length scale characterization, including scanning electron microscopy, transmission electron microscopy, atom probe tomography, X-ray diffraction, and uniaxial tensile testing, revealing that brittleness was due to intrinsically poor Cr grain boundary cohesion. Tensile testing conducted at 760 °C showed marked strength reduction for the extruded & upset (94 %) condition compared to the pressed & sintered (18 %). The formation of orthorhombic CrNi 2 intermetallics functioned as precipitate strengtheners and prevented elevated temperature softening in the pressed and sintered condition. The findings offer foundational insights into aiding the future development of Cr-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Diffusion and phase formation in the γ-uranium-technetium system

Phase formation in the U-Tc binary system at 800 °C was investigated using a diffusion couple experiment. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) identified four novel potential intermetallic phases - U 7 Tc 3 , U 13 Tc 12 , U 3 Tc 5 , and UTc 4 . Diffusion coefficients were calculated for the intermetallic phases using the Boltzmann-Matano method and were respectively found to be – 120, 38.2, 15.6, and 1.51 × 10 −18 m 2 /s. Tc also exhibits a solid-solution phase with high penetration into the U with a diffusion coefficient of ∼ 10 −14 m 2 /s. Furthermore, these findings expand the number of known U-Tc phases and provide the first diffusion coefficients for the U-Tc system, and contribute valuable data to the broader field of actinide metallurgy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Unseeded, spontaneous nucleation of spherulitic magnesium calcite

Most of the sedimentary carbonates deposited in the marine environments are composed of calcium carbonate minerals with varying amounts of incorporated Mg 2+ . However, understanding how interactions of impurities with carbonate and their incorporation affect sediments behavior remains a challenge. Here, a new insight is obtained by monitoring solution composition, morphology, and electrokinetic potential of carbonate particles formed in a spontaneous unseeded batch precipitation experiment using electrochemical and scanning electron microscopy methods. The solid composition and growth rate are extracted from changes in the bulk composition and fitted to chemical affinity rate law, revealing that the precipitation pathway consists of second-order dissolution and first-order precipitation. The molecular dynamics simulations show that the lattice strain induced by randomly substituting Ca 2+ by Mg 2+ stabilizes spherical nanoparticles and reduces their surface area and volume. Combining kinetics and thermodynamics insight, we conclude that variation in the carbonate bulk and interfacial energies, along with the solution supersaturation, lead to the dissolution-precipitation transformation pathway from Mg-rich to Mg-poor carbonate phase that preserves spherulitic morphology. Furthermore, our findings are relevant for long-standing questions of how impurities influence diagenesis of carbonate sediments and spherulitic carbonate particles' origin.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Dendrite-free Al recycling via electrodeposition using ionic liquid electrolytes: The effects of deposition temperature and cathode surface roughness

In this report, the electrodeposition of Al from aluminum scrap alloys (A2020) on copper cathode substrates with varied surface roughness under different deposition temperatures was studied using low-temperature AlCl 3 -1-butyl-3-methyl-imidazolium chloride (BMIC) ionic liquid electrolytes. The bulk electrodeposition of Al was carried out under a voltage of 1.5 V at a stirring rate of 120 rpm using a fixed ionic liquid electrolyte concentration (molar ratio AlCl 3 : BMIC = 2:1). The effects of deposition temperature (range from 80 °C to 140 °C) and surface roughness of Cu cathode substrates (polished by 320, 600, 800, 1200 grits SiC sandpapers and mirror polishing process) on the morphology of deposited Al, current density, current efficiency and energy consumption, were investigated. The Al deposits were characterized using scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), profilometer, and electrochemical measurements for current density, current efficiency, and energy consumption. It is demonstrated that the deposition temperature and surface roughness of Cu electrodes play a critical role in the nucleation and growth of Al deposits. Higher deposition temperature promotes the diffusion and/or migration of Al 2 Cl 7 - ions and then enhances the current density and efficiency during the electrodeposition of Al. Smoother surface of Cu electrodes is preferred for the formation of dendrite-free Al deposits. Typically, on the mirror polished Cu electrode, no Al dendrite structure was observed, and only plate-like Al deposits were formed at the deposition temperature of 100 °C. Pure metallic Al was successfully deposited on Cu electrodes in AlCl 3 + BMIC ionic liquid electrolytes for all experiments with a current efficiency range from 72% to 99% and energy consumption of 4.6–6.3 kW h/kg Al.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Spectral induced polarization signatures of smoldering remediation enhanced with colloidal activated carbon: An experimental study

Monitoring the remediation of soil and groundwater contaminated by organic compounds remains highly challenging. The spectral induced polarization (SIP) method exhibits significant promise for monitoring changes to the electrical properties of soils that are undergoing remediation. Thermal treatments, such as smoldering combustion, have become established remediation techniques for destroying contaminants. Smoldering combustion is now being supported by colloidal activated carbon (CAC), with CAC able to adsorb contaminants and supplement the fuel source for destroying contaminants. The objective of this study is to investigate the potential of SIP for tracking the smoldering remediation of imitated field soils supplemented with CAC. SIP column experiments were first conducted to assess the response of SIP to varying concentrations of CAC in field soils that contain, or do not contain, organic material (OM). Here these results demonstrate that increasing OM and CAC contents increase both the real and imaginary components of the complex conductivity, with the imaginary conductivity also showing frequency dependence. Next, a suite of smoldering and SIP column experiments was conducted to investigate if SIP can detect changes in imitated field soils of varying OM and CAC contents that have been remediated by smoldering combustion. The SIP results on the examined soils both before and after smoldering show that SIP can detect changes in the real conductivity, and particularly the imaginary conductivity, between different soil compositions and different stages of the remediation process. High resolution scanning electron microscopy (SEM) imaging was performed on all samples to validate the SIP and smoldering experiments, confirming significant reductions in carbon after smoldering. Overall, this study suggests that SIP has potential to detect changes in the electrical properties of field soils due to the addition of remedial fluids like CAC and contaminant destruction by smoldering remediation.

54 ENVIRONMENTAL SCIENCES↗