Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CASTINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 811 records · Page 45

As cast precipitation microstructures in twin-roller melt-spun Cu{sub 90}Co{sub 10} alloys

As cast Cu{sub 90}Co{sub 10} ribbons rapidly solidified by twin-roller melt spinning, exhibit special microstructure features. This processing method provides scenarios where a different phase selection takes place; coherent Co precipitates form directly from solidification, with neither a spinodal-like composition oscillation nor a discontinuously precipitated laminar phase. Samples are processed at tangential wheel speeds of 10 m/s (V10), 15 m/s (V15), 20 m/s (V20) and 30 m/s (V30). Microstructures resulting from this single step process are characterized and the hysteresis properties and the magnetoresistance effects evaluated. Samples V30 have a quite uniform density of coherent precipitates, with a narrow size distribution around 4 nm. On contrary, non-uniform precipitate distributions are found in samples cooled at lower rates; zones with a high density of coherent Co-rich precipitates are found forming colonies. These colonies are consistent with the extended compositional fluctuations occurring during very early stages in the cooling process. Samples may exhibit wide (V10) and even bimodal (V15) size distributions. Only samples V30 behave close to the ideal superparamagnetism. Samples V20 present relatively large coercivity and relative remanence and behave as an interacting superparamagnet, while the hysteresis loops of ribbons cooled at lower rates exhibit a ferromagnetic contribution in addition to the superparamagnetic-like one. This ferromagnetic component arises from blocked precipitates, larger than the upper bound size for superparamagnetic behavior at 300 K (12 nm). Room temperature magnetoresistance values associated to granular scattering units decrease as the mean precipitate size increases, but they remain below 2%, which is lower than that measured in samples annealed after rapid solidification, indicating that in this latter case contributions from the spinodally segregated matrix take place in addition to that of Co granules. - Highlights: •Microstructures of twin-rolled Cu{sub 90}Cu{sub 10} alloys are for the first time characterized. •Coherent Co-rich precipitates distribute forming dense colonies inside the grains. •No coexisting multilayer-like structures (spinodal or laminar phases) are detected. •Magnetic hysteresis arises from inter-particle interaction in these dense colonies. •Magnetoresistance level in these purely granular systems is low (1.6% at 300 K).

36 MATERIALS SCIENCE↗

The partial substitution of Y with Gd on microstructures and mechanical properties of as-cast and as-extruded Mg-10Zn-6Y-0.5Zr alloy

Highlights: • The as-extruded Mg-10Zn-6Y-0.5Zr and Mg-10Zn-3Y-3Gd-0.5Zr alloys show bimodal microstructure and DRXed microstructure. • In addition to W phase, Icosahedral quasicrystal phase layer is observed at the surface of some W phase particles in as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt. %) alloy. • The as-extruded Mg-10Zn-6Y-0.5Zr (wt. %) alloy exhibits TYS of 341 MPa, UTS of 368 MPa and elongation to failure of 6.8%. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt. %) alloy shows lower TYS of 247 MPa, UTS of 330 MPa and higher elongation to failure of 19.8%. - Abstract: Mg-10Zn-6Y-0.5Zr (wt%) alloy and Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy with medium RE content have been fabricated by conventional casting and indirect extrusion. The as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy shows a bimodal microstructure containing dynamic recrystallized (DRXed) grains with average grain size of 2 μm and deformed regions. In addition to the fragmented W phase particle bands distributing along the extrusion direction, large amount of nano W phase and small amount of nano β{sub 2}′ phase are precipitated in the matrix. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy exhibits completely dynamic recrystallized microstructure with average grain size of 3 μm. The broken W phase particles are distributed homogeneously in the matrix. Icosahedral quasicrystal phase layer is observed at the surface of some W phase particles in the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr alloy. The as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy exhibits yield strength of 341 MPa, ultimate tensile strength of 368 MPa and elongation to failure of 6.8%. While the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr (wt%) alloy shows lower yield strength of 247 MPa, ultimate tensile strength of 330 MPa and higher elongation to failure of 19.8%. The higher strength in the as-extruded Mg-10Zn-6Y-0.5Zr (wt%) alloy is mainly attributed to higher area fraction of unDRXed regions with strong texture and the precipitation of nano W and β{sub 2}′ phase. The fully recrystallized microstructure with weak texture and the formation of icosahedral quasicrystal phases with good coherent bond with α-Mg contribute to the good ductility of the as-extruded Mg-10Zn-3Y-3Gd-0.5Zr alloy.

36 MATERIALS SCIENCE↗

Secondary recrystallization behavior in strip-cast grain-oriented silicon steel processed by isothermal secondary annealing

Highlights: • Abnormal grain growth was successfully developed after annealing at 1025 °C for 15 min. • The formation mechanism of the Goss and {110}<227> secondary grains was elucidated. • Retention of matrix grain colonies in the interior or at the grain boundaries of secondary grains was explained. - Abstract: The primary annealed sheets of strip-cast grain-oriented silicon steel were isothermally secondary annealed for 15 min under 100% H{sub 2} atmosphere. The microstructure and crystallographic orientation at different annealing temperatures were characterized and the secondary recrystallization behavior was elucidated. It was observed that relatively complete abnormal grain growth occurred at 1025 °C. Incomplete abnormal grain growth developed when the temperature was lower than 1025 °C, and normal grain growth occurred when the temperature was higher than 1025 °C. During the abnormal grain growth, both of the Goss and {110}<227> grains developed because of the rapid decrease of the inhibiting force and the limited annealing time. Considering the high energy boundary (HE), coincidence site lattice boundary (CSL) and solid-state wetting (SSW) models for abnormal grain growth, the first one explained the development of the Goss and {110}<227> grains. Another result was that several matrix grain colonies were observed in the interior or at the boundaries of secondary grains after abnormal grain growth. The grains at the periphery of these colonies showed a large fraction of high energy boundaries (20–45° misorientation) with the surrounding secondary grain and similar grain size with the unconsumed matrix grains. Therefore, these colonies were expected to be consumed by prolonging the annealing time and thus the limited annealing time was responsible for their occurrence. A possible explanation for the dominated high energy boundaries instead of low energy boundaries at the periphery of these colonies was proposed. All of these behaviors promoted the understanding of abnormal grain growth.

36 MATERIALS SCIENCE↗

Degradation processes in high-temperature creep of cast cobalt-based superalloys

Highlights: • Creep degradation processes in Nb or Ta strengthened cobalt-based superalloys were investigated. • CoNb superalloy exhibits longer creep life compared to CoTa superalloy. • Creep fracture ductility of CoTa superalloy is higher than CoNb superalloy. • Low fracture ductility of CoNb superalloy resulted from a premature fracture. • Ductile creep fracture in CoTa superalloy is caused by instability of dislocation microstructure. - Abstract: Degradation processes in high-temperature creep of two cast high-chromium cobalt-based superalloys strengthened by niobium and tantalum for use in the glass industry were analysed via various experimental techniques. Constant load creep tests were conducted at 900, 950 and 1000 °C in a tensile stress range from 40 to 80 MPa. It was found that the CoNb superalloy possesses considerably longer creep life compared to the CoTa superalloy under the same loading conditions. Conversely, the creep ductility of the fractured specimens shows the opposite order of the creep life. The creep behaviour of both superalloys obeys the Monkman-Grant formula indicating that the creep deformation mechanism and fracture processes are mutually interlinked. The homogeneously distributed creep damage of the CoNb superalloy is closely connected with primary carbides and is predominantly initiated either as interface decohesion between the carbide/matrix and carbide eutectics/matrix or by breakage of bulk M{sub 23}C{sub 6} carbides. The dominant type of creep damage in the CoTa superalloy is localized breakage of M{sub 23}C{sub 6} carbides in close proximity of the fracture path. The final brittle fracture in the CoNb superalloy occurs via relatively fast propagation of the longest cracks after the ultimate state of damage is reached. Due to premature fracture, the inherent creep ductility of the CoNb matrix is not exhausted. The final ductile transgranular creep fracture of the CoTa superalloy is caused by a local strain-induced instability of the dislocation microstructure leading to a loss of an external section of specimen (necking).

36 MATERIALS SCIENCE↗

Variation improvement of mechanical properties of Mg-9Al-1Zn alloy with melt conditioned high pressure die casting

Highlights: • The variation improvement of mechanical properties of AZ91D was achieved via application of high shear melt conditioning. • The elongation variation of AZ91D with MC-HPDC has a significant reduction from 31.2% for tradition HPDC to 19.7%. • High shear melt conditioning can result in grain refinement of primary α-Mg formed in both shot sleeve and die cavity. - Abstract: Melt conditioning treatment via high shearing on Mg-9Al-1Zn melt was employed to disperse the oxide inclusions, and to harness the well-dispersed particles as the effective heterogeneous nucleation sites for primary α-Mg grains during solidification in high pressure die casting. To reveal the mechanism of property improvement, Prefil pressure filtration cleanliness analyzer, field-emission scanning electron microscopy with energy dispersive X-ray spectroscopy and high-resolution transmission electron microscopy were employed in present study. The experimental results showed that the application of high shearing not only improved elongation, ultimate tensile strength and yield strength simultaneously, but also reduced the variation of the mechanical properties of Mg-9Al-1Zn alloy. The improvement was ascribed to the refinement of the primary α-Mg grains formed in both shot sleeve and die cavity, and to the reduction of porosity as well as refinement of Mg{sub 17}Al{sub 12} phases.

36 MATERIALS SCIENCE↗

On structure and mechanical properties of ultrasonically cast Al-2% Al{sub 2}O{sub 3} nanocomposite

An investigation on the structure of an ultrasonically cast nanocomposite of Al with 2 wt.% nano-sized Al{sub 2}O{sub 3} (average size {approx}10 nm) dispersoids showed that the nanocomposite was consisting of nearly continuous nano-alumina dispersed zones (NDZs) in the vicinity of the grain boundaries encapsulating Al{sub 2}O{sub 3} depleted zones (ADZs). The mechanical properties were investigated by nanoindentation and tensile tests. The nano-sized dispersoids caused a marginal increase in the elastic modulus, and a significant increase in the hardness ({approx}92%), and tensile strength ({approx}48%). Subsequent cold rolling to achieve a reduction ratio of 2 resulted in an appreciable increase in the hardness due to change in morphology of the microstructure. Estimation of the strength on the basis of inter-particle spacing, which was measured by transmission electron microscopy, could not be accounted for on the basis of Orowan mechanism, and therefore, strengthening mechanisms like local climb and/or cross slip might have a role in this room temperature (0.32T{sub M}) deformation process.

36 MATERIALS SCIENCE↗

Reinforcing blade-cast photocatalytic-titania thin film by titanate nanotubes

Highlights: • Suspension-based photocatalysts are inferior to thin-films due to separation issues. • Hydrothermal TiO{sub 2} nanotubes and sol-gel Ti(n-OBu){sub 4} blends were tape casted on glass. • Optimum blend composition yields mechanical stability due to the tubes reinforcing effect. • At optimum gel content the nanotube bundles are smoothed without stabilizers added. • Surface accessibility and mass transfer dominate the photocatalytic dye degradation. - Abstract: Titanate nanotubes/titania gel blends were prepared as composite sol-gel material, deposited on a glass substrate using a doctor blade and calcined in order to create thin films. In order to get an insight in titania nanotubes’ ability to reinforce thin films, drying control chemical agents were not used. The effects of titanate nanotubes to titanium n-butoxide ratio on surface morphology, phase composition, mechanical stability and photocatalytic activity were studied. Characterization of the thin films was carried out by means of optical and scanning electron microscopy, powder X-ray diffraction, synchrotron radiation grazing incidence X-ray diffraction and mechanical stability testing. Photocatalytic properties of the obtained thin films were evaluated on the basis of methylene blue degradation. Moderate blends exhibit favourable microstructural features while the dye degradation rate was greater for films with a greater amount of titanate nanotubes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Process Parameters on Abnormal Grain Growth during Friction Stir Processing of a Cast Al Alloy

The effects of process parameters and friction stir processing (FSP) run configurations on the stability of nugget microstructure at elevated temperatures were evaluated. Cast plates of an Al-7Si- 0.6Mg alloy were friction stir processed using a combination of tool rotation rates and tool traverse speeds. All single pass runs showed some extent of abnormal grain growth (AGG), whereas multi-pass runs were more resistant to AGG. Additionally, higher tool rpm was found to be beneficial for controlling AGG. These effects were analyzed by comparing the result of this work with other published results and AGG models.

36 MATERIALS SCIENCE↗

Impact of microstructural stability on the creep behavior of cast Al–Cu alloys

Creep behavior of three cast Al–Cu alloys at 300 °C was studied by measuring their steady state creep rates as a function of stress. Microalloying additions in two alloys stabilized the θ' (Al 2 Cu) precipitates to 300 °C, which allowed grain boundary-controlled creep deformation to dominate at low stresses in these alloys. In contrast, the instability of the microstructure at 300 °C in a conventional Al–Cu 206 alloy led to the majority of θ' precipitates transform to the θ phase. The 206 alloy displayed diminished resistance to dislocation motion and a dislocation creep mechanism dominated from the lowest stresses. A modified Coble creep model was developed to describe the experimental low-stress creep rates in the alloys with thermally stable precipitate structures. Finally, it is concluded that increasing the thermal stability of precipitates in Al–Cu alloys can provide significant improvement in their creep performance.

36 MATERIALS SCIENCE↗

Hot deformation behavior of an industrially cast large grained low density austenitic steel

Hot compression testing was performed on specimens of an Fe–30Mn–9Al–1Si-0.9C-0.5Mo wt.% low density steel which were extracted from an industrial casting with large grain size (320 ± 50 μm). Grain boundaries act as nucleation sites for dynamic recrystallization in the present material and the large grain size results in fewer nucleation sites, which delays dynamic recrystallization to larger strains and/or higher temperatures and causes higher rates of work hardening relative to similar materials but with smaller grain sizes. Here, a relatively high activation energy for hot deformation of 470 ± 90 kJ mol –1 was determined from a Zener-Hollomon analysis of the flow stresses at different temperatures and strain rates, attributed in part to the large grain size.

36 MATERIALS SCIENCE↗

Effect of Cr and Ni concentrations on resilience of cast Nb- alloyed heat resistant austenitic steels at extreme high temperatures

Austenitic Cr–Ni alloyed heat resistant steels with Nb additions are used for intensively thermo-mechanically loaded cast components working in extreme high temperature oxidizing environment. Their performance during static oxidation and transient thermo-mechanical loading was investigated to recommend an optimal cost-effective Cr/Ni composition of Nb-alloyed austenitic class steels. Here, the static oxidation and transient thermo-mechanical behavior of three austenitic steels with different Cr/Ni alloying levels were investigated and compared for variety of working conditions. Static oxidation was performed between 900 °C and 1000 °C in air for 400 h. The critical temperature which increases spallation during static oxidation was determined for each of the steel alloying levels. In addition, thermal cycling of a constrained specimen was done with varying upper cycling temperatures between 850 °C and 1000 °C. SEM and TEM analyses were supported by thermodynamic simulation of the phases precipitated in the metal matrix and the structure of formed oxide layers. These studies were used to determine the mechanisms of degradation of thermo-mechanically loaded Cr/Ni austenitic steels at extreme high temperatures. A recommendation for a cost-effective Cr/Ni alloying level for different working conditions was determined.

36 MATERIALS SCIENCE↗

Molecular packing control enables excellent performance and mechanical property of blade-cast all-polymer solar cells

All-polymer solar cells (all-PSCs) are the most promising power generators for flexible and portable devices due to excellent morphology stability and outstanding mechanical property. Prior work suggests high crystallinity is beneficial to device performance but detrimental to mechanical property, therefore identifying the optimized ratio between crystalline and amorphous domains becomes important. In this work, we demonstrated highly efficient and mechanically robust all-PSCs by blade-coating technology in ambient environment based on PTzBI:N2200 system. By controlling the aggregation in solution state and ultrafast film formation process, a weakly ordered molecular packing morphology as well as small phase separation is obtained, which leads to not only the good photovoltaic performance (8.36%-one of the best blade-cast device in air) but also prominent mechanical characteristic. The controlled film reflects a remarkable elongation with the crack onset strain of 15.6%, which is the highest result in organic solar cells without adding elastomers. These observations indicate the great promise of the developed all-PSCs for practical applications toward large-area processing technology.

42 ENGINEERING↗

Effects of Block Length and Solution-Casting Conditions on the Final Morphology and Properties of Disulfonated Poly(arylene ether sulfone) Multiblock Copolymer Films for Proton Exchange Membranes

The effects of block length and solution-casting conditions on the final microstructures and properties of disulfonated poly(arylene ether sulfone) multiblock copolymer (BPSH100-BPS0) films for proton exchange membranes were investigated based on the basic principles of microstructure formation of block copolymers. Morphological studies using transmission electron microscopy and small angle X-ray scattering demonstrated that as the block length increased, the inter-ionic-domain distance increased, with a subsequent increase in lamellar ordering and long-range continuity. Further enhancement in morphological order was achieved by simply utilizing a selective solvent, dimethylacetamide, which is good and marginal for the sulfonated and unsulfonated blocks, respectively, rather than a neutral solvent, N-metyl-2-pyrrolidone. These morphological enhancements led to higher proton conductivity and water uptake. Drying temperature and/or solvent removal rate were observed to have considerable effects on water uptake and swelling behavior, being coupled with solvent selectivity. Also, the multiblock copolymer consisting of longer blocks was found to be more sensitive to the variation of the processing conditions such as solvent type and film drying temperature.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Probing the fatigue enhancement in a thermally aged cast duplex stainless steel by in situ neutron diffraction

After long-term thermal aging at 400 °C for 3000 h and 10,000 h, a cast duplex stainless steel exhibits promoted fatigue performance, including enhanced three-stage cyclic hardening and prolonged fatigue life. Utilizing in situ neutron diffraction, the phase-specific stresses are resolved, and their evolutions over entire fatigue cycling reveal the underlying mechanisms of the fatigue enhancement. It is found that the ferrite phase bears a much higher stress than the austenite matrix under both as-received and aged conditions. The enhanced cyclic hardening in Stage I is attributed to the strengthening of both phases due to thermal aging, while the enhancement in Stage III results from the martensitic transformation induced strengthening. The fatigue life is prolonged thanks to the cyclic hardening and the delay of martensitic transformation in the austenite phase after thermal aging.

Yu, Dunji↗

Characterization of Continuous Cast AA2037 Al Alloy

The microstructure of a contiuous cast Al alloy was characterized with transmission and scanning transmission electron microscopy, as well as x-ray microanalysis. Several precipitate phases were identified as a function of prior thermomechanical treatment in order to understand the improvement of fatigue properties resulting from those treatments.

36 MATERIALS SCIENCE↗

Detecting Thermally Induced Spinodal Decomposition with Picosecond Ultrasonics in Cast Austenitic Stainless Steels

Given the existential climate crisis faced by mankind and the world, the lifetime and sustainability of nuclear reactors as a carbon-free source of renewable energy depend on the susceptibility of their structural components to environmental degradation. In particular, critical components for light water reactors (LWRs) evolve over decades in service, losing ductility and toughness due to thermal and irradiation aging. Techniques to monitor their health cannot be easily applied in the field due to their destructive, expensive, or immobile nature. Thus, non-destructive evaluation (NDE) methods are sought to monitor and evaluate the health of major LWR components such as core barrels, steam generator tubes, or primary coolant pipes and are often required by policy, such as NRC policy #10-CFR-50.65. In this work we demonstrate the use of gigahertz, non-contact ultrasonics to gauge the state of cast austenitic stainless steels (CASS), used in some of the largest components in LWR primary systems. We do so by linking changes in their surface acoustic wave (SAW) characteristics using transient grating spectroscopy (TGS) to transmission electron microscopy (TEM)-verified evidence of spinodal decomposition and G-phase precipitation. In this thesis, thermal aging is shown to induce SAW peak splitting in spinodally decomposed CASS alloys, correlated strongly with lowered toughness and decreased ductility. Furthermore, statistical testing on the number of SAW peak splits observed show that the second SAW peak significantly appears more frequently and is significantly different in frequency in comparison to counts and frequencies measured in unaged specimens. The ability of this technique to non-destructively detect microstructural degradation at a distance in a predictive manner in the case of CASS motivates extending gigahertz ultrasonics to detect other LWR material degradation modes as an in-vessel inspection technique, such as reactor pressure vessel (RPV) embrittlement. This allows for the greater use of NDE techniques for confident monitoring of LWR structural material health to 80 years and beyond, saving costs by minimizing structural replacements until needed and maximizing energy production by preventing early decommission until necessary.

36 MATERIALS SCIENCE↗

Strong tough hydrogels via the synergy of freeze-casting and salting out

Natural load-bearing materials like tendons possess high water content of ~70% but14 are still strong and tough even when used for over 1 million cycles per year, which is owed to the hierarchical assembly of anisotropic structures across multi-length-scales . In imitation of natural systems, various hydrogels have been created via methods like electro-spinning, extrusion, compositing, freeze casting, self-assembly, and mechanical stretching for improved mechanical performance. However, in contrast to tendons, many hydrogels with the same high water content do not show high strength, large toughness or high fatigue resistance. In this work, we present a strategy to produce strong, tough and fatigue resistant hydrogels with multi-length-scale hierarchical architecture using a freezing-assisted salting-out treatment. The produced exemplary poly(vinyl alcohol) hydrogels are highly anisotropic, comprising micrometer-scale honeycomb-like pore walls, which in turn comprise interconnected nanofibrils meshes, entirely physically assembled from polymer chains. These hydrogels are made of 70-95% water but can exhibit ultra-high ultimate stress (23.5 ± 2.7 MPa) and strain (2900 ± 450%), giant 32226 toughness (210 ± 13 MJ/m , 175 ± 8 kJ/m) and remarkable fatigue threshold (10.5 ± 1.3 kJ/m), which are 10 times tougher than natural tendon. The presented strategy could expand the applicability of weak polymeric material, like hydrogels, in practical applications that requires long-term services with high-loads and abrupt-impacts and extend the development of structural hydrogels.

36 MATERIALS SCIENCE↗

The Effect of Li Additions on Wear Properties of Al-Mg{sub 2}Si Cast In-situ Composites

Wear rate of a modified Al-Mg{sub 2}Si composite was studied by the use of a conventional pin-on-disc technique. In-situ Al-Mg{sub 2}Si composites (15, 20, 25 wt.%) were cast in a simple cylindrical mold. 0.3 wt.% Li was added into the molten composite to modify its microstructure. It has been found that Li addition decreases the mean size of primary Mg{sub 2}Si particles. The wear behavior of different composites at different rates revealed that Li addition increases the wear properties of Al-15%Mg{sub 2}Si to some extent but it did not have any significant influence on wear properties of two other composites.

36 MATERIALS SCIENCE↗