Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Maximizing the Performance of a 3D Printed Heat Sink by Accounting for Anisotropic Thermal Conductivity During Filament Deposition

Newly developed high thermal conductivity polymer composite 3D printing filaments are used to characterize the thermal properties as a function of print orientation. The thermal conductivity of a printed part is anisotropic and varies by 2-6 times depending on the print direction - demonstrating higher conductivity in the deposition direction (in-plane) than in the two directions perpendicular to the deposition direction (cross-plane and through-plane). Therefore, deposition path planning greatly affects the overall heat dissipation rate and the performance of the heat sink. Traditionally, 3D printing slicers generate deposition paths based solely on geometric constraints. This work investigates a new approach of deposition path planning assisted by computational predictions of the heat sink thermal performance. The proposed approach uses a thermal simulation of a 3D-printed part, accounting for the anisotropic thermal properties, and the orientation of the local material properties are assigned based on the deposition path in multiple print orientations. The performances predicted via the simulations are compared, and the optimal deposition path is determined. For the highest thermal conductivity 3D printing filament (~ 12 W/m- K in-plane), a heat sink printed with the print direction parallel to the fins z-axis had ~20% improved performance in comparison to a heat sink with print direction perpendicular to the fins z-axis. Moreover, a plastic 3D printed heat sink was able to perform within 7% of an extruded Aluminum heat sink with similar geometry under natural convection. The computational predictions show the same trend as experimental measurements using 3D printed heat sinks.

Smith, Matthew↗

Polymers for hydrogen infrastructure and vehicle fuel systems :

This document addresses polymer materials for use in hydrogen service. Section 1 summarizes the applications of polymers in hydrogen infrastructure and vehicle fuel systems and identifies polymers used in these applications. Section 2 reviews the properties of polymer materials exposed to hydrogen and/or high-pressure environments, using information obtained from published, peer-reviewed literature. The effect of high pressure on physical and mechanical properties of polymers is emphasized in this section along with a summary of hydrogen transport through polymers. Section 3 identifies areas in which fuller characterization is needed in order to assess material suitability for hydrogen service.

Barth, Rachel Reina↗

Compression Analysis of Materials via in situ X-ray Computed Tomography

X-ray computed tomography (X-ray CT) is an analytical technique used in materials science to non– destructively characterize features in a variety of materials like polymers, metals, composites, and explosives. The non-destructive imaging allows for the analysis of features (voids and cracks), which give a fundamental understanding of material characteristics.This is more effective when combinedwith a load cell to expose the material to realworld stimuli to understand material characteristics and morphological behavior in situ. This study focused on using in situ X-ray CT to understand the material characteristics and morphological changes of sugar prills and a lattice under a compressive load. Sugar prills are used as a surrogate to analyze explosives in a safer and less expensiveway. The sugar prills were found to be brittle and shattered when compressed via the CT renderings and the stress/strain information. The lattices are used as both the basis and ground truth comparison for the development of models to predict the morphological and material characteristic changes that occur as a result of loading. The lattice was found to have weak regions due to low polymer interlayer fusion in these regions during the printing process. It was also found that under the initial compression the lattice demonstrated elastic behavior as its cellular structure was intact until the cellular structure started to collapse causing yielding in the lattice. Additionally, the analysis of the sugar prills and lattice demonstrate the information that can be gleaned from in situ X-ray CT experiments that would be lost in traditional pre- and post-mortem X-rayCT analysis.

36 MATERIALS SCIENCE↗

High Performance Ionene Architectures for Membrane Separations (Final Technical Report)

Our DOE BES research grant (DE-SC0018181, 8/15/17-2/28/22) focused on the synthesis, characterization, and performance of a new class of polymers known as high-performance (HP)-ionenes as gas separation membranes, including associated computational studies. This research resulted in 11 peer-reviewed journal publications with an additional ~7 manuscripts currently in review or under preparation for submission. This DOE BES funding has also resulted in 3 U.S. patent applications.

36 MATERIALS SCIENCE↗

Data-Driven Tailoring Optimization of Thermoset Polymers Using Ultrasonics and Machine Learning

Thermoset polymers are highly demanded for their structural robustness, thermal stability, and chemical resistance. Tailoring the properties of these polymers for high-performance applications is often preferred to designing brand-new polymers. However, the traditional destructive techniques used to characterize their properties as a function of manufacturing parameters are expensive and time-consuming. A novel non-destructive, data-driven method leveraging ultrasonics and machine learning techniques to tailor the properties of thermosets as a function of the manufacturing parameters is demonstrated. Thermoset epoxy samples with varying curing temperatures (15–40 °C) and curing agent amounts (±40%) were manufactured and tested. Their curing kinetics were monitored by determining the sound speed in the material in real time, while the longitudinal modulus of the samples was determined post-cure. Machine learning models were developed using a k-nearest neighbors algorithm. These models were implemented to predict the curing and final elastic properties using the manufacturing parameters, i.e., stoichiometry and curing temperature, and vice versa. Understanding and modeling how these parameters affect the cure kinetics and final properties will allow for efficient and reliable optimization of thermoset tailoring and manufacturing.

36 MATERIALS SCIENCE↗

Evaluation of high temperature polymers

The purpose of this paper is to identify and develop arc-track resistant insulation materials that can operate reliably at 300 C. In the first phase, high performance polymers are evaluated based on structure, thermal stability and electrical properties. Next, the polymers are ranked according to performance and experimental characterization. Then, experimental evaluations in wire configuration are conducted. And selection is made based on performance and commerical potential.

Jayaraj, K.↗

Smart Materials and Structures Applications at the NASA Langley Research Center

This overview of the presentation covers Langley's smart materials infrastructure, materials research, applications, and summary. Langley's infrastructure consists of fabrication and characterization of smart structures. Materials researched include ceramics, polymers, and polymer-ceramic composites. Applications include interior aircraft noise suppression, aircraft engine noise reduction, active flutter damping of aircraft wings for better performance, active shape control of polymeric reflectors, and aircraft wing distortion to eliminate control surfaces.

Horner, Garnett↗

MISSE PEACE Polymers Atomic Oxygen Erosion Results

Forty-one different polymer samples, collectively called the Polymer Erosion and Contamination Experiment (PEACE) Polymers, have been exposed to the low Earth orbit (LEO) environment on the exterior of the International Space Station (ISS) for nearly 4 years as part of Materials International Space Station Experiment 2 (MISSE 2). The objective of the PEACE Polymers experiment was to determine the atomic oxygen erosion yield of a wide variety of polymeric materials after long term exposure to the space environment. The polymers range from those commonly used for spacecraft applications, such as Teflon (DuPont) FEP, to more recently developed polymers, such as high temperature polyimide PMR (polymerization of monomer reactants). Additional polymers were included to explore erosion yield dependence upon chemical composition. The MISSE PEACE Polymers experiment was flown in MISSE Passive Experiment Carrier 2 (PEC 2), tray 1, on the exterior of the ISS Quest Airlock and was exposed to atomic oxygen along with solar and charged particle radiation. MISSE 2 was successfully retrieved during a space walk on July 30, 2005, during Discovery s STS-114 Return to Flight mission. Details on the specific polymers flown, flight sample fabrication, pre-flight and post-flight characterization techniques, and atomic oxygen fluence calculations are discussed along with a summary of the atomic oxygen erosion yield results. The MISSE 2 PEACE Polymers experiment is unique because it has the widest variety of polymers flown in LEO for a long duration and provides extremely valuable erosion yield data for spacecraft design purposes.

deGroh, Kim, K.↗

The Compressive Behavior of Isocyanate-crosslinked Silica Aerogel at High Strain Rates

Aerogels are low-density, highly nano-porous materials. Their engineering applications are limited due to their brittleness and hydrophilicity. Recently, a strong lightweight crosslinked silica aerogel has been developed by encapsulating the skeletal framework of amine-modified silica aerogels with polyureas derived by isocyanate. The mesoporous structure of the underlying silica framework is preserved through conformal polymer coating, and the thermal conductivity remains low. Characterization has been conducted on the thermal, physical properties and the mechanical properties under quasi-static loading conditions. In this paper, we present results on the dynamic compressive behavior of the crosslinked silica aerogel (CSA) using a split Hopkinson pressure bar (SHPB). A new tubing pulse shaper was employed to help reach the dynamic stress equilibrium and constant strain rate. The stress-strain relationship was determined at high strain rates within 114-4386/s. The effects of strain rate, density, specimen thickness and water absorption on the dynamic behavior of the CSA were investigated through a series of dynamic experiments. The Young's moduli (or 0.2% offset compressive yield strengths) at a strain rate approx.350/s were determined as 10.96/2.08, 159.5/6.75, 192.2/7.68, 304.6/11.46, 407.0/20.91 and 640.5/30.47 MPa for CSA with densities 0.205, 0.454, 0.492, 0.551,0.628 and 0.731 g/cu cm, respectively. The deformation and failure behaviors of a native silica aerogel with density (0.472 g/cu cm ), approximately the same as a typical CSA sample were observed with a high speed digital camera. Digital image correlation technique was used to determine the surface strains through a series of images acquired using high speed photography. The relative uniform axial deformation indicated that localized compaction did not occur at a compressive strain level of approx.17%, suggesting most likely failure mechanism at high strain rate to be different from that under quasi-static loading condition. The Poisson s ratio was determined to be 0.162 in nonlinear regime under high strain rates. CSA samples failed generally by splitting, but were much more ductile than native silica aerogels.

Luo, H.↗

Chlorine Validation through Critical Integral Experiments

An increased interest in the validation of chlorine nuclear data, specifically 35Cl, in recent years has led to the prioritization of conducting chlorine critical experiments for nuclear data validation and criticality safety evaluations. A previous experiment was conducted with PVC and CPVC (chlorinated polyvinyl chloride) to reduce the margin of subcriticality for PF-4 operations with aqueous plutonium chloride solutions. Challenges in determining the composition of specific polymers, namely the CPVC, made it difficult to characterize, and therefore benchmark. Additional materials that were utilizable for chlorine validation were not immediately clear, as form, strength, purity, and composition are all important. A series of possible absorber materials were identified and studied, but ultimately granular sodium chloride was chosen. In addition to the needs of LANL’s PF-4 other industry collaborators have brought attention to the need for chlorine validation. Specifically, the need for HEU electrorefining with LiCl salts at Y-12 was taken into consideration for this experiment, with the experimental configurations being finely tuned to best meet their needs. Needs for validation were also presented by Idaho National Lab (INL) and TerraPower for validation of their Molten Chloride Reactor Experiment (MCRE) and Molten Chloride Fast Reactor (MCFR) and have also been considered.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Heterogeneous chain dynamics and aggregate lifetimes in precise acid-containing polyethylenes: Experiments and simulations

Melt state dynamics for a series of strictly linear polyethylenes with precisely spaced associating functional groups were investigated. The periodic pendant acrylic acid groups form hydrogen-bonded acid aggregates within the polyethylene (PE) matrix. The dynamics of these nanoscale heterogeneous morphologies were investigated from picosecond to nanosecond timescales by both quasi-elastic neutron scattering (QENS) measurements and fully atomistic molecular dynamics (MD) simulations. Two dynamic processes were observed. The faster dynamic processes which occur at the picosecond timescales are compositionally insensitive and indicative of spatially restricted local motions. The slower dynamic processes are highly composition dependent and indicate the structural relaxation of the polymer backbone. Higher acid contents, or shorter PE spacers between pendant acid groups, slow the structural relaxation timescale and increase the stretching parameter (β) of the structural relaxation. Additionally, the dynamics of specific hydrogen atom positions along the backbone correlate structural heterogeneity imposed by the associating acid groups with a mobility gradient along the polymer backbone. At time intervals (<2 ns), the mean-squared displacements for the four methylene groups closest to the acid groups are up to 10 times smaller than those of methylene groups further from the acid groups. At longer timescales acid aggregates rearrange and the chain dynamics of the slow, near-aggregate regions and the faster bridge regions converge, implying a characteristic timescale for the passage of chains between aggregates. As a result, the characterization of the nanoscale chain dynamics in these associating polymer systems both provides validation of simulation force fields and provides understanding of heterogeneous chain dynamics in associating polymers.

36 MATERIALS SCIENCE↗

Synthesis and electrical analysis of nano-crystalline barium titanate nanocomposites for use in high-energy density applications.

Ceramic based nanocomposites have recently demonstrated the ability to provide enhanced permittivity, increased dielectric breakdown strength, and reduced electromechanical strain making them potential materials systems for high energy density applications. A systematic characterization and optimization of barium titanate and PLZT based nanoparticle composites employing a glass or polymer matrix to yield a high energy density component will be presented. This work will present the systematic characterization and optimization of barium titanate and lead lanthanum zirconate titanate nanoparticle based ceramics. The nanoparticles have been synthesized using solution and pH-based synthesis processing routes and employed to fabricate polycrystalline ceramic and nanocomposite based components. The dielectric/ferroelectric properties of these various components have been gauged by impedance analysis and electromechanical response and will be discussed.

36 MATERIALS SCIENCE↗

Influence of strain-rate on the response of elastomeric architected materials

Architected materials have shown substantial promise in impact mitigation and protective applications, and there has accordingly been great interest in better characterizing their response at elevated strain rates due to impact. There remains ambiguity regarding the contribution of inertial and material responses to strain rate sensitivity, and, in particular, when these effects begin to gain dominance in the impact response of an architected material. The response of soft polymer architected materials as a function of strain rate, in particular, has been little investigated. We characterize the experimental impact response of four soft polymer architected lattice geometries across varying strain rates in the intermediate strain rate regime (∼10 3 s −1 ) using split-Hopkinson pressure bar loading and high speed video characterization of the resulting deformation fields. In conclusion, our results highlight the interplay of influence between constituent material, lattice geometry, length scale, and strain rate in determining the onset of significant inertia effects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Combinatorial Membrane Synthesis: Fundamentals of Hybrid Metal-Organic Brush (MOB) Membranes for Organic Solvent Nanofiltration (Renewal)

(a) Goals: The goals of our current 3-year research project are (i) expansion of the novel modification technique Single Electron Transfer- Living Radical Polymerization (SET-LRP) to graft polymer brushes on a polyimide stable support followed by characterization and testing of the ensuing membrane (ii) stiffen brush network utilizing (a) metal organic frameworks and (b) covalent bonds formed as a result of crosslinking the grafted brush network. (b) Approach: The approach taken for this research was: (i) to graft branches terminated with a carboxyl group on each bristle (or bristle branch) allowing (a) metal immobilization to form MOF-like structures between branches or (b) crosslink bristles using aliphatic or aromatic diamines; (ii) to test the performance of the membranes using organic dyes, pure solvents (alcohols) and industrially relevant organic solvent separations; and (iii) to characterize these modified brush membranes. (c) Findings: The significant findings from the past one year are summarized below (papers resulting from this work are listed below and in D. PUBLICATIONS and relevant references are found in E. REFERENCES.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization and engineering of a two-enzyme system for plastics depolymerization

Significance Deconstruction of recalcitrant polymers, such as cellulose or chitin, is accomplished in nature by synergistic enzyme cocktails that evolved over millions of years. In these systems, soluble dimeric or oligomeric intermediates are typically released via interfacial biocatalysis, and additional enzymes often process the soluble intermediates into monomers for microbial uptake. The recent discovery of a two-enzyme system for polyethylene terephthalate (PET) deconstruction, which employs one enzyme to convert the polymer into soluble intermediates and another enzyme to produce the constituent PET monomers (MHETase), suggests that nature may be evolving similar deconstruction strategies for synthetic plastics. This study on the characterization of the MHETase enzyme and synergy of the two-enzyme PET depolymerization system may inform enzyme cocktail-based strategies for plastics upcycling.

59 BASIC BIOLOGICAL SCIENCES↗

Integrating Emerging Polymer Chemistries for the Advancement of Recyclable, Biodegradable, and Biocompatible Electronics

Abstract Through advances in molecular design, understanding of processing parameters, and development of non‐traditional device fabrication techniques, the field of wearable and implantable skin‐inspired devices is rapidly growing interest in the consumer market. Like previous technological advances, economic growth and efficiency is anticipated, as these devices will enable an augmented level of interaction between humans and the environment. However, the parallel growing electronic waste that is yet to be addressed has already left an adverse impact on the environment and human health. Looking forward, it is imperative to develop both human‐ and environmentally‐friendly electronics, which are contingent on emerging recyclable, biodegradable, and biocompatible polymer technologies. This review provides definitions for recyclable, biodegradable, and biocompatible polymers based on reported literature, an overview of the analytical techniques used to characterize mechanical and chemical property changes, and standard policies for real‐life applications. Then, various strategies in designing the next‐generation of polymers to be recyclable, biodegradable, or biocompatible with enhanced functionalities relative to traditional or commercial polymers are discussed. Finally, electronics that exhibit an element of recyclability, biodegradability, or biocompatibility with new molecular design are highlighted with the anticipation of integrating emerging polymer chemistries into future electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗