Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Airframes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Comprehensive Analysis Aeroelastic Stability Predictions for the Mars Sample Recovery Helicopters and Ingenuity

A rotorcraft comprehensive analysis was used to generate aeroelastic stability predictions for both Ingenuity and the Mars Sample Recovery Helicopters. The analysis was performed multiple times for each rotor system with sequential increases to the level of modeling complexity. Initial cases used an independent blade analysis, trim inflow distribution, no airframe degrees of freedom, and a hover condition (a time-invariant problem). The final model used all blades, dynamic inflow, airframe degrees of freedom, and a Floquet theory approach to the flutter analysis. The approach of sequentially increasing modeling complexity was employed to ensure the causes of any observed instabilities could be identified. For each case, stability results were determined across a range of air densities, tip Mach numbers, and rotor collective pitch settings. For the Sample Recovery Helicopter, a forward flight condition analysis with the highest level of modeling complexity was also performed. The aeroelastic stability predictions showed both the Ingenuity and Sample Recovery Helicopter rotor systems to be stable for all analyzed conditions. Parameter excursions of structural properties were performed to explore conditions resulting in aeroelastic instabilities.

Aeroelastic↗

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗

Experimental Investigation of a Boundary Layer Ingesting Tailcone Thruster Configuration at the National Transonic Facility

A transonic, high Reynolds number wind tunnel test of a Boundary Layer Ingesting Tailcone System (BLITS) was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center during the spring of 2023. The test was sponsored by the NASA Advanced Air Transport Technology Project and produced a large dataset to help in the development and validation of an integrated airframe-turbomachinery computational simulation capability. The Common Research Model with Tail Cone Thruster (CRM-TCT) configuration was tested at Mach numbers from 0.75 to 0.85 and Reynolds number based on mean aerodynamic chord from 5 to 15 million, with the objective of characterizing the tailcone nacelle inlet pressure and flow angle profile, characterizing the aftbody boundary layer (BL), and evaluating the overall airframe configuration performance. The test article included multiple tailcone nacelle assemblies with different measurement objectives, and each assembly was able to be controlled remotely and rotate in small increments, allowing for an increased measurement density for characterizing the nacelle inlet distortion. Additionally, the use of cryogenic-rated miniature BL rakes was successful in measuring boundary layer heights on the aftbody. Sensitivities of the measured quantities of interest to Mach number, Reynolds number, angle of attack, and nacelle weight flow rate are also presented.

boundary layer ingestion (BLI)↗

Thermal Inspection for the Assessment of Adhesively Bonded Metal Adherends

Certification of adhesively bonded structures is currently a challenge for aircraft manufacturers. The ability to certify bonds in primary structure can reduce dependence on fasteners and this will enable more efficient manufacturing. For example, drilling holes and installing fasteners in bonded joints can be a potentially significant bottleneck in airframe manufacturing. In addition, fasteners increase the airframe weight and can add stress concentration areas. Reducing fastener count can accelerate manufacturing and improve aircraft performance. NASA is currently investigating nondestructive evaluation (NDE) techniques to assess bond integrity. For example, bond thickness influences bond strength and therefore NDE techniques are being investigated to determine bond thickness. For bonded metal structures, there is a large difference in the thermal diffusivity between the 7075 aluminum alloy metal adherends and aircraft grade adhesive. Multi-layered thermal models show a large variation in the thermal response for bondline adhesive thicknesses that vary from 100 to 300 microns for adherend thicknesses of 0.163 cm. Experimental through-transmission thermal measurements reveal promise to quantitatively characterize the bondline thickness. Results were validated with X-ray computed tomography and optical microscopy measurements, and influence of porosity on the thermal model and measurements are investigated.

X-ray computed tomography↗

Thermal Inspection for the Assessment of Adhesively Bonded Metal Adherents

Certification of adhesively bonded structures is currently a challenge for aircraft manufacturers. The ability to certify bonds in primary structure can reduce dependence on fasteners and this will enable more efficient manufacturing. For example, drilling holes and installing fasteners in bonded joints can be a potentially significant bottleneck in airframe manufacturing. In addition, fasteners increase the airframe weight and can add stress concentration areas. Reducing fastener count can accelerate manufacturing and improve aircraft performance. NASA is currently investigating nondestructive evaluation (NDE) techniques to assess bond integrity. For example, bond thickness influences bond strength and therefore NDE techniques are being investigated to determine bond thickness. For bonded metal structures, there is a large difference in the thermal diffusivity between the 7075 aluminum alloy metal adherends and aircraft grade adhesive. Multi-layered thermal models show a large variation in the thermal response for bondline adhesive thicknesses that vary from 100 to 300 microns for adherend thicknesses of 0.163 cm. Experimental through-transmission thermal measurements reveal promise to quantitatively characterize the bondline thickness. Results were validated with X-ray computed tomography and optical microscopy measurements, and influence of porosity on the thermal model and measurements are investigated.

bondline thickness↗

Materials and structures for hypersonic vehicles

The development of low-density materials with higher strength and stiffness, and more efficient engine and airframe structures is considered enabling technology for reusable hypersonic vehicles. Advanced structural concepts are required for minimum weight hot structures that will be fully reusable. Key design drivers are maximum heating rate, duration of heating, total heat load, flight envelope and type of propulsion system, mission life requirements, and containment of liquid hydrogen. For hot-structures applications in the range from 600-1800°F, advanced alloys of titanium, titanium and nickel aluminides, and metal-matrix composites are leading candidates because of their high specific properties. For temperatures in excess of 2000°F carbon-carbon and ceramic-matrix composites are the most structurally efficient materials. This paper addresses the technology issues for light weight hot structures, gives brief assessments of the state of the art, presents selected highlights of current research, and identifies areas requiring additional development.

Hypersonic Vehicles↗

Materials and structures for hypersonic vehicles

The development of low-density materials with higher strength and stiffness, and more efficient engine and airframe structures is considered enabling technology for reusable hypersonic vehicles. Advanced structural concepts are required for minimum weight hot structures that will be fully reusable. Key design drivers are maximum heating rate, duration of heating, total heat load, flight envelope and type of propulsion system, mission life requirements, and containment of liquid hydrogen. For hot-structures applications in the range from 600-1800°F, advanced alloys of titanium, titanium and nickel aluminides, and metal-matrix composites are leading candidates because of their high specific properties. For temperatures in excess of 2000°F carbon-carbon and ceramic-matrix composites are the most structurally efficient materials. This paper addresses the technology issues for light weight hot structures, gives brief assessments of the state of the art, presents selected highlights of current research, and identifies areas requiring additional development.

Hypersonic Vehicles↗

Aeroacoustics of Flight Vehicles: Theory and Practice. Volume 1: Noise Sources

Methodology recommended to evaluate aeroacoustic related problems is provided, and approaches to their solutions are suggested without extensive tables, nomographs, and derivations. Orientation is toward flight vehicles and emphasis is on underlying physical concepts. Theoretical, experimental, and applied aspects are covered, including the main formulations and comparisons of theory and experiment. The topics covered include: propeller and propfan noise, rotor noise, turbomachinery noise, jet noise classical theory and experiments, noise from turbulent shear flows, jet noise generated by large-scale coherent motion, airframe noise, propulsive lift noise, combustion and core noise, and sonic booms.

Propeller noise↗

Analysis and Evaluation of Supersonic Underwing Heat Addition

The linearized theory for heat addition under a wing has been developed to optimize wing geometry, heat addition, and angle of attack. The optimum wing has all of the thickness on the underside of the airfoil, with maximum-thickness point well downstream, has a moderate thickness ratio, and operates at an optimum angle of attack. The heat addition is confined between the fore Mach waves from under the trailing surface of the wing. By linearized theory, a wing at optimum angle of attack may have a range efficiency about twice that of a wing at zero angle of attack. More rigorous calculations using the method of characteristics for particular flow models were made for heating under a flat-plate wing and for several wings with thickness, both with heat additions concentrated near the wing. The more rigorous calculations yield in practical cases efficiencies about half those estimated by linear theory. An analysis indicates that distributing the heat addition between the fore waves from the undertrailing portion of the wing is a way of improving the performance, and further calculations appear desirable. A comparison of the conventional ramjet-plus wing with underwing heat addition when the heat addition is concentrated near the wing shows the ramjet to be superior on a range basis up to Mach number of about B. The heat distribution under the wing and the assumed ramjet and airframe performance may have a marked effect on this conclusion. Underwing heat addition can be useful in providing high-altitude maneuver capability at high flight Mach numbers for an airplane powered by conventional ramjets during cruise.

wings↗

Acoustic Shielding for a Model Scale Counter-rotation Open Rotor

The noise shielding benefit of installing an open rotor above a simplified wing or tail is explored experimentally. The test results provide both a benchmark data set for validating shielding prediction tools and an opportunity for a system level evaluation of the noise reduction potential of propulsion noise shielding by an airframe component. A short barrier near the open rotor was found to provide up to 8.5 dB of attenuation at some directivity angles, with tonal sound particularly well shielded. Predictions from two simple shielding theories were found to overestimate the shielding benefit.

Acoustics shielding↗

Inlet Trade Study for a Low-Boom Aircraft Demonstrator

Propulsion integration for low-boom supersonic aircraft requires careful inlet selection, placement, and tailoring to achieve acceptable propulsive and aerodynamic performance, without compromising vehicle sonic boom loudness levels. In this investigation, an inward-turning streamline-traced and axisymmetric spike inlet are designed and independently installed on a conceptual low-boom supersonic demonstrator aircraft. The airframe was pre-shaped to achieve a target ground under-track loudness of 76.4 PLdB at cruise using an adjoint-based design optimization process. Aircraft and inlet performance characteristics were obtained by solution of the steady-state Reynolds-averaged Navier-Stokes equations. Isolated cruise inlet performance including total pressure recovery and distortion were computed and compared against installed inlet performance metrics. Evaluation of vehicle near-field pressure signatures, along with under- and off-track propagated loudness levels is also reported. Results indicate the integrated axisymmetric spike design offers higher inlet pressure recovery, lower fan distortion, and reduced sonic boom. The vehicle with streamline-traced inlet exhibits lower external wave drag, which translates to a higher lift-to-drag ratio and increased range capability.

engine airframe integration↗

Aeroacoustic Study of a Subscale Large Civil Transport (STAR) Model – Part 1: Simulations

Results from a computational aeroacoustic study of the Subsonic Transport Aeroacoustic Research (STAR) model are presented. The model, a 26%-scale semispan Boeing 777-200 aircraft, was an inceptive configuration in a comprehensive simulation campaign to accurately predict the airframe noise of a full-scale, large civil transport during landing. The lengthy process of obtaining a high-fidelity, CFD-ready, vetted, digital representation of the model is described in detail. The simulations were performed with the STAR model installed in the NASA Ames 40- by 80-foot full-scale wind tunnel to enable direct comparisons with aerodynamic and acoustic measurements of the model, presented separately in Part 2 of the study. Two versions of the wind tunnel test section were considered. The entire test section was used to simulate the aerodynamic behavior of the model; an open-wall representation of the section was adopted during the acoustic simulations to eliminate wall reflections. To preserve the aerodynamic equivalency of the model for the two simulated tunnel configurations, the open-wall computations were executed at an angle-of-attack one degree higher than that of the corresponding closed-wall tunnel. The effect on aerodynamic behavior of several minor geometry alterations necessary to con-form the simulated to the tested model was assessed – the modifications considerably altered the strength and extent of a flow separation zone on the inboard segment of the flap. Also evaluated was the impact of spatial resolution on aerodynamic and acoustic characteristics of the model – in general, medium resolution was sufficient to establish convergence trends for averaged surface pressure behavior and proper localization of noise sources. After the aeroacoustic characteristics of the baseline configuration were predicted, a toboggan-shaped fairing designed to reduce main landing gear noise was evaluated computationally. Far-field noise spectra for the baseline and toboggan-equipped STAR model were calculated via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable data surface enclosing the source regions used as input. Results from the simulations indicated that, while the fairing reduced gear noise in the near-field, it had a negligible effect on the far-field noise signature of the model. This trend agreed with previously published experimental results obtained during sub-scale, isolated gear tests and full-scale flight tests

airframe noise↗

Comparison of Boeing 777 Landing Gear Noise Simulations with Flight Test Data

Acoustic phased microphone array measurements of aircraft flyover noise acquired during the 2005 Quiet Technology Demonstrator II test were used to assess the accuracy of high-fidelity, full-scale simulations of landing gear noise produced by a large civilian aircraft. The simulations, conducted with the lattice Boltzmann solver PowerFLOW®, used a highly accurate digital model of a Boeing 777-300ER aircraft with the nose and main landing gear components replicating the full-scale geometries. The simulations were performed for aircraft parameters that matched those recorded during the flyover test conditions. For benchmarking purposes, several aircraft configurations were simulated: a) nose landing gear deployed with main landing gear and wing high-lift devices stowed, b) nose and main landing gear deployed with wing high-lift devices stowed and c) nose and main landing gear with wing high-lift devices deployed. To facilitate direct comparison with measured data, the simulated data sets were used to generate synthetic pressure records at the same array microphone locations as those used during the flight test. Broadly self-consistent beamforming techniques and procedures were used to process the synthetic pressure records and the measured data. Integration of select regions of the beamform maps containing the nose or main landing gear yielded good agreement between predicted and measured integrated far-field spectra for forward directivity angles where airframe noise is more prominent.

airframe noise↗

Multiplanar Synthetic Arrays and Their Application to Full-Scale Landing Gear Noise Source Identification

Identification and quantification of noise sources generated by the landing gears of large civil transports are critical for the development of viable abatement technologies that can be applied locally to affect solely the source regions. Leveraging validated computational data sets obtained from airframe noise simulations of a full-scale B777-300ER aircraft, a frame-work based on multiplanar synthetic arrays was developed to examine landing gear sources. The position of the arrays relative to the aircraft nose or main landing gears, the number of microphones in each array, and their distribution pattern were judiciously selected to provide adequate spatial resolution of the sources in the primary flyover, sideline, and upstream directions while maintaining reasonable signal-to-noise ratio and beamwidth over a wide frequency range. Overall, seven synthetic arrays with 800 microphones each, for a total of 5,600 microphones, were used in the framework. Fully synchronous synthetic pressure records at each microphone location were obtained from the simulated data sets via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable data surface enclosing the source regions used as input. Various applications of synthetic multiplanar arrays to acoustic data analysis are presented; the advantages of the framework in properly resolving and identifying the B777 landing gear sources is demonstrated by comparing three-dimensional source distribution maps with those obtained from a synthetic version of the ground-based microphone array used during flight tests of the same aircraft.

airframe noise↗

Effects of Porous Gap Fillers on 30P30N Leading-Edge SlatNoise. Part I: Surface Pressure and Acoustics

The leading edge slat of a high-lift system is one of the main contributors to airframe noise during approach. In a previous experimental study, we assessed the performance of an impermeable slat gap filler as a passive flow control device to reduce the slat noise associated with a two-dimensional, three-element high-lift airfoil. The present paper, the first of two parts,represents a follow-on investigation to assess the relative efficacy of permeable gap fillers thatallow successively higher amounts of flow to pass through the gap. To evaluate the influence of this passive flow control device on the acoustics generated by the unsteady flow near the slat, experiments are conducted in an anechoic wind tunnel by mounting a gap filler to the slat element of the two-dimensional 30P30N high-lift configuration. Measurements are performed at a single geometric angle of attack (𝛼𝑘=8◦) and three different flow speeds that correspond to Reynolds numbers of𝑅𝑒𝑐=1.2𝑒6,1.5𝑒6, and1.71𝑒6, respectively. Steady surface pressure measurements are used to gauge the influence of the permeable gap filler treatments on the overall lift. The effect of each treatment on the radiated noise is analyzed via acoustic array measurements, followed by delay-and-sum beamforming to locate the slat noise sources and to provide the integrated acoustic spectra. The porous gap fillers are found to eliminate the narrowband peaks in the acoustic spectra and, also, to yield a 10 dB reduction in the broadband noise in comparison with the baseline case with no gap filler. The porous gap filler with thelowest permeability acts similar to the impermeable gap filler examined previously. However, the aerodynamics and noise reduction both degrade with increasing permeability. An accompanying abstract describes the particle image velocimetry measurements of the flowfield within the slat cove and on either side of the permeable gap f

slat noise↗

Effects of Porous Gap Fillers on Leading-Edge Slat Noise of 30P30N. Part II: PIV Measurements

The leading edge slat of a high-lift system is one of the main contributors to the airframe noise during approach conditions. This paper, the second of two parts, continues our previous studies on the slat gap filler as a passive noise control device on the two-dimensional, 30P30N multielement airfoil. Whereas the earlier study was focused on the effects of an impermeable gap filler that completely blocks the flow through the gap, this follow-on assessment is devoted to permeable slat gap fillers that allow limited amounts of flow to pass through the gap. Part I of this two-part abstract described the aerodynamic and acoustic effects of the permeable gap fillers, as inferred from both the measurements of static and unsteady surface pressures and the microphone array data for the radiated noise. To understand the physical mechanism responsible for the noise reduction documented in Part I, as well as for the accompanying aerodynamic penalty due to the porous gap fillers, Particle Image Velocimetry (PIV) is used in this paper to measure the flow details in the slat-cove region of the 30P30N model. A single angle of attack (𝛼 = 5.5◦) and a chord based Reynolds number of 1.71𝑒6 are selected as the test conditions. The PIV results show that the slat flow features are significantly altered with the presence of the porous gap filler, resulting in a more stable slat-cove shear layer and, thus, reduced velocity fluctuations with a successive decrease in the permeability. The porous gap filler with the lowest permeability acts similar to the solid gap filler. However, flow separation is observed on the upper side of the porous interface, which leads to an aerodynamic performance penalty via a reduction in lift on the main wing.

slat noise↗