Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dielectric and magnetic properties of microwave-absorbing FeAl x O y catalysts fabricated via solution combustion synthesis

Iron-based alumina (FeAl x O y ) nanocomposites are microwave-absorbers and catalysts, which makes them promising for emerging microwave-assisted thermocatalytic technologies. Solution combustion synthesis (SCS) has been used to synthesize FeAl x O y powders, and prior work has demonstrated that adjusting SCS parameters significantly changes phase composition and specific surface area of the products. However, it is unclear how synthesis parameters affect their microwave-absorbing properties, which are essential for optimizing microwave-assisted technologies. To address this challenge, in the present work, twelve different FeAl x O y products were synthesized at different combinations of the SCS parameters such as two fuels (citric acid and glycine), two heating modes (hotplate and muffle furnace), and three Fe:Al molar ratios (2:1, 1:1, 1:2). Dielectric and magnetic properties of the products were characterized using a network analyzer and a vibrating sample magnetometer. Based on the measured permittivity and permeability, penetration depth and reflection loss were calculated as a function of frequency and bed thickness. The products were heated by microwaves at 2.45 GHz and then examined with X-ray diffraction (XRD) analysis. For all products, the magnetic saturation was lower than for bulk iron oxides because of the small crystallite size and aluminum substitution. The use of glycine induced high dielectric losses and enabled fast microwave-heating rates compared to citric acid. Higher Fe:Al ratio also led to higher dielectric and magnetic losses. With glycine fuel, SCS in a furnace induced larger penetration depth and lower microwave absorption than SCS on a hotplate. The minimization of reflected power was more sensitive to the thickness of the product bed than to the frequency of the electromagnetic field. Post-heating XRD analysis revealed different phase transformations in the FeAl x O y powders depending on the SCS parameters. As a result, an FeAl x O y material, synthesized via incipient wetness impregnation, lacked magnetic losses and did not heat well as compared to the SCS products.

Combustion synthesis↗
DOE OSTI2022

ExaCA: A performance portable exascale cellular automata application for alloy solidification modeling

Modeling the as-solidified grain structures that form during alloy processing is a critical component in understanding process-property relationships, particularly for additive manufacturing (AM) where grain structure is very sensitive to processing conditions. While cellular automata (CA)-based models have proven able to predict aspects of microstructure for several alloys and AM process conditions, long run times and large resource sets required limit the utility and the problem size to which existing CA models can be applied. As part of the ExaAM project, an initiative within the Exascale Computing Project (ECP) to develop, test, and optimize an exascale-capable coupled and self-consistent model of AM parts, we developed ExaCA (https://github.com/LLNL/ExaCA) for the liquid–solid phase transformation in the wake of AM melt pools. The CA-based code is parallelized using MPI and the Kokkos programming model, the latter enabling simulation on both CPUs and GPUs within a single-source implementation. Here, we detail the steps taken to transform a baseline, MPI-based CA code into one that is performant on CPUs and GPUs. Performance testing of ExaCA on Summit (a pre-exascale machine at Oak Ridge National Laboratory) was used to quantify CPU–GPU speedup comparing with equal numbers of nodes. Testing showed comparable CPU performance to the MPI-only CA code and a 5-20x speedup when running AM-based test problems using GPUs. The improved performance of CA through GPU utilization and the performance portable nature of ExaCA will enable accurate part-scale modeling by harnessing the power of current and future generations of high performance computing resources. Future work will include improving the strong scaling of ExaCA on GPUs by reducing load imbalance associated with the locality of the problem, and continuing performance optimization across exascale hardware.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Oxidation kinetics and microstructure evolution of high Mn stainless-steel alloy in CO 2 at 700 °C

Oxidation kinetics and scale formation were examined in 21–2N Stainless Steel alloys in a CO 2 environment at 700 °C. Several characterization techniques were used to identify the morphology, crystallographic structure, and chemical composition of the oxide scale formation during exposures up to 1925 h. High manganese content played an important role in homogenous oxide scale formation of Mn 3 O 4 and MnCr 2 O 4 at the scale/gas and scale/alloy interfaces and as an FCC stabilizer in the alloy. Depletion of Mn resulted in an FCC to BCC phase transformation at the scale/alloy interface. No carburization was observed, indicating that the oxide layer is preventing carbon uptake.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Optimizing high energy density sulfur cathodes: A multivariate approach to electrode formulation and processing

Lithium-sulfur (Li-S) batteries involve complex solid-liquid-solid phase transformations during both discharging and charging processes, where cathode materials, formulation, and structure play a crucial role. Here, a design of experiments (DoE) methodology and an empirical model are developed to systematically explore the interactions and trade-offs among cathode factors and process variables, and to obtain generalizable effects estimates for the multivariate system. Compared to the conventional one-factor-at-a-time (OFAT) approach, this work demonstrates advantages in both efficiency and accuracy by allowing the data to guide future research and decisions. Further, an optimized cathode formulation and processing parameters are predicted and validated experimentally, achieving over 1000 mAh g -1 in discharge capacity and improved cycling under practical lean electrolyte (4 µL mg -1 S) and high S-loading cathodes (>4 mg cm -2 ) conditions. The optimized cathode was scaled up and assembled into Li-S pouch cells, achieving 316 Wh kg -1 in cell-level energy, proving that the comprehensive and rigorous framework for optimizing complex systems with DoE leads to improved performance in a practical pouch cell system.

25 ENERGY STORAGE↗
DOE OSTI2023

Gas nitriding behavior of refractory metals and implications for multi-principal element alloy design

Multi-principal element alloys (MPEAs) comprise a large, flexible compositional space that enables tuning of their chemistry, structure, and properties. Here, to facilitate the development of nitriding-based surface-enhancement strategies that harness a broad compositional space, this study examined the gas nitriding behavior of Hf, Mo, Nb, Ta, Ti, and Zr as a function of time, temperature (750 and 1000 °C), and nitriding potential (i.e. ammonia-to-hydrogen ratio). These metals were selected because they have a strong driving force to form nitrides, and appear in many promising refractory MPEA compositions. The nitriding temperatures were selected based on the phase transformation temperature of Ti and Zr, and the nitriding potentials were chosen such that all elements are expected to form nitrides. Mass gain measurements indicate that all six elements follow parabolic kinetics. The microstructure observations and quantitative microchemical analysis show formation of dense and well-adhered compound layers for Mo, Nb, and Ta. Thick diffusion zones appear in Hf, Ta, Ti, and Zr, and diffusion coefficients were fit to the composition profiles. Partial delamination of the compound layer occurred for Ti and Zr. Peak hardness values above 30 GPa are obtained in the dense compound layers, and the solute hardening of the underlying alloy is correlated with the nitrogen content. The results provide insight into the dynamics of nitride compound formation relative to interstitial dissolution of nitrogen, and are discussed in the context of MPEA composition and processing design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution and intermetallic formation in Zn-3Mg (wt%) powder mixture processed by high-pressure torsion

Severe plastic deformation (SPD) techniques have been used extensively over the past 40 years for producing strong metals and alloys. High-pressure torsion (HPT) is one of the most promising SPD techniques for achieving high strength through nanoscale grain refinement and phase transformation. In this research, a mixture of pure zinc (Zn) and magnesium (Mg) powders, Zn-3Mg (wt%), was HPT-processed under a pressure of 6 GPa for 1, 5, 10, 20, and 30 turns at room temperature to achieve a high strength biodegradable material. In order to understand the effects of pre-consolidation on the resulting microstructure and hardness, HPT processing was performed on loose powders placed in the die and also on a pre-compacted powder mixture and the resulting HPT disks were characterized by X-ray diffraction, scanning electron microscopy, atom probe tomography, and Vickers microhardness. In both cases, the HPT disk microstructures contained nanoscale grains, and stable and metastable strain-induced intermetallics, but an unusual softening appeared at large shear strains. Grain size, grain morphology, and the formation of different intermetallics were analyzed to explain the unusual hardness distribution, and it was found that an inverse Hall-Petch relationship between hardness and grain size exists. It is suggested that thermally-activated phenomena such as grain boundary sliding contributed to the strain-induced softening of this nano-structured biomaterial due to its low melting point. Finally, the current results are compared with those for HPT-processed cast alloys and hybrids of the same composition.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Chemical preintercalation of magnesium ions into ⍺-MoO 3 structure for improved electrochemical stability in Li-ion cells

Chemical preintercalation of layered materials, used as electrodes in intercalation-based energy storage devices, represents a promising strategy to enhance electrochemical stability and extend cycle life. However, standardized synthesis approaches for the chemical preintercalation of diverse ions into various layered materials are lacking, necessitating the development of specific synthesis routes for each ion and layered phase combination. In this study, we present the first successful demonstration of Mg 2+ ion chemical preintercalation into the interlayer region of α-MoO 3 , revealing its stabilizing effect during cycling in non-aqueous Li-ion cells. Using ethanol during hydrothermal treatment facilitated molybdenum reduction, which was critical for Mg 2+ ion preintercalation. Interestingly, we found that Mg preintercalation was accompanied by the incorporation of water. Mg-preintercalated α-MoO 3 exhibited enhanced charge storage capacity, electrochemical stability, and power capability compared to pristine α-MoO 3 electrodes. This improved performance is attributed to the structural stabilization provided by Mg 2+ pillars, which prevent undesirable phase transformations during repeated Li intercalation/deintercalation, and increased Li + ion diffusion due to the shielding of electrostatic interactions between electrochemically cycled ions and the α-MoO 3 lattice, enabled by structural water. In conclusion, our study offers new insights into developing chemical preintercalation synthesis approaches that can be broadly applied to a wide range of pillaring ions and layered material hosts.

25 ENERGY STORAGE↗
DOE OSTI2026

Process control-enabled mitigation of microstructural and plastic heterogeneities in additively manufactured Grade 91 steel

Synergizing wire arc-directed energy deposition (WA-DED) additive manufacturing (AM) with particle-strengthened creep strength-enhanced ferritic (CSEF) steels enables fabrication and repair of critical power-plant components. Investigations focused on fusion-welded particle-strengthened CSEF steels, such as Grade 91 steel, have linked microstructurally heterogeneous regions—forming due to heat affected zones (HAZ)—with premature failure during elevated temperature service. Fusion-based AM, including WA-DED, likewise generates microstructurally and plastically heterogeneous regions due to spatiotemporally varying thermokinetics during deposition. However, works investigating such microstructural heterogeneities, their implications for mechanical behavior, and strategies to mitigate their formation remain scarce. This work identifies microstructurally and plastically heterogeneous regions within the WA-DED-processed Grade 91 steel. Spatial microhardness variations in the as-fabricated specimen correlate with the variation in the attributes of grain, martensitic microstructure, and precipitates across the fusion zone and HAZ. Digital image correlation-enabled tensile tests performed at 500 °C revealed pronounced deformation localization and a wave-like strain distribution, with wavelength close to the melt pool depth, indicating susceptibility of the as-fabricated components to premature creep failure. Such heterogeneity in microstructural and mechanical behavior was attributed to recurring solid-state phase transformations. Subsequently, an interlayer temperature control strategy was implemented, wherein maintaining interlayer temperature above the martensitic start temperature mitigated the heterogeneous microstructural and plastic response in the as-fabricated condition. Findings open pathways to achieving deformation-localization- and creep-resistant microstructures in WA-DED fabricated particle-strengthened CSEF steel components, reducing reliance on post-welding heat treatments—conventionally required to enhance creep resistance—and enabling on-demand, short lead-time fabrication of next-generation power-plant components.

Heat affected zones↗
DOE OSTI2020

Irradiation effects on Al 0.3 CoCrFeNi and CoCrMnFeNi high-entropy alloys, and 316H stainless steel at 500 °C

To evaluate the potential of high entropy alloys (HEAs) for nuclear applications, two HEAs, Al 0.3 CoCrFeNi and CoCrFeMnNi, and a conventional Type 316H stainless steel (SS) were irradiated with 1 MeV krypton ions at 500 degrees C up to 1 dpa, and examined in-situ with a transmission electron microscope (TEM). After irradiation, a high density of ordered L1 2 nanoparticles was observed in Al 0.3 CoCrFeNi. In contrast, no phase transformation was observed in CoCrFeMnNi and 316H SS. In the thin foil regions of TEM samples, stacking-fault tetrahedra were observed in the HEAs. In the thick foil regions, interstitial dislocation loops were observed for all alloys, and the areal loop density increased linearly with foil thickness. The Al 0.3 CoCrFeNi had the largest loop size (the lowest density), followed by the CoCrFeMnNi and then the 316H SS. The higher loop nucleation rate in the 316H SS was attributed to carbon content. Finally, the degree of irradiation hardening was slightly lower for the HEAs than for the 316H SS, which is a promising sign for the nuclear application of HEAs at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Radiation induced amorphization of carbides in additively manufactured and conventional ferritic-martensitic steels: In-situ experiments on extraction replicas

In-situ irradiations using 1 MeV Kr 2+ ions in a transmission electron microscope were performed on extraction replica samples containing M 23 C 6 carbides and MX carbonitrides from two ferritic-martensitic (FM) steels: (i) 9%Cr-1%W-TaV based Eurofer97 and (ii) 9%Cr-1%Mo-VNb (all in wt.%) based additively manufactured (AM) Grade91 steel. The irradiations were performed between 100 and 773 K up to a maximum dose of ~2.4 displacements per atom (dpa). The M 23 C 6 carbides are highly susceptible to radiation induced amorphization (RIA), while the MX type nanoprecipitates are highly amorphization resistant across the entire irradiation temperature range. Between 100 and 423 K, RIA of M 23 C 6 carbides occurs very rapidly with critical amorphization doses ranging between ~0.35 and 0.9 dpa, increasing to higher doses at 573 K. Complete amorphization of the M 23 C 6 carbides up to doses of ~2.4 dpa is not possible at 773 K under the present irradiation conditions. The critical amorphization dose of M 23 C 6 carbides increases nearly exponentially with irradiation temperature. The critical temperature for the crystalline-to-amorphous phase transformation (T c→a ) of M 23 C 6 carbides irradiated as replica samples, i.e. without the surrounding metal matrix, was estimated to be ~812 K. Comparing the present results with neutron irradiation data on bulk samples reveals a decrease in the critical amorphization dose for M 23 C 6 and an increase of T c→a , highlighting the effect of dose rate on the amorphization behavior that is qualitatively consistent with literature on other non-metals. Changes in the minor chemistry of M 23 C 6 , such as presence or absence of W, V, Nb, Mo, seems to have little effect on the amorphization behavior. Here, in-situ irradiations on extraction replica samples provide a novel pathway to explore radiation tolerance of nanoprecipitates in nuclear structural materials

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-throughput investigation of structural evolution upon solid-state in Cu–Cr–Co combinatorial multilayer thin-film

Cu-Cr-Co combinatorial multilayer thin-films were prepared by a high-throughput ion beam sputtering system. Based on the thickness ratio among the individual nanoscale monolayers (Cu, Cr, Co), the resulting stoichiometry covered the entire phase diagram. The chemical composition and structure of Cu-Cr-Co combinatorial chip upon solid-state reaction were studied by lab-based micro-X-ray fluorescence (mu-XRF) and high-throughput synchrotron X-ray diffraction (XRD), respectively. A composition-structure map for Cu-Cr-Co combinatorial chip was developed through automated data analysis employing hierarchical clustering techniques. The structural evolution of Cu-Cr-Co combinatorial chip as a function of heat-treatment temperature, time, and modulation period were studied systematically. Furthermore, the effect of the elemental distribution in-depth direction was investigated to gain more insights regarding phase transformation. This work provides an efficient method and new perspectives for the design and optimization of the composition and structure of high-performance thin-films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

E-beam-enhanced solid-state mechanical amorphization of α-quartz: Reduced deformation barrier via localized excess electrons as network modifiers

Under hydrostatic pressure, α-quartz (α-SiO 2 ) undergoes solid-state mechanical amorphization wherein the interpenetration of [SiO 4 ] 2- tetrahedra occurs and the material loses crystallinity. This phase transformation requires a high hydrostatic pressure of 14GPa because the repulsive forces resulting from the ionic nature of the Si–O bonds prevent the severe distortion of the atomic configuration. Herein, we experimentally and computationally demonstrate that e-beam irradiation changes the nature of the interatomic bonds in α-quartz and enhances the solid-state mechanical amorphization at nanoscale. Specifically, during in situ uniaxial compression, a larger permanent deformation occurs in α-quartz submicron pillars compressed during e-beam irradiation than in those without e-beam irradiation. Microstructural analysis reveals that the large permanent deformation under e-beam irradiation originates from the enhanced mechanical amorphization of α-quartz and the subsequent viscoplastic deformation of the amorphized region. Further, atomic-scale simulations suggest that the delocalized excess electrons introduced by e-beam irradiation move to highly distorted atomic configurations and alleviate the repulsive force, thus reducing the barrier to the solid-state mechanical amorphization. In conclusion, these findings deepen our understanding of electron–matter interactions and can be extended to new glass forming and processing technologies at nano- and microscale.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The influence of stacking faults on mechanical behavior of advanced materials

We report there are abundant studies on deformation mechanisms in metallic materials dominated by grain boundaries and twin boundaries. In comparison, the influence of stacking faults on deformation mechanisms of materials remains less well understood. Recent studies have shown that when the density of stacking faults increases sharply, their influence on mechanical behavior of metallic or ceramic materials becomes prominent, and in fact, dominates in some cases. This article reviews recent research progress on how nanoscale stacking faults impact the mechanical behavior of metallic and ceramic materials. We primarily focus on studies that reveal the formation of pre-existing stacking faults, their interactions with dislocations, and phase transformations during plastic deformation as evidenced by experiments and simulations. The aim of this review is to highlight the potential opportunities in using stacking faults to tailor the deformation mechanisms of advanced materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and mechanical properties of high Mn-containing ferritic-martensitic alloys exposed to cyclical thermal treatment

Substantial residual tensile stress tends to accumulate in currently available high-Cr ferritic martensitic steels that are subjected to cyclical heat treatment, which leads to premature brittle fracture. By tailoring the alloy composition, this thermal cycling can be exploited to induce a high number density of nanoprecipitates and phase transformations countering residual tensile stresses. In this work, three new variants of ferritic-martensitic steels have been designed with computational thermodynamics to meet the goals of mitigating residual tensile stresses by lowering martensite start temperatures and of enhancing mechanical strength and irradiation sink strength by increasing the number density of nanoprecipitates. Furthermore, ctenast materials were subjected to cyclical heat treatment. The thermally cycled samples were evaluated with mechanical testing and microstructural analysis to identify the optimal composition in which figures of merit include low residual stress and a high density of nanoscale MX (M = metal, X = C/N) precipitates, leading to high yield strength with reasonable ductility. The noticeably higher density of nanoprecipitates in the optimal alloy favor its higher yield strength, which is supported by the microstructure-derived yield strength calculation and precipitation kinetics simulation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects of magnetic field assisted heat treatment on the microstructure and mechanical properties of Fe-0.63 %C alloy

This study investigates the influence of an applied magnetic field on the microstructural evolution and mechanical properties of hypoeutectoid steels subjected to heat treatment. Tensile tests and microstructural analysis were performed on samples processed under varying magnetic field strengths (0 T, 5 T, and 9 T) and different austenitization incubation times. The results indicate that the application of a magnetic field alters the fraction of proeutectoid ferrite phase without changing the cooling rates and heat treatment process. Additionally, pearlite microstructural features such as lamellar spacing and misorientation angles exhibit variations under different field strengths. While the pearlite nodule diameter remains largely unaffected, an increase in percentage elongation and strength is observed in the 5 T treated sample, attributed to changes in microstructural features with the magnetic field. Additionally, the percentage elongation is reduced in the samples heat treated with reduced austenitization incubation times. The study further demonstrates that low-angle misorientations increased in the samples taken parallel to the magnetic field direction, influencing the mechanical response. These findings suggest that applying a magnetic field during heat treatment provides an additional driving force for phase transformations, offering a manufacturing process for tailoring microstructures and optimizing mechanical properties. Moreover, integrating magnetic fields in heat treatment processes has potential benefits in energy efficiency.

High magnetic field↗
DOE OSTI2020

Mechanistic insights into the colloidal assembly of mesoporous silica using in-operando cross-scale X-ray scattering and spectroscopic measurements

Advancing a mechanistic understanding of the colloidal to solid-phase transformations of silica allows us to tune these meso-scale structures. In this study, we probe the structural transformations associated with the formation of mesoporous silica particles, SBA-15 using in-operando Small Angle X-ray Scattering (SAXS) and Grazing Incidence-Small Angle X-ray Scattering (GI-SAXS). The chemical transformations associated with the hydrolysis and condensation of silica particles is investigated using Attenuated Total Reflection – Fourier Transform Infrared Spectroscopy (ATR-FTIR) measurements. Fast polymerization of Si-O-Si species to form mesoporous silica is noted when SBA-15 is synthesized in the presence of nitrate salts, due to the “salting-in” effect or enhanced solubility of polymers. However, aging the silica particles resulted in plate-like morphologies in the absence of the nitrate salt and spherical morphologies in the presence of nitrate salt. Early onset of nucleation of silica particles in the presence of nitrate salts was captured using GI-SAXS measurements. These studies show that the rational basis for developing new synthesis routes for accelerated kinetics or specific meso-scale structures can be informed by detailed characterization of the evolution in chemistry and meso-scale structure of these materials.

36 MATERIALS SCIENCE↗