Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HEAT TREATMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 757 records · Page 42
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Experimental and Computational Studies of Stress Corrosion Cracking of Alloys 308/309 and 82/182 Weldments in Corrosive and Radiation Environment

The goal of the project was to determine factors that influence SCC and IASCC in weldments found in LWR nuclear power plants. We focused on a SA508-304L SS weldment fabricated by EPRI using gas tungsten arc welding and used an aggressive BWR normal water chemistry (NWC) immersion environment. This weldment used 309L butter and 308L groove filler material. The microstructure of the 309L butter was non-uniform, exhibiting a 20–30μm thick martensitic layer closest to the SA508 interface, a 1–4 mm thick single γ austenite phase dilution zone, and a γ–δ duplex region extending to the 308L groove filler. The 308L groove filler had an entirely γ–δ duplex microstructure. Two approximately 1-inch thick 304L and SA508 plates approximately 12 by 6 square inches were joined using standard nuclear grade welding techniques. This included a post weld heat treatment of the 309L butter after application, a 0.32 cm fit-up root opening, and 57 bead lines of 308L groove filler applied in 18 layers. A 60 degree weld bevel angle was used and the 309L butter was 1.5 cm thick. Displacement cascade damage was induced using proton irradiation at the Michigan Ion Beam Laboratory. The incident proton energy was 2 MeV, the sample temperature was 360 ºC, and the calculated dpa value at 10 μm (60% of the Bragg peak depth of ~18 μm) was 5 dpa using the quick Kinchin-Pease model. Proton irradiation to this damage level required approximately 125 hours of beam time. Two types of samples were irradiated, tensile specimens and TEM bars. Samples were selected from all regions of the weldment, including the SA508-309L butter interface, the 309L-308L interface, and 308L-304L interface. The stainless steel alloys (304L, 308L, and 309L) within the heat affected zone are characterized by a duplex skeletal morphology of δ-ferrite and γ-austenite resulting from the recrystallization associated with weld fabrication. Approximately 7 to 8 mm of length along the specimen was irradiated. The gauge volume surfaces were mechanically polished and then electro-polished to remove mechanical damage from the mechanical polishing step prior to irradiation. Immersion tests were performed in a recirculating autoclave under BWR NWC conditions (2000 ppb wt. dissolved oxygen, neutral pH, 288 ºC, 10 MPa, and inlet water conductivity <100 nS/cm) to accelerate corrosion. Constant strain rate tests were performed either to failure or to approximately 5% strain. Strain rates of 10 -7 to 10 -6 mm/mm/s were used and typical immersion testing required four to six weeks to achieve failure or strains near 5%. Analysis primarily used advanced electron microscopy techniques of FIB lift out specimens.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Process control-enabled mitigation of microstructural and plastic heterogeneities in additively manufactured Grade 91 steel

Synergizing wire arc-directed energy deposition (WA-DED) additive manufacturing (AM) with particle-strengthened creep strength-enhanced ferritic (CSEF) steels enables fabrication and repair of critical power-plant components. Investigations focused on fusion-welded particle-strengthened CSEF steels, such as Grade 91 steel, have linked microstructurally heterogeneous regions—forming due to heat affected zones (HAZ)—with premature failure during elevated temperature service. Fusion-based AM, including WA-DED, likewise generates microstructurally and plastically heterogeneous regions due to spatiotemporally varying thermokinetics during deposition. However, works investigating such microstructural heterogeneities, their implications for mechanical behavior, and strategies to mitigate their formation remain scarce. This work identifies microstructurally and plastically heterogeneous regions within the WA-DED-processed Grade 91 steel. Spatial microhardness variations in the as-fabricated specimen correlate with the variation in the attributes of grain, martensitic microstructure, and precipitates across the fusion zone and HAZ. Digital image correlation-enabled tensile tests performed at 500 °C revealed pronounced deformation localization and a wave-like strain distribution, with wavelength close to the melt pool depth, indicating susceptibility of the as-fabricated components to premature creep failure. Such heterogeneity in microstructural and mechanical behavior was attributed to recurring solid-state phase transformations. Subsequently, an interlayer temperature control strategy was implemented, wherein maintaining interlayer temperature above the martensitic start temperature mitigated the heterogeneous microstructural and plastic response in the as-fabricated condition. Findings open pathways to achieving deformation-localization- and creep-resistant microstructures in WA-DED fabricated particle-strengthened CSEF steel components, reducing reliance on post-welding heat treatments—conventionally required to enhance creep resistance—and enabling on-demand, short lead-time fabrication of next-generation power-plant components.

Heat affected zones↗
NASA NTRS2023

Magnetic Anisotropy and Stress Dependent Epoxy Wetting in FeNi-based Metal Amorphous Nanocomposite

Recently developed FeNi-based metal amorphous nanocomposites (MANCs) used in high-speed motors (HSMs) exhibit reduced eddy current losses while maintaining good mechanical properties and glass-forming abilities. Magnetic anisotropy in (Fe 70 Ni 30 ) 80 Nb 4 B 14 Si 2 amorphous magnetic ribbon (AMR) in the as-cast state and upon conventional (T CA ) and strain (T SA ) annealing heat treatment is investigated. From ribbon samples in as-cast condition, quenched in stress from planar flow casting (PFC) induced as-cast curvature derived uniaxial magnetic anisotropy. Stress relief by conventional furnace annealing at T CA > 350 °C achieved isotropic properties in the bulk. Annealing about the primary crystallization temperature, T CA ~ 450 °C, resulted in the formation of both FCC and BCC nanocrystallites and evolution to isotropic bulk magnetic properties confirming the random anisotropy model. In samples strain annealed at T SA = 440 °C at various tensions, relatively large controlled induced uniaxial anisotropy is achieved. The largest magnetic anisotropy occurs in annealing under the stress of 250 MPa yielding an anisotropy field of 7.1 x 10 4 A/m. Surface anisotropy observed by MOKE differs from bulk anisotropy due to image contrast from closure domains. Epoxy coatings are important for improved bonding, mechanical properties, and resistivity in tape-wound MANC cores for HSMs. Using a sessile droplet method, the equilibrium contact angle of an epoxy droplet on a tensile stress annealed MANC exhibits stress dependent surface energies. Anisotropic wetting in FeNi-based MANC heat treated at T CA = 440 °C mimics surface magnetic anisotropy observed by MOKE.

soft magnetic materials↗
DOE OSTI2021

Fracture toughness evaluations for spent nuclear fuel dry storage canister welds and spent nuclear fuel clad-pellet structures

Integrity of spent nuclear fuel (SNF) interim storage canisters is very important to the safety of the back-end nuclear fuel cycle. Stress corrosion cracking (SCC) potential of interim storage canister has been considered as a high priority. Because no post-weld heat treatment was required for forming these canisters, the high tensile residual stress existed within these canister welds. This can change the fracture resistance capacity significantly as well as increase SCC potential. Due to relative thin shell thickness of a canister weldment, the spiral notch torsion test (SNTT) method was used to estimate the canister weldment fracture toughness. SNTT was developed to measure the intrinsic fracture toughness of structural materials using small specimens. The SNTT method has been applied to a wide variety of structural materials, such as low-alloy steels, stainless steel, aluminum alloy, ceramics, concrete, and composites. The SNTT system operates by applying pure torsion to cylindrical specimens with a notch line that spirals around the specimen at a 45° pitch. In order to carry out pure torsion load mode, biaxial tension/torsion tester was developed accordingly to perform SNTT protocol. Moreover, applying fracture mechanics approach to SNF system reliability investigation is warranted due to the inherent flaws and hydride structures existed in a SNF system after nuclear reactor operation. However, none of the existing fracture toughness data deal with fuel cladding specific geometry or spent fuel material conditions, such as cladding structure with the pellet-inserts and the associated pellet clad mechanical interactions induced mixed-mode damage mechanisms. Thus, the development of an intrinsic fracture mechanics approach that is suitable for SNF materials is needed. Furthermore, due to thin wall and small dimension of clad tubing structure, the SNTT method was used to estimate the clad tubing structure fracture toughness. Fracture testing were performed on the received stainless steel canister weldment, most SNTT weld samples fracture initiation sites are at heat-affected zone (HAZ) regions. The estimated fracture toughness J Q ’ for the baseline SS304 steel is at 283 kJ/m². The estimated JQ’ for the SS304/308 weld and baseline metals are 148 kJ/m 2 and 459 kJ/m 2 , respectively. Out of cell fracture testing for spent fuel structure were carried out on the surrogate rods made of Zr-4 clad and alumina inserts, the estimated fracture toughness values for baseline Zr-4 cladding with alumina-pellet inserts are: (1) For SNTT samples with a short or medium crack length, between 5.4-mm and 8-mm, the estimate J IQ upon fracture initiation for the baseline Zr-4 cladding is at 50 kJ/m 2 with 2-sigma uncertainty of 3.26 kJ/m 2 , and the associated K IQ is at 67.46 MPa$\sqrt{m}$; and (2) For SNTT samples with a long crack length, around 13-mm, the crack initialization is deviated from that of the Mode-I tensile fracture and appears to be a mixed-mode fracture of Mode I - tensile stress and Mode III - out of plane shear stress; the estimated J MQ is at 18.9 kJ/m 2 , the associated K MQ is at 41.4 MPa$\sqrt{m}$.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1997

Seedborne fungal contamination: consequences in space-grown wheat

Plants grown in microgravity are subject to many environmental stresses that may promote microbial growth and result in disease symptoms. Wheat (cv. Super Dwarf) recovered from an 8-day mission aboard a NASA (National Aeronautics and Space Administration) space shuttle showed disease symptoms, including girdling of leaf sheaths and chlorosis and necrosis of leaf and root tissues. A Neotyphodium species was isolated from the seed and leaf sheaths of symptomatic wheat used in the spaceflight mission. Certain isozymes of a peroxidase unique to extracts from the microgravity-grown plants were observed in extracts from earth-grown Neotyphodium-infected plants but were not present in noninfected wheat. The endophytic fungus was eliminated from the wheat seed by prolonged heat treatment at 50 degrees C followed by washes with water at 50 degrees C. Plants from wheat seed infected with the Neotyphodium endophyte were symptomless when grown under greenhouse conditions, whereas symptoms appeared after only 4 days of growth in closed containers. Disease spread from an infected plant to noninfected plants in closed containers. Dispersion via spores was found on asymptomatic plants at distances of 7 to 18 cm from infected plants. The size and shape of the conidia, mycelia, and phialide-bearing structures and the ability to grow rapidly on carbohydrates, especially xylose, resembled the characteristics of N. chilense, which is pathogenic on orchard grass, Doctylis glomerati. The Neotyphodium wheat isolate caused disease symptoms on other cereals (wheat cv. Malcolm, orchard grass, barley, and maize) grown in closed containers.

NASA Discipline Plant Biology↗
DOE OSTI2024

Production of Carbon Nanomaterials and Sorbents from Domestic U.S. Coal (Final Report)

The main goal of this project was to produce high-value carbon nanomaterials and carbon sorbents from domestic coal resources in a cost-effective manner. Four types of domestic coal samples were processed through a combination of deashing, devolatilization, oxidation, reduction, and activation treatments to produce graphene oxide (GO), reduced graphene oxide (RGO), and activated carbon (AC). The precursors and developed materials were extensively characterized by various methods to investigate the impact of the coal feedstock type on the yield and quality of each product. A commercial graphite-based GO sample was included in the experimental work as the baseline material for comparison with the coal-based materials developed in this work. The performed work also included a technoeconomic analysis and cost estimation for a plant processing 20 tons/day coal, a market evaluation for the graphene materials, and a technology gap analysis. A simple process by concentrated nitric acid oxidation is used to oxidize coal precursors for the production of GO. Fine oxidized coal particles that were separated from larger oxidized coal particles had significantly higher oxygen contents and were identified as coal-based GO samples. Coarse oxidized coal particles were used as precursors for production of AC. Based on the Raman spectroscopy results, coal-based GO samples exhibited G and D bands similar to those of graphite-based GO samples. X-ray photoelectron spectroscopy revealed that coal-based GO samples had surface oxygen contents of ~26-35% that were higher than the oxygen contents of graphite-based GO samples. Larger particles of oxidized coal samples were activated under different conditions to produce high surface area functionalized AC. Prepared materials had surface areas exceeding 1,500 m 2 /g and pore volumes more than 1 cm 3 /g with different pore size distributions. Reduced graphene oxide samples were prepared by thermal reduction of both coal-based and graphite-based GO samples at 170-2800 ºC. Coal-based and graphite-based RGO samples exhibited similar carbon contents, Raman spectra, and XRD profiles. Heat treatment above 1500 ºC shifted RGO to synthetic graphite. Among anthracite, bituminous, subbituminous, and lignite coals tested, anthracite was the best precursor to produce carbon nanomaterials exhibiting properties similar to those of graphite-based materials. Anthracite-based carbon nanomaterials also had the highest production yields. Technoeconomic analysis estimated the production cost of GO and RGO for anthracite-based samples at about 2,600 and 4,200 $/ton, respectively, which is about two orders of magnitude lower than the current estimated price of graphite-based materials. Several gaps to further develop the proposed technology were identified and discussed that include process and equipment optimization, process integration, need for additional bench- and pilot-scale experiments, and other items to reduce the scale up risk. Market analysis reports suggested a compound annual growth rate of 40% for graphene and related materials. Short-term applications include composites, inks, and coatings. However, energy storage applications appear to be the dominant potential long-term applications. Different applications of coal-based GO and RGO need to be explored and clear metrics and standards for each application need to be developed.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Laboratory-Scale Coal-Derived Graphene Process (Final Report)

The Energy & Environmental Research Center (EERC) conducted a laboratory-scale coal-derived graphene (CDG) project focused on developing a technological process for making graphene from four U.S. domestic coal or coal wastes, including lignite from North Dakota, subbituminous coal from Wyoming, bituminous coal from Utah, and anthracite from Pennsylvania. The project was divided into two performance or budget periods (BPs), with BP1 comprising the up-front laboratory experiments to make graphene materials from coal beginning on May 1, 2020, to April 30, 2022. BP2 was conducted from May 1, 2022, to April 30, 2023, and was focused on analyzing the CDG process economic feasibility and the technical gaps for technological scale-up and commercialization. During this project, a few different coal-derived high-value products have been demonstrated, including graphite, graphene oxide (GO), reduced graphene oxide (rGO), and graphene quantum dots (GQDs). A new graphite microstructure was discovered and named “croissant graphite” because of the exterior morphological and textural resemblance to croissant food items sold in commercial groceries stores. The new graphite structure and the associated preparation from coal or coal waste feedstocks has been the subject of a U.S. patent application. The systematic experimental processes involving coal cleaning, upgrading, and conversion to high-value carbon products culminated into a developed upgraded coal-to-products (UCP) technology that is being pursued for potential fast-track commercialization, if funding is available. It is envisioned that commercialization of the UCP technology would increase consumption of U.S. domestic coals or coal wastes to make environmentally sustainable high-value products for the electronics industry, high-energy-storage applications, and clean energy technologies such as electric vehicle (EV) lithium-ion batteries (LIBs), for which graphite has become a critical mineral commodity. Croissant graphite microstructures, when observed by field emission scanning electron microscopy (FESEM), display wavy surface morphology and often grow from a base that is made of graphitized particles with honeycomb-like layers, which are believed to be graphene layers. While more studies are needed to fully ascertain the mechanisms of the croissant graphite microstructure formation, it is postulated that their growth may begin from curling of the graphene sheets into ribbon-like structures, and continuous growth and densification of the ribbon-like structures forms croissant microstructures. Additional studies are ongoing to evaluate the electrochemical performance of croissant graphite for LIB applications and to determine the experimental conditions necessary to tune on/off croissant formation so that it can be either optimized or suppressed depending on performance evaluation results. In addition to the discovery of croissant graphite, the graphitization process from the four coal ranks in general was successful. X-ray diffraction (XRD) analysis showed that the degree of graphitization (DoG) ranged from 12% to 80% in an early sample set, and further optimization on lignite coal produces a DoG of about 92%, which was spectacular to see as lignite is the lowest-rank coal. Thus, it is expected that the graphitization performance for higher-rank coals will be similar or better when optimized as well. The coal-derived graphite was used to make GO and rGO. Analytical characterization, e.g., by methods such as Raman spectroscopy, XRD, Fourier transform infrared (FTIR) spectroscopy and FESEM, showed that the sequence of converting the coal to graphite, exfoliating it to GO, and then chemically reducing the GO to rGO was successful. Although coal naturally contains aromatic compounds and some relatively small-sized condensed aromatic units, it does not contain graphene sheets. In the UCP process, the aromatic domains in the coals, particularly low-rank coals, are concentrated and condensed further into graphene sheets, which are ordered into a 3D stack during graphitization. The synthesized graphite is then unpacked by methods such as exfoliation to various graphene products. GQDs were synthesized from all four coal types, and their optical properties were demonstrated to be tunable by the coal precursor preprocessing treatments. In all four coal types, enhanced optical properties were observed for the produced GDQs with incremental improvements made to the coal precursors. GQDs produced from raw coal samples displayed lower ultraviolet–visible (UV–Vis) spectroscopy absorbance intensity compared to those obtained from cleaned and upgraded coal residues. The photoluminescence (PL) intensities also varied with pretreatment conditions and with the concentration of GQDs in aqueous solutions. GQDs obtained from anthracite show longer emission wavelengths and can be excited by visible light as opposed to GQDs derived from the other coal ranks. UV fluorescence 3D maps and spectra revealed that the emission wavelength at which the GQDs solutions display the highest intensity was slightly redshifted based on the coal precursor pretreatments. In low-rank coal (lignite and subbituminous) samples, two clusters were observed in the maps for GQDs, which may suggest that there are potentially two types of fluorophores in solution or two main size populations. The ability to tune the properties of GQDs based on processing methods can be exploited to make GQDs for various optical display or optoelectronics applications. The results also highlight the importance of removing coal-borne impurities to improve the quality of the coal precursor for preparation of graphene products. Coal and/or coal wastes preprocessing methods were developed and applied to clean and upgrade the coal precursors prior to graphitization and subsequent conversion to graphene products. The preprocessing methods involve high specific-gravity separations, mineral acid cleaning (no hydrofluoric acid), and subsequent upgrading by reducing the coal-borne heteroatom (nitrogen, sulfur, and oxygen) content using proprietary chemical agents. Analytical characterization revealed that the preprocessing steps were successful, with ash reductions that range from 38% to 80% and residual ash content that was below the 5 wt% initial target. Based on proximate and ultimate analysis, the heteroatom reduction reactions produced upgraded coal residues with the oxygen content reduced by 8% to 24%, with additional reductions in the nitrogen and sulfur contents. An initial assessment of the waste streams from the UCP process shows very small to negligible environmental impact due to CO 2 , NO x , and SO x because most process steps are performed under inert atmosphere with argon. Consequently, reactive oxygen environments that tend to create these species are avoided. The inorganic and potentially hazardous species are released into aqueous waste streams that are easy to handle for proper disposal. The liquid waste streams were found to contain low-level concentrations of rare-earth elements (REEs), which could be concentrated and recovered as value-added by-products. Additionally, the volatile and gaseous fractions from carbonization and heat treatment contain useful organic compounds that can also be recovered as potential valuable by-products. Thus, the UCP technology is considered an environmentally sustainable and promising emerging technology for making high-value products from coal and coal wastes, with potential additional value-added by-products. Analysis of potential markets for the coal-derived carbon products shows a strong demand in both niche market sectors and across a wide variety of other industrial sectors. Graphite is currently considered a critical mineral commodity that has a large and growing demand in the LIB industry for EV applications. Based on data from Fortune Business Insights (2022) and Marketwatch (2023) reports, the average global graphite market is projected to reach about 33 billion by 2028, growing at a compound annual growth rate (CAGR) of about 7%, with much of this growth expected to be in the LIB industry. GO and rGO have strong market potentials in various application areas, such as coatings for anticorrosion, anti-icing, and antimicrobial protection, thermal barriers, wear resistance, sensors, additive manufacturing such as 3D inks, and others. GQDs are the emerging key player in the bioimaging, photovoltaics, and light-emitting diodes (LEDs) applications, with the potential to replace traditional semiconductor quantum dots (SQDs), which are based on metallic systems that are more toxic and more expensive. Biomedical applications of GQDs are becoming more attractive because of low to no toxicity and extremely low cost compared to SQDs. The major challenges for scale-up and commercialization of coal-derived carbon products such as graphene vary from the inherent attributes of graphene itself to reluctance to accept graphene in new manufacturing processes because of the uncertainty of the unknown. The 2D nature of graphene materials with a thickness of one atom presents significant challenges to proper handling/processing, and process scale-up becomes difficult because it requires high-end, expensive equipment, even for routine handling and analysis for quality assurance and control. Pristine graphene can also be extremely difficult to work into other matrices, thus hindering downstream processibility, especially at large scale. Currently, the cost of graphene and graphene products is still high and presents an economic risk that tends to slow down investment in scaling up emerging technologies. The lack of a standard for graphene materials for quality assurance and quality control poses a great challenge not only for the markets but also for commercialization efforts. A first-look economic feasibility analysis of the UCP technology provided valuable information that suggests the UCP process would be feasible, especially when it is scaled to a pilot scale and could be more competitive at the full scale. Graphitization was found to be the most energy-consuming and most capital-intensive step in the overall process. In small laboratory- and bench-scale experiments, labor is a significant contributor to the total process costs. Although these energy, capital, and labor constraints contribute to a higher selling price for the product, a preliminary economic model suggests that the process would be feasible at large scale when the process is fully integrated, optimized, and automated.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Development of Novel Ferritic-Martensitic Steels with Superior Creep Properties for Power Plant Applications

A creep resistant martensitic steel, CPJ-7, was developed with an operating temperature approaching 650°C. Subsequently, another creep resistant martensitic steel, JMP, was designed with the potential to operate at, or slightly above, 650°C. This report describes the development of these alloys from early iterations of CPJ steels to the final CPJ-7 formulation as well as the more heat resistant JMP steel formulation. The design originated from computational modeling for phase stability and precipitate strengthening using fifteen constituent elements. Approximately forty heats of CPJ and ten of JMP, each weighing ~7 kg, were vacuum induction melted. A computationally optimized heat treatment schedule was developed to homogenize the ingots prior to hot forging and rolling prior to final normalization and tempering. Overall, wrought and cast versions of CPJ-7 present superior creep properties when compared to wrought and cast versions of COST alloys for steam turbine and wrought and cast versions of P91/92 for boiler applications. For instance, the Larson Miller Parameter curve for CPJ-7 at 650°C almost coincides with that of COST E at 620°C. The prolonged creep life was attributed to slowing down the process of the destabilization of the MX and M 23 C 6 precipitates at 650°C. On the other hand, the cast version of CPJ-7 also revealed superior mechanical performance, well above commercially available cast 9% Cr martensitic steel or derivatives, especially for creep life at 650°C. The casting process employed slow cooling to simulate the conditions of a thick wall full-size steam turbine casing but utilized a separate homogenization step prior to final normalization and tempering. To advance the development of CPJ-7 for commercial applications, a process was used to scale up the production of the alloy using vacuum induction melting (VIM) and electroslag remelting (ESR), which underlined the importance of melt processing control of intentionally designed minor and trace elements in these advanced alloys. Following the work on CPJ-7, the JMP steels were designed with higher Co for increased solid solution strengthening, Si for oxidation resistance and increased W (with low Mo content) for matrix strength and stability as well as solid solution strengthening. The JMP steels showed increases in creep life compared to CPJ-7 between 118 to 150% at 650°C for testing at various stresses between 138 MPa and 207 MPa. On a Larson-Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN and other MARBN-type steels. The influence of various elements within the composition of the alloys on the microstructure and mechanical properties are discussed. This report presents approximately 420,000 h of in-house creep testing, the equivalent of almost 50 years of cumulative creep tests.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Sintering-based Metal Additive Manufacturing Methods for Magnetic Materials

In this chapter, we review the relationship between solid-state sintering and additive manufacturing (AM) methods for fabricating soft and hard magnetic materials. Heat treatment as a post-processing method has been done in conjunction with AM as a method to improve density and/or mechanical properties. In binder jetting (BJT) of metal powders, sintering is a crucial post-processing step and is necessary for obtaining the final product. This is because the parts are only in the “green” state when they leave the BJT printer, with poor mechanical properties and high porosity. Sintering densifies and strengthens the green part into the final product. A potential industrial application for sintering-based AM is the fabrication of magnetic materials. The motivation for doing so, the process and properties of the AM magnets, and the potential applications of post-sintered AM magnets are explored.

Wang, Haobo↗
DOE OSTI2024

Effect of Zn Addition on Phase Evolution in AlCrFeCoNiZn High–Entropy Alloy

The addition of Zn to AlCrFeCoNi high-entropy alloy (HEA) poses intriguing questions as to how it would affect phase evolution. Herein, the phase evolution in AlCrFeCoNiZn is studied using a combination of experimental techniques (X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and differential scanning calorimetry) and computational (density-functional theory [DFT], calculation of phase diagrams, and machine-learning) methods. Mechanically alloyed and spark-plasma-sintered AlCrFeCoNiZn assumes a metastable single-phase, body-centered-cubic (BCC) structure that undergoes diffusion-controlled phase separation upon subsequent heat treatment to form separate (Al, Cr)-rich, (Fe, Co)-rich, and (Zn, Ni)-rich phases. The formation of (Al, Cr)-rich phase, not reported previously in AlCrFeCoNi-based HEAs, is attributed to strong clustering tendency of Cr–Zn and Cr–Ni pairs, combined with the strong ordering of Zn–Ni pair, driving out Cr that in turn combines with Al to form a (Al, Cr)-rich phase. In the DFT results, the formation of thermodynamically stable L1 2 phase is shown wherein Cr–Fe–Zn [Al–Ni-Co] preferably occupy1a (000) [3c (0 ½ ½)] positions. Furthermore, the sluggish diffusional transformation to L1 2 phase from BCC precursors is attributed to the small stacking-fault energy of AlCrFeCoNiZn. The equilibrated HEA exhibits a high microhardness of 8.24 GPa with an elastic modulus of 184 GPa.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Porphyrin Aerogel Catalysts for Oxygen Reduction Reaction in Anion-Exchange Membrane Fuel Cells

Platinum group metal (PGM)-free catalysts for oxygen reduction reaction have shown high oxygen reduction reaction activity in alkaline media. In order to further increase the power density of anion-exchange membrane fuel cells (AEMFCs), PGM-free catalysts need to have a high site density to reach high current densities. In this work, synthesis, characterization, and utilization of heat-treated iron porphyrin aerogels are reported as cathode catalysts in AEMFCs. The heat treatment effect is thoroughly studied and characterized using several techniques, and the best performing aerogel is studied in AEMFC, showing excellent performance, reaching a peak power density of 580 mW cm –2 and a limiting current density of as high as 2.0 A cm –2 , which can be considered the state-of-the-art for PGM-free based AEMFCs.

25 ENERGY STORAGE↗
DOE OSTI2021

High-Speed Ionic Synaptic Memory Based on 2D Titanium Carbide MXene

Synaptic devices with linear high-speed switching can accelerate learning in artificial neural networks (ANNs) embodied in hardware. Conventional resistive memories however suffer from high write noise and asymmetric conductance tuning, preventing parallel programming of ANN arrays. Electrochemical random-access memories (ECRAMs), where resistive switching occurs by ion insertion into a redox-active channel, aim to address these challenges due to their linear switching and low noise. ECRAMs using 2D materials and metal oxides however suffer from slow ion kinetics, whereas organic ECRAMs enable high-speed operation but face challenges toward on-chip integration due to poor temperature stability of polymers. Here, ECRAMs using 2D titanium carbide (Ti 3 C 2 T x ) MXene that combine the high speed of organics and the integration compatibility of inorganic materials in a single high-performance device are demonstrated. These ECRAMs combine the speed, linearity, write noise, switching energy, and endurance metrics essential for parallel acceleration of ANNs, and importantly, they are stable after heat treatment needed for back-end-of-line integration with Si electronics. The high speed and performance of these ECRAMs introduces MXenes, a large family of 2D carbides and nitrides with more than 30 stoichiometric compositions synthesized to date, as promising candidates for devices operating at the nexus of electrochemistry and electronics.

2D materials↗
DOE OSTI2024

Ink Casting and 3D‐Extrusion Printing of Yb 14 MnSb 11 for High‐Temperature Thermoelectric Material

Abstract Complex shapes are created from Yb 14 MnSb 11 , a high‐temperature thermoelectric Zintl phase, via a two‐step process: i) layer‐by‐layer 3D‐extrusion of ink containing partially‐reacted powders which are ball‐milled from a blend of Yb, MnSb, and Sb powders; ii) heat treatment to synthesize the ternary compound Yb 14 MnSb 11 and densify the extruded powders. A high phase purity for Yb 14 MnSb 11 (83–94%) is achieved in both cast and 3D‐extruded ink specimens via a solid‐state reaction between Yb, MnSb, and Yb 4 Sb 3 during reactive sintering. Pressure‐free sintering at temperatures of 1200–1400 °C densifies the powders to 82% relative density but can also induce the decomposition of the Yb 14 MnSb 11 phase due to Yb sublimation. A process window with optimized sintering temperature and time is identified, achieving both low porosity and high phase purity and reaching a maximum zT = 0.61 at 1000 °C, about half of the maximum zT value for bulk Yb 14 MnSb 11 made via conventional processes (pressure sintering of precursor powders). The present approach – direct ink writing of ball‐milled powders, combined with reactive sintering – is a scalable and affordable method to fabricate thermoelectric legs with intricate 3D shapes, for enhanced performances in high‐temperature thermoelectric applications.

Chen, Ming [Department of Materials Science &amp, ↗
DOE OSTI2020

Rafting-Enabled Recovery Avoids Recrystallization in 3D-Printing-Repaired Single-Crystal Superalloys

The repair of damaged Ni-based superalloy single-crystal turbine blades has been a long-standing challenge. Additive manufacturing by an electron beam is promising to this end, but there is a formidable obstacle: either the residual stress and γ/γ' microstructure in the single-crystalline fusion zone after e-beam melting are unacceptable (e.g., prone to cracking), or, after solutionizing heat treatment, recrystallization occurs, bringing forth new grains that degrade the high-temperature creep properties. Here, a post-3D printing recovery protocol is designed that eliminates the driving force for recrystallization, namely, the stored energy associated with the high retained dislocation density, prior to standard solution treatment and aging. The post-electron-beam-melting, pre-solutionizing recovery via sub-solvus annealing is rendered possible by the rafting (i.e., directional coarsening) of γ' particles that facilitates dislocation rearrangement and annihilation. The rafted microstructure is removed in subsequent solution treatment, leaving behind a damage-free and residual-stress-free single crystal with uniform γ' precipitates indistinguishable from the rest of the turbine blade. Finally, this discovery offers a practical means to keep 3D-printed single crystals from cracking due to unrelieved residual stress, or stress-relieved but recrystallizing into a polycrystalline microstructure, paving the way for additive manufacturing to repair, restore, and reshape any superalloy single-crystal product.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Radiation‐Resistant Aluminum Alloy for Space Missions in the Extreme Environment of the Solar System

Future human exploration of the solar system demands advanced materials capable of withstanding extreme environments, particularly exposure to solar energetic particle radiation. Current material selection criteria for space applications prioritize a high strength-to-weight ratio, high corrosion resistance and manufacturability, favoring age-hardenable Al-based alloys. However, conventional precipitation-hardened Al alloys suffer from irradiation-assisted dissolution of strengthening phases at doses as low as 0.2 displacements-per-atom (dpa), undermining their performance. Furthermore, these alloys develop radiation-induced defects, such as dislocation loops and voids, even at low doses. This study presents a novel ultrafine-grained (UFG) Al-based alloy, designed using the crossover alloying concept and strengthened by T-phase precipitates, featuring a chemically-complex structure with 162 atoms in its unit cell composed of Mg 32 (Zn,Al) 49 . It is showed that T-phase precipitates have exceptional radiation tolerance up to 24 dpa. Owing to the nanoscale UFG structure, dislocation loops are suppressed, and voids are only observed beyond 75 dpa. Microtensile tests up to 20 dpa confirm the preservation of mechanical performance under irradiation. The results underline the potential of this alloy as a radiation-resistant, lightweight material for future space applications. Three key strategies enable this performance: (i) stabilization of a UFG microstructure, (ii) T-phase precipitation featuring a highly negative Gibbs free energy and chemically-complex giant unit cell, and (iii) precise process control to prevent grain growth during heat treatment and irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Pristine Interface between Lithium Lanthanum Zirconate and Lithium Manganese Oxide by Pulsed Laser Deposition

Solid state lithium-ion batteries have garnered increasing interest in recent years due to several potential advantages over liquid-electrolyte based systems. The possibility of integrating the lithium garnet oxide, Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 (LLZTO), with the high voltage cathode, spinel Li x Mn 2 O 4 (LMO), is evaluated here. Thin film bilayer structures are prepared by pulsed laser deposition on MgO (001) substrates and characterized by x-ray diffraction and transmission electron microscopy. The LLZTO is grown by an alternating layer-by-layer deposition of LLZTO and Li 3 N and subsequently annealed for several hours at 575 °C to promote crystallinity. Growth of crystalline LMO with a pristine interface to LLZTO is achieved by gentle heat treatment (500 °C) to remove surface carbonate from the electrolyte and by cathode growth at a low temperature of 250 °C. Higher temperature depositions (330 – 450 °C) result in reaction between the two materials and the appearance of Li 2 MnO 3 , which may be in part due to the presence of excess lithium in the electrolyte layer. Because fully lithiated LiMn 2 O 4 has a voltage of ≈3.7 V versus Li+/Li, the observation of a well-defined interface, free of impurity phases and with no interdiffusion of elements, indicates LLZTO is stable to at least 3.7 V.

Garnet LLZO↗
DOE OSTI2025

Entrapment Behavior of Solid Surrogate Fission Products at Engineered UN Nano‐Hetero‐Interfaces Within Metallic Nuclear Fuels

Nanometric hetero-interfaces provide a wealth of scientific and engineering opportunities due to their complex and often misunderstood properties that can differ from their respective bulk constituents. In this work, the ability for engineered nanostructures within a bulk U─Mo alloy to arrest simulant fission products is investigated experimentally and computationally. Nanostructured 90 wt% U/ 10 wt% Mo (U-10Mo) with 7.1 at% Nd is consolidated using spark-plasma- sintering (SPS) techniques and is heat-treated at 500 °C under vacuum for 24, 100, 500, and 1000 h. Analysis on the sintered and heat-treated U-10Mo reveals rapid kinetics in Nd diffusion to nanocluster sites, with evidence of Nd diffusion occurring during sintering and during the following heat-treatment. The segregation behavior of Nd at two different U─Mo/UN interfaces is computationally verified using density functional theory (DFT) to reinforce experimental data.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Refractive Index and Abbe Number Tuning via 3D Printable Optical Quality Silica–Titania–Germania Glasses

The development of optical quality GeO 2 –TiO 2 –SiO 2 glasses compatible with direct ink writing (DIW) 3D printing is reported in this study. Colloidal GeO 2 and TiO 2 –SiO 2 core–shell feedstocks are prepared by a sol–gel method and converted to printable inks for DIW. Printed inks are subsequently densified to glass using heat treatment at temperatures up to 1100 °C in air. A series of print‐compatible glass compositions are prepared, yielding transparent glass with the highest refractive index n = 1.576. Herein, it is shown that more TiO 2 can be incorporated into the glass without haziness or scattering through the addition of GeO 2 . The mechanisms for this are discussed, and it is shown that crystallization persists in these glasses despite the lack of visible light scattering. Finally, the combination of both TiO 2 and GeO 2 into a ternary glass also is used to independently tune the dispersion properties of the glass, as demonstrated by measured refractive indices and Abbe numbers, which has potential implications for 3D‐printed optics.

36 MATERIALS SCIENCE↗