Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alternative Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41

A Study of Propane Combustion in a Spark-Ignited Cooperative Fuel Research (CFR) Engine

Liquefied petroleum gas (LPG), whose primary composition is propane, is a promising candidate for heavy-duty vehicle applications as a diesel fuel alternative due to its CO 2 reduction potential and high knock resistance. To realize diesel-like efficiencies, spark-ignited LPG engines are proposed to operate near knock-limit over a wide range of operating conditions, which necessitates an investigation of fuel-engine interactions that leads to end-gas autoignition with propane combustion. This work presents both experimental and numerical studies of stoichiometric propane combustion in a sparkignited (SI) cooperative fuel research (CFR) engine. Engine experiments are initially conducted at different compression ratio (CR) values, and the effects of CR on engine combustion are characterized. A three-pressure analysis (TPA) model based on the two-zone combustion concept is developed in GT-Power and validated using test results to estimate in-cylinder wall temperatures, residual gas fraction, etc. This model is further utilized to examine end-gas chemistry by enabling the SI turbulent flame combustion and unburned gas chemical kinetics modules. Finally, a three-dimensional (3D) computational fluid dynamic (CFD) model of the CFR engine is developed in CONVERGE, where the G-equation and SAGE detailed chemical kinetics models are implemented for combustion modeling. Here, a 153 species reduced chemical kinetics mechanism derived from the detailed NUIGMech1.1 mechanism based on the ignition delay and laminar flame speed (LFS) studies is used to generate an LFS lookup table and to describe end-gas autoignition chemistry. Multi-cycle Reynolds-averaged Navier-Stokes (RANS) simulations are then performed for the tested CRs, and the numerical model is shown to be capable of predicting the propane combustion characteristics, particularly the end-gas autoignition behavior.

20 FOSSIL-FUELED POWER PLANTS↗

US Clean Energy Sector and the Opportunity for Modeling and Simulation

The following paper sets forth the current understanding of the US clean energy demand and opportunity. As clean energy systems come online and technology is developed, modeling and simulation of these complex energy programs provides an untapped business opportunity. The US Department of Defense provides a great venue for developing new technology in the energy sector because it is demanding lower fuel costs, more energy efficiencies in its buildings and bases, and overall improvements in its carbon footprint. These issues coupled with the security issues faced by foreign dependence on oil will soon bring more clean energy innovations to the forefront (lighter batteries for soldiers, alternative fuel for jets, energy storage systems for ships, etc).

Inge, Carole Cameron↗

Updating the U.S. Life Cycle GHG Petroleum Baseline to 2014 with Projections to 2040 Using Open-Source Engineering-Based Models

Here, the National Energy Technology Laboratory produced a well-to-wheels (WTW) life cycle greenhouse gas analysis of petroleum-based fuels consumed in the U.S. in 2005, known as the NETL 2005 Petroleum Baseline. This study uses a set of engineering-based, open-source models combined with publicly available data to calculate baseline results for 2014. An increase between the 2005 baseline and the 2014 results presented here (e.g., 92.4 vs 96.2 g CO 2 e/MJ gasoline, + 4.1%) are due to changes both in modeling platform and in the U.S. petroleum sector. An updated result for 2005 was calculated to minimize the effect of the change in modeling platform, and emissions for gasoline in 2014 were about 2% lower than in 2005 (98.1 vs 96.2 g CO 2 e/MJ gasoline). The same methods were utilized to forecast emissions from fuels out to 2040, indicating maximum changes from the 2014 gasoline result between +2.1% and –1.4%. The changing baseline values lead to potential compliance challenges with frameworks such as the Energy Independence and Security Act (EISA) Section 526, which states that Federal agencies should not purchase alternative fuels unless their life cycle GHG emissions are less than those of conventionally produced, petroleum-derived fuels.

54 ENVIRONMENTAL SCIENCES↗

Requesting an Exemption from Standard Compliance

This document provides guidance for state and alternative fuel provider fleets covered by the Energy Policy Act to understand how to file a request for exemption from Standard Compliance requirements.

33 ADVANCED PROPULSION SYSTEMS↗

Effects of isopropanol-butanol-ethanol and diesel fuel blends on combustion characteristics in a constant volume chamber

Acetone-butanol-ethanol (ABE) has been directly used in modern engines as a way to eliminate the high separation cost during the butanol fermentation process. However, further development of ABE could be restricted by the corrosiveness of acetone in the mixture. By converting ABE into Isopropanol-Butanol-Ethanol (IBE) in a single biochemical step, a different yet more stable alternative fuel could be available. This study is aimed to investigate the performance, combustion, and soot luminosity of a constant volume chamber fueled with varying ratios of IBE and diesel. IBE blended at 20% and 40% with 80% and 60% diesel, by volume respectively, and neat diesel were compared under various ambient oxygen and temperature conditions. Overall, the IBE-diesel blends were able to maintain combustion and spray characteristics similar to that of neat diesel while at the same time reducing soot. However, at lower temperatures and oxygen concentrations, the IBE-diesel blends show higher ignition delays which affect the combustion.

42 ENGINEERING↗

Electrogenerative Reactors for Process Intensified Cogeneration of Power and Liquid Fuel from Shale Gas

With the abundance of natural gas and its primary components of methane, ethane and propane, there is the opportunity to convert these light alkanes to higher-value products. The growth in natural gas supply in the U.S. has increased substantially since the mid-2000s due to advances in horizontal drilling and hydraulic fracturing. As petroleum prices are volatile, natural gas resources are progressively attractive as alternative fuel sources. However, many of these shale gas wells are in regions of the U.S. that are remote and costly to transport to petrochemical and refining centers. In addition, much of this shale gas is “wet gas” that contains condensable amounts of ethane. While dedicated ethane gas pipelines have been built to get a small fraction of this gas to market, they are very capital intensive and compete for existing land use. As a result of this Phase I project, we developed a process to convert ethane to a transportable liquid fuel. This was achieved by implementing process intensification for this gas-to-liquids approach; we use novel eletrogenerative reactors in a two-step process rather than multi-step well-known technologies such as Fisher-Tropsch synthesis. These reactors borrow on well proven solid oxide fuel cell technology. Therefore, when produced in mass will be a very low-cost modular chemical reactor. This project demonstrated that EcoCatlaytic’s catalysts are highly selective towards ethylene and are compatible with anode materials. These integrated catalysts with the anode were able to maintain stable activity under ethane. Process simulations demonstrate an energy savings while producing gasoline and electricity for a modular system that produces 1,000 bbl/day gasoline. The system, not only produces gasoline, but also generates electricity which is a very valuable commodity in the remote shale gas facilities. This process could potentially allow remote natural gas producers to upgrade their feedstock to valuable gasoline on-site rather than flaring.

03 NATURAL GAS↗

High Temperature Steam Oxidation Testing of Candidate Accident Tolerant Fuel Cladding Materials

The Fuel Cycle Research and Development (FCRD) program’s Advanced Fuels Campaign has initiated a multifold effort aimed at facilitating development of accident tolerant fuels in order to overcome the inherent shortcomings of light water reactor (LWR) fuels when exposed to beyond design basis accident conditions. The campaign has invested in development of experimental infrastructure within the Department of Energy complex capable of chronicling the performance of a wide range of concepts under prototypic accident conditions. This report summarizes progress made at Oak Ridge National Laboratory (ORNL) and Los Alamos National Laboratory (LANL) in FY13 toward these goals. Alternative fuel cladding materials to Zircaloy for accident tolerance and a significantly extended safety margin requires oxidation resistance to steam or steam-H 2 environments at ≥1200°C for short times. At ORNL, prior work focused attention on SiC, FeCr and FeCrAl as the most promising candidates for further development. Also, it was observed that elevated pressure and H2 additions had minor effects on alloy steam oxidation resistance, thus, 1 bar steam was adequate for screening potential candidates. Commercial Fe-20Cr-5Al alloys remain protective up to 1475°C in steam and CVD SiC up to 1700°C in steam. Alloy development has focused on Fe-Cr-Mn-Si-Y and Fe-Cr-Al-Y alloys with the aluminaforming alloys showing more promise. At 1200°C, ferritic binary Fe-Cr alloys required ≥25% Cr to be protective for this application. With minor alloy additions to Fe-Cr, more than 20%Cr was still required, which makes the alloy susceptible to α’ embrittlement. Based on current results, a Fe-15Cr-5Al-Y composition was selected for initial tube fabrication and welding for irradiation experiments in FY14. Evaluations of chemical vapor deposited (CVD) SiC were conducted up to 1700°C in steam. The reaction of H 2 O with the alumina reaction tube at 1700°C resulted in Al(OH) 3 formation, which reacted with the specimen to form a liquid reaction product. This behavior was not observed at lower temperatures where gas velocity and H 2 O content showed typical effects on the reaction rate. For LANL, the capabilities for oxidation testing as well as exploration of a methodology for measurement of hydrogen production of samples during oxidation under water vapor atmospheres is discussed. Results obtained for available commercial alloys are summarized, and data highlighting the performance of molybdenum, a recently proposed cladding material, are presented. Finally, leveraging of these techniques in conjunction with current and companion FCRD programs is discussed with respect to work in FY14.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Studying converging shock collisions in novel hybrid-drive shock ignition geometries

Recent Inertial Confinement Fusion (ICF) experiments using a “high-foot” implosion at the National Ignition Facility (NIF) have demonstrated the importance of hydrodynamic stability in these systems by reaching the alpha heating regime and setting new records of energy gain. The high-foot platform is not predicted to achieve ignition, however, and consequently must sacrifice some stability for increased kinetic energy delivered to the fuel in experiments planned for the near future as an optimal, ignition achieving target design is searched for. Given that the high-foot fuel implosion velocity was measured to reach 310 km/s (390 TW, 1.8 MJ 3-­shock pulse) whereas the low-­foot, high mix implosions of the original National Ignition Campaign (NIC) reached 350 km/s (420 TW, 1.6 MJ 4-­shock pulse) with a predicted velocity requirement of 370 km/s (based on 2-­D simulations used to define an Ignition Threshold Factor) we are left with an extremely narrow margin for success just by optimizing between the high and low-foot platforms. There is hope that alternate ablators will also provide some performance improvements, but it appears likely that no manifestation of the conventional indirect-­drive central hotspot implosion scheme (C-­ICF) will work with the current available facility energy. This by itself motivates the need to seek alternate fuel assembly concepts that can be fielded on NIF in the near future. At a fundamental level Shock Ignition (SI) is predicted to make more efficient use of the total energy available from the driver (i.e. NIF or OMEGA) and to result in higher gains needed for energy production, which makes it a likely candidate as an alternative ignition approach. The direct irradiation of the capsule to drive the implosion, however, is untested at ignition-­scale and poses numerous difficulties on NIF. If the implosion was driven using a hohlraum (indirectly) instead followed by direct laser irradiation of the imploded capsule to launch the ignitor shock (as illustrated in the upper panel of Fig. 1) then this form of Shock Ignition could fit well into the NIF environment. The primary objective of this project is to develop and test a hybrid drive implosion concept on OMEGA to study its merits and weaknesses for eventual trial on NIF. A key question that remains with regards to Shock Ignition, in general, is the effect of low­-mode asymmetries on the transfer of energy during collision of the rebounding and ignitor shocks. Our second objective is to field a directed experiment designed to study asymmetric converging shock collision and their effect on hot spot formation. The proposed experiments are part of a current LANL Laboratory Directed Research and Development (LDRD) project that we are using to develop ignition-scale designs as well as for designing and carrying out the first implosion experiments as discussed below.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A high-performance intermediate temperature reversible solid oxide cell with a new barrier layer free oxygen electrode

The best solution to address the critical durability issue of solid oxide electrolytic cells (SOECs) for high-efficiency and high-rate H 2 production is to lower the operating temperature without sacrificing the performance. Developing high performance oxygen electrodes (OEs) is a key to capitalizing this solution. Here, in this paper, we report on a highly active OE for intermediate temperature ZrO 2 -based SOECs without a CeO 2 barrier layer. The new barrier-layer-free (BLF) OE is a composite of two materials, (Bi 0.75 Y 0.25 ) 0.93 Ce 0.07 O 1.5±δ (BYC) that exhibits high oxide-ion conductivity and La 0.8 Sr 0.2 MnO 3 (LSM) that possesses a high electronic conductivity to enable fast oxygen reduction/evolution reactions (ORR/OER). Featuring a microscale porous BYC scaffold decorated with high surface area LSM nanoparticles (NPs), the new BLF-OE exhibited a low area specific resistance (ASR) of 0.10 Ω cm 2 at 650 °C in air. With 50%H 2 -50%H 2 O as a feed to hydrogen electrode (HE) and air to OE, the single cell performance achieved 588 mA cm -2 at 0.80 V in the fuel cell mode and 688 mA cm -2 at 1.30 V in the electrolytic mode at 650 °C. Our in-house testing showed that this level of performance was ~3.5x higher than the cell with the benchmark La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ -Ce 0.9 Gd 0.1 O 2-δ OE. The long-term durability testing under alternating fuel cell and electrolytic modes showed a low degradation rate of 0.10 mA cm -2 h -1 over 550 hours. These encouraging results showed the great promise of the newly developed BYC-LSM to be an excellent OE candidate for intermediate temperature SOECs.

25 ENERGY STORAGE↗

Oak Ridge Reservation Annual Site Environmental Report for 2014

The US Department of Energy’s (DOE’s) Oak Ridge Reservation (ORR) is located in Roane and Anderson counties in East Tennessee, about 40 km (25 miles) from Knoxville. ORR is one of DOE’s most unique and complex sites. It encompasses three major facilities and thousands of employees that perform every mission in the DOE portfolio—energy research, environmental restoration, national security, nuclear fuel supply, reindustrialization, science education, basic and applied research in areas important to US security, and technology transfer. ORR was established in the early 1940s as part of the Manhattan Project for the purposes of enriching uranium and pioneering methods for producing and separating plutonium. Today, scientists at the Oak Ridge National Laboratory (ORNL), DOE’s largest multipurpose national laboratory, conduct world-leading research in advanced materials, alternative fuels, climate change, and supercomputing. The Y-12 National Security Complex (Y-12 or Y-12 Complex) is vital to maintaining the safety, security, and effectiveness of the US nuclear weapons stockpile and reducing the global threat posed by nuclear proliferation and terrorism. The East Tennessee Technology Park (ETTP), a former uranium enrichment complex, is being transitioned to a clean, revitalized industrial park.

54 ENVIRONMENTAL SCIENCES↗

Evaluation Metrics Applied to Accident Tolerant Fuels

The safe, reliable, and economic operation of the nation’s nuclear power reactor fleet has always been a top priority for the United States’ nuclear industry. Continual improvement of technology, including advanced materials and nuclear fuels, remains central to the industry’s success. Decades of research combined with continual operation have produced steady advancements in technology and have yielded an extensive base of data, experience, and knowledge on light water reactor (LWR) fuel performance under both normal and accident conditions. One of the current missions of the U.S. Department of Energy’s (DOE) Office of Nuclear Energy (NE) is to develop nuclear fuels and claddings with enhanced accident tolerance for use in the current fleet of commercial LWRs or in reactor concepts with design certifications (GEN-III+). Accident tolerance became a focus within advanced LWR research upon direction from Congress following the 2011 Great East Japan Earthquake, resulting tsunami, and subsequent damage to the Fukushima Daiichi nuclear power plant complex. The overall goal of ATF development is to identify alternative fuel system technologies to further enhance the safety, competitiveness and economics of commercial nuclear power. Enhanced accident tolerant fuels would endure loss of active cooling in the reactor core for a considerably longer period of time than the current fuel system while maintaining or improving performance during normal operations. The U.S. DOE is supporting multiple teams to investigate a number of technologies that may improve fuel system response and behavior in accident conditions, with team leadership provided by DOE national laboratories, universities, and the nuclear industry. Concepts under consideration offer both evolutionary and revolutionary changes to the current nuclear fuel system. Mature concepts will be tested in the Advanced Test Reactor at Idaho National Laboratory beginning in Summer 2014 with additional concepts being readied for insertion in fiscal year 2015. This paper provides a brief summary of the proposed evaluation process that would be used to evaluate and prioritize the candidate accident tolerant fuel concepts currently under development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Economic Analysis of Renewable Fuels for Marine Propulsion

The current global marine fuel consumption is estimated to be around 330 million tonnes annually, and the demand is expected to be doubled by 2030 due to increased global trade. Over 90% of the world's shipped goods travel by marine cargo vessels - one of the largest contributors to emissions of SOx, NOx, and PM. To meet the growing demand and the upcoming more stringent air emission regulations, now is the time to explore alternative fuels to penetrate the marine fuel markets. Biofuels can undoubtedly play an essential role in the future marine fuel that is more renewable, and lower sulfur and emissions. Both techno-economic analysis (TEA) and life cycle analysis (LCA) are effective tools to assess the economic and environmental feasibility of various biofuel pathways, in terms of their market competitiveness and environmental benefits concerning energy savings and air emissions reductions.

09 BIOMASS FUELS↗

Carbon-Fuelled Future

Whether due to changes in policy or consumption of available fossil fuels, alternative sources of energy will be required, especially given the rising global energy demand. However, one of the main factors limiting the widespread utilization of renewable energy, such as wind, solar, wave or geothermal, is our ability to store energy. Storage of energy from carbon-neutral sources, such as electricity from solar or wind, can be accomplished through many routes. One approach is to store energy in the form of chemical bonds, as fuels. The conversion of low-energy compounds, such as water and carbon dioxide, to higher energy molecules, such as hydrogen or carbon-based fuels, enables the storage of carbon-neutral energy on a very large scale. The author¹s work in this area is supported by the US Department of Energy Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory is operated by Battelle for the US Department of Energy.

CO2 reduction renewable energy↗

Recent contributions of flame-sampling molecular-beam mass spectrometry to a fundamental understanding of combustion chemistry

Flame-sampling molecular-beam mass spectrometry of premixed, laminar, low-pressure flat flames has been demonstrated to be an efficient tool to study combustion chemistry. In this technique, flame gases are sampled through a small opening in a quartz probe, and after formation of a molecular beam, all flame species are separated using mass spectrometry. The present review focuses on critical aspects of the experimental approach including probe sampling effects, different ionization processes, and mass separation procedures. The capability for isomer-resolved flame species measurements, achievable by employing tunable vacuum-ultraviolet radiation for single-photon ionization, has greatly benefited flame-sampling molecular-beam mass spectrometry. This review also offers an overview of recent combustion chemistry studies of flames fueled by hydrocarbons and oxygenates. The identity of a variety of intermediates in hydrocarbon flames, including resonantly stabilized radicals and closed-shell intermediates, is described, thus establishing a more detailed understanding of the fundamentals of molecular-weight growth processes. Finally, molecular-beam mass-spectrometric studies of reaction paths in flames of alcohols, ethers, and esters, which have been performed to support the development and validation of kinetic models for bio-derived alternative fuels, are reviewed.

10 SYNTHETIC FUELS↗

Review of Current State of the Art and Key Design Issues With Potential Solutions for Liquid Hydrogen Cryogenic Storage Tank Structures for Aircraft Applications

Due to its high specific energy content, liquid hydrogen (LH2) is emerging as an alternative fuel for future aircraft. As a result, there is a need for hydrogen tank storage systems, for these aircraft applications, that are expected to provide sufficient capacity for flight durations ranging from a few minutes to several days. It is understood that the development of a large, lightweight, reusable cryogenic liquid storage tank is crucial to meet the goals of and supply power to hydrogen-fueled aircraft, especially for long flight durations. This report provides an annotated review (including the results of an extensive literature review) of the current state of the art of cryogenic tank materials, structural designs, and insulation systems along with the identification of key challenges with the intent of developing a lightweight and long-term storage system for LH2. The broad classes of insulation systems reviewed include foams (including advanced aerogels) and multilayer insulation (MLI) systems with vacuum. The MLI systems show promise for long-term applications. Structural configurations evaluated include single- and double-wall constructions, including sandwich construction. Potential wall material candidates are monolithic metals as well as polymer matrix composites and discontinuously reinforced metal matrix composites. For short-duration flight applications, simple tank designs may suffice. Alternatively, for longer duration flight applications, a double-wall construction with a vacuum-based insulation system appears to be the most optimum design. The current trends in liner material development are reviewed in the case that a liner is required to minimize or eliminate the loss of hydrogen fuel through permeation.

Mital, Subodh K.↗

Hydrogen shift isomerizations in the kinetics of the second oxidation mechanism of alkane combustion. Reactions of the hydroperoxypentylperoxy OOQOOH radical

Hydroperoxyalkylperoxy species are important intermediates that are generated during the autoignition of transport fuels. In combustion, the fate of hydroperoxyalkylperoxy is important for the performance of advanced combustion engines, especially for autoignition. A key fate of the hydroperoxyalkylperoxy is a 1,5 H-shift, for which kinetics data are experimentally unavailable. In the present work, we study 1-hydroperoxypentan-3-yl)dioxidanyl (CH 3 CH 2 CH(OO)CH 2 CH 2 OOH) as a model compound to clarify the kinetics of 1,5 H-shift of hydroperoxyalkylperoxy species, in particular α-H isomerization and alternative competitive pathways. With a combination of electronic structure calculations, we determine previously missing thermochemical data, and with multipath variational transition state theory (MP-VTST), a multidimensional tunneling (MT) approximation, multiple-structure anharmonicity, and torsional potential anharmonicity, we obtained much more accurate rate constants than the ones that can computed by conventional single-structure harmonic transition state theory (TST) and than the empirically estimated rate constants that are currently used in combustion modeling. The roles of various factors in determining the rates are elucidated. The pressure-dependent rate constants for these competitive reactions are computed using system-specific quantum RRK theory. The calculated temperature range is 298–1500 K, and the pressure range is 0.01–100 atm. The accurate thermodynamic and kinetics data determined in this work are indispensable in the detailed understanding and prediction of ignition properties of hydrocarbons and alternative fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reducing greenhouse gas emissions for climate stabilization: framing regional options

The Intergovernmental Panel on Climate Change (IPCC) has stated that stabilizing atmospheric CO{sub 2} concentrations will require reduction of global greenhouse gas (GHG) emissions by as much as 80% by 2050. Subnational efforts to cut emissions will inform policy development nationally and globally. We projected GHG mitigation strategies for Minnesota, which has adopted a strategic goal of 80% emissions reduction by 2050. A portfolio of conservation strategies, including electricity conservation, increased vehicle fleet fuel efficiency, and reduced vehicle miles traveled, is likely the most cost-effective option for Minnesota and could reduce emissions by 18% below 2005 levels. An 80% GHG reduction would require complete decarbonization of the electricity and transportation sectors, combined with carbon capture and sequestration at power plants, or deep cuts in other relatively more intransigent GHG-emitting sectors. In order to achieve ambitious GHG reduction goals, policymakers should promote aggressive conservation efforts, which would probably have negative net costs, while phasing in alternative fuels to replace coal and motor gasoline over the long-term. 31 refs., 3 figs., 1 tab.

20 FOSSIL-FUELED POWER PLANTS↗

Green Aviation: Review, Aspirations, and Operational Improvements

Air traffic affects the environment locally, regionally and globally. Estimates show that aviation is responsible for 13% of transportation-related fossil fuel consumption and 2% of all anthropogenic CO2 emissions. Although there is considerable decline in air traffic due to COVID pandemic, Federal Aviation Administration (FAA) expects domestic air traffic to grow at an annual rate of 2.0 % over the next 20 years. Global air traffic is expected to grow more rapidly than domestic air traffic at an annual rate of 4.8% from 2011 to 2030. The desire to accommodate growing air traffic needs while limiting the impact of aviation on the environment has led to research in green aviation with the goals of better scientific understanding, utilization of alternative fuels, introduction of new aircraft technology, and rapid operational changes. Greenhouse gases, nitrogen oxides, and contrails generated by air traffic affect the climate in different and uncertain ways. Understanding the changes requires a hierarchy of models to deal with multiple disciplines, time scales ranging from few minutes to few hundred years and uncertainties in modeling parameters affecting both science and policy. This talk reviews earlier work at Ames on the modeling approach and an integrated capability to design aircraft operations based on a trade-off between fuel consumption, environmental goals and stakeholder values.

Green Aviation↗