Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additively Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 739 records · Page 41
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured Ni-based Alloys in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in elevated temperature and pressure direct-fired supercritical CO2 (sCO2) power cycles. Herein, the wrought product form of alloy H282, as well as several additional nickel-based commercial alloys (230, 263, 617, 625, 740H), were exposed to direct-fired supercritical CO2 conditions (95CO2 – 4H2O – 1O2) at 750 °C and 20 MPa for over 2,000 h. Additionally, additive manufactured (AM) 282 produced by laser powder bed fusion (LPBF) were also included in the exposures. This paper focuses primarily on the differences observed in the degradation behavior of the wrought and additively manufactured materials. AM samples in the as-printed state were found to form less protective oxide scales resulting in higher oxidation rates compared to wrought samples. However, applying a 600 grit surface finish to the AM samples modified the oxidation behavior to closely resemble that of the wrought material. The AM samples formed Mo-rich carbides in the alloy beneath the oxide following sCO2 exposure, implying potentially higher levels of carbon uptake relative to the wrought material. Conversely, the AM samples seemed to be less affected by water-assisted oxide volatilization compared to the wrought material. The results are discussed in terms of the potential compatibility issues that may arise when using Ni-based alloys in the hot portions of direct-fired sCO2 power cycles, particularly in the case of thin-walled components.

Carney, Casey↗
DOE OSTI2022

Compositional Effects of Additively Manufactured Refractory High-Entropy Alloys under High-Energy Helium Irradiation

High-Entropy Alloys (HEAs) are proposed as materials for a variety of extreme environments, including both fission and fusion radiation applications. To withstand these harsh environments, materials processing must be tailored to their given application, now achieved through additive manufacturing processes. However, radiation application opportunities remain limited due to an incomplete understanding of the effects of irradiation on HEA performance. In this letter, we investigate the response of additively manufactured refractory high-entropy alloys (RHEAs) to helium (He) ion bombardment. Through analytical microscopy studies, we show the interplay between the alloy composition and the He bubble size and density to demonstrate how increasing the compositional complexity can limit the He bubble effects, but care must be taken in selecting the appropriate constituent elements.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive manufacturing: Frameworks for chemical understanding and advancement in vat photopolymerization

Abstract Three-dimensional printing, or additive manufacturing (AM), is a broad term for a wide range of fabrication methods utilizing materials such as small-molecule, polymer, and metal feedstocks. Each method requires different chemical, physical, and engineering needs to be successful. This article will discuss some of the considerations for polymer-based AM methods. Ultimately, we focus on the chemistries of vat photopolymerization, in which light is used to cure a resin from liquid to solid, to provide an example of how chemical advancements have led to increased speed, resolution, and multimaterial printing capabilities not previously possible. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2020

Types of spatter and their features and formation mechanisms in laser powder bed fusion additive manufacturing process

Spatter causes defect formation, powder redistribution and contamination in laser powder bed fusion (LPBF) additive manufacturing process. It is critical to distinguish different types of spatter and understand their features and formation mechanisms. This work reveals the features and formation mechanisms of five unique types of spatter during the LPBF process by in-situ high-speed, high-energy x-ray imaging. Spatters observed during LPBF testing are quantified by their speed, size, and direction. Distinct quantifiable characteristics for each type of spatter are identified. Finally, effects of the laser power, scan speed, and ambient pressure on spatter formation and features are unraveled. A spatter formation map for AlSi10Mg alloy is constructed.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical rolling and annealing of wire-arc additively manufactured stainless steel plates

Thin walls of 304L stainless steel were fabricated by wire-arc additive manufacturing (WAAM) followed by post build thermomechanical processing to modify the as built microstructure and properties. The walls were made using a high-deposition-rate robotically controlled gas-metal arc welding system and were characterized using optical microscopy and tensile tested for mechanical properties. Post processing consisted of mechanical rolling the walls to 25% and 40% strains, followed by annealing at 1050°C to demonstrate a wide range of properties. Results show that WAAM can be used to build custom sized semi-finished parts or blanks that can later be thermomechanically processed to increase strength and ductility through recrystallization of the as built microstructure, and/or processed into desired shapes with improved mechanical properties.

304L stainless steel↗
DOE OSTI2021

Additively Manufactured NdFeB Polyphenylene Sulfide Halbach Magnets to Generate Variable Magnetic Fields for Neutron Reflectometry

Halbach arrays are the most efficient closed structures for generating directed magnetic fields and gradients, and are widely used in various electric machines. We utilized fused deposition modeling-based Big Area Additive Manufacturing technology to print customized, compensated concentric Halbach array rings, using polyphenylene sulfide-bonded NdFeB permanent magnets for polarized neutron reflectometry. The Halbach rings could generate a 0 ≤ B ≤ 0.30 T field, while preserving 90% polarization of an axial neutron beam. Polarized neutron beams are used to study a wide range of structural and magnetic phenomena spanning physics, chemistry, and biology. In this study, we demonstrate the effectiveness of additive manufacturing for producing prototype Halbach arrays, characterize their magnetic properties, and generated magnetic fields, and discuss the conservation of neutron beam polarization as a function of magnetic field.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of Part Size, Displacement Rate, and Aging on Compressive Properties of Elastomeric Parts of Different Unit Cell Topologies Formed by Vat Photopolymerization Additive Manufacturing

Due to its ability to achieve geometric complexity at high resolution and low length scales, additive manufacturing (AM) has increasingly been used for fabricating cellular structures (e.g., foams and lattices) for a variety of applications. Specifically, elastomeric cellular structures offer tunability of compliance as well as energy absorption and dissipation characteristics. However, there are limited data available on compression properties for printed elastomeric cellular structures of different designs and testing parameters. In this work, the authors evaluate how unit cell topology, part size, the rate of compression, and aging affect the compressive response of polyurethane-based simple cubic, body-centered, and gyroid structures formed by vat photopolymerization AM. Finite element simulations incorporating hyperelastic and viscoelastic models were used to describe the data, and the simulated results compared well with the experimental data. Of the designs tested, only the parts with the body-centered unit cell exhibited differences in stress–strain responses at different part sizes. Of the compression rates tested, the highest displacement rate (1000 mm/min) often caused stiffer compressive behavior, indicating deviation from the quasi-static assumption and approaching the intermediate rate response. The cellular structures did not change in compression properties across five weeks of aging time, which is desirable for cushioning applications. This work advances knowledge on the structure–property relationships of printed elastomeric cellular materials, which will enable more predictable compressive properties that can be traced to specific unit cell designs.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Simulation driven adaptive sampling for neutron-diffraction based strain mapping of additively manufactured parts

Neutron diffraction based strain mapping is a useful technique for measuring residual strains in additively manufactured (AM) metal parts. The measurement is traditionally done by scanning the sample in a point-wise raster pattern to extract the strain at each position. Since the overall scan can span several hours, adaptive sampling approaches using Bayesian optimization based on Gaussian process (BO-GP) regression have been introduced—demonstrating that even with a fraction of the typically made measurements the dominant strain patterns in the sample can be reconstructed. However, the parameters of the BO-GP algorithm have to be carefully chosen for best performance, and the movement time between arbitrary points can offset the time savings from a reduced number of measurement locations. In this paper, we propose algorithms to refine the BO-GP based methods by using simulations of strain patterns in AM parts based on the materials and the process used to print them. We demonstrate that the simulated strain patterns can be used to help choose better parameters for the BO-GP based framework—leading to low reconstruction error for the final strain pattern. Furthermore, we show that the strain mapping experiment can be initialized with a sampling pattern learnt from the simulation data and ordered to reduce movement time, dramatically enabling reduction in the overall time required to run the baseline BO-GP method.

Gaussian process regression↗
DOE OSTI2025

Benchmarking image processing techniques for porosity measurement in polymer additive manufacturing: Review and experimental analysis

An image processing workflow is proposed for porosity measurement in polymer additive manufacturing. Various techniques, including global and local thresholding, region growing, and K-means clustering, were applied to microscopic images of carbon fiber reinforced acrylonitrile butadiene styrene (CF-ABS) and benchmarked for their ability to accurately measure porosity. Global methods included Otsu, minimum error, iterative, and entropy-based thresholding, while local methods included Niblack, Bernsen, Sauvola, and Bradley-Roth algorithms. Artificial uneven illumination was introduced to test local adaptive thresholds. Results showed significant differences in porosity values across methods. Otsu, region growing, and K-means clustering excelled under uniform illumination, while Sauvola and Bradley-Roth performed better with uneven illumination. Comparison with X-ray computed tomography (XCT) revealed slightly lower porosity values (2.55 %) than optimized methods (2.73–2.79 %) due to XCT's lower resolution excluding smaller pores. While XCT offers finer pore detection, it limits sample volume and underestimates porosity due to spatial variation. Validation using artificial grayscale images with 5 % porosity confirmed that Otsu, Bradley-Roth, region growing, and Sauvola algorithms produced accurate results. Although tested on a single material system, these methods can be adapted to others with optimization. In conclusion, given XCT's high computational and time costs, this study highlights suitable image processing techniques as cost-effective alternatives for porosity analysis in polymer composites.

Additive manufacturing↗
DOE OSTI2026

Nondestructive ultrasonic characterization of a triple-weld-bead wire arc additively manufactured ER70S-6 S-curved wall

Understanding build-scale microstructural variation in wire arc additive manufacturing (WAAM) of low-carbon steels is essential for ensuring consistent structure–property relationships throughout large components. Conventional destructive characterization techniques, such as scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), are time-intensive and limited to localized regions, making comprehensive evaluation of large WAAM structures challenging. In this study, a nondestructive ultrasonic approach was employed to characterize a 252 mm tall ER70S-6 S-curved WAAM wall produced using a triple-bead deposition strategy. Optical and SEM analysis revealed a repeating dual-region microstructure consisting of uniform polygonal ferrite at melt pool centers and heterogeneous ferrite with coarse and fine grains near melt pool boundaries, attributed to cyclic thermal conditions. Longitudinal ultrasonic backscatter imaging was used to evaluate the continuity of this periodicity along the full build height. The ultrasonic response exhibited a consistent repeating pattern that correlated with the observed layer-wise microstructural variation. X-ray computed tomography confirmed the absence of detectable porosity, indicating that ultrasonic contrast is primarily governed by grain morphology. Overall, the results indicate that longitudinal backscatter ultrasound is a promising nondestructive characterization technique for validating microstructural variations along the s-curved WAAM wall, with significant potential for microstructure optimization and process control.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multipolymer Matrix

Additive manufacturing (AM) techniques to directly integrate phase change materials (PCMs) are of interest for efficient thermal energy storage (TES) architectures. Complex, high surface-to-volume ratio composites embedded with PCM can improve thermal management with reduced material waste for customizable device fabrication. Reducing feature sizes of TES-integrated heat exchangers using AM can increase heat transfer without thermal conductivity enhancement. Here, composite AM materials containing 60 wt% microencapsulated phase change materials (MEPCM) are fabricated using off-the-shelf printers at common speeds and resolutions. High MEPCM loading in filaments is achieved with powder extrusion using two polymers, thermoplastic-polyurethane (TPU) and polycaprolactone (PCL), that mediate flexibility and rigidity for effective extrusion and printing without filament fracture or buckling. Furthermore, with PCL and TPU at 20 wt% each and 60 wt% MEPCM (P 20 T 20 M 60 ), smooth, form-stable filaments are consistently printed. Powder-based extrusion displays negligible damaging effects on the MEPCM. Printed P 20 T 20 M 60 demonstrates 105 J/g of energy storage with no degradation through 250 thermal cycles, within 5% of the theoretical storage enthalpy. Combining PCL/TPU shows good interfacial adhesion between print layers and produces high surface area objects, like 15% gyroids, and dense, 100% infilled pucks. Prints are also scalable to a 900 cm 3 honeycomb heat exchanger with an estimated 9 Wh energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Additive Manufacturing with Cellulose-Based Composites: Materials, Modeling, and Applications

Recent advances in large-scale additive manufacturing (AM) with polymer-based composites have enabled efficient production of high-performance materials. Cellulose nanomaterials (CNMs) have emerged as bio-based feedstocks due to their exceptional strength and sustainability. However, challenges such as hornification and poor dispersion in polymer matrices still limit large-scale CNM–polymer composite manufacturing, requiring novel strategies. Here, this review outlines an approach starting with atomic-level simulations to link molecular composition to key parameters like bulk density, viscosity, and modulus. These simulations provide data for finite element analysis (FEA), which informs large-scale experiments and reduces the need for extensive trials. The strategy explores how atomic interactions impact the morphology, adhesion, and mechanical properties of CNM-based composites in AM processes. The review also discusses current developments in AM, along with predictions of mechanical and thermal properties for structural applications, packaging, flexible electronics, and hydrogel scaffolds. By integrating experimental findings with molecular dynamics (MD) simulations and finite element modeling (FEM), valuable insights for material design, process optimization, and performance enhancement in CNM-based AM are provided to address ongoing challenges.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Using Large-Scale Additive Manufacturing for Wind Turbine Blade Core Structures

This report describes the techno-economic potential of using additive manufacturing technologies to design large wind turbine blade structures. After considering all additive technologies, the authors identified large-scale, polymer-based, material extrusion as the three-dimensional (3D) printing technology best suited to meet modern wind turbine blade manufacturing costs, cycle times, and geometric scale. Due to the lower structural performance requirements and the opportunity to reduce resin uptake mass penalties within the blade, the core material within the sandwich composite sections of the wind turbine blade is established as a logical entry point into advanced wind turbine blade manufacturing.

17 WIND ENERGY↗
DOE OSTI2023

Exceptional thermal stability of additively manufactured CoCrFeMnNi high-entropy alloy with cellular dislocation structures

CoCrFeMnNi high-entropy alloy (HEA) was additively manufactured (AM) by laser powder-bed fusion (L-PBF). The AM CoCrFeMnNi has prominent cellular dislocation structures with a small number of Mn-rich oxides. The thermal stability of the AM CoCrFeMnNi was investigated by isochronal annealing treatment at various temperatures from 400 to 1300°C for 1h. Microstructural analysis shows slow dislocation recovery, retarded recrystallization process, and precipitation of additional Cr-Mn based oxides during thermal annealing, resulting in exceptional thermal stability and retained high hardness at elevated temperatures. Further, by thermodynamic calculations, a low stored energy of 1.31 MJ/m 3 and a high activation energy of 353 kJ/mol for recrystallization were estimated for the AM CoCrFeMnNi. The exceptional thermal stability of the AM CoCrFeMnNi HEA is mechanistically attributed to the low crystallographic misorientations across the dislocation cell walls, sluggish atomic diffusion, and the pinning effects of the oxide nanoprecipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Molecular dynamics simulations of radiation cascade evolution near cellular dislocation structures in additively manufactured stainless steels

The dislocation dense cellular structures observed in additively manufactured (AM) stainless steels can allow these materials to have enhanced strength and ductility compared to conventionally manufactured materials. Effective design of radiation resistant materials often necessitates creating microstructures containing of a high density of dislocations that act as sinks for radiation induced defects. This work uses molecular dynamics simulations to study the impact of pre-existing defects on radiation damage in stainless steel 316L fabricated by the laser powder bed fusion process. The evolution of synthetically generated dislocations in a crystal system in response to multiple radiation collision cascades suggest that dislocation dense regions reduce the probability of surviving point defects forming clusters. This finding seems to result from the dislocation cores’ ability to absorb point defects, thereby limiting the formation of clusters during the recombination phase. However, after successive cascades, the ability of the dislocation entanglement to prevent defect formation is diminished and defect cluster formation trends to an equilibrium. Accordingly, it is hypothesized that in an experimental setting the dislocation cells will initially act as neutral sinks for point defects, potentially delaying the onset of radiation damage effects; but, these structures will be degraded due to radiation-enhanced diffusion and lose their effectiveness at doses above 1.5–2 displacements per atom. Nevertheless, the ability to produce complex and feature-specific microstructures suggests promise for the design of radiation tolerant materials using AM methods.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Localized orientation gradients in additively manufactured stainless steel 316H structures

The high solidification rates during additive manufacturing cause highly localized thermal and strain gradients. The effect of these gradients on the evolution of local orientation misorientations within a grain is not well understood. In this study, stainless steel 316H parts were fabricated via laser powder bed fusion using three different energy densities: 43, 71, and 135 J/mm 3 . Electron backscatter diffraction showed that the maximum misorientations of the grains can be up to 25° along the build direction. Misorientation gradients (RM g ) within grains are process-dependent and can change from 0.036°/μm to 0.015°/μm with increased volumetric energy densities. In conclusion, the characterized misorientation gradients are an indication of the level of dislocations and, to an extent, the plastic deformation resulting from the rapid solidification during laser powder bed fusion.

316H↗
DOE OSTI2024

Clarifying the formation of equiaxed grains and microstructural refinement in the additive manufacturing of Ti-Cu

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

36 MATERIALS SCIENCE↗