Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “estimation methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Effect of counting and tracking on verbal and production methods of time estimation

The effects of time estimation technique and task condition on the production and verbal estimation of time intervals ranging from 5 to 14 sec were investigated. The duration of time intervals during each task condition pretracking, tracking (subject performed a one-axis tracking), and posttracking was estimated by the subjects. The ratio of the subject's time estimate to actual interval length was computed for each trial. Productions were typically longer than verbal estimates of the same duration and produced durations were typically too long whereas verbal estimates were too short relative to the correct duration. A significant interaction was found between counting technique and tracking condition for both estimation methods. A significant effect could be attributed to the addition of a tracking task: produced durations increased in length, whereas verbal estimates decreased in length. The durations produced without counting were significantly less accurate and consistent with the addition of a tracking task. Verbal estimation mean accuracy, but not consistency, was adversely affected by the addition of a tracking task when the subjects were instructed not to count.

Bird, K. L.↗
NASA NTRS1989

An investigation of new methods for estimating parameter sensitivities

The method proposed for estimating sensitivity derivatives is based on the Recursive Quadratic Programming (RQP) method and in conjunction a differencing formula to produce estimates of the sensitivities. This method is compared to existing methods and is shown to be very competitive in terms of the number of function evaluations required. In terms of accuracy, the method is shown to be equivalent to a modified version of the Kuhn-Tucker method, where the Hessian of the Lagrangian is estimated using the BFS method employed by the RQP algorithm. Initial testing on a test set with known sensitivities demonstrates that the method can accurately calculate the parameter sensitivity.

Beltracchi, Todd J.↗
NASA NTRS1984

Method to estimate drag coefficient at the air/ice interface over drifting open pack ice from remotely sensed data

A knowledge in near real time, of the surface drag coefficient for drifting pack ice is vital for predicting its motions. And since this is not routinely available from measurements it must be replaced by estimates. Hence, a method for estimating this variable, as well as the drag coefficient at the water/ice interface and the ice thickness, for drifting open pack ice was developed. These estimates were derived from three-day sequences of LANDSAT-1 MSS images and surface weather charts and from the observed minima and maxima of these variables. The method was tested with four data sets in the southeastern Beaufort sea. Acceptable results were obtained for three data sets. Routine application of the method depends on the availability of data from an all-weather air or spaceborne remote sensing system, producing images with high geometric fidelity and high resolution.

Feldman, U.↗
NASA NTRS1986

Helicopter rotor and engine sizing for preliminary performance estimation

Methods are presented for estimating some of the more fundamental design variables of single-rotor helicopters (tip speed, blade area, disk loading, and installed power) based on design requirements (speed, weight, fuselage drag, and design hover ceiling). The well-known constraints of advancing-blade compressibility and retreating-blade stall are incorporated into the estimation process, based on an empirical interpretation of rotor performance data from large-scale wind-tunnel tests. Engine performance data are presented and correlated with a simple model usable for preliminary design. When approximate results are required quickly, these methods may be more convenient to use and provide more insight than large digital computer programs.

Talbot, P. D.↗
NASA NTRS1985

A method for estimating soil moisture availability

A method for estimating values of soil moisture based on measurements of infrared surface temperature is discussed. A central element in the method is a boundary layer model. Although it has been shown that soil moistures determined by this method using satellite measurements do correspond in a coarse fashion to the antecedent precipitation, the accuracy and exact physical interpretation (with respect to ground water amounts) are not well known. This area of ignorance, which currently impedes the practical application of the method to problems in hydrology, meteorology and agriculture, is largely due to the absence of corresponding surface measurements. Preliminary field measurements made over France have led to the development of a promising vegetation formulation (Taconet et al., 1985), which has been incorporated in the model. It is necessary, however, to test the vegetation component, and the entire method, over a wide variety of surface conditions and crop canopies.

Carlson, T. N.↗
NASA NTRS1948

An Analytical Method of Estimating Turbine Performance

A method is developed by which the performance of a turbine over a range of operating conditions can be analytically estimated from the blade angles and flow areas. In order to use the method, certain coefficients that determine the weight flow and friction losses must be approximated. The method is used to calculate the performance of the single-stage turbine of a commercial aircraft gas-turbine engine and the calculated performance is compared with the performance indicated by experimental data. For the turbine of the typical example, the assumed pressure losses and turning angles give a calculated performance that represents the trends of the experimental performance with reasonable accuracy. The exact agreement between analytical performance and experimental performance is contingent upon the proper selection of the blading-loss parameter. A variation of blading-loss parameter from 0.3 to 0.5 includes most of the experimental data from the turbine investigated.

Kochendorfer, Fred D↗
NASA NTRS1949

An analytical method of estimating turbine performance

A method is developed by which the performance of a turbine over a range of operating conditions can be analytically estimated from the blade angles and flow areas. In order to use the method, certain coefficients that determine the weight flow and the friction losses must be approximated. The method is used to calculate the performance of the single-stage turbine of a commercial aircraft gas-turbine engine and the calculated performance is compared with the performance indicated by experimental data. For the turbine of the typical example, the assumed pressure losses and the tuning angles give a calculated performance that represents the trends of the experimental performance with reasonable accuracy. The exact agreement between analytical performance and experimental performance is contingent upon the proper selection of a blading-loss parameter.

Kochendorfer, Fred D↗
NASA NTRS1980

Maximum likelihood method for estimating airplane stability and control parameters from flight data in frequency domain

A frequency domain maximum likelihood method is developed for the estimation of airplane stability and control parameters from measured data. The model of an airplane is represented by a discrete-type steady state Kalman filter with time variables replaced by their Fourier series expansions. The likelihood function of innovations is formulated, and by its maximization with respect to unknown parameters the estimation algorithm is obtained. This algorithm is then simplified to the output error estimation method with the data in the form of transformed time histories, frequency response curves, or spectral and cross-spectral densities. The development is followed by a discussion on the equivalence of the cost function in the time and frequency domains, and on advantages and disadvantages of the frequency domain approach. The algorithm developed is applied in four examples to the estimation of longitudinal parameters of a general aviation airplane using computer generated and measured data in turbulent and still air. The cost functions in the time and frequency domains are shown to be equivalent; therefore, both approaches are complementary and not contradictory. Despite some computational advantages of parameter estimation in the frequency domain, this approach is limited to linear equations of motion with constant coefficients.

Klein, V.↗
NASA NTRS2012

Identification of Time-Varying Pilot Control Behavior in Multi-Axis Control Tasks

Recent developments in fly-by-wire control architectures for rotorcraft have introduced new interest in the identification of time-varying pilot control behavior in multi-axis control tasks. In this paper a maximum likelihood estimation method is used to estimate the parameters of a pilot model with time-dependent sigmoid functions to characterize time-varying human control behavior. An experiment was performed by 9 general aviation pilots who had to perform a simultaneous roll and pitch control task with time-varying aircraft dynamics. In 8 different conditions, the axis containing the time-varying dynamics and the growth factor of the dynamics were varied, allowing for an analysis of the performance of the estimation method when estimating time-dependent parameter functions. In addition, a detailed analysis of pilots adaptation to the time-varying aircraft dynamics in both the roll and pitch axes could be performed. Pilot control behavior in both axes was significantly affected by the time-varying aircraft dynamics in roll and pitch, and by the growth factor. The main effect was found in the axis that contained the time-varying dynamics. However, pilot control behavior also changed over time in the axis not containing the time-varying aircraft dynamics. This indicates that some cross coupling exists in the perception and control processes between the roll and pitch axes.

Zaal, Peter M. T.↗
NASA NTRS1971

Comparison of several methods for estimating low speed stability derivatives

Methods presented in five different publications have been used to estimate the low-speed stability derivatives of two unpowered airplane configurations. One configuration had unswept lifting surfaces, the other configuration was the D-558-II swept-wing research airplane. The results of the computations were compared with each other, with existing wind-tunnel data, and with flight-test data for the D-558-II configuration to assess the relative merits of the methods for estimating derivatives. The results of the study indicated that, in general, for low subsonic speeds, no one text appeared consistently better for estimating all derivatives.

Fletcher, H. S.↗
NASA NTRS1982

A method to estimate weight and dimensions of small aircraft propulsion gas turbine engines: User's guide

The weight and major envelope dimensions of small aircraft propulsion gas turbine engines are estimated. The computerized method, called WATE-S (Weight Analysis of Turbine Engines-Small) is a derivative of the WATE-2 computer code. WATE-S determines the weight of each major component in the engine including compressors, burners, turbines, heat exchangers, nozzles, propellers, and accessories. A preliminary design approach is used where the stress levels, maximum pressures and temperatures, material properties, geometry, stage loading, hub/tip radius ratio, and mechanical overspeed are used to determine the component weights and dimensions. The accuracy of the method is generally better than + or - 10 percent as verified by analysis of four small aircraft propulsion gas turbine engines.

Hale, P. L.↗
NASA NTRS2006

Method of Estimating Continuous Cooling Transformation Curves of Glasses

A method is proposed for estimating the critical cooling rate and continuous cooling transformation (CCT) curve from isothermal TTT data of glasses. The critical cooling rates and CCT curves for a group of lithium disilicate glasses containing different amounts of Pt as nucleating agent estimated through this method are compared with the experimentally measured values. By analysis of the experimental and calculated data of the lithium disilicate glasses, a simple relationship between the crystallized amount in the glasses during continuous cooling, X, and the temperature of undercooling, (Delta)T, was found to be X = AR(sup-4)exp(B (Delta)T), where (Delta)T is the temperature difference between the theoretical melting point of the glass composition and the temperature in discussion, R is the cooling rate, and A and B are constants. The relation between the amount of crystallisation during continuous cooling and isothermal hold can be expressed as (X(sub cT)/X(sub iT) = (4/B)(sup 4) (Delta)T(sup -4), where X(sub cT) stands for the crystallised amount in a glass during continuous cooling for a time t when the temperature comes to T, and X(sub iT) is the crystallised amount during isothermal hold at temperature T for a time t.

Zhu, Dongmei↗
DOE OSTI2026

Forced Component Estimation Statistical Method Intercomparison Project (ForceSMIP)

Anthropogenic climate change is unfolding rapidly, yet its regional manifestation can be obscured by internal variability. A primary goal of climate science is to identify the externally forced climate response from among the noise of internal variability. Separating the forced response from internal variability can be addressed in climate models by using a large ensemble to average over different possible realizations of internal variability. However, with only one realization of the real world, it is a major challenge to isolate the forced response directly in observations. In the Forced Component Estimation Statistical Method Intercomparison Project (ForceSMIP), contributors used existing and newly developed statistical and machine learning methods to estimate the forced response over 1950–2022 within individual realizations of the climate system. Participants used neural networks, linear inverse models, fingerprinting methods, and low-frequency component analysis, among other approaches. These methods were trained using large ensembles from multiple climate models and then applied to observations. Here, we evaluate method performance within large ensembles and investigate the estimates of the forced response in observations. Our results show that many different types of methods are skillful for estimating the forced response in climate models, though the relative skill of individual methods varies depending on the variable and evaluation metric. Methods with comparable skill in models can give a wide range of estimates of the forced response pattern in observations, illustrating the epistemic uncertainty in forced response estimates. ForceSMIP gives new insights into the forced response in observations, its uncertainty, and methods for its estimation.

Climate attribution↗
NASA NTRS1974

A method for estimating both the solubility parameters and molar volumes of liquids

Development of an indirect method of estimating the solubility parameter of high molecular weight polymers. The proposed method of estimating the solubility parameter, like Small's method, is based on group additive constants, but is believed to be superior to Small's method for two reasons: (1) the contribution of a much larger number of functional groups have been evaluated, and (2) the method requires only a knowledge of structural formula of the compound.

Fedors, R. F.↗
DOE OSTI2024

Probing Signal-Based Inertia and Frequency Response Estimation for Power Systems With High Levels of Inverter-Based Resources

Power system inertia is the inherent capability of a power system to resist changes in its frequency during disturbances. Real-time inertia estimation technology has become more important due to the low-inertia issues caused by the increasing integration levels of inverter-based resources (IBRs) from renewable energy; however, existing inertia estimation methods hardly consider multiple frequency response controls that act within the same time frame as conventional inertial response, thus making measured inertia values vary under different testing conditions. To resolve this issue, this paper proposes a novel real-time estimation method to simultaneously estimate a power system's inertia constant and frequency response droop constant using a well-designed probing signal. First, we formulate the inertia and frequency response model of a power system with IBRs. Second, through the integration and manipulation of the developed model, we propose a multivariate linear regression-based estimation method that is resilient to measurement noise. Third, we design a probing signal that can be injected by IBRs to incite the required transients for estimation. Finally, we validate the proposed estimation method through comprehensive power-hardware-in-the-loop experiments using inverter hardware and a realistic island power system model. The results demonstrate that the proposed method can accurately estimate the inertia and droop value of the power system with grid-following IBRs and grid-forming IBRs with virtual synchronous machine control.

frequency response↗
DOE OSTI2024

Probing Signal-Based Inertia and Frequency Response Estimation for Power Systems with High Penetration of Inverter-Based Resources: Preprint

Power system inertia is the inherent capability of a power system to resist changes in its frequency during disturbances. Real-time inertia estimation technology has become more important due to the low-inertia issues caused by the increasing integration levels of inverter-based resources (IBRs) from renewable energy; however, existing inertia estimation methods hardly consider multiple frequency response controls that act within the same time frame as conventional inertial response, thus making measured inertia values vary under different testing conditions. To resolve this issue, this paper proposes a novel real-time estimation method to simultaneously estimate a power system's inertia constant and frequency response droop constant using a well-designed probing signal. First, we formulate the inertia and frequency response model of a power system with IBRs. Second, through the integration and manipulation of the developed model, we propose a multivariate linear regression- based estimation method that is resilient to measurement noise. Third, we design a probing signal that can be injected by IBRs to incite the required transients for estimation. Finally, we validate the proposed estimation method through comprehensive power- hardware-in-the-loop experiments using inverter hardware and a realistic island power system model. The results demonstrate that the proposed method can accurately estimate the inertia and droop value of the power system with grid-following IBRs and grid-forming IBRs with virtual synchronous machine control.

frequency response↗