Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wetness fraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

One-step Tape Casting of Composites via Slurry on Fiber

A process by which metal matrix composites can be made was presented. The process involves putting a powder slurry on fibers to make a precursor green tape. These green tapes are cut, stacked and hot pressed to form the fully dense composite. A computer program was presented which enables complete quantification and control of the process. Once some easily obtained properties of the slurry and its behavior are determined (such as the shrinkage from the wet to green state, and the density of the green tape) modification of the fiber spacing and blade height give the maker precise control of fiber volume fraction, and fiber architecture in the composite. The process was shown to be accurate and flexible through the production of a wide variety of volume fraction fiber composites made from a wide variety of fibers and powders. The most time consuming step of the tape casting process (other than hot pressing) was winding the fiber on the drum. The tape casting techniques developed resulted in high quality metal matrix composites, with ultimate tensile strength in the range of 215 ksi (1477 MPa), a strain at failure of 1.15 percent, and in fatigue at room temperature 0 to 120 ksi, n = 0.3 Hz, a 4-ply Ti-24Al-11Nb/SCS-6, 32 vol% fiber tape cast composite lasted 202,205 cycles with a maximum strain on the 100th cycle of 0.43 percent.

deGroh, Henry C., III↗
NASA NTRS2001

The Potential of Using Landsat 7 Data for the Classification of Sea Ice Surface Conditions During Summer

During spring and summer, the Surface of the Arctic sea ice cover undergoes rapid changes that greatly affect the surface albedo and significantly impact the further decay of the sea ice. These changes are primarily the development of a wet snow cover and the development of melt ponds. As melt pond diameters generally do not exceed a couple of meters, the spatial resolutions of sensors like AVHRR and MODIS are too coarse for their identification. Landsat 7, on the other hand, has a spatial resolution of 30 m (15 m for the pan-chromatic band). The different wavelengths (bands) from blue to near-infrared offer the potential to distinguish among different surface conditions. Landsat 7 data for the Baffin Bay region for June 2000 have been analyzed. The analysis shows that different surface conditions, such as wet snow and meltponded areas, have different signatures in the individual Landsat bands. Consistent with in-situ albedo measurements, melt ponds show up as blueish whereas dry and wet ice have a white to gray appearance in the Landsat true-color image. These spectral differences enable the distinction of melt ponds. The melt pond fraction for the scene studied in this paper was 37%.

Markus, Thorsten↗
DOE OSTI2024

Molecular beam scattering of ammonia from a dodecane flat liquid jet

The evaporation and scattering of ND 3 from a dodecane flat liquid jet are investigated and the results are compared with previous studies on molecular beam scattering from liquid surfaces. Evaporation is well-described by a Maxwell–Boltzmann flux distribution with a cos θ angular distribution at the liquid temperature. Scattering experiments at E i = 28.8 kJ mol -1 over a range of deflection angles show evidence for impulsive scattering and thermal desorption. Further, at a deflection angle of 90°, the thermal desorption fraction is 0.49, which is higher than that of other molecules previously scattered from dodecane and consistent with work performed on NH 3 scattering from a squalane-wetted wheel. ND 3 scattering from dodecane results in super-specular scattering, as seen in previous experiments on dodecane. The impulsive scattering channel is fitted to a “soft-sphere” model, yielding an effective surface mass of 55 amu and an internal excitation of 5.08 kJ mol -1 . Overall, impulsively scattered ND 3 behaves similarly to other small molecules scattered from dodecane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1983

An application of model testing for the study of rocket exhaust cloud properties

The application of the 6.4-percent Shuttle Model Test Facility to the study of the Shuttle exhaust cloud properties is discussed with emphasis on the properties related to the production of the deposition (submillimeter drops composed of an acidic liquid and alumina solids) which occurs with each launch. An analysis of test data suggests that the major fraction of the liquid in the deposition is produced directly through the interaction between the exhaust and the deluge water spray and then modified by rapid scavenging of wet acidic aluminum oxide particles. Based on this conclusion, the possibility arises that the acid in the deposition can be neutralized by addition of a base to the deluge water. Current work with the 6.4-percent model is directed toward verification of this hypothesis.

Anderson, B. J.↗
NASA NTRS1993

New technique for oil backstreaming contamination measurements

Due to the large size and the number of diffusion pumps, space simulation chambers cannot be easily calibrated by the usual test dome method for measuring backstreaming from oil diffusion pumps. In addition, location dependent contamination may be an important parameter of the test. The backstreaming contamination in the Space Power Facility (SPF) near Sandusky, Ohio, the largest space simulation vacuum test chamber in the U.S.A. was measured. Small size clean silicon wafers as contamination sensors placed at all desired measurement sites were used. The facility used diffusion pumps with DC 705 oil. The thickness of the contamination oil film was measured using ellipsometry. Since the oil did not wet uniformly the silicon substrate, two analysis models were developed to measure the oil film: continuous, homogeneous film and islands of oil with the islands varying in coverage fraction and height. In both cases, the contamination film refractive index was assumed to be that of DC 705. The second model improved the ellipsometric analysis quality parameter by up to two orders of magnitude, especially for the low coverage cases. Comparison of the two models for our case shows that the continuous film model overestimates the oil volume by less than 50 percent. Absolute numbers for backstreaming are in good agreement with published results for diffusion pumps. Good agreement was also found between the ellipsometric results and measurements done by x ray photoelectron spectroscopy (XPS) and by scanning electron microscopy (SEM) on samples exposed to the same vacuum runs.

Alterovitz, S. A.↗
NASA NTRS1989

Energy management and recovery

Energy management is treated by first exploring the energy requirements for a cryogenic tunnel. The requirement is defined as a function of Mach number, Reynolds number, temperature, and tunnel size. A simple program and correlation is described which allow calculation of the energy required. Usage of energy is also addressed in terms of tunnel control and research operation. The potential of a new wet expander is outlined in terms of cost saved by reliquefying a portion of the exhaust. The expander is described as a potentially more efficient way of recovering a fraction of the cold nitrogen gas normally exhausted to the atmosphere from a cryogenic tunnel. The role of tunnel insulation systems is explored in terms of requirements, safety, cost, maintenance, and efficiency. A detailed description of two external insulation systems is given. One is a rigid foam with a fiber glass and epoxy shell. The other is composed of glass fiber mats with a flexible outer vapor barrier; this system is nitrogen purged. The two systems are compared with the purged system being judged superior.

Lawing, Pierce L.↗
NASA NTRS1991

A new technique for oil backstreaming contamination measurements

Due to the large size and the number of diffusion pumps, space simulation chambers cannot be easily calibrated by the usual test dome method for measuring backstreaming from oil diffusion pumps. In addition, location dependent contamination may be an important parameter of the test. The backstreaming contamination was measured in the Space Power Facility (SPF) near Sandusky, OH, the largest space simulation vacuum test chamber in the U.S.. Small clean silicon wafers placed at all desired measurement sites were used as contamination sensors. The facility used diffusion pumps with DC 705 oil. The thickness of the contamination oil film was measured using ellipsometry. Since the oil did not wet the silicon substrate uniformly, two analysis models were developed to measure the oil film: (1) continuous, homogeneous film; and (2) islands of oil with the islands varying in coverage fraction and height. In both cases, the contamination film refractive index was assumed to be that of DC 705. The second model improved the ellipsometric analysis quality parameter by up to two orders of magnitude, especially for the low coverage cases. Comparison of the two models shows that the continuous film model overestimates the oil volume by less than 50 percent. Absolute numbers for backstreaming are in good agreement with published results for diffusion pumps. Good agreement was also found between the ellipsometric results and measurements done by x-ray photoelectron spectroscopy (XPS) and by scanning electron microscopy (SEM) on examples exposed to the same vacuum runs.

Alterovitz, S. A.↗
NASA NTRS2001

Dependence of Aerosol Light Absorption and Single-Scattering Albedo On Ambient Relative Humidity for Sulfate Aerosols with Black Carbon Cores

Atmospheric aerosols frequently contain hygroscopic sulfate species and black carbon (soot) inclusions. In this paper we report results of a modeling study to determine the change in aerosol absorption due to increases in ambient relative humidity (RH), for three common sulfate species, assuming that the soot mass fraction is present as a single concentric core within each particle. Because of the lack of detailed knowledge about various input parameters to models describing internally mixed aerosol particle optics, we focus on results that were aimed at determining the maximum effect that particle humidification may have on aerosol light absorption. In the wavelength range from 450 to 750 nm, maximum absorption humidification factors (ratio of wet to 'dry=30% RH' absorption) for single aerosol particles are found to be as large as 1.75 when the RH changes from 30 to 99.5%. Upon lesser humidification from 30 to 80% RH, absorption humidification for single particles is only as much as 1.2, even for the most favorable combination of initial ('dry') soot mass fraction and particle size. Integrated over monomodal lognormal particle size distributions, maximum absorption humidification factors range between 1.07 and 1.15 for humidification from 30 to 80% and between 1.1 and 1.35 for humidification from 30 to 95% RH for all species considered. The largest humidification factors at a wavelength of 450 nm are obtained for 'dry' particle size distributions that peak at a radius of 0.05 microns, while the absorption humidification factors at 700 nm are largest for 'dry' size distributions that are dominated by particles in the radius range of 0.06 to 0.08 microns. Single-scattering albedo estimates at ambient conditions are often based on absorption measurements at low RH (approx. 30%) and the assumption that aerosol absorption does not change upon humidification (i.e., absorption humidification equal to unity). Our modeling study suggests that this assumption alone can introduce absolute errors in estimates of the midvisible single-scattering albedo of up to 0.05 for realistic dry particle size distributions. Our study also indicates that this error increases with increasing wavelength. The potential errors in aerosol single-scattering albedo derived here are comparable in magnitude and in addition to uncertainties in single-scattering albedo estimates that are based on measurements of aerosol light absorption and scattering.

Redemann, Jens↗
NASA NTRS1975

Series solution for the planar asymmetric blunt-body problem

Accurate semianalytic solutions to the inverse blunt-body problem have been obtained using a method of series expansion. Rational fractions are employed for series summation and analytic continuation. Angles of incidence up to 30 deg and Mach numbers as low as 2 have been considered. The maximum-entropy streamline will not wet the body surface in asymmetric flow. It may pass either above or below the stagnation streamline. Limit lines appear in the supersonic portion of the flow field, both in the shock layer and in its upstream analytic continuation.

Schwartz, L. W.↗
NASA NTRS2002

Discovery of coesite and shocked quartz associated with the upper Eocene cpx spherule layer

At least two major impact ejecta layers have been discovered in upper Eocene strata. The upper layer is the North American microtektite layer. lt consists tektite fragments, microtektites, and shocked mineral grains (e.g., quartz and feldspar with multiple sets of PDFs, coesite and reidite (a high-pressure polymorph of zircon)). The slightly older layer contains clinopyroxene-bearing (cpx) spherules and microtektites associated with an Ir anomaly. The North American tektite layer may be derived from the Chesapeake Bay impact structure, and the cpx spherule layer may from the Popigai impact crater. A cpx spherule layer associated with a positive Ir anomaly was recently found at ODP Site 709, western Indian Ocean. A large sample (Hole 709C, core 31, section 4, 145-150 cm), originally used for a study of interstitial water by shipboard scientists, was acquired for the purpose of recovering a large number of spherules for various petrographic and geochemical studies. A split of the sample (50.35 g) was disaggregated and wet-sieved. More than 17,000 cpx spherules and several hundred microtektites (larger than 125 microns) were recovered from the sample. Rare white opaque grains were observed in the 125-250 micron size fraction after removal of the carbonate component using dilute HCI. Seven of the white opaque grains were X-rayed using a Gandolfi camera and six were found to be coesite (probably mixed with lechatelierite). Eighty translucent colorless grains from the 63-125 micron size fraction were studied with a petrographic microscope. Four of the grains exhibit one to two sets of planar deformation features (PDFs). The only other possible known occurrence of shocked minerals associated with the cpx spherule layer is at Massignano, Italy, where pancake-shaped clay spherules (thought to be diagenetically altered cpx spherules are associated with a positive Ir anomaly and Ni- rich spinel crystals. Shocked quartz grains with multiple sets of PDFs also occur at this site. Until now, unmelted impact ejecta have not been found associated with the cpx spherules at any of the other 20 sites around the world and this is the first time that coesite has been found associated with the cpx spherule layer. The discovery of coesite and shocked quartz associated with the cpx spherules at Site 709 in Indian Ocean is further evidence for the impact origin of the cpx spherule layer. We hope that future discovery of other unmelted minerals from this sample may provide materials to establish constraints on the provenance of this late Eocene ejecta.

Liu, S.↗
NASA NTRS2003

Constraints on the Composition and Petrogenesis of the Martian Crust

Spectral interpretation that silicic rocks are widespread on Mars implies that Earth's differentiated crust is not unique. Evaluation of observations bearing on the composition of the Martian crust (Martian meteorite petrology and a possible crustal assimilant, analysis of Mars Pathfinder rocks, composition of Martian fines, interpretation of spacecraft thermal emission spectra, and inferred crustal densities) indicates that the crust can be either basalt plus andesite or basalt plus weathering products. New calculated chemical compositions for Thermal Emission Spectrometer (TES) global surface units indicate that surface type 1 has basaltic andesite composition and surface type 2 has the composition of andesite. If these materials represent volcanic rocks, their calc-alkaline compositions on a FeO*/MgO versus silica diagram suggest formation by hydrous melting and fractional crystallization. On Earth, this petrogenesis requires subduction, and it may suggest an early period of plate tectonics on Mars. However, anorogenic production of andesite might have been possible if the primitive Martian mantle was wet. Alternatively, chemical weathering diagrams suggest that surface type 2 materials could have formed by partial weathering of surface type 1 rocks, leading to depletion in soluble cations and mobility of silica. A weathered crust model is consistent with the occurrence of surface type 2 materials as sediments in a depocenter and with the alpha proton X-ray spectrometer (APXS) analysis of excess oxygen suggesting weathering rinds on Pathfinder rocks. If surface type 1 materials are also weathered or mixed with weathered materials, this might eliminate the need for hydrous melting, consistent with a relatively dry Martian mantle without tectonics.

McSween, Harry Y., Jr.↗
NASA NTRS2012

Potassium Stable Isotopic Compositions Measured by High-Resolution MC-ICP-MS

Potassium isotopic (K-41/K-39) compositions are notoriously difficult to measure. TIMS measurements are hindered by variable fractionation patterns throughout individual runs and too few isotopes to apply an internal spike method for instrumental mass fractionation corrections. Internal fractionation corrections via the K-40/K-39 ratio can provide precise values but assume identical K-40/K-39 ratios (e.g. 0.05% (1sigma) in [1]); this is appropriate in some cases (e.g. identifying excess K-41) but not others (e.g., determining mass fractionation effects and metrologically traceable isotopic abundances). SIMS analyses have yielded measurements with 0.25% precisions (1sigma) [2]. ICP-MS analyses are significantly affected by interferences from molecular species such as Ar-38H(+) and Ar-40H(+) and instrument mass bias. Single collector ICP-MS instruments in "cold plasma" mode have yielded uncertainties as low as 2% (1sigma, e.g. [3]). Although these precisions may be acceptable for some concentration determinations, they do not resolve isotopic variation in terrestrial materials. Here we present data from a series of measurements made on the Thermo Scientific NEPTUNE Plus multi-collector ICP-MS that demonstrate the ability to make K-41/K-39 ratio measurements with 0.07% precisions (1sigma). These data, collected on NIST K standards, indicate the potential for MC-ICP-MS measurements to look for K isotopic variations at the sub-permil level. The NEPTUNE Plus can sufficiently resolve 39K and 41K from the interfering 38ArH+ and 40ArH+ peaks in wet cold plasma and high-resolution mode. Measurements were made on small but flat, interference-free, plateaus (ca. 50 ppm by mass width for K-41). Although ICP-MS does not yield accurate K-41/K-39 values due to significant instrumental mass fractionation (ca. 6%), this bias can be sufficiently stable over the time required for several measurements so that relative K-41/K-39 values can be precisely determined via sample-standard bracketing. As cold plasma conditions can amplify matrix effects, experiments were conducted to test the matrix tolerance of measurements; the use of clean, matrix-matched samples and standards is critical. Limitations of the cold-plasma high-resolution MC-ICP-MS methodology with respect to matrix tolerance are discussed and compared with the limitations of TIMS methodologies.

Morgan, Leah E.↗
NASA NTRS2009

Contribution of Soil Moisture Information to Streamflow Prediction in the Snowmelt Season: A Continental-Scale Analysis

In areas dominated by winter snowcover, the prediction of streamflow during the snowmelt season may benefit from three pieces of information: (i) the accurate prediction of weather variability (precipitation, etc.) leading up to and during the snowmelt season, (ii) estimates of the amount of snow present during the winter season, and (iii) estimates of the amount of soil moisture underlying the snowpack during the winter season. The importance of accurate meteorological predictions and wintertime snow estimates is obvious. The contribution of soil moisture to streamflow prediction is more subtle yet potentially very important. If the soil is dry below the snowpack, a significant fraction of the snowmelt may be lost to streamflow and potential reservoir storage, since it may infiltrate the soil instead for later evaporation. Such evaporative losses are presumably smaller if the soil below the snowpack is wet. In this paper, we use a state-of-the-art land surface model to quantify the contribution of wintertime snow and soil moisture information -- both together and separately -- to skill in forecasting springtime streamflow. We find that soil moisture information indeed contributes significantly to streamflow prediction skill.

Reichle, Rolf↗
NASA NTRS2018

Ice Crystal Icing Physics Study using a NACA 0012 Airfoil at the National Research Council of Canada's Research Altitude Test Facility

This paper presents results from a study of the fundamental physics of ice-crystal ice accretion using a NACA 0012 airfoil at the National Research Council of Canada (NRC) Research Altitude Test Facility in August 2017. These tests were a continuation of work which began in 2010 as part of a joint collaboration between NASA and NRC. The research seeks to generate icing conditions representative of those that occur inside a jet engine when ingesting ice crystals. In this test, an airfoil was exposed to mixed-phase icing conditions and the resulting ice accretions were recorded and analyzed. This paper details the specific objectives, procedures, and measurements which included the aero-thermal and cloud measurements. The objectives were built upon observations and hypothesis generated from several previous test campaigns regarding mixed-phase ice-crystal icing. The specific objectives included (A) ice accretions under different wet-bulb temperatures, (B) investigations of steady-state ice shapes previously reported in the literature, (C) total water content variations in search of a threshold for accretion, and (D) probe characterization related to measuring melt fraction which is important to characterize the mixed-phase condition. The resulting ice accretions and conditions leading to such accretions are intended to help extend NASA’s predictive ice-accretion codes to include conditions occurring in engine ice-crystal icing.

Icing↗
NASA NTRSDate not supplied

Impacts of aerosol size-dependent below-cloud scavenging on tropospheric aerosol in the NASA GEOS model

Wet deposition is the major sink for a suite of tropospheric aerosols, and thus largely affects the global distribution and lifetime of aerosols as well as the formation of clouds in the atmosphere. In this study, we implement the aerosol size-dependent below-cloud scavenging (BCS; washout) parameterization of Croft et al. (Atmos. Chem. Phys., 2009; hereafter referred to as C09) in the GOCART bulk aerosol scheme coupled with the NASA Goddard Earth Observing System (GEOS) model, and evaluate the simulated tropospheric aerosols against surface, airborne, and satellite observations. The current below-cloud scavenging in GOCART employs a first-order removal function with a constant scavenging coefficient that is independent of aerosol sizes and precipitation fluxes. The C09 BCS parameterization instead calculates aerosol below-cloud scavenging coefficients based on a size-dependent collision efficiency between aerosol particles and raindrops (or snow crystals). A look-up table of compiled collision efficiencies provides scavenging coefficients for sixty aerosol sizes and nine rain flux rates. We determine instantaneous coefficients according to the C09 BCS look-up table, precipitation fluxes, and a log-normal size distribution of aerosols. The implemented BCS parameterization tends to result in a large diversity of scavenging coefficient values with higher magnitudes, leading to more efficient scavenging. The model-simulated global mean tropospheric Pb-210 aerosol lifetime decreases from 7.4 days to 5.8 days. The separate consideration of rain and snow conditions in the scavenging coefficient lookup table leads to a bi-mode distribution of scavenging coefficients. These changes also cause increased mass fractions of smaller aerosols compared to the current simulation. We examine the impacts of the C09 BCS parameterization on the simulated aerosol vertical profiles, tropospheric lifetimes, and deposition fluxes through comparisons with NASA aircraft measurements (ATom), surface observations of aerosol concentrations (IMPROVE) and wet deposition fluxes (NADP and APQMP), and MODIS aerosol optical depth (AOD) retrievals.

Aerosols↗
DOE OSTI2024

Fully Recyclable CFRP Particles (CRADA 519)

The proposed resin-enhanced materials, which utilize fully recycled CFRP (carbon-fiber-reinforced polymer) particles, are enabled by PARC's proprietary Chemically Linked Particles Networks (13 granted patents and patent applications). PNNL and PARC have collaborated to develop manufacturing methods, such as vacuum-assisted wet compression molding and filament winding, for fabricating fiber-reinforced composites with the PARC matrix. PNNL has conducted various mechanical, physical, and thermal characterizations to compare their differences between the composites with baseline and PARC matrices. Those characterizations include density, void volume fraction, optical micrography, uniaxial tension, four-point bending/flexure, interlaminar shear, coefficient of thermal expansion, glass transition temperature, and curing kinetics.

36 MATERIALS SCIENCE↗
NASA NTRS1992

An experiment-based model for the petrogenesis of high-alumina basalts

To understand magmatism at convergent margins, one must know the origin of their characteristic plagioclase-rich high-alumina basalts (HABs). Wet melting experiments on basalts at 3 kilobars yielded high-alumina liquids and a coexisting mineral assemblage with plagioclase crystallization in these melts, while mafic minerals underwent limited crystallization or even resorption. These results suggest that hydrous HAB liquids, presumably formed by fractionation of a hydrous basalt at depth, precipitate voluminous plagioclase as pressure drops during ascent and eruption. Plagioclase accumulation is not necessarily required to explain the petrogenesis of plagioclase-rich HAB.

Beard, J. S.↗
DOE OSTI2024

Fe-rich X-ray amorphous material records past climate and persistence of water on Mars

X-ray amorphous material comprises 15-73 wt.% of sedimentary rocks and eolian sediments in Gale crater. This material is variably siliceous and iron rich but aluminum poor. The presence of volatiles is consistent with the existence of incipient weathering products. To better understand the implications of this material for past aqueous conditions on Mars, here we investigate X-ray amorphous material formation and longevity within terrestrial iron rich soils with varying ages and environmental conditions using bulk and selective dissolution methods, X-ray diffraction, and transmission electron microscopy. Results indicate that in situ aqueous alteration is required to concentrate iron into clay-size fraction material. Cooler climates promote the formation and persistence of X-ray amorphous material whereas warmer climates promote the formation of crystalline secondary phases. Iron rich X-ray amorphous material formation and persistence on Mars are therefore consistent with past cool and relatively wet environments followed by long-term cold and dry conditions.

54 ENVIRONMENTAL SCIENCES↗