SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This slide describes a set of techniques that generate high-voltage control signals of ion trap from low-voltage domain, at cryogenic temperature. With proposed solutions, a conversion between arbitrary signal ranges is achievable.
Spontaneously emitted radiation from excited atoms can be of principle importance in certain modes of electrical breakdown, especially positive streamers and some regimes of Townsend breakdown. The electrostatic particle-in-cell code Aleph utilizes the direct simulation Monte Carlo method to compute radiation transport. When there is strong radiation trapping, this approach is limited in that it must resolve the timescale associated with self-absorption. This renders many cases computationally intractable as sub-femtosecond time steps can be required to compute solutions for phenomena that occur over nanoseconds or microseconds. For two specific cases which exhibit strong radiation trapping, we find that spontaneous emissions having a frequency near the line center are inactive in the breakdown process and can be neglected. This enables larger time steps and a computational speedup of up to two orders of magnitude is observed. Some considerations for determining the validity of making such an approximation for Townsend breakdown problems and positive ionization wave problems are presented.
Chemical reactions in microscale compartments, such as aerosols and emulsions, can exhibit significantly faster reaction rates relative to macroscale containers. This enhancement in chemistry is often due to the elevated importance of surfaces as reaction vessels are reduced to picoliter volumes. While most studies have focused on the air-water interface of droplets, there are comparably fewer studies of reactions in micron-scale aqueous solutions encapsulated by oil. Here we investigate the condensation reaction of pyruvic acid (PA) to form zymonic acid (ZA) and water. Using microfluidics and optical trapping, chemical kinetics are measured in monodisperse micron-sized emulsion droplets in situ via Raman spectroscopy. Relative to a macroscopic bulk solution, which exhibits little to no reaction over many days, we find efficient production of ZA over the same time period. A kinetic model is developed to elucidate the role of the interface in accelerating the microdroplet reaction kinetics. After quantifying the surface partitioning of PA from interfacial tension measurements, the rate coefficient for the condensation reaction at the oil-water interface is determined to be 1.8 × 10-2 M-1 s-1. This rate coefficient is estimated to be 105 larger than the reaction rate in bulk aqueous solutions. Compared to previous studies of accelerated ZA formation at the air-water interface on nanodroplets, we find that the reaction at the oil-water interface is 20 times more efficient. Despite this difference, the overall ZA formation rate in emulsions is significantly slower than in the same-sized aerosols, which arises from the weaker partitioning of PA to the oil-aqueous relative to air-water interface. These results highlight the interplay between interfacial partitioning and reactivity in accelerating chemistry in microcompartments and provides new insights into how interfacial composition influences condensation reactions.
Abstract Polycrystalline perovskite film‐based X‐ray detector is an appealing technology for assembling large scale imager by printing methods. However, thick crystalline layer without trap and solvent residual is challenging to fabricate. Here, the authors report a solution method to produce high quality quasi‐2D perovskite crystalline layers and detectors that are suitable for X‐ray imaging. By introducing n ‐butylamine iodide into methylammonium lead iodide precursor and coating at elevated temperatures, compact and crystalline layers with exceptional uniformity are obtained on both rigid and flexible substrates. Photodiodes built with the quasi‐2D layers exhibit a low dark current and stable operation under constant electrical field over 96 h in dark, and over 15 h under X‐ray irradiation. The detector responds sensitively under X‐ray, delivering a high sensitivity of 1214 µC Gy air −1 cm −2 and a sensitivity gain is observed when operated under higher fields. Finally, high resolution images are demonstrated using a single pixel device that can resolve 80–200 µm features. This work paves the path for printable direct conversion X‐ray imager development.
Abstract. An unphysical checkerboard pattern is identified in E3SMv2 and E3SM-MMF that is detectable across a wide range of timescales, from instantaneous snapshots to multi-year averages. A detection method is developed to quantify characteristics of the checkerboard signal by cataloguing all possible configurations of the eight adjacent neighbors for each cell on the model's cubed sphere grid using daily mean data. The checkerboard pattern is only found in cloud-related quantities, such as precipitation and liquid water path. Instances of pure and partial checkerboard are found to occur more often in E3SMv2 and E3SM-MMF when compared to satellite data regridded to the model grid. Continuous periods of partial checkerboard state are found to be more persistent in both models compared to satellite data, with E3SM-MMF exhibiting more persistence than E3SMv2. The checkerboard signal in E3SMv2 is found to be a direct consequence of the recently added deep convective trigger condition based on dynamically generated CAPE (DCAPE). In E3SM-MMF the checkerboard signal is found to be associated with the “trapping” of cloud-scale fluctuations within the embedded cloud-resolving model. Solutions to remedy this issue are discussed.
Optical tweezers are a powerful tool for exploring physical properties of particles in various environments through analysis of their dynamics in a trapping potential. Analysis of the trapped particle's position is often done using interferometric back-focal-plane detection microscopy in which interference between the trapping laser and the light interacting with the trapped particle is projected on a quadrant photo-diode (QPD). The QPD measurements are almost universally the voltage ratios between the transverse components of the detector (left/right; up/down) that are calibrated to ascertain particle positions and orientations (i.e., rotation). In this paper, we demonstrate how measuring the diagonal ratio of the QPD allows tracking the spinning and orbital motion of optically trapped objects with enhanced sensitivity compared to the conventional transverse ratio and reveals additional information about particle dynamics. The diagonal ratio "balances" the signal from opposite sides of the QPD, allowing common mode noise reduction and increased measurement sensitivity of the rotating nanospheres at frequencies from below 200 Hz to above 15 kHz. We show that the variability in particle rotation rates is due to slight differences in the aspect ratio of the nanoparticles. We also measure in situ a gradual acceleration in the spinning frequency of trapped nanoparticles due to photothermal shedding of surface ligands and the resulting decrease of rotational friction in solution. The accelerating particles spin at rates exceeding 30 kHz and are eventually "optically printed" onto the glass coverslip on top of the liquid cell enclosure. The diagonal ratio is a simple, readily available, and powerful enabler for measuring rotational dynamics with a 5-fold sensitivity increase over conventional QPD measurements. This affords opportunities for controlling the orientational dynamics of trapped nanoparticles, which is crucial for various applications, including nanoscale mechanical motors.
Abstract Fission gas release within uranium dioxide nuclear fuel occurs as gas atoms diffuse through grains and arrive at grain boundary (GB) bubbles; these GB bubbles grow and interconnect with grain edge bubbles; and grain edge tunnels grow and connect to free surfaces. In this study, a hybrid multi-scale/multi-physics simulation approach is presented to investigate these mechanisms of fission gas release at the mesoscale. In this approach, fission gas production, diffusion, clustering to form intragranular bubbles, and re-solution within grains are included using spatially resolved cluster dynamics in the Xolotl code. GB migration and intergranular bubble growth and coalescence are included using the phase field method in the MARMOT code. This hybrid model couples Xolotl to MARMOT using the MultiApp and Transfer systems in the MOOSE framework, with Xolotl passing the arrival rate of gas atoms at GBs and intergranular bubble surfaces to MARMOT and MARMOT passing evolved GBs and bubble surface positions to Xolotl. The coupled approach performs well on the two-dimensional simulations performed in this work, producing similar results to the standard phase field model when Xolotl does not include fission gas clustering or re-solution. The hybrid model performs well computationally, with a negligible cost of coupling Xolotl and MARMOT and good parallel scalability. The hybrid model predicts that intragranular fission gas clustering and bubble formation results in up to 70% of the fission gas being trapped within grains, causing the increase in the intergranular bubble fraction to slow by a factor of six. Re-solution has a small impact on the fission gas behavior at 1800 K but it has a much larger impact at 1000 K, resulting in a twenty-times increase in the concentration of single gas atoms within grains. Due to the low diffusion rate, this increase in mobile gas atoms only results in a small acceleration in the growth of the intergranular bubble fraction. Finally, the hybrid model accounts for migrating GBs sweeping up gas atoms. This results in faster intergranular bubble growth with smaller initial grain sizes, since the additional GB migration results in more immobile gas clusters reaching GBs.
Reactive nitrogen species (RNS), along with reactive oxygen species (ROS), are significant products from radiolysis in solution. While much research has been focused on biological systems, these species are also important products in the autoradiolysis that occurs in nuclear waste. In this work, we determine the correlation between solution constituents, particularly nitrite, and radical products in highly alkaline solutions relevant to liquid waste. Because these radicals tend to be very short-lived, we employ spin trapping in conjunction with electron paramagnetic resonance (EPR) to detect them and quantify their production. Most spin traps do not function in these conditions (>1 M NaOH); however, nitroalkanes such as nitromethane will act as spin traps in their aci form, which is dominant at high pH. To restrict the products to those originating from nitrite, we use 280–480 nm UV light to generate radicals, avoiding products from the photolysis of water. Under these circumstances, nitric oxide, nitrite radicals, and hydroxyl radicals are detected, and the trends with the concentration of the constituents of the solutions are tracked. These include nitrite, nitrate, hydroxide, and carbonate. We find that, while the equilibrium shifts with increasing pH from hydroxyl radicals to the more slowly reacting oxide radicals, the production of nitrite radicals does not decrease.
The original version of this report described the development of a mathematical model for the estimation of the hydrogen composition of gas bubbles trapped in radioactive waste. The model described therein used a material balance approach to accurately incorporate the rates of hydrogen generation by several physical phenomena and scale the aforementioned rates in a manner that allows calculation of the final hydrogen composition. The proposed model accounted for the following physical phenomena: H 2 generation by primary radiolysis of water and salt solutions; H 2 generation by secondary radiolysis of formate and glycolate molecules in solution; Observation of negligible H 2 generation by thermolysis of formate at temperatures below 120 °C; H 2 generation by thermolysis of glycolate in caustic solutions; O 2 consumption by radiolysis and thermolysis of organic species. Additionally, the originally-proposed model conservatively excluded the following physical phenomena that are known to contribute slightly to the hydrogen composition in trapped gas bubbles: Equilibrium concentration of water vapor in trapped gas bubbles; Generation of N 2 O during radiolysis of nitrite solutions; Incomplete consumption of O 2 by organics. In this revision, the methodology for glycolate thermolysis has been improved to agree with recent findings published by Woodham and Martino. Furthermore, considerations for the thermolysis of organics other than glycolate have been made. In the case of non-glycolate organics, no evidence of non-flammable gas formation exists. Therefore, non-glycolate thermolysis is considered additive for conservatism.
Single-molecule fluorescence spectroscopy allows direct, real-time observation of dynamic photophysical changes in light harvesting complexes. The Anti-Brownian ELectrokinetic (ABEL) trap is one such single-molecule method with useful advantages. This approach is particularly well-suited to make detailed spectroscopic measurements of pigment-protein complexes in solution phase because it enables extended-duration single-molecule observation by counteracting Brownian motion. This Perspective summarizes recent contributions by the authors and others that have utilized the unique capabilities of the ABEL trap to advance our understanding of phycobiliproteins and the phycobilisome complex, the primary light-harvesting apparatus of cyanobacteria. Monitoring the rich spectroscopic data from these measurements, which include brightness, fluorescence lifetime, polarization, and emission spectra, among other measurable parameters, has provided direct characterization of pigments and energy transfer pathways in the phycobilisome, spanning scales from single pigments and monomeric phycobiliproteins to higher order oligomers and protein-protein interactions of the phycobilisome complex. Importantly, new photophysical states and photodynamics were observed to modulate the flow of energy through the phycobilisome and suggest a previously unknown complexity in phycobilisome light harvesting and energy transport with a possible link to photoadaptive or photoprotective functions in cyanobacteria. Here, beyond deepening our collective understanding of natural light-harvesting systems, these and future discoveries may serve as inspiration for engineering improved artificial light-harvesting technologies.
Balanced electron and hole transport properties are essential for various organic electrical/optoelectrical applications such as organic solar cells, complementary circuits, and light-emitting transistors. However, the electron transport in organic semiconductor lags far behind the hole side, making it with vital significance to seek the factors that limit the electron mobility. Here, the authors demonstrate that the π-conjugated solvents, as essential components in the widely-used solution processing techniques, can significantly suppress the electron transport if they are not properly removed and trapped as residuals. Single crystals of typical p-type materials exhibit a transition from p-type behavior to ambipolar conductance via reducing the amount of solvent residuals, and the same effect is confirmed by varied p-type materials and solvents. The highest electron mobility reaches 0.027 cm 2 V –1 s –1 and 0.029 cm 2 V –1 s –1 for 6,13-bis(triisopropylsilylethynyl)pentacene and 5,15-bis(triisopropylsilylethynyl)tetrabenzoporphyrin, respectively. Finally, this work discloses the non-negligible existence of solvent residuals even in high quality, long-range ordered organic single crystals, and further provides efficient strategies to harvest the n-type behaviors of organic semiconductor materials.
The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.
Metal halide perovskites have garnered a great deal of attention for their applications in photovoltaics, LEDs, and radiation detection. The ease of solution processing high-quality perovskite semiconductors with large absorption coefficients and tolerance to native defects is decidedly attractive. Additionally, the ability to precisely tune the band gap of halide perovskites through compositional alloying of the halide ion is of particular interest for a range of applications, especially for tandem solar cells. However, under steady state light irradiation, an initially homogeneous mixed halide perovskite (MHP) will form local domains that are rich in one halide ion (e.g., Br or I). This light-induced phase segregation in MHPs forms iodide-rich domains that act as charge carrier traps and lowers the efficiency of perovskite-based devices. Thus, phase segregation poses a serious challenge to the implementation of MHPs in real-world device settings. Interestingly, when a phase segregated MHP film is placed in the dark, entropic driving forces become dominant and the segregated perovskite remixes and returns to its initially homogeneous state. Several key mechanistic details of phase segregation have been elucidated over the years. However, there are still aspects of halide segregation that are not clear, and there is ongoing debate in the literature as to what are the key factors that contribute to the mechanism. This Account discusses recent results that point to the specific role of hole trapping in phase segregation. Interestingly, generation of holes through above-band-gap excitation or through electrochemical injection increases ion migration and leads to phase segregation. The thermodynamic and redox properties of halide perovskites provide a strong driving force for hole trapping and oxidation of iodide species in MHPs. However, mobile halide species within the perovskite lattice take time to migrate and generate halide-rich domains. When in contact with a nonpolar solvent, the migration of iodine species is further extended to expulsion of iodine from the perovskite film. Thus, the mobility of halides and their susceptibility to hole-induced oxidation play a crucial role in determining the long-term stability of metal halide perovskites. Strategies to gain kinetic control over ion migration to slow phase segregation are needed to overcome these hurdles and achieve stable mixed halide perovskites. Modification of the perovskite composition through introduction of different cations or halide ions, or introduction of low-dimensional perovskite phases may suppress phase segregation. Furthermore, in achieving stability and improving the efficiency of perovskite solar cells and light emitting devices with minimal impacts, suppression of segregation remains the key factor.
The quantum approximate optimization algorithm (QAOA) has the potential to approximately solve complex combinatorial optimization problems in polynomial time. However, current noisy quantum devices cannot solve large problems due to hardware constraints. In this work, we develop an algorithm that decomposes the QAOA input problem graph into a smaller problem and solves MaxCut using QAOA on the reduced graph. The algorithm requires a subroutine that can be classical or quantum—in this work, we implement the algorithm twice on each graph. One implementation uses the classical solver Gurobi in the subroutine and the other uses QAOA. We solve these reduced problems with QAOA. On average, the reduced problems require only approximately 1/10 of the number of vertices than the original MaxCut instances. Furthermore, the average approximation ratio of the original MaxCut problems is 0.75, while the approximation ratios of the decomposed graphs are on average of 0.96 for both Gurobi and QAOA. With this decomposition, we are able to measure optimal solutions for ten 100-vertex graphs by running single-layer QAOA circuits on the Quantinuum trapped-ion quantum computer H1-1, sampling each circuit only 500 times. This approach is best suited for sparse, particularly k-regular graphs, as k-regular graphs on n vertices can be decomposed into a graph with at most $\frac{nk}{k+1}$ vertices in polynomial time. Further reductions can be obtained with a potential trade-off in computational time. In conclusion, while this paper applies the decomposition method to the MaxCut problem, it can be applied to more general classes of combinatorial optimization problems.
The direct injection spark ignition (DISI) engine has received considerable attention due to its potential to increase the power density of traditional spark ignition engines while significantly improving fuel economy through lean, unthrottled combustion. However, the market introduction of DISI engines operated in a lean combustion mode is inhibited by their unsatisfactory emissions, especially during cold start conditions that make proper mixture formation more challenging. Ethanol-blended gasoline, now a widely used fuel, makes the cold start of a DISI engine more difficult, leading to higher HC and soot emissions because of the high latent heat of vaporization of ethanol relative to gasoline. This work investigated the impact of coolant temperature on the characteristics of combustion and emissions in a stratified-charge DISI engine fueled with an E30 fuel (i.e. 30% ethanol in gasoline), while the coolant temperature was alternated between four levels (45, 60, 75, and 90 °C) to simulate different conditions throughout the warm-up process. The experiments showed that the coolant temperature affected the post-spark inflammation time, as well as the speed, intensity, and stability of the combustion process in the engine. When the coolant temperature rose, the engine produced more NOX and less CO, PM and HC. In addition, high-speed direct photography was used to obtain crank-angle resolved images of fuel sprays and flames in the cylinder. As the coolant temperature rose, the liquid spray lengths became shorter, reducing the possibility of wall wetting, and reduced irradiance from soot particles also indicated less nonpremixed combustion. The in-cylinder imaging results are consistent with the observed combustion and emission characteristics and shed light on the underlying processes. Finally, some potential solutions to the emissions challenges faced here could be either raising in-cylinder temperatures by using trapped residuals or modifying the injection schedule, for example by increasing the number of injections or to inject later in the cycle into a higher-density environment.
This laboratory study was initiated to develop an improved technical understanding of the key controlling geochemical and physical processes of mobilizing residual Cr(VI) in Hanford sediments to provide increased effectiveness in soil flushing activities planned for Hanford 100 Areas. This was accomplished by (1) quantifying Cr mass, release rate, and surface phase changes as Cr is leached from different Hanford sediments; (2) maximizing Cr leaching during soil flushing by evaluating different leach solutions and leach strategies; and (3) minimizing leaching of remaining residual Cr after soil flushing ends. To quantify geochemical controls on Cr leaching from sediments, sequential liquid extractions were used to identify aqueous, adsorbed, and solid Cr surface phases (precipitates or Cr incorporated into other phases) before and after water-saturated and unsaturated leach experiments with pH 8 artificial groundwater and with other amendment solutions. Changes in the Cr release rate from sediments were also correlated to changes in Cr surface phases. During unsaturated infiltration, water advection occurs primarily through larger pores, with less movement through smaller grain layers leading to a slower release of Cr trapped in smaller pores next to smaller grains. To quantify these physical controls on Cr leaching from sediments, 10 ft high 1-D infiltration experiments were conducted at differing leach solution application rates, and Cr leaching during application and subsequent residual water flow was quantified. Qualitative 2-D experiments were also conducted to evaluate surfactant addition to increase flow in low-permeability zones. Cr-contaminated Hanford sediments from the 100-H, 100-K, 100-D, and 200 East Areas exhibited a wide variety of leach behavior from rapid release of a small amount of Cr to fast (i.e., minutes) and slow (i.e., hours or more) release of high Cr. Sediments with low labile Cr (< 0.2 µg/g) exhibited fast Cr release but less overall release, and most (>95%) leached from the sediments within a few pore volumes in water-saturated columns. With nearly no sorption of chromate, aqueous and sorbed Cr (as chromate) were released quickly from sediment within the first few pore volumes, resulting in high leach concentrations, fast initial Cr release rates, and changes in pre- and post-leach extractions. In contrast, sediments with high labile Cr (0.2 to 20 µg/g) exhibited a combination of fast and slow Cr release due to multiple Cr surface phases contributing to Cr release from the sediment at different rates with greater overall release. This resulted in elevated Cr effluent concentrations even after dozens of pore volumes were leached. In addition, the Cr release rate decreased with increasing time during leaching. A decrease in labile Cr (aqueous Cr, adsorbed Cr, pH 5 acetate dissolved precipitates) in post-leach extractions compared to pre-leach extractions showed initial aqueous and adsorbed Cr release, followed by dissolution of high-solubility precipitates such as CaCrO 4 (if present), then slow dissolution of calcite that may contain some chromate and possibly BaCrO 4 . The labile Cr in all sediments correlated well with the Cr release rate (r 2 = 0.81). Labile Cr also correlated well with the leached mass in water-saturated columns (r 2 = 0.98), and therefore can be used for prediction of potential removal with flushing applications.
Sunlight-induced halide segregation in (CH 3 NH 3 )Pb(Br x I 1−x ) 3 (1 > x > 0.2), which limits obtainable voltages from solar cells with these perovskite absorbers, reverses upon resting in the dark. However, sustained illumination at ca. 1 sun opens a new decomposition pathway, leading to irreversible I 2 loss in an open system. We conclusively show I 2 off-gassing from halide-segregated (CH 3 NH 3 )Pb(Br 0.75 I 0.25 ) 3 by trapping gaseous I 2 and tracking the electronic conductivity of the perovskite, which increases from electron-doping as iodides are oxidized to iodine. Importantly, we show that this reaction occurs across the perovskite-air solid–gas interface, without confounding effects from solvent or reactive solid interfaces. This characterization was conducted under a nitrogen atmosphere, avoiding vacuum- and oxygen-driven I 2 loss pathways. Consistent observations of I 2 loss upon light-soaking CsPb(Br 0.75 I 0.25 ) 3 films show that this reaction is intrinsic to the inorganic framework. We propose that the disruption of iodide-rich domains in the halide-segregated films through I 2 loss can masquerade as a light-induced healing or apparent remixing of the segregated film, when in fact it leads to irreversible decomposition. Although I 2 off-gassing is less likely in bromide-rich solid solutions, light-induced halide segregation brings the iodides into proximity and forms electronic states that are energetically poised to trap and accumulate holes, providing a driving force for I 2 loss. Thus, even bromide-rich mixed-halide perovskite absorbers will benefit from I 2 -impermeable encapsulation for long-term stability.
Understanding of the long-term stability of vitrified nuclear waste glass is critical to its safe storage, but knowledge gaps remain regarding the corrosion mechanism, especially with respect to surface alteration layers whose presence changes the observed corrosion rates. Here, we report the aqueous corrosion of a model boroaluminosilicate glass at ground water relevant pHs as investigated by vibrational spectroscopy to understand the network structure of the alteration layer that we hypothesize controls the corrosion rates. Both specular reflection infrared spectroscopy and infrared variable angle spectroscopic ellipsometry were used to elucidate details of the structure of the alteration layers formed at pH 7 and pH 9. After 2312 days, the thickness of the alteration layer is found to be ~2000 nm for corrosion at pH 7 and ~300 nm for corrosion at pH 9. Here, the interpretation of the vibrational spectra suggests that alteration layers formed at pH 7 and pH 9 both exhibit a porous network with "silica-like" structures, but with differences in the bond lengths and bond angles in the glass network. Moreover, the relative abundance of the hydrous species within the porous network appears to be dependent on pH. Additionally, the spectroscopic data suggest that the B and Ca trapped in the alteration layer during the secondary corrosion of the pH 9 pre-corroded sample in pH 3 solution are hydrated within the nano-porous layer and not bound to the silicate network. However, the precise chemical form remains to be determined. Based on these findings, we propose that the combination of the network structure of the alteration layer and the relative abundance of hydrous species within the alteration layer act to control the transport of ionic species dissolved from the reaction front to the aqueous solution outside the glass.