Results for “MAGNETIC INDUCTION” — Page 4

DOE OSTI2025

Si-Cr-Al-Mn Alloy for High Specific Resistivity

Laboratory material produced in budget period one met the target resistivity, mechanical and magnetic requirements for the Go/No-Go decision to move to industrial trials. The chosen chemistry settled on a high Cr strategy, with moderate Mn and Al additions, providing a good comprise on core loss and induction with minimal impact on mechanical properties, important to successful downstream processing. Industrial trials began in budget period two with the chosen chemistry, referred to as Alloy X. Difficulties occurred during initial hot rolling trials. Reheating the material using the standard NOES practice caused slab cracking from high thermal gradients in areas exposed to the roof burners, this was solved using a modified reheat practice. High Cr caused poor dynamic recrystallization during hot rolling, which was solved using a modified hot rolling practice. The high Cr content of the steel also caused poor decarburization during final annealing, which necessitated lowering the melt carbon aim for the final heat, together with a modified decarburization practice. Steel was finished to final thicknesses of 0.20 – 0.50 mm and evaluated for magnetic and mechanical properties. Although the target core loss for the 0.25 and 0.35 mm material was not achieved, significant reductions in high frequency core loss were measured, compared to equivalent commercially available material. Alloy X at 0.35 mm showed a 26 % and 23 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ M-19 (0.35 mm) commercially available NOES. At 0.25 mm, Alloy X showed a 23 % and a 26 % improvement at 400 HZ and 1000 Hz respectively, over Cliffs’ HF-10 (0.25 mm) commercially available NOES. The 0.25 mm product was chosen for motor efficiency evaluation. ORNL collaborated with Cleveland-Cliffs (CC) to build, assemble, and test two 5HP motors: a baseline motor with M19 steel and a motor made with high efficiency steel (Alloy X) developed for the project. Overall, results were as expected with comparable performance at low speeds, and with more than 8% efficiency improvement for high speeds. Increased motor steel efficiency at high frequencies not only results in direct efficiency improvements but can yield reductions in motor size and cost by facilitating higher operation speeds, or by increasing the number of poles in the machine. This allows the production of more power-dense motors which are sometimes avoided with conventional material due to increased core losses. The material developed on this project provides more viable options for achieving improved motor efficiency or reduced motor size and cost.

36 MATERIALS SCIENCE↗

DOE OSTI2025

A TOpographic Mapping (ATOM) Method to Design Magnetic Cores

Wireless power transfer offers safe, convenient, and efficient way of charging electric vehicles. Ongoing research is targeting wireless charging pad design optimization; designing the magnetic component is the most important part of the coupler design because the magnetic part determines the coupling factor and efficiency. Optimizing the coil layout and geometry as well as ferrite design requires finite elements analysis based modeling and simulation for minimized core losses, maximized magnetic coupling, and minimized material use for cost-effectiveness. Although parametric finite element analysis or emerging artificial intelligence methods can generate very accurate results, simulation times are extremely long. To address this issue, this study proposes a simple, effective core design called A TOpographic Mapping (ATOM). The proposed design is based on the design of magnetic core by using the magnetic flux distribution. The thickness of the core increases with increasing magnetic flux density, forming a variable thickness core design with less material and minimized core losses compared to conventional designs. A superimposing method is used to create an optimal design for a rotational magnetic field-based system. According to simulation results, the ATOM design reduces the required material volume by 13.19% and yields the lowest core loss and highest mutual inductance compared to other designs. In addition, misalignment, electromagnetic interference, and thermal performance were evaluated for the proposed design.

Aydin, Emrullah [Oak Ridge National Laboratory (OR↗

DOE OSTI2025

Improving Longitudinal Impedance of Inductive Inserts

In this article, we discuss methods for improving the longitudinal impedance of inductive inserts used for space charge compensation in the proton storage ring (PSR) at Los Alamos Neutron Science Center (LANSCE) Facility. The PSR relies on inductive inserts to counteract the capacitive impedance produced by the space charge of the proton beam, which can otherwise lead to beam debunching. Existing inductive inserts, which utilize Toshiba M4C21A ferrite, have been effective but require heating to reduce resistive components that can cause instabilities at higher frequencies. This article explores the potential of alternative ferrite materials, specifically National Magnetics C2050, to enhance the performance of these inserts by reducing the need for heating and minimizing resistive impedance. Through both analytical modeling and CST Particle Studio simulations, it is demonstrated that optimized ferrite materials and geometries can significantly improve space charge compensation while mitigating instability risks, ultimately enhancing the performance of the PSR.

43 PARTICLE ACCELERATORS↗

DOE OSTI2026

Design of a Cryogenic Assembly for Comparing Qubit Infrared Packaging Inefficiencies

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high-coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Mailliard, Robert J. [Fermilab] (ORCID:00090000277↗

DOE OSTI2026

Design of a Cryogenic Assembly for Comparing Qubit Infrared Packaging Inefficiencies

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high-coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Mailliard, Robert J. [Fermilab] (ORCID:00090000277↗

DOE OSTI2026

Design of a Cryogenic Assembly for Comparing Qubit Infrared Packaging Inefficiencies

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Mailliard, Robert J. [Fermilab] (ORCID:00090000277↗

DOE OSTI2026

Design of a Cryogenic Assembly for Comparing Qubit Infrared Packaging Inefficiencies

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high-coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Mailliard, Robert J. [Fermilab] (ORCID:00090000277↗

DOE OSTI2026

CMS Outer Tracker Module QA

It is well known that everything emits infrared (IR) light in the form of thermal radiation. IR radiation on superconducting qubits carries enough energy to cause decoherence and so-called “quasiparticle poisoning.” Therefore, proper IR shielding is needed to keep the qubit in a high-coherence state. However, trying to extract IR-specific information from a qubit is difficult, so a microwave kinetic inductance detector (MKID) can be used instead. We show that the IR shielding inefficiencies of MKID packages can only be compared with other packaging inefficiencies. We create a cryogenic assembly CAD design, consisting of magnetic shield cans, a copper mounting plate and mounts, and an MKID enclosure, which thermalizes the assembly to dilution refrigerator temperatures. Phase 1 of this design involves using a narrowband IR laser source to test the IR shielding of packaging at the laser’s wavelength. When the best IR shielding packaging is determined, the superconducting qubit can replace the MKID, allowing the qubit to avoid decoherence due to IR radiation and boost its performance and coherence lifetime.

Hobbeheydar, Samuel [Carnegie Mellon U. (main); Fe↗

DOE OSTI2026

Spherical tokamak physics research in preparation for the operation of NSTX-U

The National Spherical Torus Experiment Upgrade (NSTX-U) is preparing to resume operation, representing a crucial step toward realizing compact, cost-effective fusion pilot plants. In advance of this, extensive modeling and data analysis have been conducted to advance the physics basis for low-aspect-ratio, high-performance plasma regimes, focusing on three core objectives: confinement and stability, power and particle handling, and steady-state operation. Significant progress has been made in understanding the electron temperature flattening in high-β plasmas, which is shown to be driven by a complex interplay of magnetohydrodynamic instabilities (e.g. non-resonant infernal modes), fast-ion-driven Alfvén eigenmodes, and electron and ion-scale micro-instabilities, particularly Kinetic Ballooning Modes (KBMs), whose destabilization is strongly dependent on parallel magnetic field fluctuations (δB ∥ ). Furthermore, a new gyrokinetic critical pedestal model was developed, accurately predicting pedestal structure by identifying KBMs as the primary stability limit, offering a critical constraint for future high-confinement scenarios. To address the challenge of high heat flux, novel liquid lithium plasma-facing components were modeled. The analysis confirmed that lithium vapor shielding is a self-regulating mechanism for heat mitigation, while also emphasizing that strong main ion parallel flow is essential to minimize core lithium contamination. Finally, progress toward steady-state operation was anchored by developing the required physics basis and control tools. This includes predictive modeling for reversed magnetic shear sustainment, demonstrating that magnetic island-induced bootstrap current reduction is negligible in STs, and advancing real-time control and disruption avoidance capabilities. The development of high-speed surrogate models (e.g. MMMNet) provides computationally efficient tools vital for non-inductive scenario optimization and integrated, low-disruptivity operations planned for NSTX-U.

NSTX-U↗

DOE OSTI2024

Heterogeneous Integration Technologies for High-temperature, High-density, Low-profile Power Modules of Wide Bandgap Devices in Electric Drive Applications (Final Technical Report)

The goal of this project is to develop packaging technologies for making high-temperature, high-density, and low-profile wide-bandgap (WBG) power electronics modules for electric drives. These modules are aimed at enabling the DOE’s University Consortium to reach its 2025 inverter targets of ≥ 100 kW/L and ≤ 2.7 $/kW. The specific objectives are to: design and fabricate SiC half-bridge power modules with double-sided cooling and parasitic inductances < 5 nH, heat flux density > 400 W/cm 2 , and working junction temperature of 200 o C; design, fabricate, and deliver a gate driver with double-sided cooled modules for the construction of a 100 kW/L inverter at Oak Ridge National Lab; and design and prototype intelligent gate drivers with integrated current sensor and a low-profile DC-DC power supply with air-core transformer for testing power modules at 200 o C junction temperature. We followed an iterative technical approach of design, simulation, fabrication, and testing of various versions of modules, current sensors, and power supply. The state-of-the-art silicon carbide devices rated at 1.2 kV and 149 A were packaged by sintered-silver bonding on an aluminum nitride direct-bond-copper substrate for high thermal conductivity, high working temperature, and high joint reliability. Porous silver posts were used to interconnect the device’s source pads to the other direct-bond-copper substrate for low mechanical stresses, ease of manufacturing, and double-sided cooling. A current sensor based on package parasitic inductance was developed to measure switching current. A dynamic feedback scheme was developed to compensate the effect of parasitic resistance and temperature variation. A constant-current class-E dc-dc converter with air-core transformer was developed. Air-core transformer was used due to the unavailability of magnetic core at high temperatures. Gate driver and power supply were integrated with the double-side cooled, high temperature SiC power modules for testing the modules at 200 o C junction temperature. Double-pulse and continuous testing of the integrated technologies validated the design and fabrication of the three component technologies. Throughout the project, we overcame the challenge for design verification caused by low prototyping yield, which then helped train the graduate students, the future workforce, to learn the engineering know-how for low-cost manufacturing of reliable products. Below is a summary of the major accomplishments of this project: development of a prototyping process for fabricating double-side cooled (1200 V, 149 A) SiC phase-leg modules capable of working to 200 o C Tj; simulation and experimental verification of the improvement of thermo-mechanical reliability of the double-side cooled SiC phase-leg module by using rigid encapsulant; design and experimental validation of a current sensor based on package parasitic inductance and a compensation solution for eliminating the effect of parasitic resistance; design and experimental validation of a low-profile power supply with six-output air-core transformer for gate driver; functional demonstration of a SiC phase-leg module integrated with its gate driver, current sensor, and an air-core power supply at 200 o C Tj in a double-pulse switching test setup and Buck converter continuous test setup; successful completion of six PhD and two MS students who are or will work at Apple Inc., Tesla Inc., Wolfspeed Inc., Microchip Inc., Monolithic Power Systems Inc., and LG Magna Inc.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Combining molecular beam epitaxy and low-energy electron microscopy with in situ magnetic susceptibility measurements within an integrated ultrahigh vacuum system

Quantum two-dimensional materials, including ultrathin superconducting films, are of great current research interest. These films are typically fabricated under ultra-high vacuum (UHV) conditions and are sensitive to the environment—prone to oxidation and contamination when exposed to the atmosphere. This hampers the study of their intrinsic properties by standard ex situ techniques. Here, we present a variable-temperature mutual inductance probe system integrated under UHV with molecular beam epitaxy (MBE) synthesis and low-energy electron microscopy, enabling nondestructive in situ characterization of superconducting thin films. The system employs a reflection-type configuration and reaches a low temperature (∼4 K) using a high-cooling-power, vibration-isolated cryocooler. In conclusion, we demonstrate the system performance by measuring the superconducting critical temperature in a copper-oxide thin film.

2D materials↗

DOE OSTI2025

An Additively Manufactured Fe-3Si Stator for a High-Performance Electrical Motor

Additive manufacturing (AM) has the potential to produce novel high-performance electrical machines, enabling the direct printing of complex shapes and the simultaneous processing of multiple feedstocks in a single build. We examined the properties and functional performance of Fe-3 wt.% Si materials that were printed via selective laser melting, machined down to thin laminates, and stacked to form a stator core of a prototype brushless permanent-magnet electrical motor. Big Area Additive Manufacturing of Nd2Fe14B (NdFeB)–polyphenylene sulfide (PPS) bonded magnets was performed, with them then being magnetized and used for the rotor. The magnetic, mechanical, and electrical properties of the as-printed and various heat-treated thin laminates and the back electromotive force (EMF) of the electrical motors at different rotational speeds were measured. The thin laminates exhibit a maximum relative permeability of 7494 at an applied field of 0.8 Oe and a core loss of about 20 W/lb at 60 Hz with the maximum induction of 15 kg. In addition to the demonstration of AM printing, motor assembly, and complete characterization of printed Fe-3 wt.% Si, this report highlights the areas of improvement needed in printing technologies to achieve AM built electrical motors and the need for isotropic microstructure refinements to make the laminates appropriate for high-mechanical-strength and low-loss rotational electrical devices.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Time-domain all-frequency stable formulation for low-frequency electromagnetic simulation with Newmark-β time integration

An implicitly Coulomb-gauged A-ϕ formulation has previously been proposed and validated for finite ele- ment simulations of low-frequency and multiscale electromag- netic problems in the frequency domain. This formulation has demonstrated numerical stability across all frequencies, with its accuracy, efficiency, and iterative convergence established in various frequency-domain scenarios. However, direct time- domain computation is often preferable for wideband electro- magnetic problems and is typically indispensable in nonlinear and multiphysics simulations. In this work, the A-ϕ formulation is extended to the time domain. By incorporating the well-known Newmark-β time integration scheme, the proposed formulation is validated through capacitive and inductive test cases. The results confirm the solution’s accuracy and demonstrate the formulation’s stability in the time domain.

Mekonnen, Minyechil↗

DOE OSTI2024

Selective solid-state isolation of NMR circuit elements using back-to-back field effect transistors

Nuclear Magnetic Resonance (NMR) electronics that employ selective solid-state isolation of circuit elements can include solid-state switches, such as back-to-back Field Effect Transistor (FET) pairs, and isolated gate drive electronics adapted to operate the solid-state switches in order to selectively decouple induction coils from receive electronics. The solid-state switches can be placed in series to achieve higher standoff voltages, and can be configured for low on resistance and short switching times. The gate drive electronics can include electrical isolation components adapted to enhance standoff voltages and reduce electrical noise at the selectively isolated receive electronics.

Walsh, David O.↗

DOE OSTI2026

Current-Phase Relations of Superconducting PtSi Constriction Josephson Junctions

Here, we study the current-phase relations of superconductor–constriction–superconductor Josephson junctions made from platinum silicide thin films by fabricating dc-superconducting quantum interference devices incorporating pairs of junctions and measuring their magnetic-field-dependent electrical transport. By comparing the supercurrent interference patterns with numerical Ginzburg–Landau simulations, we extract the current-phase relations of individual junctions and quantify the degree of nonlinearity. These measurements show that while the constrictions themselves sustain substantial nonlinearity, the effect is moderated by the kinetic inductance of the device leads, which is an important consideration for practical superconducting circuit applications.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2025

Electromagnetic coil optimization for reduced Lorentz forces

Abstract The reduction of magnetic forces on electromagnetic coils is an important consideration in the design of high-field devices such as the stellarator or tokamak. Unfortunately, these forces may be too time-consuming to evaluate by conventional finite element modeling within an optimization loop. Although mutual forces can be computed rapidly by approximating large-bore coils as infinitely thin, this approximation does not hold for self-forces as it leads to an unphysical divergence. Recently, a novel reduced model for the self-field, self-force, and self-inductance of electromagnetic coils based on filamentary models was rigorously derived and demonstrated to be highly accurate and numerically efficient to evaluate (Hurwitz et al 2024 IEEE Trans. Magn. 60 7001614). In this paper, we present an implementation of the reduced self-force model employing automatic differentiation within the simsopt stellarator design software and use it in derivative-based coil optimization for a quasi-axisymmetric stellarator. We show that it is possible to significantly reduce point-wise forces throughout the coils, though this comes with trade-offs to fast particle losses and the minimum distance between coils and the plasma surface. The trade-off between magnetic forces and coil-surface distance is mediated by the minimum coil–coil distance for coils near the inboard side of the ‘bean’ cross-section of the plasma. The relationship between forces and fast particle losses is mediated by the normal field error. Coil forces can be lowered to a threshold with minimal deterioration to losses. Importantly, the magnet optimization approach here can be used also for tokamaks, other fusion concepts, and applications outside of fusion.

Hurwitz, Siena (ORCID:0000000166599659)↗

DOE OSTI2026

Variability of MHD instabilities in benign termination of high-current runaway electron beams in the JET and DIII-D tokamaks

Benign termination, in which magnetohydrodynamic (MHD) instabilities deconfine runaway electrons (REs) following hydrogenic injections, is a promising strategy for mitigating dangerous RE loads after disruptions. Recent experiments on the Joint European Torus (JET) have explored this scenario at higher pre-disruptive plasma currents than are achievable on other devices, revealing challenges in obtaining benign terminations at I p ≥2.5 MA. This work analyzes the evolution of these high-current RE beams and their terminating MHD events using fast magnetic sensor measurements and EFIT equilibrium reconstructions for approximately 40 JET and 20 DIII-D tokamak discharges. On JET, unsuccessful non-benign terminations occur at low edge safety factor (q edge ≈ 2), and are preceded by intermittent, non-terminating MHD events at higher rational qedge. Trends in the internal inductance I i indicate more peaked RE current profiles in the high-I p non-benign population, which may hinder successful recombination through re-ionization of the companion plasma. In contrast, benign terminations on JET typically occur at higher q edge ≥3 and exhibit less peaked RE current profiles. DIII-D displays a broader range of terminating edge safety factors, again correlated with the measured values. Across both tokamaks, the RE current peaking is therefore found to determine which MHD instability boundary is encountered, a result confirmed by linear resistive MHD modeling with the CASTOR3D code. Measured growth rates are similar for benign and non-benign cases, indicating that ideal MHD timescales at low density after hydrogenic injection do not alone explain efficient RE deconfinement. Instead, non-benign cases are most readily characterized by their comparably lower overall MHD perturbation amplitudes δB. These observations suggest that the interplay between ideal and resistive dynamics governs the termination process, with implications for extrapolating benign RE termination to high-I p reactor scenarios.

MHD instabilities↗

DOE OSTI2024

Overview of recent experimental results on the EAST Tokamak

Since the last IAEA-FEC in 2021, significant progress on the development of long pulse steady state scenario and its related key physics and technologies have been achieved, including the reproducible 403 s long-pulse steady-state H-mode plasma with pure radio frequency (RF) power heating. A thousand-second time scale (~1056 s) fully non-inductive plasma with high injected energy up to 1.73 GJ has also been achieved. The EAST operational regime of high β P has been significantly extended (H 98y2 > 1.3, β P ~ 4.0, β N ~ 2.4 and n e /n GW ~ 1.0) using RF and neutral beam injection (NBI). The full edge localized mode suppression using the n = 4 resonant magnetic perturbations has been achieved in ITER-like standard type-I ELMy H-mode plasmas with q 95 ≈ 3.1 on EAST, extrapolating favorably to the ITER baseline scenario. The sustained large ELM control and stable partial detachment have been achieved with Ne seeding. The underlying physics of plasma-beta effect for error field penetration, where toroidal effect dominates, is disclosed by comparing the results in cylindrical theory and MARS-Q simulation in EAST. Breakdown and plasma initiation at low toroidal electric fields (<0.3 V m -1 ) with EC pre-ionization is developed. A beneficial role on the lower hybrid wave injection to control the tungsten concentration in the NBI discharge is observed for the first time in EAST suggesting a potential way toward steady-state H-mode NBI operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗