Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Design tools”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

FUN3D Manual: 13.5

This manual describes the installation and execution of FUN3D (Fully-UNstructured three-dimensional CFD (Computational Fluid Dynamics) code) version 13.5, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver enables efficient gradient-based design and grid adaptation to reduce estimated discretization error. FUN3D is available with and without a reacting, real-gas capability. This generic gas option is available only for those persons that qualify for its beta release status.

Biedron, Robert T.↗
NASA NTRS2018

Distributed-Flap Layout Trade Study on a Highly Flexible Common Research Model

The results of a layout trade study of a full-span, trailing-edge flap system for the NASACommon Research Model (CRM) are presented. Previously developed analysis and design tools areused to determine the potential performance benefits of several flap layouts on a highlyflexible version of the aircraft wing. The wing is first re-twisted for optimal aerodynamicperformance at the design cruise condition while addressing aeroelastic effects. Several flaplayouts are then installed on the new baseline wing. The deflection of each segment on allflap layouts is then optimized for aerodynamic performance at an overspeed flight conditionto ascertain the effectiveness of each flap system. The results indicate that employing two-segmentflaps greatly improves overspeed performance as compared to using no or justsingle-segment flaps. The study also showed that additional segments offer only incrementalimprovements in performance. The results also show that using only four spanwise flaps canproduce meaningful performance gains. Overall, the trade study results suggest a simpledistributed flap system (four spanwise flaps with two segments each) can reduce the drag ofthe Common Research Model by 13 counts at a Mach number that is 3.5 percent higher than thedesign cruise point.

Common Research Model (CRM)↗
NASA NTRS2019

FUN3D Manual: 13.6

This manual describes the installation and execution of FUN3D version 13.6, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver enables efficient gradient-based design and grid adaptation to reduce estimated discretization error. FUN3D is available with and without a reacting, real-gas capability. This generic gas option is available only for those persons that qualify for its beta release status.

Robert T Biedron↗
NASA NTRS2020

FUN3D Manual: 13.7

This manual describes the installation and execution of FUN3D version 13.7, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for formal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.

FUN3D↗
NASA NTRS2023

FUN3D Manual: 14.0.2

This manual describes the installation and execution of FUN3D version 14.0.2, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for formal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.

William K Anderson↗
NASA NTRS2024

FUN3D Manual: 14.1

This manual describes the installation and execution of FUN3D version 14.1, including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for formal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.

William K Anderson↗
DOE OSTI2022

Developing an Ultra-Compact, Topology-Optimized Heat Exchanger using Additive Manufacturing

Traditional heat exchanger designs have relied on a plate-fin architecture, assembled in a crossflow configuration. These HX designs are limited in their maximum allowable temperature and, therefore, efficiency. More advanced designs, such as those containing counter-flow, microtube cores, can yield higher efficiencies, but generally require complex headers. The design of such headers is usually determined based on user experience rather than on rigorous design tools, which can lead to lossy architectures; conventional headers can generate up to 50% of the total pressure loss through the HX. Furthermore, the consequences of manufacturing techniques are rarely considered during the design phase. Our team has developed an ultra-compact, topology-optimized heat exchanger capable of operating in environments with temperatures and pressures up to 800°C (1472°F) and 250 bar (3626 psi), respectively. Throughout the program, the team leveraged extensive additive manufacturing research and experience in supercritical carbon dioxide (sCO 2 ) power generation experience to develop and commercialize the technology. The final power density numbers for the subscale and full-scale heat exchangers are >15 kW/kg and >50 kW/L, which includes the core and the headers. The team has involved the RTX business units, notably Collins Aerospace, in discussions for commercializing the technology.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1972

Space tools and support equipment - Current technology and future requirements.

Space tools and supporting equipment developed for past and current missions are summarized, along with projected tool and powered maneuvering aid requirements for future earth orbital missions. These tools, designed for functions such as general maintenance, replacement and repair, are reviewed and classified according to their intended application. A synopsis of the Skylab on-orbit maintenance requirements is presented, and the tools necessary for accomplishing the maintenance functions are listed. The proposed missions for future Earth Orbital Systems are summarized, and the potential functions (e.g., Remove/Replace, Cargo Transfer, etc.) are outlined. The current tool and support technology status is compared with future requirements for crew equipment to determine if these future requirements can be adequately satisfied. Of particular interest is a discussion of the augmentation of the astronaut with teleoperators (remote manipulator systems).

Brown, N. E.↗
NASA NTRS1988

OEXP Analysis Tools Workshop

This publication summarizes the software needs and available analysis tools presented at the OEXP Analysis Tools Workshop held at the NASA Langley Research Center, Hampton, Virginia on June 21 to 22, 1988. The objective of the workshop was to identify available spacecraft system (and subsystem) analysis and engineering design tools, and mission planning and analysis software that could be used for various NASA Office of Exploration (code Z) studies, specifically lunar and Mars missions.

Garrett, L. Bernard↗
NASA NTRS2003

Probabilistic Unsteady Aerodynamic Analysis

Probabilistic CFD design is needed because we are asked to do more with less. To cost effectively accomplish the design task, we need to formally quantify the effect of uncertainties (variables) in the design. Probabilistic design is one effective method to formally quantify the effect of uncertainties. Our objective is to establish a revolutionary new early design process, by developing non-deterministic physics-based probabilistic design tools, which will include all the life cycle processes. This work was concerned with the usefulness of parametric optimization method coupled with a Navier-Stokes analysis code for the aero-thermodynamic design of turbomachinery combustor liner. The interconnection between the CFD code and NESSUS codes will facilitate the coupling between the thermal profiles and structural design. We have developed new concepts for reducing the computational cost of unsteady, three-dimensional, compressible aerodynamic analyses for multistage turbomachinery flows. The flow was modeled by the three-dimensional Favre-Reynolds-averaged Navier-Stokes equations using the k-E turbulence closure, which was integrated using an implicit third-order upwind solver. The methodology developed in this work is expected to lead to the design optimization of turbomachinery blades.

Gorla, Rama S. R.↗
NASA NTRS2016

Additively Manufactured Low Cost Upper Stage Combustion Chamber

Over the past two years NASA's Low Cost Upper Stage Propulsion (LCUSP) project has developed Additive Manufacturing (AM) technologies and design tools aimed at reducing the costs and manufacturing time of regeneratively cooled rocket engine components. High pressure/high temperature combustion chambers and nozzles must be regeneratively cooled to survive their operating environment, causing their design fabrication to be costly and time consuming due to the number of individual steps and different processes required. Under LCUSP, AM technologies in Sintered Laser Melting (SLM) GRCop-84 and Electron Beam Freeform Fabrication (EBF3) Inconel 625 have been significantly advanced, allowing the team to successfully fabricate a 25k-class regenerative chamber. Estimates of the costs and schedule of future builds indicate cost reductions and significant schedule reductions will be enabled by this technology. Characterization of the microstructural and mechanical properties of the SLM-produced GRCop-84, EBF3 Inconel 625 and the interface layer between the two has been performed and indicates the properties will meet the design requirements. The LCUSP chamber is to be tested with a previously demonstrated SLM injector in order to advance the Technology Readiness Level (TRL) and demonstrate the capability of the application of these processes. NASA is advancing these technologies to reduce cost and schedule for future engine applications and commercial needs.

Protz, Christopher↗
NASA NTRS2019

Simulating Fleet Noise for Notional UAM Vehicles and Operations in New York

This paper presents the results of systems-level simulations using Metrosim that were conducted for notional Urban Air Mobility (UAM)-style vehicles analyzed for two different scenarios for New York (NY). UAM is an aviation industry term for passenger or cargo-carrying air transportation services, which are often automated, operating in an urban/city environment. UAM-style vehicles are expected to use vertical takeoff and landing with fixed wing cruise flight. Metrosim is a metroplex-wide route and airport planning tool that can also be used in standalone mode as a simulation tool. The scenarios described and reported in this paper were used to evaluate a fleet noise prediction capability for this tool. The work was a collaborative effort between the National Aeronautics and Space Administration (NASA), Intelligent Automation, Inc (IAI), and the Port Authority of New York and New Jersey (PANYNJ). One scenario was designed to represent an expanded air-taxi operation from existing helipads around Manhattan to the major New York airports. The other case represented a farther term vision case with commuters using personal air vehicles to hub locations just outside New York, with an air-taxi service running frequent connector trips to a few key locations inside Manhattan. For both scenarios, the trajectories created for the entire fleet were passed to the Aircraft Environmental Design Tool (AEDT) to generate Day-Night Level (DNL) noise contours for inspection. Without data for actual UAM vehicles available, surrogate AEDT empirical Noise-Power-Distance (NPD) tables used a similar sized current day helicopter as the Baseline, and a version of that same data linearly scaled as a first guess at possible UAM noise data. Details are provided for each of the two scenario configurations, and the output noise contours are presented for the Baseline and reduced noise DNL cases.

Glaab, Patricia↗
DOE OSTI2025

PV Degradation Modeling: Applying Geospatial Workflows with "PVDeg"

Accurate degradation modeling is essential for predicting photovoltaic (PV) module performance, estimating longevity and informing design decisions. With degradation rates varying significantly by location, geospatial analysis is critical for PV and broader applications, such as agrivoltaics, weathering and environmental data analysis. This work presents PVDeg, an open-source tool designed for geospatial degradation analysis. PVDeg integrates meteorological data from global sources, including the National Solar Radiation Database (NSRDB) and Photovoltaic Geographical Information System (PVGIS), with degradation models. The toolkit enables users to customize geospatial workflows by integrating weather data, material parameters, and user-defined Python functions. It facilitates accelerated downloads of NSRDB and PVGIS datasets and optimizes geospatial point selection to preserve data density in regions of interest. Additionally, PVDeg provides a local database for storage and spatial queries, supporting large-scale analyses without the need for high-performance computing (HPC) resources. PVDeg provides a foundational workflow that extends its utility beyond PV applications, enabling researchers to analyze geospatial processes across discipline.

14 SOLAR ENERGY↗
NASA NTRS1984

Design versus manufacturing data base management requirements

Data base management systems are valuable manufacturing and design tools as these disciplines are exceptionally information intensive, requiring precise organization and control of data processing and utilization. One such data base manager is the IPAD* system, which was originally developed to support the design process but was expanded to incorporate the additional needs of manufacturing. To set the stage, an overview of the design and manufacturing process is presented. The different functions of computers in these processes are then discussed. Finally, the design and manufacturing requirements for a data base manager are compared and contrasted.

Mckenna, E. G.↗
NASA NTRS1995

Shuttle orbiter experiments: Use of an operational vehicle for advancement and validation of space systems design technologies

The NASA Orbiter Experiments (OEX) Program provided a mechanism for utilization of an operational space shuttle orbiter as a flight research vehicle, as an adjunct to its normal space transportation mission. OEX Program experiments were unique among orbiter payloads, as the research instrumentation for these experiments were carried as integral parts of the vehicle's structure, rather than being placed in the orbiter's payload bay as mission-unique cargo. On each of its first 17 flights, the Orbiter Columbia carried some type of research instrumentation. Various instrumentation systems were used to measure, in flight, the requisite parameters for determination of the orbiter aerodynamic characteristics over the entire entry flight regime and/or the aerodynamic-heating rates imposed upon the vehicle during the hypersonic portion of atmospheric entry. The data derived from this instrumentation represent benchmark hypersonic flight data heretofore unavailable for a lifting entry vehicle. The data are being used in a continual process of validation of state-of-the-art methods, both experimental and computational, for simulating/predicting the aerodynamic and aerothermal characteristics of advanced space transportation vehicles. This paper describes the OEX Program complement of research experiments, presents typical flight data obtained by these experiments, and demonstrates the utilization of these data for advancement and validation of vehicle aerothermodynamic-design tools. By example, the concept of instrumenting operational vehicles and/or spacecraft in order to perform advanced technology development and validation is demonstrated to be an effective and economical method for maturing space-systems design technologies.

Holloway, Paul F.↗
NASA NTRS2022

FUN3D Manual: 14.0

This manual describes the installation and execution of FUN3D version 14.0,including optional dependent packages. FUN3D is a suite of computational fluid dynamics simulation and design tools that uses mixed-element unstructured grids in a large number of formats, including structured multiblock and overset grid systems. A discretely-exact adjoint solver may be used for for-mal design optimization, error estimation, and mesh adaptation. FUN3D also offers a reacting, real-gas capability and provides GPU acceleration of many common simulation options.1

William K Anderson↗
NASA NTRS2023

Computational Aerothermal Modeling and Simulation of Hypersonic, Low-density Flows for the ADEPT Drag Modulated Aerocapture Mission

NASA Ames Entry Systems and Technology Division has been leading development and testing of the Adaptable, Deployable, Entry and Placement Technology (ADEPT). A teaming partnership with JPL has been established to study and develop a compelling application of the ADEPT mechanically deployable hypersonic decelerator as part of the Venus Drag Modulated Aerocapture (VDMA) JPL R&TD effort. The primary work of this activity is to develop a design tool for the ADEPT drag skirt (e.g. a CFD-anchored CBAERO model) that enables rapid estimation of aerothermal environments for a range of candidate trajectories. This capability will enable rapid feasibility trades and design assessments for early stage mission concept evaluation for ADEPT Drag Modulated Aerocapture applications. Results of using TPSizer provided an ADEPT carbon fabric design thickness of the required number of fabric layers needed for predicted aerothermal environments and still have sufficient fabric remaining for overall vehicle integrity. This resulted in aerothermal design closure of the ADEPT drag skirt. In addition, the similar methodology for Venus DMA was used to assess a similar DMA operation at Earth as part of a possible Technology Demonstration Mission (TDM) for ADEPT DMA. This analysis showed that there is a close similarity of design approaches for an Earth DMA TDM that would be applicable to Venus DMA mission designs.

Drag Modulated Aerocapture↗
DOE OSTI2025

PDnetwork

PDnetwork is an interactive online tool designed to visualize the evolution of the co-authorship network in the field of peridynamics. In this network, each node represents a peridynamics author, and each link represents co-authorship between authors. The tool allows users to obtain collaborative measures for authors using selected network metrics and visualize collaborations for specific authors. Additionally, it provides rankings for authors based on selected collaboration metrics and includes links to the author profiles in the Scopus publication database.

Dahal, Biraj [Georgia Institute of Technology, Atl↗