Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design augmentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Lunar Landing Trajectory Design for Onboard Hazard Detection and Avoidance

The Autonomous Landing and Hazard Avoidance Technology (ALHAT) Project is developing the software and hardware technology needed to support a safe and precise landing for the next generation of lunar missions. ALHAT provides this capability through terrain-relative navigation measurements to enhance global-scale precision, an onboard hazard detection system to select safe landing locations, and an Autonomous Guidance, Navigation, and Control (AGNC) capability to process these measurements and safely direct the vehicle to a landing location. This paper focuses on the key trajectory design issues relevant to providing an onboard Hazard Detection and Avoidance (HDA) capability for the lander. Hazard detection can be accomplished by the crew visually scanning the terrain through a window, a sensor system imaging the terrain, or some combination of both. For ALHAT, this hazard detection activity is provided by a sensor system, which either augments the crew s perception or entirely replaces the crew in the case of a robotic landing. Detecting hazards influences the trajectory design by requiring the proper perspective, range to the landing site, and sufficient time to view the terrain. Following this, the trajectory design must provide additional time to process this information and make a decision about where to safely land. During the final part of the HDA process, the trajectory design must provide sufficient margin to enable a hazard avoidance maneuver. In order to demonstrate the effects of these constraints on the landing trajectory, a tradespace of trajectory designs was created for the initial ALHAT Design Analysis Cycle (ALDAC-1) and each case evaluated with these HDA constraints active. The ALHAT analysis process, described in this paper, narrows down this tradespace and subsequently better defines the trajectory design needed to support onboard HDA. Future ALDACs will enhance this trajectory design by balancing these issues and others in an overall system design process.

Paschall, Steve↗
DOE OSTI2025

Advances in high-pressure and high-temperature heat exchangers: Innovations via additive manufacturing and their applications

This paper provides a comprehensive overview of technological developments and applications for high-pressure and high-temperature (HPHT) heat exchangers produced through additive manufacturing (AM) techniques. As the demand for high-efficiency energy systems has been rising, the role of heat exchangers for thermal management and transport is becoming increasingly crucial. In this context, AM has emerged as a promising manufacturing solution to address the challenges posed by higher operating temperatures and/or pressures. This paper delves into three primary areas: the exploration of HPHT regimes supported by conventional heat exchangers, the impact of AM processes on thermal transport devices, and the discussion focused on HPHT heat exchangers produced via AM. The study examines the traditional manufacturing processes, materials, structures and geometries, and limitations of the commonly used heat exchangers for HPHT applications. Furthermore, it highlights the potential of AM in optimizing HPHT heat exchanger design, by reviewing studies that enable uniform flow distribution, minimization of fouling, and thermo-hydraulic performance augmentation without compromising structural stability. While addressing the limitations of cost, size, and other constraints, this study offers insights into the possibilities of AM in revolutionizing HPHT heat exchanger technology. The goal has been to fill the gap in literature by summarizing key studies, findings, and limitations, presenting a detailed examination, and proposing new areas for research. In conclusion, this review contributes to a deeper understanding of AM’s role in advancing HPHT heat exchangers for future energy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Statorless mixed flow turbine for transonic pulsating inflow

Effective harvesting of power from high speed highly transient inflows such as the outflow of rotating detonation combustors (RDCs) is key to achieving their promised cycle efficiency step jump. To increase power density and efficiency simultaneously, a concept that can directly ingest transonic outflow, addressing the choking is needed, i.e. without additional transition elements. A new statorless design was assessed using a comprehensive approach to quantify all contributions to loss generation in transient flows, locally and globally. The turbine rotor was designed under steady flow conditions with a genetic algorithm. The comparison of power and loss generation between steady and unsteady flow results shows that a design methodology under steady-state conditions is suitable to characterize the performance of different designs. Three design families were further assessed under highly transient transonic conditions including traveling shock waves with a relative total pressure amplitude of 149.6% around the mean value and inflow angle variations from -26.5 deg to +51.8 deg. The oblique shock impinging on the pressure side (PS) of the turbine augments the shaft power extraction. When the oblique shock reflects between the pressure side and suction side (SS), its strength diminishes. This paper provides design guidelines on efficient turbine work extraction from the shocks emanating from detonation combustors.

rotating detonation engines↗
DOE OSTI2021

SAGE Intrusion Detection System: Sensitivity Analysis Guided Explainability for Machine Learning.

This report details the results of a three-fold investigation of sensitivity analysis (SA) for machine learning (ML) explainability (MLE): (1) the mathematical assessment of the fidelity of an explanation with respect to a learned ML model, (2) quantifying the trustworthiness of a prediction, and (3) the impact of MLE on the efficiency of end-users through multiple users studies. We focused on the cybersecurity domain as the data is inherently non-intuitive. As ML is being using in an increasing number of domains, including domains where being wrong can elicit high consequences, MLE has been proposed as a means of generating trust in a learned ML models by end users. However, little analysis has been performed to determine if the explanations accurately represent the target model and they themselves should be trusted beyond subjective inspection. Current state-of-the-art MLE techniques only provide a list of important features based on heuristic measures and/or make certain assumptions about the data and the model which are not representative of the real-world data and models. Further, most are designed without considering the usefulness by an end-user in a broader context. To address these issues, we present a notion of explanation fidelity based on Shapley values from cooperative game theory. We find that all of the investigated MLE explainability methods produce explanations that are incongruent with the ML model that is being explained. This is because they make critical assumptions about feature independence and linear feature interactions for computational reasons. We also find that in deployed, explanations are rarely used due to a variety of reason including that there are several other tools which are trusted more than the explanations and there is little incentive to use the explanations. In the cases when the explanations are used, we found that there is the danger that explanations persuade the end users to wrongly accept false positives and false negatives. However, ML model developers and maintainers find the explanations more useful to help ensure that the ML model does not have obvious biases. In light of these findings, we suggest a number of future directions including developing MLE methods that directly model non-linear model interactions and including design principles that take into account the usefulness of explanations to the end user. We also augment explanations with a set of trustworthiness measures that measure geometric aspects of the data to determine if the model output should be trusted.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1973

Space tug.

The reusable space tug is a major system being planned for use with the space shuttle to augment its capability to deliver, retrieve, and support automated payloads. The reusable space tug will be designed to support all the planned missions beyond low earth orbit including geosynchronous orbit. Tug missions and requirements are discussed together with tug options, giving attention to existing transfer stages and growth stages. System studies for an interim tug concept are planned to begin in February 1973. Three independent studies will be conducted: two on cryogenic tugs and one on storable propellant tugs.-

Huber, W. G.↗
NASA NTRS1977

Analytical screening of low emissions, high performance duct burners for supersonic cruise aircraft engines

An analytical screening study was conducted to identify duct burner concepts capable of providing low emissions and high performance in advanced supersonic engines. Duct burner configurations ranging from current augmenter technology to advanced concepts such as premix-prevaporized burners were defined. Aerothermal and mechanical design studies provided the basis for screening these configurations using the criteria of emissions, performance, engine compatibility, cost, weight and relative risk. Technology levels derived from recently defined experimental low emissions main burners are required to achieve both low emissions and high performance goals. A configuration based on the Vorbix (Vortex burning and mixing) combustor concept was analytically determined to meet the performance goals and is consistent with the fan duct envelope of a variable cycle engine. The duct burner configuration has a moderate risk level compatible with the schedule of anticipated experimental programs.

Lohmann, R. A.↗
NASA NTRS1978

The effect of prefilter design on sample rate selection in digital flight control systems

The effect of prefilters on sample rate selection is examined and design procedures are determined for obtaining the best combination of prefilter breakpoint and sample rate. The employed approach involves a quantitative comparison of the output noise response of systems originating from the same basic plant and designed over a wide range of prefilters and sample rates. Each system design was carefully tailored so that it exhibited approximately identical responses to commands. The results presented augment the criteria for sample rate selection which have been discussed by Powell and Katz (1975). Attention is given to system characteristics, an integrator as a plant, and the short period motion of the F-8 aircraft.

Peled, U.↗
NASA NTRS1979

Modular heat pipe radiators for enhanced Shuttle mission capabilities

Current heat pipe radiator technology is reviewed and the results from three state-of-the-art hardware programs are summarized. Heat pipe radiators are shown to be an improvement over all-fluid loop panels for long duration space missions, when micrometeoroid survivability is important. Finally, several heat pipe radiator design concepts are presented which would enhance Shuttle mission capabilities by either extending mission life and/or augmenting heat rejection capability.

Alario, J.↗
NASA NTRS1982

Space Shuttle flying qualities and flight control system assessment

This paper reviews issues, data, and analyses relevant to the longitudinal flying qualities of the Space Shuttle in approach and landing. The manual control of attitude and path are first examined theoretically to demonstrate the unconventional nature of the Shuttle's augmented pitch and path response characteristics. The time domain pitch rate transient response criterion used for design of the Shuttle flight control system is examined in context with data from recent flying qualities experiments and operational aircraft. Questions arising from this examination are addressed through comparisons with MIL-F-8785C and other proposed flying qualities criteria which indicate potential longitudinal flying qualities problems. However, it is shown that these criteria, based largely on data from conventional aircraft, may be inappropriate for assessing the Shuttle.

Myers, T. T.↗
NASA NTRS1988

Longitudinal long-period dynamics of aerospace craft

Linear analyses are performed to examine the generic aspects of aerospace vehicle longitudinal long-period or trajectory modes of motion. The influence of Mach number, dynamic pressure, thrust-to-drag ratio, and propulsion system thrust laws on the longitudinal trajectory modes is presented in terms of phugoid frequency and damping and height mode stability. The results of these analyses are compared to flying qualities requirements where possible, and potential deficiencies in both the vehicle and the criteria are noted. A preliminary look at possible augmentation schemes to improve potential deficiencies is also presented. Interpretation of the practical consequences of the results is aided by typical time histories. Results indicate that propulsion system characteristics are the dominant influence on the longitudinal long-period flight dynamics of hypersonic aerospace craft. However, straightforward augmentation systems demonstrated the potential to accommodate these influences if the effects are included in the design process. These efforts may be hampered by a lack of design criteria for hypersonic aircraft.

Berry, Donald T.↗
NASA NTRS1996

Deforestation and Biogenic Trace Emissions from Brazilian Cerrado

The overall goal of NASA's SCAR (Smoke, Cloud and Radiation) Program is to obtain physical and chemical properties of the smoke produced by biomass burning and the effects of the smoke on the earth's radiation balance and climate. It is a joint project with the Brazilian government and their organizations, including INPE (Instituto Nacional Pesquisas Espaciais) who actively participate in all activities. Appropriate estimates of the biomass buming in the tropics is therefore essential to determine its effect on the atmosphere and on climate. The SCAR series of experiments is designed with that purpose. The present study of evaluating the burnt-out areas is to augment the data collected to date to help evaluate the effect of biomass burning.

Sinha, Ravi↗
NASA NTRS1998

Aerothermal Effects of Cavities and Protuberances for High-Speed Sample Return Capsules

Extraterrestrial sample return is a growing component of solar system exploration. Currently, four missions, Stardust, 1 Muses-C, 2 Genesis, and Mars Sample Return, are under development that employ sample return as a prime component of the mission architecture. Respectively, these missions will return samples from the tail of a comet, an asteroid, the solar wind, and, Mars. An important component of these missions and the focus of this paper is the design of the sample return capsule (SRC). The purpose of the SRC is to safely return to Earth any gathered samples for terrestrial analysis. The two major design constraints for any SRC are as follows: 1) it must be able to survive a high-speed Earth entry (11 km/s to as a high as 15 km/s), 2) the mass of the SRC must be as small as possible. Because the SRC mass is carried from Earth to the sample sight and back, the SRC mass is a strong driver in the mission mass budget. Further, for the Mars Sample Return Capsule, planetary protection is another constraint. For this capsule, the probability of planetary contamination at Earth due to an SRC failure at entry must be minimal. For an SRC, a possible failure mechanism is severe local heating as a result of cavities and or protuberances in the SRC forebody heatshield. For example, the Apollo Command Module had a number of cavities and protuberances as part of the baseline designs Wind-tunnel tests of models containing small cavities and protuberances showed severe local heating augmentations in the vicinity of these surface discontinuities.4-5 As another example, the Genesis SRC forebody heat-shield contains penetrations (cavities) to mount the vehicle to the carrier bus. It is expected that these penetrations will also experience a severe local heating environment. A concern is that the large thermal gradients may produce sufficient thermal stress to cause local mechanical failure of the heatshield. Penetrations to the forebody heat-shield can also result from damage at vehicle integration, during launch, or during transportation of the sample return capsule from earth to the sample site and back. For example, the Starting SRC was damaged near the shoulder during the heatshield integration process producing a local surface discontinuity. Also, the Starting SRC traverses through the tail of a comet and is in space for 7 years. Thus, damage to the heatshield as a result of micrometeroid impact is a concern. Finally, it is difficult to characterize the effects of these potential heatshield singularities with ground-test facilities. Either detailed simulation or a dedicated flight test is required.

Olynick, David↗
NASA NTRS2013

Application of Adjoint Methodology to Supersonic Aircraft Design Using Reversed Equivalent Areas

This paper presents an approach to shape an aircraft to equivalent area based objectives using the discrete adjoint approach. Equivalent areas can be obtained either using reversed augmented Burgers equation or direct conversion of off-body pressures into equivalent area. Formal coupling with CFD allows computation of sensitivities of equivalent area objectives with respect to aircraft shape parameters. The exactness of the adjoint sensitivities is verified against derivatives obtained using the complex step approach. This methodology has the benefit of using designer-friendly equivalent areas in the shape design of low-boom aircraft. Shape optimization results with equivalent area cost functionals are discussed and further refined using ground loudness based objectives.

Rallabhandi, Sriram K.↗
NASA NTRSDate not supplied

Development of Urban Air Mobility (UAM) Vehicles for Ease of Operation

To date the air transportation system has been developed with the in-cremental introduction of new technology and with highly experienced air transport pilots and air traffic controllers overseeing flight operations. Thus, we currently have one of the safest commercial aviation systems in the world. General Aviation (GA) in the United States, however, has not always followed the same cautious and monitored approach to implementation; consequently, the GA safety record does not meet the high standards of commercial aviation. Recently, a new system known as Urban Air Mobility (UAM), is attracting considerable interest and investment from industry and government agencies. UAM refers to a system of passenger and small-cargo air transportation vehicles within an urban area with the goal of reducing the number of times we need to use our cars, thus improving urban traffic by moving people and cargo from crowded single pas-senger vehicles on our roads to personal and on-demand air vehicles. These UAM vehicles will be small and based on electric, Vertical-Take-Off-and-Landing (eV-TOL) systems. A significant component of UAM is offloading of flight-man-agement responsibilities from human pilots to newly-developed autonomy. Cur-rently, over 100 UAM vehicles are either in development or production. Most, if not all, have a goal of fully autonomous vehicle operations, but fully autonomous flying vehicles are not expected in the near future. Therefore, we are de-veloping concepts for UAM vehicles that will be easy to fly and/or manage by operators with minimal pilot training. In this paper we will discuss our human-automation teaming approach to develop an easy-to-operate VTOL aircraft, and some of the fly-by-wire technology needed to stabilize the vehicle so that a sim-ple ecological mental model of the flying task can be implemented. We will discuss the requirements for a stability augmentation system that must be developed to support our simple pilot input model, and also present design guidelines and requirements based on a pilot input and management model. Finally, our ap-proach to vehicle development will involve considerable operator testing and evaluation: improving pilot model, inceptors, displays and also work on a plan for how a UAM vehicle can be integrated with terminal area air traffic control airspace with minimal impact on controller workload.

UAM↗
NASA NTRS1977

Study to design and develop remote manipulator systems

A description is given of part of a continuing effort both to develop models for and to augment the performance of humans controlling remote manipulators. The project plan calls for the performance of several standard tasks with a number of different manipulators, controls, and viewing conditions, using an automated performance measuring system; in addition, the project plan calls for the development of a force-reflecting joystick and supervisory display system.

Hill, J. W.↗
DOE OSTI2024

Differentiable Multiphysics Codes: A Breakthrough Technology for Simulation and Computing

This document summarizes the findings of a strategic planning exercise commissioned by the Weapons Simulation and Computing, Computational Physics (WSC/CP) program at the Lawrence Livermore National Laboratory (LLNL) in FY24. During the year, the committee met with multiple stakeholder communities to gather input, opinions, suggestions and concerns which have been incorporated throughout this document. The key findings from this exercise are summarized: • The development of multiphysics modelling and simulation (mod/sim) codes and software technologies, their deployment on exascale compute platforms, and their broad adoption across the NNSA is a major success of the Advanced Simulation and Computing (ASC) program and the Exascale Computing Project (ECP). Sustained investment in these core technologies is essential. • Today’s state of the art involves running ensembles of O(100K) simulations to perform uncertainty quantification (UQ) and design studies using multiple statistical methods such as Bayesian optimization to understand sensitivities of our models and explore parameterized design spaces. Even with exascale computing, we are practically limited to O(10) parameters in these studies since the number of simulations required to sample the space scales exponentially with the number of design parameters. • The data from these simulation ensembles is increasingly being used to train machine learned (ML) surrogates (or reduced order models, ROMs) which can then be used for optimization or real time design exploration. However, the trained surrogates are still limited in the number of parameters they can represent due to the sampling limitations previously noted. • Augmenting our suite of integrated multiphysics simulation codes, both current and emerging, with the ability to compute gradients (solution derivatives) of arbitrary simulation outputs with respect to (some or all) simulation inputs would be a breakthrough technology, opening the door to a new era of efficient and automated inverse design based on verified and validated mod/sim capabilities. • This capability, which we refer to as differentiable multiphysics codes (DMCs), would revolutionize both UQ and optimization studies by breaking the curse of dimensionality that presently limits our “gradient-free” ensemble based computing approach. A similar breakthrough occurred in the AI/ML community once the ability to compute gradients of arbitrary loss functions using back-propagation became commonplace. Gradient information from the multiphysics codes can also be used to dramatically improve the efficiency and scale of training of ML/ROM surrogates for rapid assessments. • Achieving this in our suite of codes will be a grand challenge, similar to the amount of effort that was required to transition from CPU to GPU computing. It will require buy-in from the entire WSC/CP program and beyond, including all integrated codes, physics and engineering models, third-party library dependencies and performance portability abstractions. It will also require investment in research and development of numerical methods for computing adjoints of coupled physics across multiple adaptively refined moving meshes and of stochastic (Monte Carlo) and mesh free (SPH) methods. • New software and numerical techniques, largely pioneered by the AI/ML community, make this feasible. Chief among these is automatic differentiation (AD), the ability to employ AD at point-wise locations in a physics calculation (instead of traditional black-box approaches) and the ability to perform “back-propagation in time” (or reverse mode AD) for non-linear partial differential equations (PDEs). Fundamentally, the conclusion of this strategic planning exercise is that the time is right to undertake a large scale effort in WSC, centered on the existing integrated codes, to continue the natural evolution of mod/sim in the age of AI/ML. Instead of attempting to replace mod/sim with purely data driven AI/ML models, we believe the key to success is to integrate AI/ML by building on top of the decades of hard-won knowledge and the verified/validated multiphysics modelling capability that is the hallmark of the ASC program.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2013

Simulator Study of Indoor Annoyance Caused by Shaped Sonic Boom Stimuli With and Without Rattle Augmentation

The National Aeronautics and Space Administration's High Speed Project is developing a predictive capability for annoyance caused by shaped sonic booms transmitted indoors. The predictive capability is intended for use by aircraft designers as well as by aircraft noise regulators who are considering lifting the current prohibition on overland civil supersonic flight. The goal of the current study is to use an indoor simulator to validate two models developed using headphone tests for annoyance caused by sonic booms with and without rattle augmentation. The predictors in the proposed models include Moore and Glasberg's Stationary Loudness Level, the time derivative of Moore and Glasberg's time-varying short-term Loudness Level, and the difference between two weighted sound exposure levels, CSEL-ASEL. The indoor simulator provides a more realistic listening environment than headphones due to lowfrequency sound reproduction down to 6 Hz, which also causes perceptible tactile vibration. The results of this study show that a model consisting of {PL + (CSEL-ASEL)} is a reliable predictor of annoyance caused by shaped sonic booms alone, rattle sounds alone, and shaped sonic booms and rattle sounds together.

Rathsam, Jonathan↗
NASA NTRS2016

Augmenting Parametric Optimal Ascent Trajectory Modeling with Graph Theory

It has been well documented that decisions made in the early stages of Conceptual and Pre-Conceptual design commit up to 80% of total Life-Cycle Cost (LCC) while engineers know the least about the product they are designing [1]. Once within Preliminary and Detailed design however, making changes to the design becomes far more difficult to enact in both cost and schedule. Primarily this has been due to a lack of detailed data usually uncovered later during the Preliminary and Detailed design phases. In our current budget-constrained environment, making decisions within Conceptual and Pre-Conceptual design which minimize LCC while meeting requirements is paramount to a program's success. Within the arena of launch vehicle design, optimizing the ascent trajectory is critical for minimizing the costs present within such concerns as propellant, aerodynamic, aeroheating, and acceleration loads while meeting requirements such as payload delivered to a desired orbit. In order to optimize the vehicle design its constraints and requirements must be known, however as the design cycle proceeds it is all but inevitable that the conditions will change. Upon that change, the previously optimized trajectory may no longer be optimal, or meet design requirements. The current paradigm for adjusting to these updates is generating point solutions for every change in the design's requirements [2]. This can be a tedious, time-consuming task as changes in virtually any piece of a launch vehicle's design can have a disproportionately large effect on the ascent trajectory, as the solution space of the trajectory optimization problem is both non-linear and multimodal [3]. In addition, an industry standard tool, Program to Optimize Simulated Trajectories (POST), requires an expert analyst to produce simulated trajectories that are feasible and optimal [4]. In a previous publication the authors presented a method for combatting these challenges [5]. In order to bring more detailed information into Conceptual and Pre-Conceptual design, knowledge of the effects originating from changes to the vehicle must be calculated. In order to do this, a model capable of quantitatively describing any vehicle within the entire design space under consideration must be constructed. This model must be based upon analysis of acceptable fidelity, which in this work comes from POST. Design space interrogation can be achieved with surrogate modeling, a parametric, polynomial equation representing a tool. A surrogate model must be informed by data from the tool with enough points to represent the solution space for the chosen number of variables with an acceptable level of error. Therefore, Design Of Experiments (DOE) is used to select points within the design space to maximize information gained on the design space while minimizing number of data points required. To represent a design space with a non-trivial number of variable parameters the number of points required still represent an amount of work which would take an inordinate amount of time via the current paradigm of manual analysis, and so an automated method was developed. The best practices of expert trajectory analysts working within NASA Marshall's Advanced Concepts Office (ACO) were implemented within a tool called multiPOST. These practices include how to use the output data from a previous run of POST to inform the next, determining whether a trajectory solution is feasible from a real-world perspective, and how to handle program execution errors. The tool was then augmented with multiprocessing capability to enable analysis on multiple trajectories simultaneously, allowing throughput to scale with available computational resources. In this update to the previous work the authors discuss issues with the method and solutions.

Patrick D Dees↗