Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MOSFETs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Thermal Optimization and Experimental Demonstration of a Silicon Carbide, Half-Bridge Power Module

This paper describes modeling and experimental work to design and demonstrate a silicon carbide (SiC), single-side-cooled power module. Two SiC metal-oxide-semiconductor field-effect transistors (MOSFET) were used for each switch position and packaged on a metalized ceramic substrate. Thermal modeling was first conducted to optimize the module packaging to minimize junction-to-fluid thermal resistance and device temperature variations. This procedure identified the optimal device placement and baseplate thickness to maximize thermal performance. A heat exchanger - incorporating impinging jets of water-ethylene glycol - was designed to cool the module's baseplate to minimize thermal resistance and pumping power. The heat exchanger used relatively low fluid velocities (<1.5 m/s) to minimize erosion-corrosion effects and relatively large fluid channel sizes (>=1 mm) to prevent clogging. The power module concept was fabricated, and experiments were conducted to measure its thermal performance. Direct current was used to power the module devices, and junction temperatures were measured via device temperature-sensitive parameters. The experimental results were found to be in good agreement with model predictions (within 2%) and yielded junction-to-fluid thermal resistance values as low as about 15 mm2 K/W at relatively low pumping power values. The results demonstrate the improved performance associated with jet impingement cooling and represent an improvement over existing channel-flow-type cold plates, which can enable improvements to power density and reliability.

36 MATERIALS SCIENCE↗

Gallium nitride based power switches for next generation of power conversion

Power conversion impacts all areas of electricity consumption, including motion control, lighting, air conditioning, and information technology. Si, the workhorse of the industry, has served well so far but reached its material limits. To keep up with the advancement of technologies enabling new conveniences, power conversion techniques need to go through significant transformation that calls for the next generation semiconductor for power switching. SiC and GaN, which have the potential to push the envelope beyond Si providing solutions for the entire range of power conversion at higher efficiencies and reduced form factors. GaN HEMTs have an added advantage over SiC MOSFETs owing to the high-mobility electron channel formed at the AlGaN/GaN interface, which has been the basis of radio frequency amplifiers. GaN has enabled systems that can run with lesser cooling at frequencies at least ten times higher than current Si-based systems, significantly reducing the form factor both electrically (passive components) and mechanically (heat sinks). The high current and voltage required for high power conversion application make the chip area in a lateral topology uneconomical and difficult to manufacture. Vertical GaN devices on bulk GaN substrates complete the portfolio of power switches required to address the power conversion market.

Chowdhury, S↗

Insulating gallium oxide layer produced by thermal oxidation of gallium-polar GaN: Insulating gallium oxide layer produced by thermal oxidation of gallium-polar GaN

We report the benefits of dry oxidation of n -GaN for the fabrication of metal-oxide-semiconductor structures. GaN thin films grown on sapphire by MOCVD were thermally oxidized for 30, 45 and 60 minutes in a pure oxygen atmosphere at 850 °C to produce thin, smooth GaO x layers. Moreover, the GaN sample oxidized for 30 minutes had the best properties. Its surface roughness (0.595 nm) as measured by atomic force microscopy (AFM) was the lowest. Capacitance-voltage measurements showed it had the best saturation in accumulation region and the sharpest transition from accumulation to depletion regions. Under gate voltage sweep, capacitance-voltage hysteresis was completely absent. The interface trap density was minimum (D it = 2.75×10 10 cm –2 eV –1 ) for sample oxidized for 30 mins. These results demonstrate a high quality GaO x layer is beneficial for GaN MOSFETs.

36 MATERIALS SCIENCE↗

Interfacial Transition Regions at Germanium/Hf Oxide Based Dielectric Interfaces: Qualitative Differences Between Non-Crystalline Hf Si Oxynitride and Nanocrystalline HfO2 Gate Stacks

The contribution from a relatively low-K SiON (K {approx} 6) interfacial transition region (ITR) between Si and transition metal high-K gate dielectrics such as nanocrystalline HfO2 (K {approx} 20), and non-crystalline Hf Si oxynitride (K {approx} 10-12) places a significant limitation on equivalent oxide thickness (EOT) scaling. This limitation is equally significant for metal-oxide-semiconductor capacitors and field effect transistors, MOSCAPs and MOSFETs, respectively, fabricated on Ge substrates. This article uses a novel remote plasma processing approach to remove native Ge ITRs and bond transition metal gate dielectrics directly onto crystalline Ge substrates. Proceeding in this way we identify (i) the source of significant electron trapping at interfaces between Ge and Ge native oxide, nitride and oxynitride ITRs, and (ii) a methodology for eliminating native oxide, or nitride IRTs on Ge, and achieving direct contact between nanocrystalline HfO2 and non-crystalline high Si3N4 content Hf Si oxynitride alloys, and crystalline Ge substrates. We then combine spectroscopic studies, theory and modeling with electrical measurements to demonstrate the relative performance of qualitatively different nanocrystalline and non-crystalline gate dielectrics for MOS Ge test devices.

36 MATERIALS SCIENCE↗

A portable and reusable sensor system based on graphene for real-time and sensitive detection of lead ions in water

Long-term exposure to Pb 2+ can cause irreversible damage to the nervous, cardiovascular, and reproductive systems. Therefore, developing a fast and sensitive detection system capable of monitoring minuscule concentrations of Pb 2+ is essential. In this study, we demonstrated a fully portable sensor system enabling rapid, sensitive, and real-time monitoring of Pb 2+ . The sensor system adopted the remote-gate field-effect transistor (RGFET) detection scheme and was easy to operate, even for non-experts. The sensor system comprised two printed circuit boards (PCBs): a sensor PCB with a remote-gate electrode and an analyzer PCB with a metal-oxide-semiconductor field-effect transistor (MOSFET) transducer and peripheral electronics to manage sensor signals. To achieve a high sensitivity for Pb 2+ , we utilized graphene ink drop-casted on the sensor PCB as a sensing membrane. The graphene film was easy to deposit and remove, enabling the sensor PCB to be reused multiple times. The sensor system was further linked to a smartphone application that instantly monitors the sensor response, allowing for rapid point-of-use detection. The sensor exhibited a high sensitivity of 21.7% when the limit of detection (LOD) value of 1 nM (∼0.2 ppb) was detected, and the typical detection time for each sample was approximately 60 seconds. This portable sensor system advances sensing technologies and could potentially supplement expensive, laborious conventional sensing equipment.

54 ENVIRONMENTAL SCIENCES↗

Potential High Resolution Dosimeters For MRT

Microbeam Radiation Therapy (MRT) uses highly collimated, quasi-parallel arrays of X-ray microbeams of 50-600 keV, produced by 2nd and 3rd generation synchrotron sources, such as the National Synchrotron Light Source (NSLS) in the U.S., and the European Synchrotron Radiation Facility (ESRF) in France, respectively. High dose rates are necessary to deliver therapeutic doses in microscopic volumes, to avoid spreading of the microbeams by cardiosynchronous movement of the tissues. A small beam divergence and a filtered white beam spectrum in the energy range between 30 and 250 keV results in the advantage of steep dose gradients with a sharper penumbra than that produced in conventional radiotherapy. MRT research over the past 20 years has allowed a vast number of results from preclinical trials on different animal models, including mice, rats, piglets and rabbits. Microbeams in the range between 10 and 100 micron width show an unprecedented sparing of normal radiosensitive tissues as well as preferential damage to malignant tumor tissues. Typically, MRT uses arrays of narrow ({approx}25-100 micron-wide) microplanar beams separated by wider (100-400 microns centre-to-centre, c-t-c) microplanar spaces. We note that thicker microbeams of 0.1-0.68 mm used by investigators at the NSLS are still called microbeams, although some invesigators in the community prefer to call them minibeams. This report, however, limits it discussion to 25-100 {mu}m microbeams. Peak entrance doses of several hundreds of Gy are surprisingly well tolerated by normal tissues. High resolution dosimetry has been developed over the last two decades, but typical dose ranges are adapted to dose delivery in conventional Radiation Therapy (RT). Spatial resolution in the sub-millimetric range has been achieved, which is currently required for quality assurance measurements in Gamma-knife RT. Most typical commercially available detectors are not suitable for MRT applications at a dose rate of 16000 Gy/s, micron resolution and a dose range over several orders of magnitude. This paper will give an overview of all dosimeters tested in the past at the ESRF with their advantages and drawbacks. These detectors comprise: Ionization chambers, Alanine Dosimeters, MOSFET detectors, Gafchromic registered films, Radiochromic polymers, TLDs, Polymer gels, Fluorescent Nuclear Track Detectors (Al{sub 2}O{sub 3}:C, Mg single crystal detectors), OSL detectors and Floating Gate-based dosimetry system. The aim of such a comparison shall help with a decision on which of these approaches is most suitable for high resolution dose measurements in MRT. The principle of these detectors will be presented including a comparison for some dosimeters exposed with the same irradiation geometry, namely a 1x1 cm{sup 5} field size with microbeam exposures at the surface, 0.1 cm and 1 cm in depth of a PMMA phantom. For these test exposures, the most relevant irradiation parameters for future clinical trials have been chosen: 50 micron FWHM and 400 micron c-t-c distance. The experimental data are compared with Monte Carlo calculations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Maskless regrowth of GaN for trenched devices by MOCVD

Blanket regrowth studies were performed on GaN trenches with varying widths and optimized for two types of devices—those that required the profile of the trench to be maintained and those that required the complete filling of trenches, i.e., a planar surface after regrowth. Low temperature Al0.22Ga0.78N growth was optimized and used as the marker layer for SEM. GaN deposition at a medium temperature of 950 °C and using N2 as carrier gas resulted primarily in growth on the (0001) plane, while the growth on the sidewalls was governed by the formation of slow growing semi-polar planes. This gave a conformal profile to the regrown GaN—useful for regrown GaN interlayer based vertical trench MOSFETs. In contrast, high temperature (1150 °C) growth in H2 resulted in high lateral growth rates. The planar surface was achieved under these conditions—a very promising result for CAVET-type devices.

Agarwal, Anchal↗

High-gain monolithic 3D CMOS inverter using layered semiconductors

Here, we experimentally demonstrate a monolithic 3D integrated complementary metal oxide semiconductor (CMOS) inverter using layered transition metal dichalcogenide semiconductor N-channel (NMOS) and P-channel (PMOS) MOSFETs, which are sequentially integrated on two levels. The two devices share a common gate. Molybdenum disulphide and tungsten diselenide are used as channel materials for NMOS and PMOS, respectively, with an ON-to-OFF current ratio (I ON /I OFF ) greater than 106 and electron and hole mobilities of 37 and 236 cm 2 /Vs, respectively. The voltage gain of the monolithic 3D inverter is about 45 V/V at a supply voltage of 1.5 V and a gate length of 1 μm. This is the highest reported gain at the smallest gate length and the lowest supply voltage for any 3D integrated CMOS inverter using any layered semiconductor.

42 ENGINEERING↗

High temperature characteristics of nitric oxide annealed p-channel 4H-SiC metal oxide semiconductor field effect transistors

In this work, p-channel 4H-SiC MOSFETs were fabricated and analyzed at high temperature. It is demonstrated that nitridation of the gate oxide enables enhancement mode operation in these devices. Nitrogen incorporation at the 4H-SiC/SiO2 interface by nitric oxide annealing reduces the interface trap density energetically located in the lower half of the 4H-SiC bandgap, resulting in viable high temperature p-channel devices. In the 27–300 °C temperature range, the threshold voltage decreases with increasing temperature, consistent with the reduction of occupied interface traps at higher temperatures. The hole channel mobility is weakly temperature dependent under strong inversion conditions. Hall measurements support that above the threshold voltage, the mobility is limited by surface roughness scattering. In weaker inversion, the channel conductivity is limited by interface hole trapping and Coulomb scattering. In addition, high temperature bias stress measurements confirm a temperature activated hole trapping under negative gate bias, which requires further investigations.

Das, Suman (ORCID:0000000317146287)↗

Atomic-scale defects generated in the early/intermediate stages of dielectric breakdown in Si/SiO 2 transistors

In this study, electrically detected magnetic resonance and near-zero-field magnetoresistance measurements were used to study atomic-scale traps generated during high-field gate stressing in Si/SiO 2 MOSFETs. The defects observed are almost certainly important to time-dependent dielectric breakdown. The measurements were made with spin-dependent recombination current involving defects at and near the Si/SiO 2 boundary. The interface traps observed are P b0 and P b1 centers, which are silicon dangling bond defects. The ratio of P b0 /P b1 is dependent on the gate stressing polarity. Electrically detected magnetic resonance measurements also reveal generation of E' oxide defects near the Si/SiO 2 interface. Near-zero-field magnetoresistance measurements made throughout stressing reveal that the local hyperfine environment of the interface traps changes with stressing time; these changes are almost certainly due to the redistribution of hydrogen near the interface.

42 ENGINEERING↗

R&D Towards Cryogenic Optical Links

A number of critical active and passive components of optical links have been tested at 77 K or lower temperatures, demonstrating potential development of optical links operating inside the liquid argon time projection chamber (LArTPC) detector cryostat. A ring oscillator, individual MOSFETs, and a high speed 16:1 serializer fabricated in a commercial 0.25-{micro}m silicon-on-sapphire CMOS technology continued to function from room temperature to 4.2 K, 15 K, and 77 K respectively. Three types of laser diodes lase from room temperature to 77 K. Optical fibers and optical connectors exhibited minute attenuation changes from room temperature to 77 K.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

2D materials advances: from large scale synthesis and controlled heterostructures to improved characterization techniques, defects and applications

The rise of two-dimensional (2D) materials research took place following the isolation of graphene in 2004. These new 2D materials include transition metal dichalcogenides, mono-elemental 2D sheets, and several carbide- and nitride-based materials. The number of publications related to these emerging materials has been drastically increasing over the last five years. Thus, through this comprehensive review, we aim to discuss the most recent groundbreaking discoveries as well as emerging opportunities and remaining challenges. This review starts out by delving into the improved methods of producing these new 2D materials via controlled exfoliation, metal organic chemical vapor deposition, and wet chemical means. Here we look into recent studies of doping as well as the optical properties of 2D materials and their heterostructures. Recent advances towards applications of these materials in 2D electronics are also reviewed, and include the tunnel MOSFET and ways to reduce the contact resistance for fabricating high-quality devices. Finally, several unique and innovative applications recently explored are discussed as well as perspectives of this exciting and fast moving field.

36 MATERIALS SCIENCE↗

Designing Ferroelectric Field-Effect Transistors Based on the Polarization-Rotation Effect for Low Operating Voltage and Fast Switching

The effect of polarization rotation on the performance of metal-oxide-semiconductor field-effect transistors is investigated with a Landau-Ginzburg-Devonshire theory-based model. In this analytical model, the depolarization field, polarization rotations, and electrostatic properties of the doped silicon substrate are considered to illustrate the size effect of ferroelectric oxides and the stability of polarization in each direction. Based on this model, we provide guidance in designing electronic logic devices with low operating voltages and low active-energy consumption: First, we demonstrate that MOSFET operation could be achieved by polarization reorientation with a low operating voltage, if the thickness of the ferroelectric oxide is properly selected. Polarization reorientation can boost the surface potential of the silicon substrate, leading to a subthreshold swing S lower than 60mV/decade. We also demonstrate that, compared with polarization inversion, polarization rotation offers significant advantages, including a lower energy barrier and a wider range of transferability in nanoelectronic devices.

36 MATERIALS SCIENCE↗

Colloquium : Anomalous metals: Failed superconductors

The observation of metallic ground states in a variety of two-dimensional electronic systems poses a fundamental challenge for the theory of electron fluids. Here evidence is analyzed for the existence of a regime, called the “anomalous metal regime,” in diverse 2D superconducting systems driven through a quantum superconductor to metal transition by tuning physical parameters such as the magnetic field, the gate voltage in the case of systems with a metal-oxide semiconductor field-effect transistor (MOSFET) geometry, or the degree of disorder. The principal phenomenological observation is that in the anomalous metal, as a function of decreasing temperature, the resistivity first drops as if the system were approaching a superconducting ground state, but then saturates at low temperatures to a value that can be orders of magnitude smaller than the Drude value. The anomalous metal also shows a giant positive magnetoresistance. Thus, it behaves as if it were a “failed superconductor.” This behavior is observed in a broad range of parameters. It will be moreover exhibited, by theoretical solution of a model of superconducting grains embedded in a metallic matrix, that as a matter of principle such anomalous metallic behavior can occur in the neighborhood of a quantum superconductor to metal transition. Furthermore, it will be also argued that the robustness and ubiquitous nature of the observed phenomena are difficult to reconcile with any existing theoretical treatment and speculate about the character of a more fundamental theoretical framework.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Rapid Prototyping Techniques for Organic Direct-Bonded-Copper Power Modules

Organic Direct-Bonded-Copper (ODBC) is a novel packaging technology for power modules which allows higher flexibility in layout design. In this work, a set of rapid prototyping techniques are developed for ODBC modules based on a polyimide dielectric material. These techniques enable fast and low-cost fabrication of modules with 3-Dimensional (3D) layout features. An example half-bridge (HB) silicon carbide (SiC) metal oxide semiconductor field effect transistor (MOSFET) module is designed and prototyped using the proposed techniques aiming at ultra-low power loop inductance. Finite element analysis (FEA)-circuit co-simulations results and experimental results validate an approximately 0.71nH power loop inductance for the example module design.

36 MATERIALS SCIENCE↗

Bond Wire Damage Detection and State of Health Estimation of a 1200V, 900A Dual Pack IGBT Power Module using the RL-Equivalent Circuit

Electrical and environmental stresses are the two dominant contributors in aging and failure of power semiconductor devices. Insulated gate bipolar junction transistors (IGBTs) and metal-oxide semiconductor field effect transistors (MOSFETs) are two most commonly used switching devices in power converter circuits. A significant portion of research effort is given in inventing innovative methods to estimate the degradation and fatigue in these devices. Until today, no other existing techniques can determine the number of lifted bond wires and their locations in a live IGBT module, although this information is extremely helpful to understand the overall state of health of an IGBT power module. In this paper, we have proposed a reflectometry-based technique to overcome this hurdle. The RL-equivalent circuit to represent a bond wire has been developed for the device under test and simulated in CST Studio Suite to measure the reflection amplitudes. Experimental results were obtained using a prototype reflectometry hardware, and both the simulation and experimental results have been compared. These results prove that with these two sets of measurements, it is possible to locate the aged device inside a module and detect the number of bond wire lift-offs associated to that device.

30 DIRECT ENERGY CONVERSION↗

A Simple Control to Reduce Device Over-Voltage Caused by Non-Active Switch Loop in Three-Level ANPC Converters

With the development of wide band-gap (WBG) technology, the switching speed of power semiconductor devices increases, which makes circuits more sensitive to parasitics. For three-level active neutral point clamped (3L-ANPC) converters, the over-voltage caused by additional non-active switch loop can be an issue. This paper analyzes the multiple commutation loops in 3L-ANPC converter and summarizes the impact factors of the device over-voltage. The nonlinearity of the output capacitance of the device can significantly influence the over-voltage. A simple control without introducing additional hardware circuit or complex software algorithm is proposed to attenuate the effect of the nonlinear output capacitance. Multi-pulse test is conducted for a 3L-ANPC converter built with silicon carbide (SiC) MOSFETs. With the proposed control, the testing results show that the peak drain-source voltage of both active and non-active switches is reduced by more than 20% compared to the conventional control.

Gui, Handong↗

Soft Switching Over the Entire Line Cycle for a Quadruple Active Bridge DCX in a DC to Three-Phase AC Module

This paper is focused on a transformer-isolated quadruple active bridge (QAB) dc-dc converter loaded by three full-bridge dc-ac inverters. The QAB functions as a "DC trans-former" (DCX) in the dc-to-three-phase ac module. The QAB outputs provide time-varying power at twice the line frequency, which presents challenges in maintaining zero voltage switching (ZVS) on the secondary sides during low-power portions of the line cycle. It is shown how ZVS can be achieved in a phase, even at zero-power transfer, using a relatively small circulating current provided by the magnetizing inductance of the high-frequency transformer. The approach is particularly effective in high-voltage applications using SiC MOSFETs, where reductions in switching loss outweigh additional conduction losses due to the circulating currents. A detailed analysis of ZVS switching waveforms at the zero power transfer is presented, including effects of nonlinear device capacitances. Analytical expressions are given for the optimal values of the magnetizing inductance and dead times of the QAB primary and secondary bridges. The approach is verified by experimental results on a 600 V, 4 kW prototype, demonstrating greater than 98.5% efficiency from 1 kW to 4 kW, with a peak efficiency of 99.0%. Compared to conventionally operated prototype, a 54% reduction in total loss is achieved at rated power.

41 EE - Solar Energy Technologies Office (EE-4S)↗