Results for “SHAPE” — Page 33

NASA NTRS2018

Further Evaluation of Swept Wing Icing Scaling with Maximum Combined Cross Section Ice Shape Profiles

This study reports results from recent icing scaling tests conducted in the NASA Glenn Icing Research Tunnel (IRT) using recommended scaling methods that were developed for swept wing icing applications. The aluminum test articles used in this study were NACA 0012 Adjustable Sweep Airfoil Models. The reference and scale airfoils have a 36 inch and 15 inch chord measured normal to the leading edge, and a 60 inch and 24 inch span respectively. Reference tests were run with airspeeds of 100, 140.3 and 150 knot and MVD of 41.4, 44.4, 93 and 150 micron. All tests were set at 0⁰ angle of attack (AOA) and 30⁰ sweep angle. Results will be presented for stagnation freezing fractions ranging from 0.3 to 1.0. For non-dimensional reference & scale ice shape comparison, a new post-scanning ice shape digitization procedure was applied to extract 2-D "hand-tracing like" ice shape profiles, i.e. the Maximum Combined Cross Section or MCCS, at selected span-wise locations from the high fidelity 3-D scanned ice shapes obtained in the IRT. Preliminary assessment of ice shape comparison with MCCS showed that good scaling was achieved for the test conditions by using the recommended scaling methods developed for swept wing icing.

MCCS↗

NASA NTRS2019

Shape Sensing for Wings with Spars and Ribs Using Simulated Strain

Active trim shape control can be used to minimize error between target and actual aircraft trim shape during flight. Trim shape sensing for aircraft during flight is not only important for highly flexible aircraft, such as the National Aeronautics and Space Administration (NASA) Helios Prototype remotely piloted flying wing aircraft, but also for a delta-wing type aircraft, such as a supersonic commercial transport aircraft. A two-step theory utilizing distributed strain for a real-time shape sensing of a full three-dimensional structure has been introduced previously. This study focuses on the application of the two-step theory to finite element models of a wing with spars and ribs such as the X-59 QueSST aircraft (Lockheed Martin Corporation, Bethesda, Maryland), a tapered wing, a dihedral/anhedral wing, and a stiffened dihedral/anhedral wing. A finely meshed finite element structural model is desired to capture accurate curvature distributions along the neutral axes of the wing cross sections during pre-test analysis for shape sensing of a wing with ribs and spars. The two-step theory used in this study gives excellent deformation correlation with the MSC/NASTRAN (MSC Software, Newport Beach, California) results along the neutral axis for all test cases used in this study except the X-59 QueSST aircraft.

strain↗

NASA NTRSDate not supplied

Ice Shape Classification for Swept Wings

An important consideration for swept-wing ice shapes is the level of geometric fidelity required to accurately capture the aerodynamics. One way to help make the task of addressing this more manageable is to organize the ice shapes into a small number of classifications. These classifications are done by grouping similar ice shape geometries that also have similar iced wing aerodynamics. Ice shape classifications for airfoils are more mature and are reviewed as an example. Swept wing ice shape classifications are based on the well-established airfoil classifications and here five classifications are proposed: leading-edge roughness, streamwise ice, 3D leading-edge horn, highly 3D leading-edge horn and spanwise ridge. Recent data on swept wing icing aerodynamics is used to develop and support this classification. The development, or suppression, of the leading-edge separation vortex on swept wings without a leading-edge device is seen to be key in the classification of the highly 3D leading-edge horn.

Aircraft icing↗

NASA NTRS2021

Meta-aerogels: Auxetic Shape-memory Polyurethane Aerogels

Shape-memory poly(isocyanurate-urethane) (PIR-PUR) aerogels are low-density monolithic nanoporous solids that remember and return to their permanent shape through a heating actuation step. Herein, through structural design at the macro scale, the shape-memory response is augmented with an auxetic effect manifested by a negative Poisson’s ratio of approximately -0.8 at 15% compressive strain. Thus, auxetic shape-memory PIR-PUR monoliths experience volume contraction upon compression at a temperature above the glass transition temperature of the base polymer (Tg ~ 30 °C), and they can be stowed indefinitely in that temporary shape by cooling below Tg. By heating back above Tg, the compressed/shrunk form expands back to their original shape/size. This technology is relevant to a broad range of industries spanning the commercial, aeronautical, and aerospace sectors. The materials are referred to as meta-aerogels and their potential applications include minimally invasive medical devices, soft robotics, and in situations where volume is at a premium, as for example for storage of deployable space structures and planetary habitats during transport to the point of service.

Sadeq Malakooti↗

NASA NTRS2022

A Comparative Evaluation of Snowflake Particle Shape Estimation Techniques Used By the Precipitation Imaging Package (PIP), Multi-Angle Snowflake Camera (MASC), and Two-Dimensional Video Disdrometer (2DVD)

Measurements of snowflake particle shape are important for studying snow microphysics. While a number of instruments exist that are capable of measuring particle shape, this study focuses on the measurement techniques of three digital video disdrometers: the Precipitation Imaging Package (PIP), the Multi-Angle Snowflake Camera (MASC), and the Two-Dimensional Video Disdrometer (2DVD). To gain a better understanding of the relative strengths and weaknesses of these instruments and to provide a foundation upon which comparisons can be made between studies using data from different instruments, we perform a comparative analysis of the shape measurement algorithms employed by each of the three instruments by applying the algorithms to snowflake images captured by PIP during the ICE-POP 2018 field campaign. Our analysis primarily focuses on the measurement of the aspect ratio of either the particle itself, in the case of PIP and MASC, or of the particle bounding box, in the case of PIP and 2DVD. Both PIP and MASC use shape-fitting algorithms to measure aspect ratio. While our analysis of the MASC aspect ratio suggests that the measurements are reliable, our findings indicate that both the ellipse and rectangle aspect ratios produced by PIP underperformed considerably due to the shortcomings of the PIP shape-fitting techniques. We also demonstrate that reliable measurements of aspect ratio can be retrieved from PIP by reprocessing the raw PIP images using either the MASC ellipse-fitting algorithm or a tensor-based ellipse-fitting algorithm. Because of differences in instrument design, 2DVD produces measurements of particle horizontal and vertical extent rather than length and width. Furthermore, the 2DVD measurements of particle horizontal extent can be contaminated by horizontal particle motion. Our findings indicate that, although the correction technique used to remove the horizontal motion contamination performs remarkably well with snowflakes despite being designed for use with raindrops, the 2DVD measurements of particle horizontal extent are less reliable than those measured by PIP.

Charles N Helms↗

NASA NTRS2024

3D Scanning System to Assess Gravity-Dependent Body Shape Changes

The human body shows unique physiological and morphological changes when exposed to different gravity conditions, including muscle atrophy, fluid shift, spinal elongation, and body posture adjustments. Such changes need to be incorporated for human-system integration in the vehicle habitat, garment, and spacesuit designs, as inaccurate body measurements can result in suboptimal crew protection that can potentially decrease injury tolerance. However, the traditional linear measurements, such as stature, segment lengths or circumferences measured using a caliper or tape measure, often show limited consistency and are unable to capture the nonlinear characteristics of the human body. While 3D body scanning can provide significant advantages over linear measurements, the technologies have not been fully developed or customized for in-flight scanning. For ground laboratory use, several different scanner types are commercially available. However, in-flight scanning requires additional technical considerations, such as minimal scan time, simplified calibration, and sufficient capture volume. This work aims to develop a prototype 3-D body scanning system that is customized for in-flight use to scan crewmembers, with the configuration and performance optimized for detecting known gravity-dependent body shape and posture changes. A hardware system will be custom built using a network of commercial off-the-shelf 3D sensors. The sensor parameters and settings will be optimized to detect the targeted body shape changes, specifically using body manikins of which the shape and size are iteratively permuted to simulate the known changes by fluid shift and spinal elongation. The capture volume will be also matched for a range of body sizes from a 1st percentile female to 99th percentile male. Unintentional body motions or floating in microgravity will be also simulated and incorporated. A data acquisition software will be developed for efficient in-flight operations with minimal overhead and easy-to-use user interface. A simplified calibration procedure will be designed for robust scanning against frequent vibration or unexpected sensor position shifts. The system will be tested in the ground laboratory for accuracy and reliability against a reference scanning system. New anthropometry measurements will be also identified to sensitively capture the gravity dependent body shape changes, in addition to the traditional anthropometry measurements. A novel landmark-based technique will be tested for consistent anthropometry measurements across posture variations. If successfully developed and deployed, the new system is expected to provide previously unavailable body shape and size data from different gravitational environments, including 0-g, 1/6-g, and 1-g. Such data can improve suit fit, habitat design, exercise efficacy quantification and sizing of orthostatic intolerance garments.

K H Kim↗

NASA NTRS2024

3D Scanning System to Assess Gravity-Dependent Body Shape Changes

The human body shows unique physiological and morphological changes when exposed to different gravity conditions, including muscle atrophy, fluid shift, spinal elongation, and body posture adjustments. Such changes need to be incorporated for human-system integration in the vehicle habitat, garment, and spacesuit designs, as inaccurate body measurements can result in suboptimal crew protection that can potentially decrease injury tolerance. However, the traditional linear measurements, such as stature, segment lengths or circumferences measured using a caliper or tape measure, often show limited consistency and are unable to capture the nonlinear characteristics of the human body. While 3D body scanning can provide significant advantages over linear measurements, the technologies have not been fully developed or customized for in-flight scanning. For ground laboratory use, several different scanner types are commercially available. However, in-flight scanning requires additional technical considerations, such as minimal scan time, simplified calibration, and sufficient capture volume. This work aims to develop a prototype 3-D body scanning system that is customized for in-flight use to scan crewmembers, with the configuration and performance optimized for detecting known gravity-dependent body shape and posture changes. A hardware system will be custom built using a network of commercial off-the-shelf 3D sensors. The sensor parameters and settings will be optimized to detect the targeted body shape changes, specifically using body manikins of which the shape and size are iteratively permuted to simulate the known changes by fluid shift and spinal elongation. The capture volume will be also matched for a range of body sizes from a 1st percentile female to 99th percentile male. Unintentional body motions or floating in microgravity will be also simulated and incorporated. A data acquisition software will be developed for efficient in-flight operations with minimal overhead and easy-to-use user interface. A simplified calibration procedure will be designed for robust scanning against frequent vibration or unexpected sensor position shifts. The system will be tested in the ground laboratory for accuracy and reliability against a reference scanning system. New anthropometry measurements will be also identified to sensitively capture the gravity dependent body shape changes, in addition to the traditional anthropometry measurements. A novel landmark-based technique will be tested for consistent anthropometry measurements across posture variations. If successfully developed and deployed, the new system is expected to provide previously unavailable body shape and size data from different gravitational environments, including 0-g, 1/6-g, and 1-g. Such data can improve suit fit, habitat design, exercise efficacy quantification and sizing of orthostatic intolerance garments.

K H Kim↗

DOE OSTI2015

Shape memory polymer foams for endovascular therapies

A system for occluding a physical anomaly. One embodiment comprises a shape memory material body wherein the shape memory material body fits within the physical anomaly occluding the physical anomaly. The shape memory material body has a primary shape for occluding the physical anomaly and a secondary shape for being positioned in the physical anomaly.

36 MATERIALS SCIENCE↗

DOE OSTI2017

Shape memory polymer foams for endovascular therapies

A system for occluding a physical anomaly. One embodiment comprises a shape memory material body wherein the shape memory material body fits within the physical anomaly occluding the physical anomaly. The shape memory material body has a primary shape for occluding the physical anomaly and a secondary shape for being positioned in the physical anomaly.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Performance of first prototype multi-cell low-surface-field shape cavity

The idea of cavity shaping for higher ultimate acceleration gradients has been proposed for some time, Low Loss/Ichiro and Re-entrant being examples, both seeking a lower Hpk/Eacc at the expense of a higher Epk/Eacc. While experimental verification in single-cell cavities of those shapes was very successful including the record gradient of 59 MV/m, pushing multi-cell cavities of those shapes to higher gradients was prevented by field emission. The Low-Surface-Field (LSF) shape seeks not only a lower Hpk/Eacc but also a lower Epk/Eacc, therefore it has the advantage of raising ultimate gradient at reduced field emission. The first multi-cell LSF shape prototype cavity was built using the standard forming and welding techniques. RF tests have been carried out, following standard ILC TDR baseline surface processing and treatment recipe. Three out of five cells achieved Hpk values corresponding to Eacc 50 MV/m. The current limit is the field emission in end cells. Instrumented testing following end-cell wiping and HPR with larger nozzles is in progress. We will present detailed experimental results and preparation procedures.

Geng, R.-L.↗

DOE OSTI2020

Shape memory polymer foams for endovascular therapies

A system for occluding a physical anomaly. One embodiment comprises a shape memory material body wherein the shape memory material body fits within the physical anomaly occluding the physical anomaly. The shape memory material body has a primary shape for occluding the physical anomaly and a secondary shape for being positioned in the physical anomaly.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Shape memory polymer foams for endovascular therapies

A system for occluding a physical anomaly. One embodiment comprises a shape memory material body wherein the shape memory material body fits within the physical anomaly occluding the physical anomaly. The shape memory material body has a primary shape for occluding the physical anomaly and a secondary shape for being positioned in the physical anomaly.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Apparatus and method for shaped waveform interrogation

Described are an apparatus, computer program product, and associated methods for shaped waveform acoustic interrogation of substances and materials to determine one or more properties of the materials or substances. In some embodiments, a shaped waveform is formed by summing two or more different waveforms and an acoustic wave is generated according to the shaped waveform. The acoustic wave is transmitted by one or more transmitting transducers through the substance or material and received by one or more receiving transducers. The shaped waveform acoustic wave can have a duration or a period that is less than about 20 μs and can comprise predetermined frequency content. Characteristics of the shaped waveform acoustic wave, as received at the receiving transducer(s), including characteristics such as amplitude, frequency, time of flight, etc., can be associated with said one or more properties of the substance or material to provide for real-time monitoring of these properties.

Sinha, Dipen N.↗

DOE OSTI2016

Size, shape and flow characterization of ground wood chip and ground wood pellet particles

Size, shape and density of biomass particles influence their transportation, fluidization, rates of drying and thermal decomposition. Pelleting wood particles increases the particle density and reduces the variability of physical properties among biomass particles. In this study, pine chips prepared for pulping and commercially produced pine pellets were ground in a hammer mill using grinder screens of 3.2, 6.3, 12.7 and 25.4mmperforations. Pellets consumed about 7 times lower specific grinding energy than chips to produce the same size of particles. Grinding pellets produced the smaller particles with narrower size distribution than grinding chips. Derived shape factors in digital image analysis showed that chip particles were rectangular and had the aspect ratios about one third of pellet particles. Pellet particles were more circular shape. The mechanical sieving underestimated the actual particle size and did not represent the size of particles correctly. Instead, digital imaging is preferred. Angle of repose and compressibility tests represented the flow properties of ground particles. Pellet particles made a less compacted bulk, had lower cohesion and did flow easier in a pile of particles. In conclusion, particle shape affected the flow properties more than particle size

09 BIOMASS FUELS↗

DOE OSTI2025

Laser-Modulation-Driven X-Ray Pulse Shaping in Regenerative Amplifier Free-Electron Lasers

In this Letter, we present a robust method for generating custom-shaped, coherent hard x-ray pulses in regenerative amplifier free-electron lasers (RAFELs) using laser-induced energy modulation of the electron beam. A temporally shaped optical modulation imprints an optical-wavelength energy pattern on the beam, which interacts with the recirculated seed in the x-ray cavity to generate spectral sidebands. These sidebands lie outside the Bragg reflection bandwidth and are extracted as out-coupled radiation, while the seed is retained for continued amplification, enabling a novel mechanism for both output coupling and pulse shaping. Furthermore, this approach allows deterministic control over the spectral and temporal properties of the emitted x-rays, including multicolor generation, twin-pulse structures, pulse duration tuning, and complex temporal waveforms. Importantly, it does not require modification of the RAFEL cavity or optics and is fully compatible with high-repetition-rate operation, offering a practical pathway to deliver coherent, shaped, and on-demand x-ray pulses for advanced time-resolved and nonlinear x-ray science.

Free-electron lasers↗

DOE OSTI2022

Selective Heating Through Y-Junction Waveguide Designed by Acoustic Shape Optimization

Unlike phononic crystals or systems designed by topology optimization, waveguides designed by shape optimization do not have voids or internal defects, making the fabrication process more suitable for additive manufacturing. By designing a Y-junction waveguide through shape optimization, an ultrasonic wave can be controlled so that it propagates to a predetermined location just by adjusting its frequency. These demultiplexed ultrasonic waves can be used to transport signals or stimulate nearby materials. As an example, the ultrasonic wave is converted to heat at different locations, which can be applied to mechanisms that can take advantage of heating. First, shape optimization is performed on a cylindrical structure to selectively propagate ultrasonic waves of a particular frequency while attenuating others, which is analyzed through a finite element model. The numerical study results are compared with experimental measurements from samples fabricated through additive manufacturing methods. After verifying the concept, the Y-junction waveguide is fabricated to demultiplex the wave and selectively heat different locations. Here the results show that the method of combining shape optimization with additive manufacturing is exceptionally simple and capable of demultiplexing ultrasonic waves, which can replace complex electrical components with single-material waveguides.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Modifiers versus Channels: Creating Shape-Selective Catalysis of Metal Nanoparticles/Porous Nanomaterials

Shape-selective catalysis is of great research interest for its key role in chemical synthesis. Porous nanomaterials with uniform pore structures, have been proven as ideal supports for metal nanoparticles (MNPs) to generate efficient shape-selective catalysis. However, many widely used commercial irregular porous nanomaterials usually face the challenge to realize satisfactory shape selectivity due to the lack of molecular sieving structures. In this work, we report a concept of creating shape selectivity in MNPs/porous-MNPs using appropriate modifiers. The remained MNPs within the porous nanomaterials can cooperate with the channels to generate selectivity. Such strategy not only applies to regular porous nanomaterials (metal-organic frameworks, zeolites, etc.), but also can be extended to irregular porous nanomaterials (active carbon, P25, etc.). Potentially, the matching among different MNPs, corresponding modifiers and porous nanomaterials makes our strategy promising for wide applications in selective catalytic systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Yet another parameter-free shape optimization method

The use of node coordinates as design variables in shape optimization offers a larger design space than computer-aided design (CAD)-based shape parameterizations. It also allows for the optimization of legacy designs, i.e., a finite element mesh from an existing design can be readily optimized to meet new performance requirements without involving a CAD model. However, it is well known that the node coordinate parameterization method is fraught with numerical difficulties, which makes it impractical to use. This has led to several of “parameter-free” shape optimization methods that seek the advantages and avoid the pitfalls of the naïve node coordinate parameterization method. These methods come in two main varieties: sensitivity filtering (or gradient smoothing) and consistent filtering. The latter is analogous to the density filter method used in topology optimization (TO). In this work, we use the PDE filter from TO and energy-based filters to implement consistent shape optimization filtering schemes easily and efficiently. Numerical experiments demonstrate that consistent methods are more robust than sensitivity filtering methods.

42 ENGINEERING↗