Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Agreements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 577 records · Page 32
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Extending the capillary wave model to include the effect of bending rigidity: X-ray reflectivity and diffuse scattering

The surface roughness of a thin film at a liquid interface exhibits contributions of thermally excited fluctuations. This thermal roughness depends on temperature (𝑇), surface tension (𝛾), and elastic material properties, specifically the bending modulus (𝜅) of the film. A nonzero 𝜅 suppresses the thermal roughness at small length scales compared to an interface with zero 𝜅, as expressed by the power spectral density of the thermal roughness. The description of the x-ray scattering of the standard capillary wave model (CWM), which is valid for zero 𝜅, is extended to include the effect of 𝜅. The extended CWM (eCWM) provides a single analytical form for both the specular x-ray reflectivity (XRR) and the diffuse scattering around the specular reflection, and recovers the expression of the CWM at its zero 𝜅 limit. This theoretical approach enables the use of single-shot grazing incidence x-ray off-specular scattering (GIXOS) measurements for characterizing the structure of thin films on a liquid surface. The eCWM analysis approach decouples the thermal roughness factor from the surface scattering signal, providing direct access to the intrinsic surface-normal structure of the film and its bending modulus. Moreover, the eCWM facilitates the calculation of reflectivity at any desired resolution (pseudo-XRR approach). The transformation into pseudo-XRR provides the benefit of using widely available XRR software to perform GIXOS analysis. The extended range of the vertical scattering vector (𝑄 𝑧 ) available with the GIXOS pseudo-XRR approach allows for a higher spatial resolution than with conventional XRR. Experimental results are presented for various lipid systems, showing strong agreement between conventional specular XRR and pseudo-XRR methods. This agreement validates the proposed approach and highlights its utility for analyzing soft, thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Structure of ice VII with Hirshfeld atom refinement

In the refinement of the crystal structures of ice, the best results obtained so far have been with neutron diffraction because the most troublemaking aspects are the hydrogen atoms. In nine out of twenty ice structures, the hydrogen atoms are disordered, which makes proper refinement more difficult. In our previous paper describing the structure of ice VI we proved that, using Hirshfeld atom refinement (HAR) based on synchrotron X-ray data, it is possible to obtain results comparable with those from neutron experiments. In this work, we investigate another structure of high-pressure disordered ice, cubo-ice (ice VII). Single crystals of cubo-ice were grown under pressure in diamond anvil cells. X-ray diffraction measurements were conducted at a synchrotron source facility (APS, University of Chicago, USA) as well as on our regular in-house laboratory diffractometer with Ag radiation. The data collected were further refined with HAR. Comparison of the structural parameters obtained with those derived from neutron diffraction showed very good agreement in terms of bond lengths and fairly good agreement in terms of hydrogen atom ADPs. We were also able to perform unconstrained refinements with various split-atom models.

Chemistry↗
DOE OSTI2022

New Hybrid Model for Evaluating the Frequency-Dependent Leakage Inductance of a Variable Inductance Transformer (VIT)

Skin and proximity effects can cause a significant drop in the effective leakage inductance of a transformer when the operating frequency is increased. Although the magnetic image method-based double-2-D model can calculate the lowfrequency leakage inductance with sufficient accuracy, it is inherently a frequency-independent model. While Dowell’s 1-D model uses frequency-dependent relations to account for both skin and proximity effects, its accuracy is severely affected by the assumed winding geometry. In this paper, a hybrid model is proposed that uses superposition to combine a modified Dowell’s model with the double-2-D model. The proposed model is investigated on a variable inductance transformer (VIT)—a partially-filled transformer whose leakage inductance can be varied by moving one of the windings mechanically. The frequency-dependent leakage inductances of the VIT evaluated using the hybrid model are in excellent agreement with the corresponding finite element method (FEM) simulated and experimentally measured values, thereby validating the proposed hybrid model.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Penetration Through Slots in Cylindrical Cavities Operating at Fundamental Cavity Modes

In this article, we examine the coupling into an electrically short azimuthal slot on a cylindrical cavity operating at fundamental cavity modal frequencies. We first develop a matched bound formulation through which we can gather information for maximum achievable levels of interior cavity fields. Actual field levels are below this matched bound; therefore, we also develop an unmatched formulation for frequencies below the slot resonance to achieve a better insight on the physics of this coupling. Good agreement is observed between the unmatched formulation, full-wave simulations, and experimental data, providing a validation of our analytical models. We then extend the unmatched formulation to treat an array of slots, found again in good agreement with full-wave simulations. These analytical models can be used to investigate ways to mitigate electromagnetic interference and electromagnetic compatibility effects within cavities.

42 ENGINEERING↗
DOE OSTI2021

Simulation and Modeling of Time-Resolved X-Ray Detector for the Saturn Accelerator

In this work, we present the technology-aided computer design (TCAD) device simulation and modeling of a silicon p-i-n diode for detecting time-dependent X-ray radiation. We show that the simulated forward and reverse breakdown current–voltage characteristics agree well with the measured data under nonradiation environment by only calibrating carrier lifetimes for the forward bias case and avalanche model critical fields for the reverse bias condition. Using the calibrated parameters and other nominal material properties, we simulated the radiation responses of the p-i-n diode and compared with experimental data when the diode was exposed to X-ray radiation at Sandia’s Saturn facility and the Idaho State University (ISU) TriMeV facility. For Saturn’s Gaussian dose-rate pulses, we show three findings from TCAD simulations. First, the simulated photocurrents are in excellent agreement with the measured data for two dose-rate pulses with peak values of 1.16×10 10 and 1.88×10 10 rad(Si)/s. Second, the simulation results of high dose-rate pulses predict increased delayed photocurrents with longer time tails in the diode electrical responses due to excess carrier generation. Third, simulated peak values of diode radiation responses versus peak dose rates at different bias conditions provide useful guidance to determine the dose-rate range that the p-i-n diode can reliably detect in experiment. For TriMeV’s non-Gaussian dose-rate pulse, our simulated diode response is in decent agreement with the measured data without further calibration. We also studied the effects of device geometry, recombination process, and dose-rate enhancement via TCAD simulations to understand the higher measured response in the time after the peak dose-rate radiation for the p-i-n diode exposed to TriMeV irradiation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Rainfall manipulation experiments as simulated by terrestrial biosphere models: Where do we stand?

Changes in rainfall amounts and patterns have been observed and are expected to continue in the near future with potentially significant ecological and societal consequences. Modelling vegetation responses to changes in rainfall is thus crucial to project water and carbon cycles in the future. In this study, we present the results of a new model-data intercomparison project, where we tested the ability of 10 terrestrial biosphere models to reproduce the observed sensitivity of ecosystem productivity to rainfall changes at 10 sites across the globe, in nine of which, rainfall exclusion and/or irrigation experiments had been performed. The key results are as follows: (a) Inter-model variation is generally large and model agreement varies with timescales. In severely water-limited sites, models only agree on the interannual variability of evapotranspiration and to a smaller extent on gross primary productivity. In more mesic sites, model agreement for both water and carbon fluxes is typically higher on fine (daily–monthly) timescales and reduces on longer (seasonal–annual) scales. (b) Models on average overestimate the relationship between ecosystem productivity and mean rainfall amounts across sites (in space) and have a low capacity in reproducing the temporal (interannual) sensitivity of vegetation productivity to annual rainfall at a given site, even though observation uncertainty is comparable to inter-model variability. (c) Most models reproduced the sign of the observed patterns in productivity changes in rainfall manipulation experiments but had a low capacity in reproducing the observed magnitude of productivity changes. Models better reproduced the observed productivity responses due to rainfall exclusion than addition. (d) All models attribute ecosystem productivity changes to the intensity of vegetation stress and peak leaf area, whereas the impact of the change in growing season length is negligible. Finally, the relative contribution of the peak leaf area and vegetation stress intensity was highly variable among models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Melting rate correlation with batch properties and melter operating conditions during conversion of nuclear waste melter feeds to glasses

The rate of conversion of nuclear waste melter feed to glass is affected by the selection of melter feed materials and by melter design and operation. The melting rate correlation (MRC) is an equation that relates the glass production rate with two types of variables: (1) feed and melt properties: conversion heat, cold-cap bottom temperature, and glass melt viscosity; and (2) melter design and operation parameters: melter geometry, melter operating temperature, and gas bubbling rate. The MRC shows good agreement for an extended melting-rate data set of high-level waste (HLW) melter feeds and a data set generated for low-activity waste (LAW) melter feeds. Laboratory observation of heated melter feed samples is often used to assess the cold-cap bottom temperature of HLW melter feeds (moderately foaming feeds), but this technique appears inadequate for LAW melter feeds (vigorously foaming feeds). For LAW feeds, an adequate assessment of the cold-cap bottom temperature was achieved using evolved gas analysis, which allows identification of the collapse of primary foam for oxidized feeds. This assessment shows that the cold-cap bottom temperature for vigorously foaming LAW feeds is higher than that for moderately foaming HLW feeds. When the results of MRC are compared, LAW feeds are generally less sensitive to the bubbling rate and melt viscosity, and more sensitive to the cold-cap bottom temperature than HLW feeds. The MRC qualifies as a promising tool to support the selection of melter feed materials and melter operating conditions, which is determined from expensive independent scaled melter experiments, and sophisticated mathematical models.

Lee, Seung Min↗
DOE OSTI2022

Tailoring critical Al concentration to form external Al 2 O 3 scale on Ni–Al alloys by computational approach

Abstract Nickel (Ni)‐based superalloys for high‐temperature applications are often designed to form a continuous and slow‐growing oxide scale by adding Al and Cr and other beneficial elements. In the present work, the critical Al concentration in Ni–Al alloys needed to establish an α‐Al 2 O 3 scale in contrast to internal oxide formation is predicted as a function of temperature by means of the CALPHAD approach coupled with models in the literature, which account for the thermodynamics and kinetics of oxidation. The present thermodynamic remodeling of the Ni–O system results in a better agreement with experimental data of oxygen solubility in Ni at high temperatures. The oxygen solubility is combined with kinetic parameters to determine oxygen permeability in Ni, and the critical Al concentration needed to establish an α‐Al 2 O 3 scale at a given exposure temperature. Good agreement is found with available experimental data for both oxygen permeability and critical Al concentration, indicating the capacity of the CALPHAD approach to tailor oxidation resistance for materials of interest using thermodynamic and kinetic knowledge.

Ross, Austin↗
DOE OSTI2020

Experimental and Numerical Investigation of a Miniature Additively Manufactured Vortex Tube

Ranque–Hilsch vortex tubes are simple devices that can produce a cooling effect using compressed air. A key advantage of vortex tubes is the lack of moving solid parts; however, their efficiencies are relatively low. The present study focuses on the development of a miniature variable-diameter tube using additive manufacturing. A metal-based 3D printing technique was utilized to fabricate this vortex tube monolithically. Computational fluid dynamics simulations employing software STAR-CCM + with a compressible Reynolds-Averaged Navier–Stokes (RANS) approach and the elliptic-blending lag k-epsilon turbulence model have been applied to model thermofluid processes inside the vortex tube, to good agreement with the experiment. In conclusion, a temperature decrease of 13.3 °C and a cooling power of approximately 4 W were experimentally achieved with a pressure ratio of 4 in the air at normal conditions. This result shows promise for the goal of utilizing additive manufacturing to design and build complex-geometry vortex tubes intended for use with cryogenic fluids.

08 HYDROGEN↗
DOE OSTI2020

Experiments and Simulations on the Turbulent, Rarefaction Wave Driven Rayleigh–Taylor Instability

Experiments were performed to observe the growth of the turbulent, Rayleigh–Taylor unstable mixing layer generated between air and SF 6 , with an Atwood number of A=(ρ 2 –ρ 1 )/(ρ 2 +ρ 1 ) = 0.64, where ρ 1 and ρ 2 are the densities of air and SF 6 , respectively. A nonconstant acceleration with an average value of 2300g 0 , where g 0 is the acceleration due to gravity, was generated by interaction of the interface between the two gases with a rarefaction wave. Three-dimensional, multimode perturbations were generated on the diffuse interface, with a diffusion layer thickness of δ = 3.6 mm, using a membraneless vertical oscillation technique, and 20 experiments were performed to establish a statistical ensemble. The average perturbation from this ensemble was extracted and used as input for a numerical simulation using the Lawrence Livermore National Laboratory (LLNL) Miranda code. Good qualitative agreement between the experiment and simulation was observed, while quantitative agreement was best at early to intermediate times. Several methods were used to extract the turbulent growth constant α from experiments and simulations while accounting for time varying acceleration. Experimental, average bubble and spike asymptotic self-similar growth rate values range from α = 0.022 to α = 0.032 depending on the method used, and accounting for variable acceleration. Values found from the simulations range from α = 0.024 to α = 0.041. Here, the values of α measured in the experiments are lower than what are typically measured in the literature but are more in line with those found in recent simulations.

42 ENGINEERING↗
DOE OSTI2022

Experimental and Numerical Study on the Effect of Annular Combustor Design on Thermal Uniformity Jet in Crossflow

Abstract Non-uniformity of the exit flow temperature represents one of the significant damages to gas-turbine components, particularly turbine blades. This may occur in the course of gas-turbine operation. This paper aims to provide passive techniques by modifying the combustor design rather than changing the flow parameters to improve the thermal uniformity and turbine blades to reduce thermal stresses and increase turbine blades’ life span. An acceptable agreement between the numerical and experimental results has been achieved, and the agreement includes the velocity and temperature profile. Four different angles have been tested numerically and experimentally with a maximum error of 5% at two different Reynolds numbers. Designing the outer combustor surface with a 45-deg angle bend can give a more uniform temperature distribution of 37% higher than the basic design with only a 0.5% higher pressure drop.

Energy & Fuels↗
DOE OSTI2022

Characterization of the Finite Element Computational Fluid Dynamics Capabilities in the Multiphysics Object Oriented Simulation Environment

We report the multiphysics object-oriented simulation environment (moose) is a code package that couples a variety of physics modules, allowing for highly accessible multiphysics simulations. The physics modules include a finite element Navier–Stokes (N–S) module that is designed to solve laminar fluid dynamics problems. The usage of this module in multiple recent studies coupled with the growing interest in moose for usage in nonlight water reactor safety studies by the Nuclear Regulatory Commission (NRC) prompted the authors to investigate the computational fluid dynamics capabilities of moose. A two-dimensional laminar flow past a circular cylinder scenario is simulated in the moose framework to investigate the effectiveness of the N–S module. Simulations assumed an unsteady laminar flow with a Reynolds number of 200. To verify the results from moose, similar simulations were conducted using the well-utilized simulation of turbulent flow in arbitrary regions—computational continuum mechanics C++ (star-ccm + ) finite volume code. Results from both codes are also compared to some results from literature. Velocity and pressure profiles of both transient simulations were compared. The numerical and input errors in moose are also visualized with contour plots to qualitatively understand the evolution of the errors across time and space. The comparisons between moose and star-ccm + showed nearly perfect agreement between the codes for velocity and pressure, especially after the development of the vortex street in later time-steps. The force coefficients showed excellent agreement after the development of the vortex street, but demonstrated notable discrepancies prior to the vortex street development, which is likely due to how each code simulated the approach to the vortex street in earlier time-steps.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Quantitative Systems Modeling for Critical Infrastructure Predictions in Climate Change: A National Defense Framework

Any national defense is dependent on the efficacy of the available physical infrastructure. Whatever degrades infrastructure, structurally, physically, architecturally, or esthetically, is of interest to the nation. Climate change is now a major significant factor of interest impinging on national critical infrastructure. The devastating effects of climate change have increasing pervasiveness throughout the world. The impact on critical infrastructure is of particular interest to researchers. In consonance with ASCE-ASME's special issue on critical infrastructure protection and resilience, this paper presents a systems-modeling approach for critical infrastructure and predictions in relation to climate change agreements in COP26. The paper addresses high-level critical systems-based assessment of the social, legal, economic, and technical nuances impinging on the viability of COP26 agreements. The paper was written using a multinational collaboration approach. In conclusion, the specific focus of national defense is used as the backdrop for the methodology of the paper.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Attached Jet Velocity Profiles in Mixing Tanks

Free jets have been studied in detail over much of the last century, but the theory for offset and attached jets remains incomplete. Attached jets differ from free jets in that they lose momentum to nearby surfaces, attenuating their velocities. The velocity profiles of free circular jets are nearly Gaussian, with quantitative mathematical descriptions derived from first principles by Goertler and Tollmien (Rajaratnam, 1976). In contrast, mathematical descriptions of three-dimensional attached jets from circular nozzles remain much less mature. Agelin-Chaab and Tachie (2011) used particle imaging velocimetry of a three-dimensional attached jet to show that the scaled velocity decays with scaled distance from the nozzle with a power law exponent between -1.15 and -1.21, which is larger in magnitude than that of a free jet. However, quantitative analytical expressions for the velocity profiles of attached jets similar to those of free jets remain elusive. This paper addresses this critical gap. Here we evaluate the velocity profiles of three-dimensional offset jets emerging from circular nozzles that that become attached jets. These jets lose momentum due to interactions with nearby surfaces and are important to evaluating flows in mixing vessels and to suspending solids and trapped gases in radioactive waste tanks. Despite the importance of attached jets, prior insight has been purely experimental, limited to overly simplistic analytical models, or restricted to computationally expensive computational fluid dynamics case studies. We compare the expression of Verhoff (1963) to experimental results to find reasonable quantitative agreement. As stated by Agelin-Chaab and Tachie (2011), “detailed velocity measurements of 3D offset jets are rare.” Such remains the case. This study adds to the literature by providing information at two additional Reynolds numbers (1.43 106 and 1.87 106) and evaluating simple but accurate expressions for velocity profiles. These Reynolds numbers are an order of magnitude higher than prior reports. The semi-empirical stream wise velocity profile perpendicular to the surface proposed by Verhoff (1963) is in approximate agreement with these velocity profiles, which is surprising because these attached jets are three-dimensional instead of two-dimensional as evaluated by Verhoff. However, additional work is necessary to fully describe these profiles quantitatively.

jet, attached jet, offset jet↗
DOE OSTI2021

Hybrid Improved Empirical Mode Decomposition and Artificial Neural Network Model for the Prediction of Critical Heat Flux (CHF)

Three Hybrid artificial neural network (ANN) models namely radial basis function (RBF), generalized regression neural networks (GRNN), and multi-layer perceptron (MLP) combined with empirical mode decomposition (EMD) are developed for CHF predictive modelling using CHF experimental databases.First, the original experimental inputs data series are decomposed into several intrinsic mode functions (IMFs) and one residual by EMD, whose components are divided into high, medium and low components. The performance parameters of the hybrid models indicates that the root mean square error (RMSE) are 0.8831, 0.6522, and 0.4149; the mean absolute error (MAE) are 0.6697, 0.4636, and 0.1935. The values of the R-square of the developed prediction approach utilizing EMD-RBF, EMD-GRNN, and EMD-MLP models are 0.8553, 0.9302, and 0.9818, and the index of agreement are 0.9464, 0.9700, and 0.9894., The value of the R-square and the index of agreement of the proposed models are much higher than those of the simple models .The Pearson's test results show that the association strength between the measured and the predicted values of the proposed model EMD-MLP is the strongest. These results show the following: (a) compared with other related, recent studies, the prediction accuracy of the hybrid model EMD- MLP proposed in this research is the best hybrid model; (b) the proposed hybrid model (EMD-MLP) attains superior performance compared with simple models.

Djeddou, Messaoud↗
DOE OSTI2021

Reactor scale simulations of ALD and ALE: Ideal and non-ideal self-limited processes in a cylindrical and a 300 mm wafer cross-flow reactor

Here, we have developed a simulation tool to model self-limited processes such as atomic layer deposition (ALD) and atomic layer etching inside reactors of arbitrary geometry as well the output of in situ quartz crystal microbalance and mass spectrometry. We have applied this model to two standard types of cross-flow reactors: a cylindrical tube reactor and a model 300 mm wafer reactor, and explored both ideal and nonideal self-limited kinetics. The model results are in agreement with experimental results and analytic expressions obtained using a simple plug-flow model for the cylindrical tube reactor. We also extended the simulations to consider two nonideal self-limited processes: soft-saturating processes characterized by a slow reaction pathway and processes where surface by-products can compete with the precursor for the same pool of adsorption sites. Our results show that it is possible to have a self-limited process with saturated yet inhomogeneous growth profiles due to the competition of reactor by-products. This is in agreement with experimental observations for titanium dioxide ALD from titanium tetraisopropoxide and titanium tetrachloride precursors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Molecular dynamics study of silicon atomic layer etching by chlorine gas and argon ions

Classical molecular dynamics (MD) is used to simulate atomic layer etching processes of silicon by alternating exposure to chlorine gas and argon ions. In order to validate our model, a rigorous comparison is done with ion beam experiments found in the literature [Park et al., Jpn. J. Appl. Phys. 44, 389 (2005)]. Here it is shown that the etch per cycle (EPC) as a function of argon ion energy from simulations is in quantitative agreement with experimental results if the correct argon ion fluence is used in the simulations. The EPC as a function of ion irradiation time and amount of chlorine exposure also show good agreement with the experiment. The MD simulations also show the formation of an amorphous silicon region with chlorine atoms mixed uniformly throughout following ion bombardment. Finally, the etch products during the ion irradiation step are analyzed and discussed.

74 ATOMIC AND MOLECULAR PHYSICS↗