Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTOR FUELING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 559 records · Page 31
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Fission gas retention of densely packed uranium carbonitride tristructural-isotropic fuel particles in a 3D printed SiC matrix

The Transformational Challenge Reactor (TCR) fuel form was designed to contain large, densely packed uranium carbonitride (UCN) tristructural-isotropic (TRISO) fuel particles within a 3D printed SiC matrix, increasing the uranium density compared to conventional TRISO fuel forms and offering full geometric freedom for core design. Here, this work summarizes initial low-burnup, high-power irradiation testing of TCR fuel materials, including loose UCN TRISO particles and integral fuel compacts with ~55% TRISO particles by volume, to evaluate fission gas retention. Fission gasses were fully retained in all loose particle tests and in integral compacts irradiated at low (<250 °C) surface temperatures. Initial testing at higher (~700–750 °C) fuel surface temperatures showed fission gas release (FGR) and complete fracture of three compacts, but no FGR was observed in later high temperature tests (~300–750 °C) of both fueled compacts and loose TRISO particles. Calculated thermal stresses in the failed compacts were far less than the measured strength of the SiC matrix and the stresses in some failed compacts were less than those in compacts that did not show FGR. Thermal stress-induced matrix cracks also would not cause complete fracture because the tensile stresses transition to compression in the higher temperature regions. Therefore, fuel failure was likely not caused by thermal stresses and may have been related to leakage currents from the electrical heaters and erratic fuel surface temperatures that were only observed in the test for which failure was observed. In any case, the matrix cracks propagated through the coatings of TRISO particles located in the high-density matrix regions on the peripheries of the compacts, resulting in measurable fission gas release. The discussion focuses on the importance of understanding matrix density distributions and the particle-matrix interface properties to prevent matrix cracks from causing TRISO particle failures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Epsilon Metal: A Waste Form for Noble Metals from Used Nuclear Fuel

Epsilon metal (e-metal) is the metallic phase that forms as inclusions at the grain boundaries in the UO2 fuel during reactor operation. This metal is composed of Pd, Mo, Rh, Ru, and Tc. These metallic inclusions are insoluble in strong acid and remnants of these metallic inclusions have been found in the UO2 matrix that remains from the natural reactors in Gabon that were active 1.8 billion years ago, therefore e-metal should be an excellent waste form for the immobilization of the long-lived isotopes 107Pd (6.5 ? 106 a) and 99Tc (2.13 ? 105 a), with 99Tc being the isotope of interest for repository performance. Therefore, the chemical durability of this potential waste form is assessed in this study. Typically, corrosion rates for metallic materials are measured electrochemically because they are quick, inexpensive, and can reveal the mechanism by which a metal corrodes, at least initially. However, in a repository the waste form would be subjected to slowly flowing water without an applied electrical potential over long time periods. Therefore, the corrosion rates of e-metal specimens were measured with both electrochemical tests and the single-pass flow-through test (SPFT). Potentiodynamic and potentiostatic polarization results suggest that a thin passive film exists on the alloy surface, which seems to be responsible for its high corrosion resistance. Additionally, X-Ray photoelectron spectroscopic results suggest that Pd oxides are significantly enriched in the passive film Results from the SPFT show that the dissolution rates were weakly dependent on pH. Only Mo and Re were found in solution and were used for the calculation of the dissolution rates. In general, the electrochemically determined corrosion rates agree reasonably well with the initial dissolution rate measured with the SPFT test, but they are about one or two orders of magnitude higher than the steady state rates. The causes for this discrepancy are discussed.

epsilon-metal, nuclear waste form, corrosion, sing↗
DOE OSTI2022

Initial Observations from AGR 5/6/7 Capsule 1

The fourth and final irradiation experiment in the Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) fuel development and qualification program is designated as AGR-5/6/7. Data collected from the fabrication, irradiation, and post-irradiation examination (PIE) of this tristructural isotropic (TRISO) fuel are intended to serve as the primary data set for the qualification of this fuel for use in high-temperature gas-cooled reactors (INL 2021, Collin 2018b). However, data collected from the three preceding irradiations (i.e., AGR-1, AGR-2, and AGR-3/4) may also be used to supplement data collected from AGR-5/6/7. All components of the AGR-5/6/7 fuel (i.e., UCO kernels, TRISO coatings, and fuel compacts) were produced on an engineering scale at BWXT (Lynchburg, Virginia USA) according to the fuel specification (Marshall 2017). This fuel was irradiated in the northeast flux trap (NEFT) at the Advanced Test Reactor (ATR) at Idaho national Laboratory (INL) from February 16, 2018 to July 22, 2020 (Pham et al. 2021). Measurements in the fission product monitoring system (FPMS) indicated unexpected and significant numbers of failures of TRISO particles in Capsule 1 near the end of the sixth irradiation cycle (ATR Cycle 166A). In the fourth cycle (ATR Cycle 164B) and beyond, the sweep gas flow became very low (presumably from degradation of the capsule gas outlet line via an unidentified mechanism), and the program deliberately isolated Capsule 1 from gas flow periodically. In later cycles, attempts to reestablish any kind of flow in Capsule 1 were unsuccessful. With little or no flow through Capsule 1, FPMS measurements and enumerations of failed particles in Capsule 1 were difficult or impossible as was the ability to control the helium/neon gas mixture used for temperature control. Gas flows and fission gas activity in the effluent gas from the other AGR-5/6/7 capsules were also impacted by the Capsule 1 gas flow issues and the large increase in fission gas released from the Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Safeguarding Reactors and Spent Nuclear Fuel [Slides]

Highly enriched fuel contains large quantities of ²³⁵U; Burned fuel may contain large quantities of ²³⁹Pu; Reprocessing is the major threat (discussed at length later), but we need to ensure the amount of plutonium going to the reprocessing plant is what we believe it to be; All nuclear material needs to be accounted for (material accountancy); There may be a loss of continuity of knowledge in which case fuel needs to be measured to determine how much plutonium and uranium it contains.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Hybrid Zircex Hydrochlorinator

This project was driven by the desire to create easier and faster ways to load Advanced Test Reactor (ATR) Fuel Elements into the Hybrid Zircex hydrochlorinator. The primary requirements for this project were to minimize the potential release of radioactive contamination, minimize maintenance operations to replace or remove the lid seal, and allow for remote usage. Three preliminary designs were made. These designs allow ATR fuel elements to be loaded into the hydrochlorinator more efficiently while fulfilling the requirements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Massively Parallel Bayesian Model Calibration and Uncertainty Quantification with Applications to Nuclear Fuels and Materials

The U.S. Department of Energy (DOE)’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims to develop predictive capabilities by applying computational methods to the analysis and design of advanced reactor and fuel cycle systems. This program has been providing engineering-scale support for the development of BISON, a high-fidelity and high-resolution fuel performance tool. Fuel behavior in a nuclear reactor is governed by a complex network of mechanisms interacting with various other physics aspects in the reactor system. Any model developed to represent the fuel behavior will likely be idealized resulting in uncertainties in their predictions compared to the observed data. As such, this report was motivated by the need to identify the sources of uncertainties and quantify and propagate them through the fuel model outputs. Such quantification of uncertainties will establish a level of model trustworthiness, identify approaches to improve the model trustworthiness, and even guide optimal experiment design for maximal information gain. To accomplish the uncertainty quantification for computational models, this report has relied on the Bayesian framework which provides probabilistic treatment of models their inputs and outputs. The current state-of-the-art on performing Bayesian Uncertainty Quantification (UQ) for nuclear engineering models using High Performance Computing (HPC) resources have been reviewed. Implementation of capabilities for massively parallel Bayesian UQ in Multiphysics Object-Oriented Simulation Environment (MOOSE) is discussed. Several verification cases are discussed to verify the accuracy of the quantified uncertainties using the developed computational capabilities in MOOSE. Then, the problem of quantifying the uncertainties in TRI-Structural isOtropic (TRISO) fuel silver release is addressed. For the first time, the uncertainties arising from the TRISO Fission Gas Release (FGR) model due to model inadequacy and experimental noise are quantified. Also, the Bayesian capabilities are applied to the calibration of the MATPRO creep model, a widely used model in several fuel assessment cases. The impact of the prediction uncertainties in the MATPRO model on the fuel cladding behavior as part of the TRIBULATION assessment case (which is an integral effects case) is investigated. This report concludes with a discussion on the future work for the UQ for computational models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

The Advanced Dimensional Depletion for Engineering of Reactors (ADDER) Software for Depletion and Fuel Management

The Advanced Dimensional Depletion for Engineering of Reactors (ADDER) software is being developed in the Research and Test Reactor (RTR) Program at Argonne National Laboratory to meet the reactor design and analysis needs of the Conversion Program. ADDER is a flexible tool that (1) provides a depletion capability through coupling external neutronics codes with a built-in CRAM solver or external depletion code and (2) provides a user-friendly interface to perform fuel management and criticality search operations. The ADDER software is a Python 3 application written using modern software development practices subject to a compliant implementation of NQA-1 and applicable Department of Energy software quality assurance standards. This report is the user guide for the software release referred to as ADDER v1.1.0. The motivation for a software to have flexible capabilities that ADDER possesses is the need to support a wide variety of geometries that are commonly required in analysis of research and test reactors. These reactors can have complex fuel, experiment, or control material shuffling patterns that persist over several years with many fuel management and partial refueling intervals. The scale of fuel management analysis can require tracking of an inventory that is multiple times the core loading. Many reactors, both power and non-power reactors of various types, will find the features of ADDER useful to facilitate key tasks that a fuel or core design engineer must perform with the convenience of concise input and validated functionality.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

The Advanced Dimensional Depletion for Engineering of Reactors (ADDER) Software for Depletion and Fuel Management

The Advanced Dimensional Depletion for Engineering of Reactors (ADDER) software is being developed in the Research and Test Reactor (RTR) Program at Argonne National Laboratory to meet the reactor design and analysis needs of the Conversion Program. ADDER is a flexible tool that (1) provides a depletion capability through coupling external neutronics codes with a built-in CRAM solver or external depletion code and (2) provides a user-friendly interface to perform fuel management and criticality search operations. The ADDER software is a Python 3 application written using modern software development practices subject to a compliant implementation of NQA-1 and applicable Department of Energy software quality assurance standards. This report is the user guide for the software release referred to as ADDER v1.1.0. The motivation for a software to have flexible capabilities that ADDER possesses is the need to support a wide variety of geometries that are commonly required in analysis of research and test reactors. These reactors can have complex fuel, experiment, or control material shuffling patterns that persist over several years with many fuel management and partial refueling intervals. The scale of fuel management analysis can require tracking of an inventory that is multiple times the core loading. Many reactors, both power and non-power reactors of various types, will find the features of ADDER useful to facilitate key tasks that a fuel or core design engineer must perform with the convenience of concise input and validated functionality.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

USABILITY EXTENSION OF THE ŠKODA VPVR/M CASK FOR TRANSPORTING IRRADIATED FUEL ASSEMBLIES

New abstract from the final version being submitted now: This paper discusses the evolution and enhanced usability of the ŠKODA VPVR/M cask for the transport of irradiated fuel assemblies, particularly within the context of the demand for the delivery of newly appearing irradiated HEU fuel types for which the cask did not yet have a license to transport. Over time, the cask’s internal basket construction has demonstrated notable adaptability to accommodate various exotic HEU fuel types from research reactors of differing origins. The paper outlines sever-al custom internal baskets developed for specific fuel types, including those from Belarus and Serbia, as well as from Georgia, Uzbekistan, and MNSR cores, as well as a recently designed basket for MTR and TRIGA assemblies. The findings high-light the high flexibility and adaptability of the cask, supported by successful rede-signs and licensing efforts, underscoring its value for the safe and secure transport of nuclear material. Old abstract from the draft version that was already approved: The Russian Research Reactor Fuel Return (RRRFR) program, since its inception, has continuously used the ŠKODA VPVR/M Cask fleet designed for the repatriation of irradiated highly enriched uranium (HEU) fuel. As the program progressed (from shut-down and a quasi-abandoned reactor, and/or as it began to include fuels of Chinese and US origin), new challenges emerged for the transport Cask. These were fuel types that had not yet been licensed for the Cask. Although these requirements did not arise during the design of the basic ŠKODA VPVR/M Cask, as revealed by the retrospective analyses, the Internal Basket of the ŠKODA VPVR/M Cask gives a high degree of flexibility to accommodate additional fuel types. This paper provides a brief overview of the ŠKODA VPVR/M Cask, which holds a B(U) type license, and introduces the different types of Internal Baskets that have already been licensed to transport so-called exotic irradiated HEU fuel types, in addition to the original license. The paper presents a new Internal Basket design for accommodating MTR-type and TRIGA-type irradiated HEU fuel assemblies. This includes a detailed presentation of the design basis and the new MTR-TRIGA Internal Basket, as well as the licensing matters of the package under the name ŠKODA MTR-TRIGA Cask, and the conformity test (dry- and wet-run) operations made to verify compliance with the new Internal Basket. Then, as a summary, the usage record for the Cask fleet is presented, and finally, the paper concludes with the consolidated experiences gained during the utilization of the ŠKODA VPVR/M Cask fleet, emphasizing the high degree of Cask flexibility ensured by the Internal Basket’s construction.

42 - ENGINEERING↗
DOE OSTI2023

A Review of Candidates for a Validation Data Set for High-Assay Low-Enrichment Uranium Fuels

Many advanced reactor concept designs rely on high-assay low-enriched uranium (HALEU) fuel, enriched up to approximately 19.75% 235 U by weight. Efforts are underway by the US government to increase HALEU production in the United States to meet anticipated needs. However, very few data exist for validation of computational models that include HALEU, beyond a few fresh fuel benchmark specifications in the International Reactor Physics Experiment Evaluation Project. Nevertheless, there are other data with potential value available for developing into quality benchmarks for use in data- and software-validation efforts. This paper reviews the available evaluated HALEU fuel benchmarks and some of the potentially relevant benchmarks for fresh highly enriched uranium. It then introduces experimental data for HALEU fuel irradiated at Idaho National Laboratory, from relatively recent irradiation programs at the Advanced Test Reactor. Such data should be evaluated and, if valuable, collected into detailed benchmark specifications to meet the needs of HALEU-based reactor designers.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Neutronic Performance of a Compact 10 MWe Nuclear Reactor with Low Enrichment (ThxU1−x)N Fuel

Abstract Recent interest in compact nuclear reactors for applications in space or in remote locations drives innovation in nuclear fuel design, especially non-oxide ceramic nuclear fuels. This work details neutronic modeling designed to support the development of a new nuclear fuel concept based on a mixture of thorium and uranium nitride. A Monte Carlo N-Particle Version 6.2 (MCNP-6) model of a compact 10 MWe reactor design which incorporates (Th x U 1− x )N fuel is presented. In this context, a “compact” reactor is a completely assembled reactor which may be emptied of coolant and transported by specialized commercial vehicle, deployed by a C130J aircraft, or launched into space. Core geometry, reflector barrels, and the heat exchange zones are designed to support reduction of overall reactor volume of core components while maintaining criticality with a fixed total fuel mass of 4500 kg. Dense mixed nitrides of thorium nitride (ThN) additions in uranium nitride (UN) in 5 wt.% increments between $$0.05 \le x \le 0.5$$ 0.05 ≤ x ≤ 0.5 have been considered for calculation of $$k_{\infty }$$ k ∞ and $$k_{{{\text{effective}}}}$$ k effective . ThN additions in UN results in a slight increase in the magnitude of the temperature coefficient of reactivity, which is negative by design. The isotopic distribution of the principal actinide inventory as a function of burnup, time, and initial fuel composition is presented and discussed within the context of the proliferation risk of this core design.

Parker, S. S. (ORCID:000000018597440X)↗
DOE OSTI2023

Automated reactor physics analysis framework of High Flux Isotope Reactor low-enriched uranium silicide dispersion fuel designs

The High Flux Isotope Reactor (HFIR) is a versatile research reactor that provides one of the highest steady-state neutron fluxes of any reactor in the world. The HFIR reactor physics team investigated the conversion of the current 93 wt% highly enriched uranium U 3 O 8 -Al dispersion fuel to a 19.75% low-enriched uranium (LEU) U 3 Si 2 -Al dispersion fuel. The team continuously develops a Python module to streamline the analysis steps required for an LEU core design to ensure reproducible and agile design iteration. The Python module automates the data processing between analysis steps and automates the input perturbation for branch calculations and design changes. The automated framework has proven to significantly increase the efficiency and reproducibility of the reactor physics team to design High Flux Isotope Reactor (HFIR) LEU cores and thoroughly analyze performance metrics, safety metrics, and thermal safety margins. Consequently, the team can now respond rapidly to fuel fabrication engineer and thermal-hydraulic-structural analyst requests. Numerous combinations of LEU fuel designs are explored, of which two LEU fuel designs are presented here in this paper: a low density silicide design, and a high-density silicide design. Results show that both designs meet or exceed safety and performance metrics with exception for minor differences caused by the hardened spectrum from LEU.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Application of Dynamical System Scaling for Accelerated Fuel Qualification Efforts

There are considerable ongoing research and testing campaigns to qualify new fuel designs such as metallic fuels for advanced reactor designs and the Accident Tolerant Fuel (ATF) campaign for light water reactors (LWR). The typical research and development lifecycle needed to qualify a nuclear fuel design, under ideal conditions, can take up to 20-25 years which limits the ability for new fuels to make fast deployments into commercial, test, and research reactors. While there are several efforts to accelerate nuclear fuel qualification through advanced modeling coupled with state-of-the-art experiments, there is not yet a framework to methodically quantify and rank distortions occurring in experimental test specimens needed to validate nuclear fuel performance codes. This study uses the Dynamical System Scaling (DSS) methodology to quantify transient scaling distortions that occur over experiment and simulated transients. DSS analysis metrics provide a researcher with several tools and information embedded within test data to identify dominant phenomena, associated timescales, and quantify a transient?s overall dynamic distortion. This is demonstrated with separate analyses of the SETH-C and CHF-SERTTA thermal-hydraulic experiments in the TREAT facility at Idaho National Laboratory. The outcome of this work is a scaling and data analysis approach to account for the influence a scaled fuel test specimen?s geometric and temporal distortions have on its ability to be representative of the full-scale design.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Conceptual Fuel Element Design Candidates for Conversion of High Flux Isotope Reactor with Low-Enriched Uranium Silicide Dispersion Fuel

Engineering design studies are underway to assess the feasibility of converting the High Flux Isotope Reactor (HFIR) to operate with low-enriched uranium (LEU) silicide dispersion (U3Si2-Al) fuel. These studies are supported by the U.S. Department of Energy National Nuclear Security Administration’s Office of Material Management and Minimization. A systematic approach employing neutronic and thermal-hydraulic analyses have been performed with the ORNL Shift and HFIR Steady State Heat Transfer Code tools, respectively, to predict reactor performance and thermal safety margins for proposed LEU3Si2-Al fuel designs. The design process was initiated by generating an optimized design with fabrication features identified from previous studies that result in excellent performance and safety metrics. The approach continued by substituting a single fabrication feature anticipated to be difficult to manufacture with another feature expected to perform an analogous function to that of the removed feature. Four conceptual fuel element design candidates, with various fabrication features, for conversion of HFIR with 4.8 gU/cm3 LEU3Si2-Al fuel have been generated and shown to meet pre-defined performance and safety metrics. Results to date indicate that HFIR could convert with the subject fuel system and meet performance and safety requirements if, among other considerations, fabrication of the specific design features are demonstrated and qualification of the fuel is complete under HFIR-specific conditions.

Chandler, David↗
DOE OSTI2022

November 2022 NS&T Highlights

These are the highlights for the Nuclear Science and Technology organization for the month of November.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

CFD-Chemical Model of One-Third Scale Demonstration of DOE Sealed Canister with ATR Fuel

Road-ready and final disposition packaging configurations for the advanced test reactor (ATR) fuel currently specifies storage within helium backfilled DOE sealed standard canisters. The aluminum cladding of the ATR fuel contains an oxyhydroxide layer of boehmite/bayerite that generates hydrogen when subjected to irradiation. Understanding the effect of this hydrogen buildup over time to important for long term storage considerations. Previous modeling efforts have built a coupled CFD-chemical model to simulate the temperature gas phase concentrations within the DOE sealed standard canisters. A demonstration case for these DOE sealed canisters will be eventually performed with a one-third scale mockup that has been instrumented with thermocouples and gas concentration probes. This study seeks to model the planned canister for validation of the previously developed model, such that confidence in its long-term prediction can be increased. The deployment of the instrumented lid for online monitoring in intended for a period of 10+ years based on previous monitoring of commercial fuel storage; however, the model is still run for the previously used 50-year storage periods. This case is modeled with a G-value using a bi-linear function such that it decreases at higher dose rates to be consistent with experiments. Validation efforts of the model would likely revolve around the results for the 1st year, so the results of this timeframe are also highlighted. For dried fuel of the nominal decay heat (18W), the predicted hydrogen concentration is 0.19% after 1 year, 0.91% after 10 years, and 2.8% after 50 years, with a maximum pressure of 1.26 atm. Consistent with previous modeling, the decay heat of the fuel is the main factor that influences the results. For undried fuel in pure helium, the hydrogen concentration ranges from 0.23 to 1.2% after 1 year, 1.25-6.2% after 10 years and 8.8 to 18.84% after 50 years. For dried fuel in pure helium the hydrogen concentration ranges from 0.06% to 0.34% after 1 year, 0.35-2.11% after 10 years and 0.95 to 6.6% after 50 years. While long-term results in the presence of residual air are mostly the same, early reactions with O 2 can delay significant production of H 2 until it is consumed to form more water vapor, lowering the range to 0.14 to 1.0% after 1 year. The maximum absolute pressure that is reached across any scenario is 2.06 atm. In the event of residual air, the presence of nitric acid is possible in the range of 18-131 ppm after 1 year, 174-1180 ppm after 10 years, and 586-3500 ppm after 50 years. As long as the fuel is sufficiently dried, or of nominal decay heat, a 4% lower flammability limit of hydrogen will not be reached within a 10-year monitoring period.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗