Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface exchange”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 541 records · Page 30
All sourcesNASA NTRSDOE OSTI
NASA NTRS1948

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 2: 50% Impartitioned Blades

The icing protection afforded an internal air-heated propeller blade by radial partitioning at 50-percent chord to confine the heated air to the forward half of the blade was determined in the NACA Cleveland icing research tunnel. A modified production-model hollow steel propeller, was used for the investigation. Temperatures of the blade surfaces for several heating rates were measured under various tunnel Icing' conditions. Photographic observations of ice formations on blade surfaces and blade heat-exchanger effectiveness were obtained. With 50-percent partitioning of the blades, adequate icing protection at 1050 rpm was obtained with a heating rate of 26,000 Btu per hour per blade at the blade shank using an air temperature of 400 F with a flow rate of 280 pounds per hour per blade, which is one-third less heat than was found necessary for similar Ice protection with unpartitioned blades. The chordwise distribution of the applied heat, as determined by surface temperature measurements, was considered unsatisfactory with much of the heat dissipated well back of the leading edge. Heat-exchanger effectiveness of approximately 56 percent also Indicated poor utilization of available heat. This effectiveness was, however, 9 percent greater than that obtained from unpartitioned blades.

Perkins, Porter J.↗
DOE OSTI2023

The importance of explicitly representing the streambed in watershed models

Abstract The streambed is the critical interface between the aquatic and terrestrial systems and hosts important biogeochemical hot spots within river corridors. Although the streambed characteristics are significantly different from those of its surrounding soil, the streambed itself has not been explicitly represented in watershed models. Here, we explicitly incorporated a streambed layer into an integrated hydrologic model through model parameterization and discretization. We examined the hydrological effects of streambed characteristics, including hydraulic conductivity ( K ), layer thickness, and resolution, on the exchange fluxes across the streambed as well as the streamflow at the watershed outlet. The numerical experiments were performed in the American River Watershed, a headwater, mountainous watershed within the Yakima River Basin in central Washington. Despite having a negligible effect on the watershed streamflow, an explicit representation of the streambed with distinctive properties dramatically changed the magnitude and variability of the exchange flux. In general, a larger streambed K along with a thicker streambed layer induced larger exchange fluxes. The exchange flux was most sensitive to the streambed resolution. A finer streambed resolution increased exchange fluxes per unit area while reducing the overall exchange volumes across the entire streambed. The amount of baseflow decreased by 6% as the streambed resolution increased from 250 to 50 m. This finding is important because these hydrological changes may, in turn, affect the exchange of nutrients and contaminants between surface water and groundwater and the associated biogeochemical processes. Our work demonstrated the importance of representing streambeds in fully distributed, process‐based watershed models to better capture the exchange flow dynamics in river corridors.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Kilometer-Scale Hydrologic Exchange Flows in a Gravel Bed River Corridor and Their Implications to Solute Migration

In this work, a well-characterized field site along a major river corridor was used to investigate the dynamic pathways and impacts of subsurface hydrogeologic structures on kilometer-scale hydrologic exchange flows between river water and groundwater. A aqueous uranium (U aq ) plume exists at the site that discharges to the Columbia River. We performed temporally intensive monitoring of specific conductance (SpC) and U aq concentrations within the plume at increasing distances from the river shoreline and at locations both within and outside a presumed subsurface pathway of lateral hydrologic exchange. Specific conductance and U aq were utilized as in-situ tracers of hydrologic exchange and associated groundwater-surface water mixing. Monitoring data was collected for an approximate two year period during which seasonal river elevations varied by more than 2 m causing distinct events of river water intrusion and retreat from the near-shore aquifer, and large temporal variations in well-water analyte concentrations. Statistical clustering analysis was applied to identify well groupings exhibiting common time series behaviors. PFLOTRAN was implemented within a modeling domain of 3.3 x 1.9 km with dynamic flow boundary conditions and accurate subsurface topography for the basal aquitard underlying the aquifer. In-silico calculations of river water tracer behavior were performed to assess predominant flow directions and velocities influenced by river stage variations and variable aquitard topography, and their collective influences on SpC and U aq concentrations. We demonstrate complicated multidirectional flow behaviors at the kilometer scale resulting from hydrologic exchange and subsurface structure that influence plume dynamics and determine the overall system behavior.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Printed circuit primary heat exchanger for power conversion in heat pipe microreactor applications

Here, in the present study, a model was developed for a recuperated air Brayton cycle for heat pipe microreactors, and the effect of the primary heat exchanger type assessed. An annular flow heat exchanger and a printed circuit heat exchanger (PCHE) were evaluated. A sub-sized diffusion bonded, PCHE test specimen was manufactured and tested with nitrogen as the working fluid to validate and improve the PCHE model. A comparison of the thermal cycle efficiency for the Brayton cycle coupled to a heat pipe microreactor using each of the two primary heat exchangers showed competitive performance for both options, with achievable cycle efficiencies of 34 % and 35 % for the annular and printed circuit heat exchangers, respectively. The impact of heat pipe length and additional reheating stages on cycle efficiency was studied. Increasing the heat pipe condenser length from 0.8 to 2.0 m resulted in an increase in cycle efficiency of 3.5 % and 3.2 % for the annular and printed circuit heat exchangers, respectively. The use of additional reheating stages showed a reduction in cycle efficiency since the heat pipe surface area limits the primary heat exchanger size and effectiveness. These results highlight the importance of the primary heat exchanger on the performance of a heat pipe microreactor. Overall, the cycle model, testing, and heat exchanger model showed the potential for the PCHE to improve the economics of a heat pipe microreactor relative to the annular flow heat exchanger, which also opens the possibility to use different heat transfer fluids such as supercritical CO 2 .

PCHE↗
NASA NTRS2017

Laser Processed Heat Exchangers

The Laser Processed Heat Exchanger project will investigate the use of laser processed surfaces to reduce mass and volume in liquid/liquid heat exchangers as well as the replacement of the harmful and problematic coatings of the Condensing Heat Exchangers (CHX). For this project, two scale unit test articles will be designed, manufactured, and tested. These two units are a high efficiency liquid/liquid HX and a high reliability CHX.

Hansen, Scott↗
NASA NTRS1982

Measurement and evaluation of swirl-type flow in labyrinth seals of conventional turbine stages

The effects of load factor and rotor eccentricity were determined on flow conditions in test series for two stages. The results indicate that swirl-type entry flow follows the rules of potential swirl. Within the labyrinth cavities two spatial separated flow areas are considered. A dominating flow in periphera direction nearly fills the space between the sealing strips and the ceiling of the cavity. Below this flow, an area of axial mass transport is situated, with a slight peripheral component, limited on the nearest surroundings of the seals gap and the rotor surface. Between both flows, an exchange of energy takes place. Within the gaps, flow direction depends on axial velocity and therefore on variable flow contraction. A balance of energy within the seal and the cavities interprets the results of lateral force measurements as an influence of friction at the sealing strips surface and the rotating shaft surface. Stages with their blades put together in buckets by means of shrouding segments are particularly influenced by the rotating speed of the shrouding.

Hauck, L.↗
DOE OSTI2021

Transparent silica aerogel slabs synthesized from nanoparticle colloidal suspensions at near ambient conditions on omniphobic liquid substrates

This paper presents a novel sol-gel method to synthesize large and thick silica aerogel monoliths at near ambient conditions using a commercial aqueous solution of colloidal silica nanoparticles as building blocks. To achieve slabs with high visible transmittance and low thermal conductivity, the method combines the strategies of (i) synthesizing gels on an omniphobic perfluorocarbon liquid substrate, (ii) aging at temperatures above room temperature, and (iii) performing solvent exchange with a low-surface-tension organic solvent prior to ambient drying. The omniphobic liquid substrates were used to prevent cracking and ensure an optically-smooth surface, while nanoparticle building blocks were small (<10 nm) to limit volumetric light scattering. Gels were aged at temperatures between 25 and 80 °C for up to 21 days to make them stronger and stiffer and to reduce shrinkage and cracking during ambient drying. Ambient drying was achieved by first exchanging water in the gel pores for octane, followed by drying in an octane-rich atmosphere to decrease capillary forces. The synthesized nanoparticle-based silica aerogel monoliths had thicknesses up to 5 mm, diameters up to 10 cm, porosities exceeding 80%, and thermal conductivities as low as 0.08 W m –1 K –1 . Notably, the slabs featured visible transmittance exceeding 75% even for slabs as thick as 5 mm. The as-synthesized aerogel monoliths were exposed to TMCS vapor to induce hydrophobic properties resulting in a water contact angle of 140° that prevented water infiltration into the pores and protected the aerogels from water damage. This simple synthesis route conducted at near ambient conditions produces hydrophobic aerogel monoliths with promising optically transparent and thermally insulating properties that can be adhered to glass panes for window insulation and solar-thermal energy conversion applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Convective heat transfer enhancement through additively built multiscale micro-tetrahedron features

Use of Additive Manufacturing (AM) to improve the heat transfer characteristics of tip shrouds in high-pressure turbines is being considered by industries. Existing designs of these components integrate micro-cooling channels to reduce the bulk temperature for improved life. In this research, closely packed micro tetrahedron features in addition to AM roughness has been considered. Further, this multiscale surface characteristics increased surface area per unit volume available for heat exchange. Micro-tet features were designed, manufactured, characterized, and evaluated systematically while increasing their height. An enormous increase in the overall wetted surface area by 200 % was measured. The convective heat transfer enhancement was ~3.72 times EDM rough coupon, and friction factor enhancement was ~5.5 times EDM rough coupon. Furthermore, the proposed design offers 2.5 times enhanced heat transfer for a given 2 W pumping power compared to our EDM rough coupon. Heat transfer enhancement was observed to not vary strongly with increased Reynolds number. Such complex designs are only possible through additive manufacturing for increased heat transfer with little pressure penalty. Finally, increasing the micro-tet height for increased surface area and improved heat exchange beyond an upper limit might not be a significant benefit as it gets compensated by increasing skin friction.

42 ENGINEERING↗
DOE OSTI2024

A Three–Dimensional Nanoscale View of Electrocatalyst Degradation in Hydrogen Fuel Cells

The loss of platinum (Pt) electrochemically active surface area (ECSA) is a critical degradation mode that often becomes a limiting factor for heavy-duty proton exchange membrane fuel cell vehicles. High surface area carbon supports have been shown to improve Pt dispersion and limit detrimental ionomer-electrocatalyst interactions due to their large interior pore volume. Here, in this work, using automated scanning transmission electron tomography, the degradation of nanoparticles located on the interior versus exterior surfaces of the carbon support is compared following a catalyst-specific accelerated stress test (AST) of 90,000 voltage cycles between 0.6 V to 0.95 V. The results reveal a notable increase in median particle size for both interior and exterior Pt catalyst particles, with a slightly higher increase in particle size distribution and loss of specific surface area for the particles located on the exterior carbon surface. The fraction of Pt nanoparticles that reside within the interior of the carbon support also increased following the AST test, accompanied by evidence of an increase in average carbon mesopore size. Here, the results shed light on the degradation mechanisms affecting electrochemical properties and the enhanced particle accessibility at lower relative humidity.

08 HYDROGEN↗
DOE OSTI2022

Rapid vertical exchange at fronts in the Northern Gulf of Mexico

Over the Texas-Louisiana Shelf in the Northern Gulf of Mexico, the eutrophic, fresh Mississippi/Atchafalaya river plume isolates saltier waters below, supporting the formation of bottom hypoxia in summer. The plume also generates strong density fronts, features of the circulation that are known pathways for the exchange of water between the ocean surface and the deep. Using high-resolution ocean observations and numerical simulations, we demonstrate how the summer land-sea breeze generates rapid vertical exchange at the plume fronts. We show that the interaction between the land-sea breeze and the fronts leads to convergence/divergence in the surface mixed layer, which further facilitates a slantwise circulation that subducts surface water along isopycnals into the interior and upwells bottom waters to the surface. This process causes significant vertical displacements of water parcels and creates a ventilation pathway for the bottom water in the northern Gulf. The ventilation of bottom water can bypass the stratification barrier associated with the Mississippi/Atchafalaya river plume and might impact the dynamics of the region’s dead zone.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Heat dissipation systems with hygroscopic working fluid

In various embodiments, the present invention relates to heat dissipation systems including a hygroscopic working fluid and methods of using the same. In various embodiments, the present invention provides a method for heat dissipation using a hygroscopic working fluid. The method can include transferring thermal energy from a heated process fluid to the hygroscopic working fluid in a process heat exchanger, to form a cooled process fluid. The method can include condensing liquid from a feed gas on a heat transfer surface of a feed gas heat exchanger in contact with the cooled process fluid, to form a cooled feed gas, the heated process fluid, and a condensate. The method can include dissipating thermal energy from the hygroscopic working fluid to a cooling gas composition with a fluid-air contactor. The method can include transferring moisture between the hygroscopic working fluid and the cooling gas composition with the fluid-air contactor. The method can include adding at least part of the condensate to the hygroscopic working fluid.

Martin, Christopher Lee↗
NASA NTRS2001

Icehouse Effect: A Selective Arctic Cooling Trend Current Models are Missing

The icehouse effect is a hypothesized climate feedback mechanism which could result in human-caused surface cooling trends in polar regions. Once understood in detail, it becomes apparent that these trends, which are discernable in the literature, but have been largely dismissed, do not conflict with the consensus assessment of the evidence, which infers century-scale Arctic warming. In fact, confirmation of the hypothesis would substantially strengthen the argument that there is a detectable human influence on today's climate. This apparent enigma is resolved only through careful attention to the detail of the hypothesis and the data supporting it. The posited surface cooling is entirely dependent on the existence of climate warming in layers capping the stable boundary layer. Also, the cooling is not pandemic, but is selective. It is readily revealed in properly sorted data by making use of the principles of micrometeorological similarity. Specifically, the cooling is manifest under a range of favorable turbulence conditions which can develop and disappear locally on time scales of minutes to hours because of the intrinsically intermittent nature of stable boundary layer turbulence. Because of the fine-scale nature of the processes which produce the cooling, modeling it is a difficult proposition. Vertical resolution on the order of 1 meter is required. Adequate models of intermittent surface fluxes coupled with radiation exchange do not currently exist, not as parameterizations for aggregated systems, nor in large eddy simulation (LES) models. This presentation will introduce the theory. An important testable null hypothesis emerges: the icehouse effect produces a unique signature or "fingerprint" which could not be produced by any other known process. The presence of this signature will be demonstrated using nearly all available Arctic temperature observations. Its aggregate effect is clearly found in Arctic monthly surface temperature trends when sorted by climatological stability. Using all available Arctic rawinsonde ascents - about 1.1 million profiles, "frozen moments" of the icehouse processes are captured in various states. Because turbulent time scales are so short in the stable boundary layer. each of these snapshots can be treated as independent -- their chronology is irrelevant. Micrometeorological similarity is invoked to reassemble the soundings into bins of similar stability and it is in a wide, coherent range of these stability bins where the cooling effect is revealed.

Wetzel, Peter J.↗
DOE OSTI2023

Estimating source-sink distributions and fluxes of reactive nitrogen and sulfur within a mixed forest canopy

The vertical source-sink distribution of air pollutants within and above forested canopies is necessary for describing the biological, physical, and chemical processes influencing the soil-vegetation-atmosphere exchange. Here, this study implemented inverse modeling methods to estimate the source-sink and flux profiles of reactive nitrogen (N) and sulfur (S) compounds from measurements of the mean concentration profiles of ammonia (NH 3 ), nitric acid (HNO 3 ), sulfur dioxide (SO 2 ), and particulate ammonium (NH 4 + ), nitrate (NO 3 − ), and sulfate (SO 4 2− ) at a forest site in the southern Appalachian Mountains. Three inverse approaches utilizing different approximations to scalar transport within the canopy were developed and evaluated against sensible heat flux measurements. The Eulerian model (EUL), which incorporates vertical velocity skewness, performed well in reproducing the turbulent heat fluxes and was subsequently used to calculate the chemical source-sink and flux profiles. Above-canopy fluxes of NH 3 were downward, indicating that the forest was a net sink of NH 3 . The soil/litter layer was both a source and a sink for NH 3 but the exchange rate at the forest floor was small. Fluxes of HNO 3 , SO 2 , NO 3 − , NH 4 + , and SO 4 2- were uni-directional (deposition only) between the air and the canopy/ground and increased monotonically from the forest floor to the canopy top. Crown foliage dominated the uptake of reactive N and S during the growing season, accounting for 80–90% of the total canopy-scale flux. Fluxes and canopy-ground partitioning estimated using the resistance-based Surface Tiled Aerosol and Gas Exchange (STAGE) model were generally comparable to EUL. The comparison highlights the need for improved parameterizations of litter exchange and NH 3 compensation points in resistance models for forest ecosystems. The findings here benefit the application of critical loads in forest ecosystems and guide further development of resistance-based exchange models.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Soil pH Buffering Capacity, Geochemical Characterization, and Soil Water Retention for Arctic Soils of Seward Peninsula and Utqiagvik, Alaska, 2013-2019

This dataset provides pH titration data and soil pH buffering capacities of 21 Arctic soils that were collected between 2013-2019. Geochemical data including soil organic carbon, carbon:nitrogen ratio, initial pH, and gravimetric water content are also reported. Additional measurements of cation exchange capacity and soil water retention (dry range) are presented for selected soils. A script, developed in R, is also included for a simple biogeochemical simulation that incorporates soil pH buffering capacity. This dataset contains 7 csv files and one R script.The Next-Generation Ecosystem Experiments: Arctic (NGEE Arctic), was a research effort to reduce uncertainty in Earth System Models by developing a predictive understanding of carbon-rich Arctic ecosystems and feedbacks to climate. NGEE Arctic was supported by the Department of Energy's Office of Biological and Environmental Research.The NGEE Arctic project had two field research sites: 1) located within the Arctic polygonal tundra coastal region on the Barrow Environmental Observatory (BEO) and the North Slope near Utqiagvik (Barrow), Alaska and 2) multiple areas on the discontinuous permafrost region of the Seward Peninsula north of Nome, Alaska.Through observations, experiments, and synthesis with existing datasets, NGEE Arctic provided an enhanced knowledge base for multi-scale modeling and contributed to improved process representation at global pan-Arctic scales within the Department of Energy's Earth system Model (the Energy Exascale Earth System Model, or E3SM), and specifically within the E3SM Land Model component (ELM).

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1994

Self-lubricated mantle convection: Two-dimensional models

We present results from convection models allowing for self-lubrication of downflows. Models impose a line source of chemically light, low viscosity material at the top of a convecting layer of temperature-dependent viscosity material. Low viscosity surface material serves as an analog to hydrated sediment/crust and the high viscosity upper portion of the convecting layer as an analog to mantle lithosphere. Slow near surface motion in the convecting layer entrains low viscosity material into zones of downflow, which has a lubricating effect. Once entrained lubricant is deeper than the cold high viscosity portion of the convecting layer, rapid upper boundary layer overturn occurs and system properties change (e.g., heat flux doubles). This marks transition to a lubricated state. Before and after transition, transport properties are dominantly determined by, respectively, the viscosity of mantle lithosphere and that of interior mantle. Lubricated and nonlubricated states appear as distinct regions in system output space suggesting that exchange between them is akin to a phase transition. That such exchange depends on a near surface lubricant implies that the geodynamics of planets lacking such lubricants may fundamentally differ from that of planets possessing them.

Lenardic, A.↗
NASA NTRS1996

Advanced Techniques for Improving Wind Direction Ambiguity Removal in Scatterometry

Ocean surface winds, which drive the ocean currents and momentum flux exchanges, are critical for atmospheric and oceanographic studies. Ocean surface winds also generate small capillary waves which affect the normalized radar cross section of the ocean surface. A scatterometer is a microwave radar which measures these cross section values. This talk describes related new techniques.

Scatterometry↗
NASA NTRS1977

Determination of three-dimensional radiative exchange factors for the Space Shuttle by Monte Carlo

A program was developed to predict radiative exchange factors in three-dimensional configurations with curved, specularly-reflecting surfaces using the Monte Carlo method. It was shown that this can be done efficiently by using the normal Monte Carlo method for closed configurations and/or high surface emissivities, while Energy Partitioning should be used for open configurations and/or low surface emissivities. Comparison with experiments on the Space Shuttle radiator panels showed that the simple model of gray, diffuse emission is sufficient for the prediction of exchange factors between actual (silver-coated teflon) surfaces. For solar-irradiation exchange factors on the Space Shuttle, on the other hand, spectral and directional variations of surface properties must be taken into account.

Modest, M. F.↗
NASA NTRS2003

A GCM Recent History of the Northern Martian Polar Layered Deposits

The polar layered deposits are thought to contain alternate layers of water and dust in different proportions resulting from the astronomical forcing of the martian climate. In particular, longterm variations in the orbital and axial elements of Mars are presumed to generate variations of the latitudes of surface water ice stability and of the amount of water exchanged in the polar areas. At high obliquity, simplified climate models and independent general circulation simulations suggest a transfer of water ice from the north polar region to tropical areas, whereas at lower and present obliquities, water ice is expected to be stable only at the poles. If so, over obliquity cycles, water ice may be redistributed between the surface water reservoirs leading to their incremental building or disintegration depending on the rates of water transfer. If only a relative limited amount of the available water is exchanged on orbital timescales, this may provide an efficient mechanism for the formation of the observed polar deposits. Within this context, GCM simulations of the martian water cycle have been performed for various obliquities ranging from 15 degrees to 45 degrees and for a large set of initial water ice locations to determine the rate of water exchange between the surface water reservoirs as a function of the obliquity. Propagating these rates over the last 10 Ma orbital history gives a possible recent evolution of these reservoirs.

Levrard, B.↗