Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “smart materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Active Blade Vibration Control Being Developed and Tested

Gas turbine engines are currently being designed to have increased performance, lower weight and manufacturing costs, and higher reliability. Consequently, turbomachinery components, such as turbine and compressor blades, have designs that are susceptible to new vibration problems and eventual in-service failure due to high-cycle fatigue. To address this problem, researchers at the NASA Glenn Research Center are developing and testing innovative active blade vibration control concepts. Preliminary results of using an active blade vibration control system, involving a rotor supported by an active magnetic bearing in Glenn's Dynamic Spin Rig, indicate promising results (see the photograph). Active blade vibration control was achieved using feedback of blade strain gauge signals within the magnetic bearing control loop. The vibration amplitude was reduced substantially (see the graphs). Also, vibration amplitude amplification was demonstrated; this could be used to enhance structural mode identification, if desired. These results were for a nonrotating two-bladed disk. Tests for rotating blades are planned. Current and future active blade vibration control research is planned to use a fully magnetically suspended rotor and smart materials. For the fully magnetically suspended rotor work, three magnetic bearings (two radial and one axial) will be used as actuators instead of one magnetic bearing. This will allow additional degrees of freedom to be used for control. For the smart materials work, control effectors located on and off the blade will be considered. Piezoelectric materials will be considered for on-the-blade actuation, and actuator placement on a stator vane, or other nearby structure, will be investigated for off-the-blade actuation. Initial work will focus on determining the feasibility of these methods by performing basic analysis and simple experiments involving feedback control.

Johnson, Dexter↗
NASA NTRS2005

Multi-Scale Sizing of Lightweight Multifunctional Spacecraft Structural Components

This document is the final report for the project entitled, "Multi-Scale Sizing of Lightweight Multifunctional Spacecraft Structural Components," funded under the NRA entitled "Cross-Enterprise Technology Development Program" issued by the NASA Office of Space Science in 2000. The project was funded in 2001, and spanned a four year period from March, 2001 to February, 2005. Through enhancements to and synthesis of unique, state of the art structural mechanics and micromechanics analysis software, a new multi-scale tool has been developed that enables design, analysis, and sizing of advance lightweight composite and smart materials and structures from the full vehicle, to the stiffened structure, to the micro (fiber and matrix) scales. The new software tool has broad, cross-cutting value to current and future NASA missions that will rely on advanced composite and smart materials and structures.

Bednarcyk, Brett A.↗
NASA NTRS2000

Design of the Active Elevon Rotor for Low Vibration

Helicopter fuselages vibrate more than desired, and traditional solutions have limited effectiveness and can impose an appreciable weight penalty. Alternative methods of combating high vibration, including Higher Harmonic Control (HHC) via harmonic swashplate motion and Individual Blade Control (IBC) via active pitch links, have been studied for several decades. HHC via an on-blade control surface was tested in 1977 on a full scale rotor using a secondary active swashplate and a mechanical control system. Recent smart material advances have prompted new research into the use of on-blade control concepts. Recent analytical studies have indicated that the use of on-blade control surfaces produces vibration reduction comparable to swashplate-based HHC but for less power. Furthermore, smart materials (such as piezoceramics) have been shown to provide sufficient control authority for preliminary rotor experiments. These experiments were initially performed at small scale for reduced tip speeds. More recent experiments have been conducted at or near full tip speeds, and a full-scale active rotor is under development by Boeing with Eurocopter et al. pursuing a similarly advanced full-scale implementation. The US Army Aeroflightdynamics Directorate has undertaken a new research program called the Active Elevon Rotor (AER) Focus Demo. This program includes the design, fabrication, and wind. tunnel testing of a four-bladed, 12.96 ft diameter rotor with one or two on-blade elevons per blade. The rotor, which will be Mach scaled, will use 2-5/rev elevon motion for closed-loop control and :will be tested in late 2001. The primary goal of the AER Focus Demo is the reduction of vibratory hub loads by 80% and the reduction of vibratory blade structural loads. A secondary goal is the reduction of rotor power. The third priority is the measurement and possible reduction of Blade Vortex Interaction (BVI) noise. The present study is focused on elevon effectiveness, that is, the elevon's ability to reduce all six components of the nonrotating 4/rev hub loads. Some design parameters have been kept fixed in this study, while others have been varied to determine their influence - on elevon effectiveness. The fixed parameters include all blade structural properties except for torsion stiffness; the varied parameters include torsion stiffness, elevon aerodynamic location, and the number and individual authority of elevon aerodynamic surfaces. This paper describes the preliminary design process being used for the AER, and describes and quantifies the emerging active rotor characteristics.

Fulton, Mark V.↗
NASA NTRS2005

Development, Implementation and Application of Micromechanical Analysis Tools for Advanced High Temperature Composites

This document contains the final report to the NASA Glenn Research Center (GRC) for the research project entitled Development, Implementation, and Application of Micromechanical Analysis Tools for Advanced High-Temperature Composites. The research supporting this initiative has been conducted by Dr. Brett A. Bednarcyk, a Senior Scientist at OM in Brookpark, Ohio from the period of August 1998 to March 2005. Most of the work summarized herein involved development, implementation, and application of enhancements and new capabilities for NASA GRC's Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC) software package. When the project began, this software was at a low TRL (3-4) and at release version 2.0. Due to this project, the TRL of MAC/GMC has been raised to 7 and two new versions (3.0 and 4.0) have been released. The most important accomplishments with respect to MAC/GMC are: (1) A multi-scale framework has been built around the software, enabling coupled design and analysis from the global structure scale down to the micro fiber-matrix scale; (2) The software has been expanded to analyze smart materials; (3) State-of-the-art micromechanics theories have been implemented and validated within the code; (4) The damage, failure, and lifing capabilities of the code have been expanded from a very limited state to a vast degree of functionality and utility; and (5) The user flexibility of the code has been significantly enhanced. MAC/GMC is now the premier code for design and analysis of advanced composite and smart materials. It is a candidate for the 2005 NASA Software of the Year Award. The work completed over the course of the project is summarized below on a year by year basis. All publications resulting from the project are listed at the end of this report.

Source record↗
NASA NTRS2012

Development of Field-Controlled Smart Optic Materials (ScN, AlN) with Rare Earth Dopants

The purpose of this investigation is to develop the fundamental materials and fabrication technology for field-controlled spectrally active optics that are essential for industry, NASA, and DOD applications such as: membrane optics, filters for LIDARs, windows for sensors, telescopes, spectroscopes, cameras, flat-panel displays, etc. ScN and AlN thin films were fabricated on c-axis Sapphire (0001) or quartz substrate with the RF and DC magnetron sputtering. The crystal structure of AlN in fcc (rocksalt) and hcp (wurtzite) were controlled. Advanced electrical characterizations were performed, including I-V and Hall Effect Measurement. ScN film has a free carrier density of 5.8 x 10(exp 20)/per cubic centimeter and a conductivity of 1.1 x 10(exp 3) per centimeter. The background ntype conductivity of as-grown ScN has enough free electrons that can readily interact with the photons. The high density of free electrons and relatively low mobility indicate that these films contain a high level of shallow donors as well as deep levels. Also, the UV-Vis spectrum of ScN and AlN thin films with rare earth elements (Er or Ho) were measured at room temperature. Their optical band gaps were estimated to be about 2.33eV and 2.24eV, respectively, which are obviously smaller than that of undoped thin film ScN (2.4eV). The red-shifted absorption onset gives direct evidence for the decrease of band gap (Eg) and the energy broadening of valence band states are attributable to the doping. As the doped elements enter the ScN crystal lattices, the localized band edge states form at the doped sites with a reduction of Eg. Using a variable angle spectroscopic ellipsometer, the decrease in refractive index with applied field is observed with a smaller shift in absorption coefficient.

Kim, Hyun-Jung↗
NASA NTRS2015

Smart Optical Material Characterization System and Method

Disclosed is a system and method for characterizing optical materials, using steps and equipment for generating a coherent laser light, filtering the light to remove high order spatial components, collecting the filtered light and forming a parallel light beam, splitting the parallel beam into a first direction and a second direction wherein the parallel beam travelling in the second direction travels toward the material sample so that the parallel beam passes through the sample, applying various physical quantities to the sample, reflecting the beam travelling in the first direction to produce a first reflected beam, reflecting the beam that passes through the sample to produce a second reflected beam that travels back through the sample, combining the second reflected beam after it travels back though the sample with the first reflected beam, sensing the light beam produced by combining the first and second reflected beams, and processing the sensed beam to determine sample characteristics and properties.

Choi, Sang Hyouk↗
NASA NTRS2016

Boeing Smart Rotor Full-scale Wind Tunnel Test Data Report

A full-scale helicopter smart material actuated rotor technology (SMART) rotor test was conducted in the USAF National Full-Scale Aerodynamics Complex 40- by 80-Foot Wind Tunnel at NASA Ames. The SMART rotor system is a five-bladed MD 902 bearingless rotor with active trailing-edge flaps. The flaps are actuated using piezoelectric actuators. Rotor performance, structural loads, and acoustic data were obtained over a wide range of rotor shaft angles of attack, thrust, and airspeeds. The primary test objective was to acquire unique validation data for the high-performance computing analyses developed under the Defense Advanced Research Project Agency (DARPA) Helicopter Quieting Program (HQP). Other research objectives included quantifying the ability of the on-blade flaps to achieve vibration reduction, rotor smoothing, and performance improvements. This data set of rotor performance and structural loads can be used for analytical and experimental comparison studies with other full-scale rotor systems and for analytical validation of computer simulation models. The purpose of this final data report is to document a comprehensive, highquality data set that includes only data points where the flap was actively controlled and each of the five flaps behaved in a similar manner.

Full-Scale Wind Tunnel↗
NASA NTRS2015

SMART Rotor Wind Tunnel Test Report

The Boeing Company, Mesa Arizona, has been developing smart material actuated rotor technology (SMART) under in-house, DARPA (Defense Advanced Research Projects Agency), NASA and Army funding. A whirl tower test of the SMART active flap rotor system was successfully conducted at the remote test facility (RTF) in Mesa, Arizona, in 2003. Under DARPA and NASA funding, the SMART rotor system was tested in the NASA Ames National Full Scale Aerodynamic Complex (NFAC) 40- by 80-Foot Wind Tunnel in 2008. The DARPA program objectives were to demonstrate the active flap impact on rotor acoustics in forward flight and establish a validation database for noise prediction tools. Under NASA funding, additional wind tunnel tests were conducted, with the objective to demonstrate and quantify vibration, noise, and performance improvements.Wind tunnel testing was successfully and safely concluded, meeting all high priority objectives. The authority, effectiveness, and reliability of the flap actuation system were demonstrated in 65 hours of testing at up to 155 knots and 7,700 pound thrust. Validation data was successfully acquired for four test conditions; blade loads were too high for the high speed condition. The effectiveness of the flap for noise and vibration control was demonstrated conclusively, with results showing significant reductions in BVI (Blade-Vortex Interaction) and in-plane noise as well as vibratory hub loads. The impact of the flap on control power and rotor smoothing was also demonstrated. Data evaluating any benefits in aerodynamic performance and impact on flight controls were acquired, but will need more detailed evaluation. Both open loop control and closed loop feedback control, using continuous time and higher harmonic controllers, were applied.The purpose of the Test Report is to provide a comprehensive document that describes the preparation for and conduct of the wind tunnel test and summarizes the processing and evaluation of wind tunnel test data for the DARPA and the NASA portion of the test. An overview of the wind tunnel test and results can be found in Reference 1. Details on the testing and results for BVI noise, in-plane noise, and vibrations can be found in References 2-4, respectively. These references are four papers, presented at the American Helicopter Society Annual Forum in 2009. A brief description of the delivered electronic data is provided in Reference 5.

Rotor↗
NASA NTRS1997

Dynamic Analysis of a Two Member Manipulator

Attenuating start-up and stopping vibrations when maneuvering large payloads attached to flexible manipulator systems is a great concern for many space missions. To address this concern, it was proposed that the use of smart materials, and their applications in smart structures, may provide an effective method of control for aerospace structures. In this paper, a modified finite element model has been developed to simulate the performance of piezoelectric ceramic actuators, and was applied to a flexible two-arm manipulator system. Connected to a control voltage, the piezoelectric actuators produce control moments based on the optimal control theory. The computer simulation modeled the end-effector vibration suppression of the NASA manipulator testbed for berthing operations of the Space Shuttle to the Space Station. The results of the simulation show that the bonded piezoelectric actuators can effectively suppress follow-up vibrations of the end-effector, stimulated by some external disturbance.

McGinley, W. Mark↗
NASA NTRS1997

Dynamic Analysis of a Two Member Manipulator Arm

Attenuating start-up and stopping vibrations when maneuvering large payloads attached to flexible manipulator systems is a great concern for many space missions. To address this concern, it was proposed that the use of smart materials, and their applications in smart structures, may provide an effective method of control for aerospace structures. In this paper, a modified finite element model has been developed to simulate the performance of piezoelectric ceramic actuators, and was applied to a flexible two-arm manipulator system. Connected to a control voltage, the piezoelectric actuators produce control moments based on the optimal control theory. The computer simulation modeled the end-effector vibration suppression of the NASA manipulator testbed for berthing operations of the Space Shuttle to the Space Station. The results of the simulation show that the bonded piezoelectric actuators can effectively suppress follow-up vibrations of the end-effector, stimulated by some external disturbance.

McGinley, Mark↗
NASA NTRS2003

Probabilistic Dynamic Buckling of Smart Composite Shells

A computational simulation method is presented to evaluate the deterministic and nondeterministic dynamic buckling of smart composite shells. The combined use of composite mechanics, finite element computer codes, and probabilistic analysis enable the effective assessment of the dynamic buckling load of smart composite shells. A universal plot is generated to estimate the dynamic buckling load of composite shells at various load rates and probabilities. The shell structure is also evaluated with smart fibers embedded in the plies right below the outer plies. The results show that, on the average, the use of smart fibers improved the shell buckling resistance by about 10 percent at different probabilities and delayed the buckling occurrence time. The probabilistic sensitivities results indicate that uncertainties in the fiber volume ratio and ply thickness have major effects on the buckling load while uncertainties in the electric field strength and smart material volume fraction have moderate effects. For the specific shell considered in this evaluation, the use of smart composite material is not recommended because the shell buckling resistance can be improved by simply re-arranging the orientation of the outer plies, as shown in the dynamic buckling analysis results presented in this report.

Abumeri, Galib H.↗
NASA NTRS2007

Probabilistic Dynamic Buckling of Smart Composite Shells

A computational simulation method is presented to evaluate the deterministic and nondeterministic dynamic buckling of smart composite shells. The combined use of intraply hybrid composite mechanics, finite element computer codes, and probabilistic analysis enable the effective assessment of the dynamic buckling load of smart composite shells. A universal plot is generated to estimate the dynamic buckling load of composite shells at various load rates and probabilities. The shell structure is also evaluated with smart fibers embedded in the plies right next to the outer plies. The results show that, on the average, the use of smart fibers improved the shell buckling resistance by about 10% at different probabilities and delayed the buckling occurrence time. The probabilistic sensitivities results indicate that uncertainties in the fiber volume ratio and ply thickness have major effects on the buckling load while uncertainties in the electric field strength and smart material volume fraction have moderate effects. For the specific shell considered in this evaluation, the use of smart composite material is not recommended because the shell buckling resistance can be improved by simply re-arranging the orientation of the outer plies, as shown in the dynamic buckling analysis results presented in this report.

Chamis, Christos C.↗
NASA NTRS2005

Potential High-Temperature Shape-Memory-Alloy Actuator Material Identified

Shape-memory alloys are unique "smart materials" that can be used in a wide variety of adaptive or "intelligent" components. Because of a martensitic solid-state phase transformation in these materials, they can display rather unusual mechanical properties including shape-memory behavior. This phenomenon occurs when the material is deformed at low temperatures (below the martensite finish temperature, Mf) and then heated through the martensite-to-austenite phase transformation. As the material is heated to the austenite finish temperature Af, it is able to recover its predeformed shape. If a bias is applied to the material as it tries to recover its original shape, work can be extracted from the shape-memory alloy as it transforms. Therefore, shape-memory alloys are being considered for compact solid-state actuation devices to replace hydraulic, pneumatic, or motor-driven systems.

Noebe, Ronald D.↗
NASA NTRS1998

Thermal Effects Modeling Developed for Smart Structures

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Lee, Ho-Jun↗
NASA NTRS2005

Materials Challenges in Space Exploration

United States civil space program administered by National Aeronautics and Space Administration (NASA) has a new strategic direction to explore the solar system. This new 'vision for space exploration' encompasses a broad range of human and robotic missions, including the Moon, Mars and destinations beyond. These missions require advanced systems and capabilities that will accelerate the development of many critical technologies, including advanced materials and structural concepts. Specifically, it is planned to develop high-peformance materials for vehicle structures, propulsion systems, and space suits; structural concepts for modular assembly for space infrastructure; lightweight deployable and inflatable structures for large space systems and crew habitats; and highly integrated structural systems and advanced thermal management systems for reducing launch mass and volume. This paper will present several materials challenges in advanced space systems-high performance structural and thermal materials, space durable materials, radiation protection materials, and nano- structural materials. The paper will also address smart materials and structures and examine space environmental effects on materials and methods of mitigating them. Finally, the paper will take a look at the possibility of utilizing materials in situ, i.e., processing and using desired materials on the surface of the Moon and Mars.

Bhat, Biliyar N.↗
NASA NTRS1991

Vibration suppression using smart structures

The control of structures for vibration suppression is discussed in the context of using smart materials and structures. Here the use of smart structures refers to using embedded piezoelectric devices as both control actuators and sensors. Using embedded sensors and actuators allows great improvements in performance over traditional structures (both passive and active) for vibration suppression. The application of smart structures to three experimental flexible structures is presented. The first is a flexible beam, the second is a flexible beam undergoing slewing motion, the third is a ribbed antenna. A simple model of a piezoelectric actuator/sensor is presented. The equations of motion for each structure is presented. The control issues considered as those associated with multi-input, multi-output control, PID control and LQR control implementation. A modern control analysis illustrates the usefulness of smart structures for vibration suppression.

Garcia, Ephrahim↗
DOE OSTI2023

Biobased Semi-Interpenetrating Polymer Networks of Poly(ε-caprolactone) and Epoxidized Soybean Oil with Nanoscale Morphology, Shape-Memory Effect, and Biocompatibility

Creating biobased polymer blends with outstanding properties, nanoscale morphology, shape-memory capability, and biocompatibility is very crucial and requires a fundamental understanding of the phase behavior, macromolecular structure, and biological compatibility of the polymer blends with living cells. It is very critical to understand the complex relationships among the polymer structure, morphology, and performance of multifunctional smart materials under conditions that they are likely to encounter during use, particularly in biomedical applications. Biobased semi-interpenetrating polymer networks of poly(ε-caprolactone) and epoxidized soybean oil with nanoscale morphology have been successfully synthesized via in situ cationic polymerization and compatibilization in a homogeneous solution. Varies analytical and characterization techniques, such as Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, transmission electron microscopy, X-ray scattering, cell toxicity, and shape-memory effects (SMEs), have been employed to understand the structure–properties relationship of these smart, biobased nanostructured polymer blends. The synthesized nano blends were nontoxic or biocompatible and supported attachment of human vein endothelial cells, showing their potential use in biomedical applications. The current versatile, low-cost strategy for synthesizing the nanoscale morphology of semi-interpenetrating polymer networks with SMEs and biocompatibility should be widely applicable for polymer systems. This study is also considered as a continuation to our efforts in the area of biobased polymers to develop innovative technologies to transform natural resources into smart multifunctional materials for a wide range of applications, including coatings, adhesives, and medical devices.

36 MATERIALS SCIENCE↗