Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composites dislocations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Strain-Mediated Sn Incorporation and Segregation in Compositionally Graded Ge 1– x Sn x Epilayers Grown by MBE at Different Temperatures

We investigated the process of Sn incorporation and surface segregation for compositionally graded Ge 1–x Sn x epilayers grown on high-quality Ge (001) substrates. Here, the growth resulted in pseudomorphic GeSn layers with a ~6% maximal Sn fraction at a constant substrate temperature. The maximal fraction of Sn was increased to 9.0% when the growth temperature was continuously lowered while increasing the Sn flux. The analysis of surface droplets and SIMS profiles of elemental composition give evidence of Sn rejection during the growth, potentially associated with a critical energy of elastic strain. The intentional reduction of the coherent strain by decreasing the Sn flux near the sample surface has been shown to trap a higher fraction of Sn in the Ge 1–x Sn x layer and lower surface segregation. Our results demonstrate that strain relief by misfit dislocations in the compositionally graded layer is inhibited, which leads to Sn segregation. Specifically, the compressive strain in the graded Ge 1–x Sn x epilayer is effectively “zero” near the interface with the Ge substrate and increases up to about –1.5 × 10 –2 near the surface. Thus, although the nucleation of a dislocation may reduce the compressive strain for the top region of the epilayer, it is not beneficial for the bottom region.

42 ENGINEERING↗

Large Area and Depth-Profiling Dislocation Imaging and Strain Analysis in Si/SiGe/Si Heterostructures

We demonstrate the combined use of large area depth-profiling dislocation imaging and quantitative composition and strain measurement for a strained Si/SiGe/Si sample based on nondestructive techniques of electron beam-induced current (EBIC) and X-ray diffraction reciprocal space mapping (XRD RSM). Depth and improved spatial resolution is achieved for dislocation imaging in EBIC by using different electron beam energies at a low temperature of ~7 K. Images recorded clearly show dislocations distributed in three regions of the sample: deep dislocation networks concentrated in the “strained” SiGe region, shallow misfit dislocations at the top Si/SiGe interface, and threading dislocations connecting the two regions. Dislocation densities at the top of the sample can be measured directly from the EBIC results. XRD RSM reveals separated peaks, allowing a quantitative measurement of composition and strain corresponding to different layers of different composition ratios. High-resolution scanning transmission electron microscopy cross-section analysis clearly shows the individual composition layers and the dislocation lines in the layers, which supports the EBIC and XRD RSM results.

36 MATERIALS SCIENCE↗

Review: mechanical behavior of metal/ceramic interfaces in nanolayered composites—experiments and modeling

In this study, recent experimental and modeling studies in nanolayered metal/ceramic composites are reviewed, with focus on the mechanical behaviors of metal/nitrides interfaces. The experimental and modeling studies of the slip systems in bulk TiN are reviewed first. Then, the experimental studies of interfaces, including co-deformation mechanism by micropillar compression tests, in situ TEM straining tests for the dynamic process of the co-deformation, thickness-dependent fracture behavior, and interrelationship among the interfacial bonding, microstructure, and mechanical response, are reviewed for the specific material systems of Al/TiN and Cu/TiN multilayers at nanoscale. The modeling studies reviewed cover first-principles density functional theory-based modeling, atomistic molecular dynamics simulations, and mesoscale modeling of nanolayered composites using discrete dislocation dynamics. The phase transformation between zinc-blende and wurtzite AlN phases in Al/AlN multilayers at nanoscale is also reviewed. Finally, a summary and perspective of possible research directions and challenges are given.

36 MATERIALS SCIENCE↗

Fluctuations and phase transitions in Larkin-Ovchinnikov liquid-crystal states of a population-imbalanced resonant Fermi gas

Motivated by a realization of imbalanced Feshbach-resonant atomic Fermi gases, we formulate a low-energy theory of the Fulde-Ferrell and the Larkin-Ovchinnikov (LO) states and use it to analyze fluctuations, stability, and phase transitions in these enigmatic finite momentum-paired superfluids. Focusing on the unidirectional LO pair-density-wave state, which spontaneously breaks the continuous rotational and translational symmetries, we show that it is characterized by two Goldstone modes, corresponding to a superfluid phase and a smectic phonon. Because of the liquid-crystalline ''softness'' of the latter, at finite temperature the three-dimensional state is characterized by a vanishing LO order parameter, quasi-Bragg peaks in the structure and momentum distribution functions, and a ''charge''-4, paired-Cooper-pairs, off-diagonal long-range order, with a superfluid-stiffness anisotropy that diverges near a transition into a nonsuperfluid state. In addition to conventional integer vortices and dislocations, the LO superfluid smectic exhibits composite half-integer vortex-dislocation defects. A proliferation of defects leads to a rich variety of descendant states, such as the charge-4 superfluid and Fermi-liquid nematics and topologically ordered nonsuperfluid states, that generically intervene between the LO state and the conventional superfluid and the polarized Fermi liquid at low and high imbalance, respectively. The fermionic sector of the LO gapless superconductor is also quite unique, exhibiting a Fermi surface of Bogoliubov quasiparticles associated with the Andreev band of states, localized on the array of the LO domain walls.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Impact of alloy composition on one-dimensional glide of small dislocation loops in concentrated solid solution alloys

One-dimensional glide of loops during ion irradiation at 773 K in a series of Ni-containing concentrated solid solution alloys has been observed directly during experiments conducted inside a transmission electron microscope. It was found that the frequency of the oscillatory motion of the loop, the loop glide velocity as well as the loop jump distance were dependent on the composition of the alloy and the size of the loop. Loop glide was most common for small loops and occurred more frequently in the less complex alloys, being highest in Ni, then NiCo, NiFe and NiCoFeCr. As a result, no measurable loop glide occurred in the NiCoCr, NiCoFeCrMn and NiCoFeCrPd alloys.

36 MATERIALS SCIENCE↗

On the origin of internal obstacles to dislocation glide in single-phase NiFe random alloys

Over the past decade, a new class of unconventional alloys, where several constitutive elements are presented in close to equal concentrations, is considered as promising structural materials in many applications. Properties and behavior of many concentrated solid solution alloys (CSSAs) under different conditions, including mechanical loading, differs from that of conventional alloys and has been the subject of intensive studies by different techniques. A key feature of these materials is that there is no clear distinction between solute and solvent species of atoms, which is the conventional approach to considering dislocation motion in alloys. To understand this regime, we have recently reported on the glide of a screw dislocation glide in a simple equiatomic NiFe alloy and reported the two-mode character. At low applied stress, the dislocation motion is similar to a glide through a field of obstacles. In this work, we report the results of a detailed study on the nature of these internal obstacles. We demonstrate that these are not conventional localized “obstacles” but is the result of significantly different energies of instantaneous dislocation configurations over the alloy bulk. The strong pinning positions are associated with composition changes in the partial dislocation cores, while observing no significant composition changes along the stacking faults. Local energies can vary significantly, as demonstrated using simulations of short-periodicity dislocation lines. Therefore, the critical stress to move a dislocation under such conditions is not a constant Peierls stress but represents a wide spectrum of barriers between different non-straight valleys that the dislocation line accommodates in the bulk at particular stress/strain conditions.

36 MATERIALS SCIENCE↗

Modeling the plastic relaxation onset in realistic SiGe islands on Si(001)

A detailed investigation of plastic relaxation onset in heteroepitaxial SiGe islands on Si(001) is presented. The strain field induced by a straight misfit-dislocation segment is modeled by finite-element-method (FEM) calculations in three dimensions, fully taking into account the interaction with the multifaceted free surfaces of realistic islands. The total elastic energies before and after the placement of a 60 deg. dislocation segment in the most favorable position are therefore evaluated by a full FEM approach, for different island sizes and compositions. The critical volumes with composition for inserting the dislocation are finally obtained and successfully compared with the data in a report by Marzegalli et al. [Phys. Rev. Lett. 99, 235505 (2007)], where experimental values are compared to a simpler approach.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Suppression of phase separation in AlGaInAs compositionally graded buffers for 1550 nm photovoltaic converters on GaAs

We investigate strategies to suppress phase separation and reduce threading dislocation density (TDD) in AlGaInAs compositionally graded buffers (CGBs) that span the lattice constant range from GaAs to InP. Combining the results from high resolution x-ray diffraction, cathodoluminescence, transmission electron microscopy, and photovoltaic device measurements, we correlate the choices of epitaxial growth conditions with the defect structure of the CGBs and subsequent device performance. Both the use of substrates with high misorientation off (100) toward the (111)A plane and Zn doping instead of Si doping are shown to suppress phase separation and reduce TDD. We demonstrate a 0.74 eV GaInAs device grown on a GaAs substrate offcut 19.5° toward (111)A using a Zn-doped AlGaInAs CGB with TDD = 3.5 ± 0.2 × 10 6 cm -2 that has a bandgap-open circuit voltage offset of only 0.434 V measured under the AM1.5G solar spectrum. We characterized this device under high-intensity irradiance from a 1570 nm laser and measured a 31.9% peak laser power conversion efficiency at 3.6 W/cm 2 irradiance. These results provide a roadmap to the manufacture of laser- and thermal-power conversion devices with the performance and cost-effectiveness needed to drive adoption of these technologies at scale.

14 SOLAR ENERGY↗

Influence of High Pulsed Magnetic Field on the Dislocations and Mechanical Properties of Al{sub 2}O{sub 3}/Al Composites

At T6 state, Al–Zn–Mg–Cu aluminum matrix composites reinforced with Al{sub 2}O{sub 3} particles generated in situ were subjected to high pulsed magnetic fields at different magnetic induction intensities (B = 2, 3 and 4 T). The results show that the dislocation densities in the treated samples increased with increasing B, and the magnetoplastic effect was determined to be the primary cause. The effect of the magnetic field is believed to alter the spin state of free electrons between dislocations and obstacles from the singlet state (associated with high bonding energy) to the triplet state (low bonding energy). The maximum ultimate tensile strength of 532 MPa was obtained at B = 4 T with 30 pulses, which was 20.7% higher than that of the initial sample, primarily because of dislocation strengthening. At B = 2 T, the elongation was at its maximum of 9.3%, representing an increase of 12% compared with the initial sample, while the associated ultimate tensile strength (447 MPa) was still higher than that of the untreated sample (440 MPa). The relationship between mechanical properties and microstructure was analyzed, and the improved properties observed in this work are explained by the transition of the electron spin state and the piling up of dislocations.

36 MATERIALS SCIENCE↗

In situ strain relaxation comparison between GaAsBi and GaInAs grown by molecular-beam epitaxy

The strain relaxation of GaAsBi is studied in order to determine both the maximum thickness before dislocations form for various misfits and the potential of GaAsBi for usage in the compositionally graded buffer of lattice-mismatched devices. Low-misfit GaAsBi epilayers are grown and compared with GaInAs, a well-studied material currently used in compositional grades. Relaxation behavior and dislocation energetics are compared using in situ wafer curvature. Samples are grown using molecular-beam epitaxy under similar conditions with misfit up to -0.81%. GaAsBi begins to relax at a lower thickness than GaInAs of the same mismatch. This leads to the majority of GaAsBi strain relaxation occurring with less material growth than comparable GaInAs. However, GaAsBi has greater residual strain than GaInAs after 2 {mu}m of growth. These results indicate that GaAsBi requires less elastic energy to form dislocations and more elastic energy to either encourage glide or multiply dislocations than GaInAs. GaAsBi shows less surface roughness than GaInAs for all samples, ruling out roughness as a source of dislocations and hindered glide in these alloys.

36 MATERIALS SCIENCE↗

MaRIE first experiments summaries version: May 9, 2010

A predictive understanding of microstructure-based heterogeneity and its consequences for materials damage & failure and phase transformation initiation is presently lacking. Most metallic materials used in applications are polycrystalline aggregates - individual single crystals separated by grain boundaries. Most of these materials are either metallic alloys or contain impurities. In either case, there is spatial variability in their chemical composition. These materials also contain dislocations which will be distributed in some way throughout the individual grains and increase in density with deformation and typically form dislocation sub-cell arrangements - producing spatial distribution in dislocation density. Many materials also produce twin or slip band structures with deformation which produce further heterogeneity within individual crystals. The objective of this first experiment is to probe the physics of dynamic solid-solid phase transformation and damage at length scales approaching those at which they nucleate in order to gain a detailed understanding of this process and the influence real material microstructure has on these events. These experiments would simultaneously be simulated by the appropriate modeling tools to further develop these predictive tools and to assist in our interpretation of experimental results.

36 MATERIALS SCIENCE↗

A Level Set Evaporation Model for Heterogeneous Atom Probe Tip

With the development of local electrode atom probe tomography (LEAP), the materials systems feasible for atomic structure determination has expanded from predominantly metals to include heterogeneous materials with complex structure and compositions. This makes the 3D atomic structure determination possible for most energy materials in battery, fuel cell, semiconductor, and nuclear applications. Atom probe tomography (APT) has been utilized to study multiphase materials with segregation and interface problems. The unique and quantitative information retrieved from APT can provide a foundation for the study of kinetic pathways, nanoscale composition mapping, multilayer interfacial segregation, dislocations and grain boundaries. However, a new challenge surfaces when the materials systems expand into heterogeneous materials: the traditional structure reconstruction introduces false magnification and large artifacts due to the underlying assumption of uniform and isotropic evaporation.

Atom probe, heterogeneous structure, evporation mo↗

Microstructural development in DED stainless steels: applying welding models to elucidate the impact of processing and alloy composition

Austenitic stainless steel microstructures produced by directed energy deposition (DED)are analogous to those developed during welding, particularly high energy density welding. To better understand microstructural development during DED, theories of microstructural evolution,which have been established to contextualize weld microstructures, are applied in this study to microstructural development in DED austenitic stainless steels. Phenomenological welding models that describe the development of oxide inclusions, compositional microsegregation, ferrite,matrix austenite grains, and dislocation substructures are utilized to clarify microstructural evolution during deposition of austenitic stainless steels. Two different alloys, 304L and 316L, arecompared to demonstrate the broad applicability of this framework for understanding microstmctural development during the DED process. Despite differences in grain morphology and solidification mode for these two alloys (which can be attributed to compositional differences),similar tensile properties are achieved. It is the fine-scale compositional segregation and dislocation structures that ultimately determine the strength of these materials. The evolution of microsegregation and dislocation structures is shown to be dependent on the rapid solidification and thermomechanical history of the DED processing method and not the composition of the starting material.

36 MATERIALS SCIENCE↗

Optimum high temperature strength of two-dimensional nanocomposites

High-temperature nanoindentation was used to reveal nano-layer size effects on the hardness of two-dimensional metallic nanocomposites. We report the existence of a critical layer thickness at which strength achieves optimal thermal stability. Transmission electron microscopy and theoretical bicrystal calculations show that this optimum arises due to a transition from thermally activated glide within the layers to dislocation transmission across the layers. We demonstrate experimentally that the atomic-scale properties of the interfaces profoundly affect this critical transition. The strong implications are that interfaces can be tuned to achieve an optimum in high temperature strength in layered nanocomposite structures.

36 MATERIALS SCIENCE↗

AI‐Driven Defect Engineering for Advanced Thermoelectric Materials

Thermoelectric materials offer a promising pathway to directly convert waste heat to electricity. However, achieving high performance remains challenging due to intrinsic trade-offs between electrical conductivity, the Seebeck coefficient, and thermal conductivity, which are further complicated by the presence of defects. This review explores how artificial intelligence (AI) and machine learning (ML) are transforming thermoelectric materials design. Advanced ML approaches including deep neural networks, graph-based models, and transformer architectures, integrated with high-throughput simulations and growing databases, effectively capture structure-property relationships in a complex multiscale defect space and overcome the “curse of dimensionality”. This review discusses AI-enhanced defect engineering strategies such as composition optimization, entropy and dislocation engineering, and grain boundary design, along with emerging inverse design techniques for generating materials with targeted properties. Finally, it outlines future opportunities in novel physics mechanisms and sustainability, highlighting the critical role of AI in accelerating the discovery of thermoelectric materials.

36 MATERIALS SCIENCE↗