ENVIRONMENTAL TESTING
Dynamic environments and environmental testing - shock and vibration testing
ENVIRONMENTAL TESTING↗
SEARCH · Engineering Papers
Results for “Shock testing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Shock Radiation Tests for Saturn and Uranus Entry Probes
This paper describes a test series in the Electric Arc Shock Tube at NASA Ames Research Center with the objective of quantifying shock-layer radiative heating magnitudes for future probe entries into Saturn and Uranus atmospheres. Normal shock waves are measured in Hydrogen/Helium mixtures (89:11 by mole) at freestream pressures between 13-66 Pa (0.1-0.5 Torr) and velocities from 20-30 km/s. No shock layer radiation is detected below 25 km/s, a finding consistent with predictions for Uranus entries. Between 25-30 km/s, radiance is quantified from the Vacuum Ultraviolet through Near Infrared, with focus on the Lyman-alpha and Balmer series lines of Hydrogen. Shock profiles are analyzed for electron number density and electronic state distribution. The shocks do not equilibrate over several cm, and distributions are demonstrated to be non-Boltzmann. Radiation data are compared to simulations of Decadal survey entries for Saturn and shown to be significantly lower than predicted with the Boltzmann radiation model.
Saturn Probe↗
Shock Radiation Tests for Saturn and Uranus Entry Probes
This paper describes a test series in the Electric Arc Shock Tube at NASA Ames Research Center with the objective of quantifying shock-layer radiative heating magnitudes for future probe entries into Saturn and Uranus atmospheres. Normal shock waves are measured in Hydrogen-Helium mixtures (89:11 by volume) at freestream pressures between 13-66 Pa (0.1-0.5 Torr) and velocities from 20-30 kms. No shock layer radiation is detected within measurement limits below 25 kms, a finding consistent with predictions for Uranus entries. Between 25-30 kms, radiance is quantified from the Vacuum Ultraviolet through Near Infrared, with focus on the Lyman-a and Balmer series lines of Hydrogen. Shock profiles are analyzed for electron number density and electronic state distribution. The shocks do not equilibrate over several cm, and in many cases the state distributions are non-Boltzmann. Radiation data are compared to simulations of Decadal Survey entries for Saturn and shown to be as much as 8x lower than predicted with the Boltzmann radiation model. Radiance is observed in front of the shock layer, the characteristics of which match the expected diffusion length.
Hydrogen↗
NASTRAN Analysis Comparison to Shock Tube Tests Used to Simulate Nuclear Overpressures
This report presents a study of the effectiveness of the NASTRAN computer code for predicting structural response to nuclear blast overpressures. NASTRAN's effectiveness is determined by comparing results against shock tube tests used to simulate nuclear overpressures. Seven panels of various configurations are compared in this study. Panel deflections are the criteria used to measure NASTRAN's effectiveness. This study is a result of needed improvements in the survivability/vulnerability analyses subjected to nuclear blast.
Wheless, T. K.↗
Pyrotechnic shock analysis and testing methods
Pyrotechnic shock analysis and testing methods for Ranger and Mariner spacecraft measurements
PYROTECHNICS↗
Hydrogen-Helium shock Radiation tests for Saturn Entry Probes
This paper describes the measurement of shock layer radiation in Hydrogen/Helium mixtures representative of that encountered by probes entering the Saturn atmosphere. Normal shock waves are measured in Hydrogen-Helium mixtures (89:11% by volume) at freestream pressures between 13-66 Pa (0.1-0.5 Torr) and velocities from 20-30 km/s. Radiance is quantified from the Vacuum Ultraviolet through Near Infrared. An induction time of several centimeters is observed where electron density and radiance remain well below equilibrium. Radiance is observed in front of the shock layer, the characteristics of which match the expected diffusion length of Hydrogen.
Shock Tube↗
Design and dynamic testing of an instrumented spacecraft component
Details relating to the design and subsequent vibration and shock tests of a spacecraft component for a severe vibration and shock environment are presented. The design process and analysis method involve the use of finite element analysis coupled with the Modal Strain Energy method with risk graphs to determine the adequacy of the design. The vibration levels experienced by box parts are reduced by the application of passive constrained layer viscoelastic treatments that significantly improve component reliability. All significant internal components were fully instrumented in both the random vibration and shock tests, the latter being done on a mechanical impact pyro simulator. Correlation between analysis and test data is good, validating the modeling and analysis techniques.
Dwyer, Thomas J.↗
Thermal Shock Behavior of Silicon Nitride Flexure Beam Specimens with Indentation Cracks
The experimental results of thermal shock testing of silicon nitride flexure beam specimens containing indentation cracks are presented. The thermal stress induced by water quenching is much greater in the transverse direction than in the longitudinal direction, resulting in an insensitivity of residual bend strength to temperature differences up to 580 C. This result indicates that a flexure beam configuration is not an appropriate geometry for thermal shock testing when thermal shock behavior is to be evaluated from residual bend strength data.
Choi, Sung R.↗
Recent test results on lithium BCX cells
Texts included: short circuit analysis, voltage reversal, high temperature exposure, parallel loading sharing, capacity tests, shock and vibration tests, and assembly tests. Both the AA and D cell configurations were tested. Certification of the cells is discussed and applications are highlighted.
Bragg, B. J.↗
Discharge of 1400 AH lithium thionyl chloride cells into voltage reversal
The development of a high energy density battery is discussed. Tests were conducted on a 1400 AH cell and they include: drop tests, crush tests, vibration and shock tests, hydrostatic pressure effects, charge current tests, and discharge tests. None of these tests led to a venting or explosion of the cell. Criteria are presented for extending RV safety of a 1400 AH cell.
Zolla, A. E.↗
Preliminary test results for Li-SOCl2 high-rate D cells
The performance and abuse characteristics of 55 D-size lithium-thionyl chloride (Li-SOCl2) cells are evaluated at relatively high rates. Results from the following tests are presented: shock test, vibration test, capacity performance, uninsulated short circuit, high temperature exposure, and overdischarge.
Bragg, Bobby J.↗
The USAF Phillips Laboratory sodium-sulfur battery technology program: Results and status
Tests performed on NaS batteries are reported. The results of safety and abuse testing, shock and vibration tests, cell failure on warm-up, freeze thaw, overtemperature conditions, electrolyte fracture, overdischarge, and short circuit tests are presented along with GEO and LEO cycle tests and the status of the NaS cell flight tests.
Rainbow, Marc E.↗
Entry, Descent, and Landing with Propulsive Deceleration: Supersonic Retropropulsion Wind Tunnel Testing and Shock Phenomena
The future exploration of the Solar System will require innovations in transportation and the use of entry, descent, and landing (EDL) systems at many planetary landing sites. The cost of space missions has always been prohibitive, and using the natural planetary and planet's moon atmospheres for entry, and descent can reduce the cost, mass, and complexity of these missions. This paper will describe some of the EDL ideas for planetary entry and survey the overall technologies for EDL that may be attractive for future Solar System missions. Future EDL systems may include an inflatable decelerator for the initial atmospheric entry and an additional supersonic retropropulsion (SRP) rocket system for the final soft landing. A three engine retropropulsion configuration with a 2.5 in. diameter sphere-cone aeroshell model was tested in the NASA Glenn Research Center's 1- by 1-ft (1×1) Supersonic Wind Tunnel (SWT). The testing was conducted to identify potential blockage issues in the tunnel, and visualize the rocket flow and shock interactions during supersonic and hypersonic entry conditions. Earlier experimental testing of a 70deg Viking-like (sphere-cone) aeroshell was conducted as a baseline for testing of a SRP system. This baseline testing defined the flow field around the aeroshell and from this comparative baseline data, retropropulsion options will be assessed. Images and analyses from the SWT testing with 300- and 500-psia rocket engine chamber pressures are presented here. In addition, special topics of electromagnetic interference with retropropulsion induced shock waves and retropropulsion for Earth launched booster recovery are also addressed.
Palaszewski, Bryan↗
Entry, Descent, and Landing with Propulsive Deceleration: Supersonic Retropropulsion Wind Tunnel Testing and Shock Phenomena
The future exploration of the Solar System will require innovations in transportation and the use of entry, descent, and landing (EDL) systems at many planetary landing sites. The cost of space missions has always been prohibitive, and using the natural planetary and planet's moon atmospheres for entry, and descent can reduce the cost, mass, and complexity of these missions. This paper will describe some of the EDL ideas for planetary entry and survey the overall technologies for EDL that may be attractive for future Solar System missions. Future EDL systems may include an inflatable decelerator for the initial atmospheric entry and an additional supersonic retro-propulsion (SRP) rocket system for the final soft landing. A three engine retro-propulsion configuration with a 2.5 inch diameter sphere-cone aeroshell model was tested in the NASA Glenn 1x1 Supersonic Wind Tunnel (SWT). The testing was conducted to identify potential blockage issues in the tunnel, and visualize the rocket flow and shock interactions during supersonic and hypersonic entry conditions. Earlier experimental testing of a 70 degree Viking-like (sphere-cone) aeroshell was conducted as a baseline for testing of a supersonic retro-propulsion system. This baseline testing defined the flow field around the aeroshell and from this comparative baseline data, retro-propulsion options will be assessed. Images and analyses from the SWT testing with 300- and 500-psia rocket engine chamber pressures are presented here. In addition, special topics of electromagnetic interference with retro-propulsion induced shock waves and retro-propulsion for Earth launched booster recovery are also addressed.
Palaszewski, Bryan↗
Noncoplanar magnetic fields at collisionless shocks - A test of a new approach
The expressions derived by Jones and Ellison (1987) (JE) for the spatial integral of the noncoplanar field component in a fast-mode collisionless shock and for the magnitudes of the magnetic-field rotation and potential drop difference are evaluated on the basis of ISEE 1 and 2 observations in the earth bow shock and numerical simulations using the hybrid code of Leroy et al. (1981 and 1982). The data and simulation results are presented graphically and shown to be consistent with the JE hypothesis, that the rotation and drop difference are due to unequal electron and ion masses. The rotations and potential drop differences predicted by the JE equations, however, are found to be accurate only for subcritical shocks at low Mach numbers; the underestimation of the values for hypercritical shocks is attributed to neglect of the ion current from reflected gyrating ions.
Gosling, J. T.↗
A hypersonic shock tunnel test of the Aeroassist Flight Experiment (AFE) vehicle at high altitude test conditions
The Aeroassist Flight Experiment (AFE) vehicle is a 4.26 m-diameter raked and blunted elliptic cone that is intended to obtain aerodynamic and aerothermodynamic data on blunt bodies at velocities near 10 km/s and altitudes above 75 km. Previous wind tunnel tests of this configuration have been at Mach numbers of 10 or lower. The present test program consisted of five test conditions at Mach numbers between 15 and 20 and simulated altitudes from 75 km to 97 km. Static longitudinal aerodynamic coefficients, the lift-to-drag ratio, and the trim angle-of-attack were obtained for angles-of-attack between 7 deg and 27 deg. The effects of angle-of-attack and shock Reynolds number, Re2, have been studied. These results indicate the AFE configuration is longitudinally stable. The variation of normal force slope, CNalpha and lift-to-drag slope, (L/D)alpha as well as the trim angle-of-attack with Re2 are documented. The trim angle-of-attack increases with decreasing values of shock Reynolds number (increasing altitude) while the lift-to-drag ratio at the trimmed conditions is relatively constant.
Wittliff, C. E.↗
Aerospace systems pyrotechnic shock data /ground test and flight/. Volume 6 - Pyrotechnic shock design guidelines manual, revision A Final report, Jun. 1968 - Mar. 1970
Design of structures and equipment to reduce shock loads induced by pyrotechnics and explosive devices - Vol. 6
Kacena, W. J., III↗
Induced shock pulse testing by transient waveform control
A method of synthesizing an arbitrarily shaped transient time pulse on vibration exciters is described. The transient waveform control technique is based on recent developments in digital time series analysis, the real-time FFT processor. A brief description of the theory, error estimates and hardware/software implementation to the JPL Dynamic Environmental Testing Laboratory is presented.
Kim, B. K.↗