Engineering PapersSearch

SEARCH · Engineering Papers

Results for “Interface state”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

A study of charged particles/radiation damage to VLSI device materials

Future spacecraft systems such as the manned space station will be subjected to low-dose long term radiation particles. Most electronic systems are affected by such particles. There is therefore a great need to understand device physics and failure mechanisms affected by radiation and to design circuits that would be less susceptible to radiation. Using 2 MeV electron radiation and bias temperature aging, it was found that MOS capacitors that were prepositively biased have lower flatband voltage shift and lesser increase in density of surface state charge than those that were not prepositively biased. In addition, it was shown that there is continued recovery of flatband voltage and density of state charge in irradiated capacitors during both room temperature anneal and 137 degree anneal. When nMOS transistors were subjected to 1 MeV proton radiation, charge pumping and current versus voltage measurements indicated that transconductance degradation, threshold voltage shifts and changes in interface states density may be the primary cause of nMOS transistor failure after radiation. Simulation studies using SPICE were performed on CMOS SRAM cells of various transistor sizes. It is shown that transistor sizing affects the noise margins of CMOS SRAM cells, and that as the beta ratio of the transistors of the CMOS SRAM cell decreases, the effective noise margin of the SRAM cell increases. Some suggestions were made in connection with the design of CMOS SRAMS that are hardened against single event upsets.

Okyere, John G.

Role of photocurrent in low-temperature photoemission studies of Schottky-barrier formation

Photoelectron spectroscopy is frequently used to study band bending in semiconductors due to charge stored in surface or interface states. This paper examines how such experimental results are modified by photovoltages generated within the band-bending region not only by ambient light sources, but by the incident X-rays themselves. Recent experiments which have suggested dopant-dependent and reversible temperature-dependent band bending in the initial stages of formation of the metal-GaAs(110) interface are used as an example. It is shown that the reported dependence derives from a photovoltaic effect.

Hecht, M. H.

Effect of gamma-ray irradiation on the surface states of MOS tunnel junctions

Gamma-ray irradiation with doses up to 8 megarad produces no significant change on either the C(V) or the G(V) characteristics of MOS tunnel junctions with intermediate oxide thicknesses (40-60 A), whereas the expected flat-band shift toward negative electrode voltages occurs in control thick oxide capacitors. A simple tunneling model would explain the results if the radiation-generated hole traps are assumed to lie below the valence band of the silicon. The experiments also suggest that the observed radiation-generated interface states in conventional MOS devices are not due to the radiation damage of the silicon surface.

Ma, T. P.

Thermally-restorable optical degradation and the mechanism of current transport in Cu2S-CdS photovoltaic cells

The photovoltaic properties of single-crystal Cu2S-CdS heterojunctions have been investigated as a function of heat treatment by detailed measurements of the dependence of short-circuit current on photon energy, temperature, and the state of optical degradation or enhancement. A coherent picture is formulated for the relationship between enhancement and optical degradation, and their effect on the transport of short-circuit photoexcited current and dark, forward-bias current in the cell. Optical degradation in the Cu2S-CdS cell is shown to be closely identical to optical degradation of lifetime in a homogeneous CdS:Cd:Cu crystal, indicating that the CdS:Cu layer near the junction interface controls carrier transport in the cell. It is proposed that both the photoexcited short-circuit current and the dark, forward-bias current are controlled by a tunneling-recombination process through interface states.

Fahrenbruch, A. L.

Development of InSb charge-coupled infrared imaging devices: Linear imager

The following results were accomplished in the development of charge coupled infrared imaging devices: (1) a four-phase overlapping gate with 9 transfers (2-bits) and 1.0-mil gate lengths was successfully operated, (2) the measured transfer efficiency of 0.975 for this device is in excellent agreement with predictions for the reduced gate length device, (3) mask revisions of the channel stop metal on the 8582 mask have been carried out with the result being a large increase in the dc yield of the tested devices, (4) partial optical sensitivity to chopped blackbody radiation was observed for an 8582 9-bit imager, (5) analytical consideration of the modulation transfer function degradation caused by transfer inefficiency in the CCD registers was presented, and (6) for larger array lengths or for the insertion of isolated bits between sensors, improvements in InSb fabrication technology with corresponding decrease in the interface state density are required.

Phillips, J. D.

Computer analysis of heterojunction and graded bandgap solar cells

The development and application of a graded bandgap solar cell computer analysis program is discussed. The basic device equations as used in the computer analysis are discussed and the techniques used to model material parameter variations are described. Finally, the results of the computer analysis of several Al(x)Ga(1-x)As and GaAs(1-x)P(x) solar cell structures are presented along with a discussion of the effects of interface states and various composition profiles on maximum solar cell efficiency.

Sutherland, J. E.

MIS diode structure in As/+/ implanted CdS

Structure made by As implantation of carefully prepared high-conductivity CdS surfaces followed by Pt deposition and 450 C anneal display rectifying, although substantially different, I-V characteristics in the dark and during illumination with subband-gap light. Structures prepared in the same way on an unimplanted portion of the substrate have similar I-V characteristics, except that the forward turnover voltage for an illuminated unimplanted diode is much smaller than that for an implanted diode. It is suggested that the charge conduction in both structures is dominated by hole and/or electron tunneling through a metal-semiconductor potential barrier. The tunneling processes appear to be quite sensitive to subband-gap illumination, which causes the dramatic decreases of turnover voltages and apparent series resistances. The difference in turnover voltage appears to be caused by interface states between the Pt electrode and the implanted layer, which suggests a MIS model.

Hutchby, J. A.

LaF3 insulators for MIS structures

Thin films of LaF3 deposited on Si or GaAs substrates have been observed to form blocking contacts with very high capacitances. This results in comparatively hysteresis-free and sharp C-V (capacitance-voltage) characteristics for MIS structures. Such structures have been used to study the interface states of GaAs with increased resolution and to construct improved photocapacitive infrared detectors.

Sher, A.

Ge photocapacitive MIS infrared detectors

An undoped Ge photocapacitive detector is reported which has peak normalized detectivities at wavelengh 1.4 microns and chopping frequencies 13-1000 Hz of 9 x 10 to the 12th, 4 x 10 to the 9th cm Hz to the 1/2th/W operating respectively at temperatures 77, 195, and 295 K. The observed temperature, spectral, and frequency response of the signal and noise are explained in terms of the measured space charge and interface state properties of the device.

Binari, S. C.

Frequency response of charge transfer in MOS inversion layers

The dynamics of charge transfer from a reservoir into an MOS inversion layer, which limits the frequency response of an MOS transistor or a charge-coupled device, is investigated. Using Berman and Kerr's model of space-charge capacitance in the semiconductor, a small-signal distributed model is developed for an MOS structure which transfers charge in an inversion channel due to a variation in the gate voltage. The dynamics of the charge transfer is characterized by a time constant which is determined by the length of the inversion channel and its mobility. Experimental data of gate capacitance vs frequency, taken from a test structure with a diffused source/drain well, are satisfactorily fitted by theoretical curves derived from the model. The channel mobility is precisely determined from the adjusted time constant. The influence of interface states on the capacitance-frequency relationship is also briefly discussed.

Lieneweg, U.

Theory of extrinsic and intrinsic heterojunctions in thermal equilibrium

A careful analysis of an abrupt heterojunction consisting of two distinct semiconductors either intrinsic or extrinsic is presented. The calculations apply to a one-dimensional, nondegenerate structure. Taking into account all appropriate boundary conditions, it is shown that the intrinsic Fermi level shows a discontinuity at the interface between the two materials which leads to a discontinuity of the valence band edge equal to the difference in the band gap energies of the two materials. The conduction band edge stays continuous however. This result is independent of possible charged interface states and in sharp contrast to the Anderson model. The reasons for this discrepancy are discussed.

Von Ross, O.

Radiation-induced defects in SiO2 as determined with XPS

An analytical method based on oxide/substrate intensity ratios is used to deduce the product of the atomic number density and electron mean free path as a function of depth, for the cases of device-quality gate oxides grown on Si substrates and irradiated with zero to 20 eV electrons during in situ X-ray photoelectron spectroscopy. These structures had been thinned stepwise to 25-60 A by means of a wet chemical depth-profiling procedure. Si(3+) species are formed in the Si/SiO2 interface region, and their observation during their relaxation and annihilation is correlated with strained Si-O-Si bonds. The observation of bond of cleavage and bond strain gradients in these samples is used to extend silica devitrification models for the explanation of fixed oxide charge generation and interface states.

Grunthaner, F. J.

Carbon, oxygen and their interaction with intrinsic point defects in solar silicon ribbon material: A speculative approach

Some background information on intrinsic point defects is provided and on carbon and oxygen in silicon in so far as it may be relevant for the efficiency of solar cells fabricated from EFG ribbon material. The co-precipitation of carbon and oxygen and especially of carbon and silicon self interstitials are discussed. A simple model for the electrical activity of carbon-self-interstitial agglomerates is presented. The self-interstitial content of these agglomerates is assumed to determine their electrical activity and that both compressive stresses (high self-interstitial content) and tensile stresses (low self-interstitial content) give rise to electrical activity of the agglomerates. The self-interstitial content of these carbon-related agglomerates may be reduced by an appropriate high temperature treatment and enhanced by a supersaturation of self-interstitials generated during formation of the p-n junction of solar cells. Oxygen present in supersaturation in carbon-rich silicon may be induced to form SiO, precipitates by self-interstitials generated during phosphorus diffusion. It is proposed that the SiO2-Si interface of the precipates gives rise to a continuum of donor stables and that these interface states are responsible for at least part of the light inhancement effects observed in oxygen containing EFG silicon after phosphorus diffusion.

Goesele, U.

Electron trapping in rad-hard RCA IC's irradiated with electrons and gamma rays

Enhanced electron trapping has been observed in n-channels of rad-hard CMOS devices due to electron and gamma-ray irradiation. Room-temperature annealing results in a positive shift in the threshold potential far beyond its initial value. The slope of the annealing curve immediately after irradiation was found to depend strongly on the gate bias applied during irradiation. Some dependence was also observed on the electron dose rate. No clear dependence on energy and shielding over a delidded device was observed. The threshold shift is probably due to electron trapping at the radiation-induced interface states and tunneling of electrons through the oxide-silicon energy barrier to fill the radiation-induced electron traps. A mathematical analysis, based on two parallel annealing kinetics, hole annealing and electron trapping, is applied to the data for various electron dose rates.

Danchenko, V.

The effect of processing conditions on the GaAs/plasma-grown insulator interface

The effect of processing conditions on the interface state density was evaluated from C-V measurements on metal-oxide-semiconductor capacitors. The optimum processing conditions for the minimum surface state density was found to be related to the postoxidation annealing temperature and time, and was independent of chemical treatments prior to oxidation. Annealing at the optimum condition (i.e., at 350 C for 1 h in either nitrogen or hydrogen gas, with or without an aluminum pattern on the oxide) reduces the fast surface state density by about one order of magnitude. By using a nitrogen/oxygen plasma, the static dielectric constant of the oxide decreased as the N/O ratio was increased, and nitrogen was incorporated into the oxide. In addition, the fast surface state density was reduced as a result of this nitridation process.

Hshieh, F. I.

1986 Annual Conference on Nuclear and Space Radiation Effects, 23rd, Providence, RI, July 21-23, 1986, Proceedings

The present conference on the effects of nuclear and space radiation on electronic hardware gives attention to topics in the basic mechanisms of radiation effects, dosimetry and energy-dependent effects, electronic device radiation hardness assurance, SOI/SOS radiation effects, spacecraft charging and space radiation, IC radiation effects and hardening, single-event upset (SEU) phenomena and hardening, and EMP/SGEMP/IEMP phenomena. Specific treatments encompass the generation of interface states by ionizing radiation in very thin MOS oxides, the microdosimetry of meson energy deposited on 1-micron sites in Si, total dose radiation and engineering studies, plasma interactions with biased concentrator solar cells, the transient imprint memory effect in MOS memories, mechanisms leading to SEU, and the vaporization and breakdown of thin columns of water.

Ellis, Thomas D.

Frequency-dependent characteristics and trap studies of lattice-matched (x = 0.53) and strained (x greater than 0.53) In(0.52)Al(0.48)As/In(x)Ga(1-x)As HEMT's

The low-frequency characteristics of InAlAs/In(x)Ga(1-x)As high-electron-mobility transistors (HEMTs) are studied, and trap densities are evaluated. The HEMTs' transconductance g(m) and output resistance R(ds) dispersion are smallest for 60 percent indium (In) content and largest for 53 percent In. The maximum dispersion for the 53 percent In sample is about 6 percent for g(m) and about 13.3 percent for R(ds), corresponding to lower values than observed in MESFETs. The R(ds) dispersion characteristics are weaker than in AlGaAs/GaAs HEMTs and manifest themselves primarily up to 100 kHz. An analysis of the dispersion results indicates that, unlike in the case of MESFETs, the channel region under the gate rather than the access regions is responsible for the dispersion. Interface state densities were extracted by the AC conductance method and were found to follow the same trend as the g(m) and R(ds) dispersion.

Ng, Geok-Ing

Plasma Deposited SiO2 for Planar Self-Aligned Gate Metal-Insulator-Semiconductor Field Effect Transistors on Semi-Insulating InP

Metal-insulator-semiconductor (MIS) field effect transistors were fabricated on InP substrates using a planar self-aligned gate process. A 700-1000 A gate insulator of Si02 doped with phosphorus was deposited by a direct plasma enhanced chemical vapor deposition at 400 mTorr, 275 C, 5 W, and power density of 8.5 MW/sq cm. High frequency capacitance-voltage measurements were taken on MIS capacitors which have been subjected to a 700 C anneal and an interface state density of lxl0(exp 11)/eV/cq cm was found. Current-voltage measurements of the capacitors show a breakdown voltage of 107 V/cm and a insulator resistivity of 10(exp 14) omega cm. Transistors were fabricated on semi-insulating InP using a standard planar self-aligned gate process in which the gate insulator was subjected to an ion implantation activation anneal of 700 C. MIS field effect transistors gave a maximum extrinsic transconductance of 23 mS/mm for a gate length of 3 microns. The drain current drift saturated at 87.5% of the initial current, while reaching to within 1% of the saturated value after only 1x10(exp 3). This is the first reported viable planar InP self-aligned gate transistor process reported to date.

Tabory, Charles N.