Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Creep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Effects of Geometric Discontinuities on Creep Behavior of Alloy 617

Due to the excellent long-term high-temperature performance of Alloy 617, the Alloy has been identified as the primary structural material for the intermediate heat exchanger of the Very High Temperature Reactor (VHTR). Both the base and welded alloy has been qualified to be used up to 950 °C up to 100,000 hours by the American Society of Mechanical Engineer (ASME) Boiler and Pressure Vessel Code (BPVC). The qualification properties of the material were exclusively determined by uniaxial creep tests. The components may, however, experience multiaxial stress conditions in service due to the reactor geometry. This study used notched creep tests to investigate the effect of geometric discontinuities on creep behavior of both the base and welded Alloy 617. The V-notch tests reveal that the geometric discontinuities do not reduce the creep rupture live under high and intermediate stress conditions. The U-notch tests show that a larger radius notch behave in a similar way as a straight gauge section of a uniaxial test. The creep rupture live of the welded alloy was slightly longer than the base metal.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Inhomogeneous Distribution and Coarsening of y″ Precipitates in a Ni-Based Superalloy and Their Effect on Creep

It has been reported that the addition of Nb or Ta in the high Ti/Al ratio alloys promotes the formation of y″ precipitates solely and greatly contributes to the elevated temperature strength and resistance to creep deformation. In this study, the y''-dominant INCONEL alloy 725 (IN725) variants (named M725-Nb/Ta) modified with a high level of Nb/Ta additions and high Ti/Al ratio was chosen as a model alloy for microstructural observation of y'' variants upon creep. Following the high temperature aging (HTA), y'' was found to be the main strengthening precipitate with no detectable y’ in both M725 alloys. After creep, the grip/gage sections of the crept M725-Nb/Ta exhibited preferential coarsening and inhomogeneous distribution of y''. That is, one or two of the variants were preferentially coarsened at the expense of another variant, and sandwich-like structures, comprising of cubic y′ precipitates with small y″ discs on each face, were formed. This variant selection behavior taking place in the grip section with no stress applied was different from the typical stress-induced variant selection in previous literature. However, the sample with prior high temperature exposure (700 °C for 500 hours) with varying y″ characteristics demonstrated a similar trend of creep when compared with those in the HTA sample, suggesting that the coarsening and the inhomogeneous distribution of y'' was not the determinant of creep life in bulk M725-Nb/Ta alloys.

Hung, Chang-Yu↗
DOE OSTI2025

Creep Deformation and Damage Mechanisms in an Advanced High-Temperature Additively Manufactured Nickel-Base Superalloy

Abstract This research investigates the processing–structure–properties–performance relationship in a novel nickel-base superalloy, ABD ® -900AM, designed for extreme environments. Specifically tailored for additive manufacturing (AM), ABD ® -900AM maintains mechanical integrity at high temperatures and is comparable to other nickel-based superalloys with a 30–40% gamma-prime volume fraction. A comprehensive study was conducted using laser-beam powder bed fusion and electron-beam powder bed fusion methods. Factors such as heat treatment, porosity, build orientation, and hot isostatic pressing were evaluated to understand their effects on microstructure and mechanical performance. Microstructural characterization revealed significant differences in grain size and orientation across build processes and heat treatments. High-temperature mechanical testing indicated that grain size, heat treatment, and orientation significantly influence creep behavior. A super-solvus heat treatment led to recrystallization and grain growth, significantly improving creep properties compared to a near-solvus heat treatment. Various creep mechanisms were identified across different conditions, and creep rupture models were developed for each build process. Post-test microstructural analysis showed grain boundary damage, with differences in creep cavitation morphology under varying stress conditions. It was shown that MC carbides grow at the expense of gamma-prime near grain boundaries, leading to precipitate-free zones in specimens tested at higher temperatures. This study fills a significant gap in fundamental research by offering a deeper insight into the high-temperature mechanical behavior of additively manufactured nickel-base superalloys. It also explores critical research questions regarding the role of carbides and the significance of heat treatment. The insights gained enhance confidence in the industry adoption of ABD ® -900AM and similar alloys for high-temperature applications, bridging the knowledge gap and supporting the development of reliable AM processes for extreme environments.

Bridges, Alex (ORCID:000000030338759X)↗
DOE OSTI2025

Hayward Fault Creep From Coda Wave Interferometry

Understanding creep is essential for assessing seismic hazards along the creeping Hayward Fault, which threatens the San Francisco area. Current 1-D monitoring methods, like creepmeters and theodolites, provide limited measurements with low spatial resolution. InSAR offers higher 2-D spatial sampling but lower temporal resolution. We introduce a novel method using coda wave interferometry (CWI) to monitor creep in 2-D with high resolution. By calculating changes in ambient seismic noise travel times, we relate these measurements to creep offsets, bridging the gap between existing methods. Applied to seismic data from 2021 around the Hayward Fault, our CWI-derived offsets aligned with creepmeter measurements, revealing continuous and episodic creep. A 2-D regionalization identified a spatial boundary between these regimes, corroborating previous findings. This approach could enhance seismic monitoring and improve understanding of fault mechanics and earthquake risks.

Luckie, Thomas William [Sandia National Laboratori↗
DOE OSTI2024

Creep Degradation of Austenitic Steels in CO2 Environments

Steels have a proven track record of safe operation in steam power plants for decades. Interest in developing supercritical CO2 power cycles as a more efficient and sustainable alternative to steam cycles has driven a need to understand steel performance in these new environments. In particular, the potential of the high temperature CO2 environment to influence the creep behavior of the steel must be determined. Prior research on this topic between the 1960s and 1980s found conflicting conclusions, but nevertheless raised the possibility that carburization during CO2 exposure may strongly affect the creep behavior. This raises concerns particularly for thin-sectioned components such as compact heat exchangers, where even small rates of carburization can become problematic over long operating lifetimes. To shed light on this issue, this research investigates the creep behavior of austenitic stainless steel 347H and 309H (a higher Cr alternative) at 650°C. Specimens of 0.5, 1.0, and 2.0 mm thickness were tested to further assess the effect of steel thickness. Both steels show a reduction in creep life in CO2 relative to air, with 309H showing slightly better performance than 374H. Analysis is ongoing to determine the reason for degraded creep properties.

Rozman, Kyle A.↗
DOE OSTI2025

Simulation of Creep Deformation and Failure in Graded AM Microstructures

This report describes modeling tools and techniques developed to simulate the long-term material performance of 316H stainless steel manufactured using Laser Powder Bed Fusion (LPBF). A physics-based Crystal Plasticity Finite Element model is used to simulate creep in microstructures and to study the roles of grain morphology, porosity, and texture. We describe our modeling methodology, including an orientation-mapping technique to capture the spatially varying crystallographic orientation that results from the build conditions. Our study of microstructural features shows that AM microstructures produced by LPBF tend to creep faster in the build direction, while texture and grain boundaries strengthen the transverse directions. However, when grain-boundary porosity and the consequent cavity growth are included in the model, the transverse directions begin to creep faster. In examining texture, the results indicate that spatially varying orientation arising from the build conditions increases anisotropy in the material, making it critical to account for orientation gradients in the material to accurately model its mechanical behavior. We also describe a material-model calibration campaign in which we calibrated the constitutive model specifically for LPBF 316H stainless steel at 725℃ for both solution-annealed and as-built conditions. Finally, these tools and techniques are used to model creep in microstructures representing different regions of an LPBF material with graded microstructure, owing to intentional variation in processing conditions. The creep simulation results show good agreement with experimental data across all three microstructures, with future work planned to study rupture in the material.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Creep Property of Intermetallic Dispersive Steels for Nuclear Applications

To meet the materials performance demands of next-generation nuclear and high-temperature energy systems, a new class of intermetallic-dispersive steels (IDS) has been designed through integrated computational thermodynamics and alloy design strategies. The IDS alloys incorporate coherent L1₂ (γ′-Ni₃Al) nanoprecipitates within an Fe–Ni–Cr austenitic matrix, engineered to achieve both high temperature strength and thermodynamic stability while suppressing the formation of detrimental δ-Ni₃Nb and η-Ni₃Ti phases. Initial creep testing of Ti-IDS and TiTa-IDS alloys demonstrates rupture lives comparable to or exceeding those of Inconel 718 and ODS steels, despite being fabricated through conventional ingot metallurgy. Step-load creep tests identified a stress threshold near 300–350 MPa for the onset of tertiary creep, and in-situ neutron diffraction experiments on Ti-IDS revealed clear load partitioning between the matrix and γ′ precipitates: elastic strain is shared by both phases, while plastic strain localizes in the matrix. These results confirm that stable γ′–matrix interfaces play a dominant role in retarding dislocation motion and enhancing creep resistance. In FY26, the program will conduct repeat creep rupture testing of TiTa-IDS at 650 °C/400 MPa, initiate long-term rupture testing of TiNb-IDS, and perform TEM-based microstructural characterization to elucidate dislocation–precipitate interactions and microstructural stability. Collectively, these efforts will establish the mechanistic foundation for next-generation high-temperature structural materials based on the IDS concept.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Creep Resistant Martensitic Steels for Operation at High-Temperatures in Power Generation Applications

Increasing the temperature capabilities of ferritic/martensitic 9-12% Cr steels can help in increasing the operating temperature of land-based turbines and minimize the use of expensive high-temperature alloys in the hot section. A creep resistant martensitic steel, JMP, was developed with the potential to operate at or above 650°C. The design of the alloys originated from computational modeling for phase stability and precipitate strengthening using fifteen constituent elements. Cobalt was used for increased solid solution strengthening, Si for oxidation resistance and different W and Mo concentrations for matrix strength and stability. The JMP steels showed increases in creep life compared to MARBN/SAVE12AD at 650°C for testing at various stresses between 138 MPa and 207 MPa. On a Larson-Miller plot, the performance of the JMP steels surpasses that of state-of-the-art MARBN steel. Approximately 21 years of cumulative creep data are reported for the JMP steels which encompasses various compositions. The relationships between composition-microstructure-creep properties are discussed including characterization of microstructures after >20,000 hours in creep.

Detrois, Martin↗
DOE OSTI2024

Creep behavior of austenitic steels in CO2 and the effect of specimen thickness

Steels have a proven track record of safe operation in steam power plants for decades. Interest in developing supercritical CO2 power cycles as a more efficient and sustainable alternative to steam cycles has driven a need to understand steel performance in these new environments. In particular, the potential of the high temperature CO2 environment to influence the creep behavior of the steel must be determined. Prior research on this topic between the 1960s and 1980s found conflicting conclusions, but nevertheless raised the possibility that carburization during CO2 exposure may strongly affect the creep behavior. This raises concerns particularly for thin-sectioned components such as compact heat exchangers, where even small rates of carburization can become problematic over long operating lifetimes. To shed light on this issue, this research investigates the creep behavior of austenitic stainless steel 347H and 309H (a higher Cr alternative) at 650°C. Specimens of 0.5, 1.0, and 2.0 mm thickness were tested to further assess the effect of steel thickness. Both steels show a reduction in creep life in CO2 relative to air, with 309H showing slightly better performance than 374H. Analysis is ongoing to determine the reason for degraded creep properties.

Rozman, Kyle A.↗
DOE OSTI2024

Creep-Fatigue Properties of Additional 316H PM-HIP Materials Fabricated from Different Powder Compositions and Processing Routes

The process of powder metallurgy (PM) hot isostatic pressing (HIP) works by consolidating powdered materials at relatively high temperature and pressure to form near-net-shaped components. Ideally, PM-HIP production methods can reduce component lead time and improve designs for high-temperature reactors and/or microreactors. To introduce PM-HIP into Section III, Division 5 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, it is necessary to show adequate material properties regarding creep, high-temperature low-cycle fatigue, and creep fatigue. However, prior work has shown that the creep-fatigue cycles to failure for PM-HIP 316H stainless steel are greatly reduced compared to the conventional, wrought product. This work continued creep-fatigue analysis on a 316H stainless steel with lower oxygen and nitrogen contents and at different HIP parameters than previously analyzed. The objective was to better understand what is causing the reduced PM-HIP 316H performance so improvements can be made PM-HIP 316H creep-fatigue lifetimes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Fatigue Performance of an Improved Creep Strength 10%Cr Steel

The deployment of 9-12% Cr steels for elevated temperature applications up to 650 °C presents a cost-effective alternative to more expensive nickel-based alloys in steam turbine power generation. To enhance creep resistance at this temperature range, a novel ferritic-martensitic steel, designated CPJ7, was developed and fabricated at the National Energy Technology Laboratory. The alloy design aimed to mitigate the transformation of strengthening carbides into deleterious phases that degrade creep performance. Results have demonstrated that CPJ7 exhibits favorable creep and oxidation resistance at 650 °C. However, its fatigue performance remains unexplored. This study builds upon prior research by evaluating the low cycle fatigue behavior of CPJ7 and verifying that modifications beneficial to creep performance were not detrimental to the fatigue performance. The alloy was tested at both 650 °C and ambient temperature under fully reversed bending conditions (R = − 1) and a load ratio of 0.05. Furthermore, the alloy exhibits cyclic softening, a behavior consistent with other 9-10 wt.% Cr steels. Analysis of the microstructure and hysteresis loops further corroborate cyclic softening mechanisms typical of ferritic-martensitic steels. Overall, the fatigue performance of CPJ7 meets or exceeds that of P91 steel, demonstrating its potential for high-temperature structural applications.

9% Cr ferritic-martensitic steel↗
DOE OSTI2024

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗
DOE OSTI2025

Step-loaded creep testing of Zircaloy-4 cladding at higher temperatures in the α-phase

A refined understanding of zirconium-based cladding thermomechanical performance during rapid transients is essential for enhancing the safety and operation of light-water reactors. Traditional models for zirconium alloys under accident conditions generally assume that creep dominates fuel cladding performance. Here, these historic models have largely remained unchanged and serve as the basis for safety criteria development. As the U.S. nuclear industry pursues higher burnup levels, the increased release of fission gases during transients raises the risk of cladding failure in the low-temperature hcp α-phase, making the fidelity of these models of greater importance. Creep testing was conducted from 550–700°C with 25–120 MPa applied hoop stresses to investigate Zircaloy-4 deformation at accident-relevant temperatures in the α-phase. Step-loading was employed to capture creep behavior across a wide stress range from a single sample. The stress-strain rate data at higher temperatures (650 and 700°C) were well-described by isotropic versions of the Erbacher and Kaddour models, while the lower temperature data (550 and 600°C) were underpredicted by both anisotropic and isotropic model variants. Greater strain rates during the initial loading step at 650 and 700°C were attributed to recrystallization and grain growth of sub-micron crystallites. Yet, texture analysis revealed the basal split texture remained after testing. These observations produced results suggesting Zircaloy-4 claddings experience higher creep rates across the α-phase than previously thought, possibly related to dynamic anisotropy due to temperature dependent activation of deformation mechanisms, effects of biaxial loading, and variation in material condition between the current testing used in previous model development.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Nucleation rate controlled grain boundary and lattice creep

Nucleation versus diffusion rate-limited bicrystal and single crystal creep exhibit different scaling dependencies that enable the mechanisms to be isolated when measured as a function of sample size. It has recently been suggested that nucleation rate-limited kinetic models generally describe the non-Newtonian portion of the creep response well, but more direct evidence is required. This work analyzes the grain boundary creep response of UO 2 , a pyrochlore high entropy oxide, silver, and palladium, along with the lattice creep of silver using small-scale in situ loading in the transmission electron microscope. At small sizes, each system exhibits scale dependence associated with nucleation rate-limited kinetics. Fits of the data produce activation volumes on the order of a few Burgers vectors cubed with positive temperature coefficients as expected for nucleation kinetics. The activation enthalpies fall in the range of about 0.4 eV to 1.7 eV, being lower for the metals and higher for the oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Physics-Informed Machine Learning Model for Ceramic Matrix Composite Creep

A physics-informed recurrent neural network (RNN) based surrogate model is developed to emulate the nonlinear, time-dependent constitutive behavior of ceramic matrix composites (CMCs) driven by matrix damage and constituent creep at the microscale. Physics-informed constraints are introduced into the surrogate model through regularization to ground the prediction in physics and improve its predictive capabilities. Training data is generated using the high-fidelity generalized method of cells (HFGMC) approach which calls appropriate creep and damage models for each of the constituents. This coupling permits simulating the nonlinear behavior of CMCs based on constituent response at the microscale along with microstructural features such as fiber and porosity volume fraction and fiber radius. The microscale repeating unit cell is loaded under creep fatigue conditions to replicate the material loading experienced in a turbine engine. Therefore, the RNN-based surrogate model is tasked with predicting, as a function of variable input stress sequence, temperature, and microstructural features, the resulting strain history response while satisfying physical constraints related to creep rate, isochoric inelastic deformation, and strain energy density. The trained surrogate model is shown to effectively match the strain history over quantified distributions of microstructural features and relevant loading regimes and temperatures. Neural network based surrogate models can offer efficient alternatives to running computationally intensive multiscale material models to simulate the nonlinear response of large structural models. Therefore, the presented work provides evidence towards the feasibility of developing, training, and running such models for CMCs with complex microstructures, nonlinear time-dependent material response, and under non-monotonic loading conditions.

ceramic matrix composites↗
DOE OSTI2025

Rationalization of the tensile creep behavior of the Nb45Ta25Ti15Hf15 bcc refractory complex concentrated alloy using Rao-Suzuki screw dislocation glide model

Published experimental tensile creep data for refractory body-centered cubic alloy Nb45Ta25Ti15Hf15 (NTTH) at temperatures ranging from 850–950 °C and applied tensile stresses 50–300 MPa are analyzed using the Rao-Suzuki screw dislocation glide model of solid solution strengthening. It is shown that the experimental creep data as well as transmission electron microscopy observations of post- creep deformation dislocation microstructure are in agreement with the model results. This suggests that the creep deformation of NTTH at 850–950 °C is controlled by screw dislocation glide.

Rao, Satish I↗
DOE OSTI2024

Microstructural evaluation of the creep behavior in L-PBF Ni-based superalloys

This presentation at ICAM 2024 Conference focuses on the commonalities and differences in the creep rupture behavior and creep mechanisms for three distinct classes of laser powder-bed fusion (L-PBF) Ni-based superalloys (γ’-precipitate strengthened Haynes® 282®, γ’/γ”/δ-precipitate strengthened Alloy 718, and solid-solution strengthened Alloy 625) as compared to conventionally processed counterparts. A comparison of Larson-Miller parameter plots establishes that these alloys perform statistically within the bounds established for the wrought product, despite having dissimilar microstructural features and other artefacts associated with PBF-LB manufacturing and post-processing heat treatment. To understand the failure and the impact of composition, minor phases, and deformation defects on creep behavior, the fractography has been performed and microstructures have been evaluated in detail with SEM-EDS, EBSD, and HAADF-STEM. The underlying diffusional and dislocation creep mechanisms associated with this microstructural evaluation is discussed. This work is supported by NETL-FWP-1022408 Advanced Turbines.

Sudbrack, Chantal↗
DOE OSTI2024

Measure the effect of molten halide salt exposure on creep rupture lifetime

Recent resurgence in the research and commercial interests in molten salt reactors (MSRs) as a viable advanced reactor concept to achieve the short- and long-term climate goals has resulted in ongoing efforts to demonstrate their commercial potential. These are relying on a combination of the extensive legacy knowledge from the molten salt reactor experiment (MSRE) and relatively recent data on materials compatibility of structural materials of interest such as 316H in molten salts environments. However, there is a critical lack of data on the mechanical behavior of alloys of interest for MSRS such as 316H, 617 and 709 in molten fluoride (FLiNaK or FLiBe) or chloride (NaCl-MgCl 2 ) salts. Limited legacy data from the molten salt reactor experiment (MSRE) program showed a significant reduction in creep rupture strength of a Ni-base alloy (Ni-15Cr-7Fe wt.%) in the molten fluoride NaF-ZrF4-UF4 (50-46-4 mol.%) salt. With ongoing efforts to commercialize different molten salt reactor concepts, the industry can considerably benefit from quantitative information on the impact of molten halide salts on the engineering properties such as creep and fatigue strength of materials of interest. Creep tests for 316H were conducted with fluoride (FLiNaK) and chloride (NaCl-MgCl 2 ) salts tat 650°C/150 MPa while alloys 709 and 617 were tested with FLiNaK at 700C/158 MPa and 750C.146 MPa respectively. Baseline tests were conducted in air to assess the impact of the molten salts on the creep behavior.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗