Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Contact impedance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructural Passivation of Patterned Al 2 O 3 Back Contacts on CdS/CdTe Solar Cells

Abstract Patterned aluminum oxide (Al 2 O 3 ) back contact on cadmium telluride (CdTe) solar cells can effectively mitigate the loss of the majority carriers while retaining the passivation benefits for minority carriers. This study investigates the impact of the point‐contact geometry on cell performance, where the spacing of the microholes is systematically varied at a constant microhole diameter (≈16 µm). Microhole arrays are created on an evaporated Al 2 O 3 layer (≈30 nm) on CdTe using laser‐beam lithography and selective wet etching processes. Comparative analysis indicates a significant decrease in fill factor (FF) and short‐circuit current ( I SC ) when the contact fraction falls below 30%, likely due to the Al 2 O 3 barrier impeding majority carriers. Above this fraction, FF and I SC are comparable to those of baseline CdTe cells without Al 2 O 3 . Open‐circuit voltage ( V OC ) shows a gradual decrease as Al 2 O 3 coverage is reduced but exhibits a slight increase (<15 mV) when the contact fraction exceeds 30%. Cathodoluminescence (CL) characterization reveals that significantly improved radiative recombination occurs within the CdTe grain bulk with Al 2 O 3 , whereas this effect on grain boundaries is minimal. The findings imply complex local carrier dynamics in the patterned back‐contact region, closely tied to the microstructural properties of CdTe‐based solar cells.

Roy, Etee Kawna↗
DOE OSTI2023

Structural and electrochemical evolution of alloy interfacial layers in anode-free solid-state batteries

“Anode-free” solid-state batteries feature high energy density since there is no anode active material. Although the beneficial effects of interfacial layers at the anode-solid electrolyte interface have been demonstrated, the mechanisms through which they influence lithium plating/stripping are unclear. Here, in this study, we reveal the evolution of 100-nm silver and gold interfacial layers during lithium plating/stripping using electrochemical methods, electron microscopy, X-ray microcomputed tomography, and modeling. The alloy layers improve Coulombic efficiency and resistance to short circuiting, even though the alloys form solute regions or particulates that detach from the current collector during plating. In situ electrochemical impedance spectroscopy shows that the alloys return to the interface and mitigate contact loss at the end of stripping, avoiding a critical vulnerability of anode-free cells. Contact retention is driven by even Li thickness that promotes spatially uniform stripping, as well as local alloy delithiation in response to current concentrations that homogenizes current and diminishes voiding.

25 ENERGY STORAGE↗
DOE OSTI2022

HIV-1 CD4-binding site germline antibody–Env structures inform vaccine design

BG24, a VRC01-class broadly neutralizing antibody (bNAb) against HIV-1 Env with relatively few somatic hypermutations (SHMs), represents a promising target for vaccine strategies to elicit CD4-binding site (CD4bs) bNAbs. To understand how SHMs correlate with BG24 neutralization of HIV-1, we report 4.1 Å and 3.4 Å single-particle cryo-EM structures of two inferred germline (iGL) BG24 precursors complexed with engineered Env-based immunogens lacking CD4bs N-glycans. Structures reveal critical Env contacts by BG24 iGL and identify antibody light chain structural features that impede Env recognition. In addition, biochemical data and cryo-EM structures of BG24 iGL variants bound to Envs with CD4bs glycans present provide insights into N-glycan accommodation, including structural modes of light chain adaptations in the presence of the N276 gp120 glycan. Together, these findings reveal Env regions critical for germline antibody recognition and potential sites to alter in immunogen design.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Application of the van der Pauw method for electrical conductivity measurements at high temperatures using an insulating compressing ring

High quality data on the high temperature electrical properties of ceramics, particularly oxides, is of great value for material selection, design, and modeling for a broad range of emerging applications. Utilizing the mismatch in the coefficient of thermal expansion between two materials, a purely mechanical method for establishing electrical contact in the van der Pauw geometry to measure the bulk resistivity of ceramic disks at high temperatures is presented. Measurements of a reference material, 20 mol. % Gd-doped cerium oxide, are presented up to 1000 °C. The viability of electrical measurements up to a maximum temperature of 1600 °C is also considered. Measurements are performed using multiple techniques and compared to literature values finding excellent agreement. Finally, the approach described in this work enables the van der Pauw method to be applied to many ceramic materials over a wide range of temperatures and environments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Atomic- and Molecular-Scale Interphase Engineering for High-Performance Solid-State Batteries

Solid-state batteries (SSBs) promise a decisive advance beyond conventional Li-ion systems, yet their development remains constrained by persistent solid–solid interfacial instabilities that degrade performance and durability. Interfaces between solid electrolytes and both cathodes and Li metal often exhibit poor wettability, limited physical contact, and high charge–transfer resistance, leading to chemical decomposition, mechanical failure, and impedance growth. Overcoming these limitations requires interphase engineering with atomic-scale precision—capabilities that conventional coating methods cannot reliably deliver. Atomic layer deposition (ALD) and molecular layer deposition (MLD) uniquely meet this need by enabling ultrathin, conformal, and composition-tunable films that stabilize reactive surfaces, suppress parasitic reactions, and regulate Li-metal morphology. Importantly, this Perspective highlights ALD/MLD systems that have already demonstrated effectiveness in liquid-electrolyte cells and discusses how these validated strategies can be deliberately translated to solid-state architectures. By grounding future directions in experimentally proven concepts rather than speculative hypotheses, we outline how atomic- and molecular-scale design principles can accelerate the development of robust, high-performance SSB technologies.

atomic and molecular layer deposition↗
DOE OSTI2020

Non-contact electrochemical evaluation of biofilms

Abstract Here, we demonstrate a non-contact technique for electrochemical evaluation of biofilms on surfaces in relation to corrosion. Electrochemical impedance spectrometry was employed, incorporating flat patterned electrodes positioned over the surfaces of aluminum and glass with and without biofilms. Signal communication from the working electrode to the counter electrode followed electric field lines passing tangentially through the biofilms. Electrochemical impedance parameters that were evaluated included complex impedance, phase angle, imaginary (out of phase) conductivity and Cole–Cole plots with a corresponding equivalent circuit. Changes in the impedance properties due to the presence of biofilms were monitored and correlated through microbiological, chemical and electrochemical assays. Impedance parameters associated with microbial activity correlated with biofilms on aluminum and glass surfaces. This technical approach provides impedance information about the biofilm without the signal traveling through the underlying conductive media or disrupting the biofilm. In this way, biological contributions to surface fouling can be evaluated with minimal contribution from the inorganic surface under the biofilm. In addition, this technique can be used to monitor biofilms on electrochemically inert surfaces as well as electrically conductive surfaces. Graphic abstract

Turick, Charles E. (ORCID:0000000307815846)↗
DOE OSTI2024

High-current, high-voltage AlN Schottky barrier diodes

AlN Schottky barrier diodes with low ideality factor (<1.2), low differential ON-resistance (<0.6 mΩ cm 2 ), high current density (>5 kA cm −2 ), and high breakdown voltage (680 V) are reported. The device structure consisted of a two-layer, quasi-vertical design with a lightly doped AlN drift layer and a highly doped Al 0.75 Ga 0.25 N ohmic contact layer grown on AlN substrates. A combination of simulation, current–voltage measurements, and impedance spectroscopy analysis revealed that the AlN/AlGaN interface introduces a parasitic electron barrier due to the conduction band offset between the two materials. This barrier was found to limit the forward current in fabricated diodes. Further, we show that introducing a compositionally-graded layer between the AlN and the AlGaN reduces the interfacial barrier and increases the forward current density of fabricated diodes by a factor of 10 4 .

Quiñones, C. E. (ORCID:0000000192703747)↗
DOE OSTI2022

Kilauea Magnetotelluric Dataset

In 2002 and 2003 a collaborative effort was undertaken between Lawrence Berkeley National Laboratory, Sandia National Laboratories, the USGS Menlo Park, the USGS Hawaiian Volcano Observatory, and Electromagnetic Instruments Inc. to study the Kilauea volcano in Hawaii using the magnetotelluric (MT) technique. The work was motivated by a desire to improve understanding of the magma reservoirs and conduits within Kilauea and the East and Southwest Rift zones, which has implications for understanding Kilaueas plumbing system. An improved understanding of the rift zones has implications in understanding large-scale landslides that are generated in the Hilina Slump, which produce significant impacts on coastal communities. Up to eight stations operated simultaneously, with multiple remote reference sites, and data were processed using multi-station robust processing techniques. In total, data were acquired at 70 sites over the Southwest and East rift zones. Good to excellent quality data were obtained even in the harshest conditions, such as those encountered on the fresh lava flows of the East Rift Zone (ERZ), where electrical contact resistances are on the order of 100 kOhm. This data supports the continuing efforts to increase geothermal power on the island of Hawaii. Each of the 70 EDI files are the MT impedance tensors for 1 site. There is also a description of the processing of the data and a site map showing the locations of each site.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Understanding the Mechanisms of Self-Organization in Atmospheric Pressure DC Glows

One of the most challenging areas in atmospheric pressure plasmas is controlling uniformity and contact area. Indeed it is this problem which is closely related to scale up that has impeded the widespread applications of these plasmas. The atmospheric pressure plasma glow is a type of atmospheric pressure discharge akin to a traditional low pressure glow particularly when compared with discharge morphology. But this is where the similarities end. Unlike low pressure glows, atmospheric pressure glows do not rely on electrode processes such as secondary electron emission to make the discharge self-sustaining, rather the discharge is sustained by typically processes such as the presence of a resistive layer or through favorable atomic collisional processes such as that which prevail in helium that stabilizes the discharge so that the thermal instability is mitigated. These discharges can feature either solid metal electrodes or geometries where at least one electrode is a liquid water electrolyte. Regardless of the implementation, DC 1 Atm glows are fascinating in that the plasma attachment under certain conditions can self-organize. The attachment surface area therefore changes as a result. Therefore, self-organization could be the key to optimizing plasma contact area and thereby open the door to applications in the real world. The plasma physical processes prevailing at the surface where the self-organization takes place remain largely unexplored. There is very little published research on the conditions that prevail at the surface and virtually no scholarship on measured plasma parameters of the self-organized attachments themselves or the surface electric field. This effort breaks new ground by elucidating these largely unexplored physical processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Electrophoretic Deposition of Platinum Nanoparticles using Ethanol-Water Mixtures Significantly Reduces Neural Electrode Impedance

We report platinum electrodes are critical components in many biomedical devices, an important example being implantable neural stimulation or recording electrodes. However, upon implantation, scar tissue forms around the electrode surface, causing unwanted deterioration of the electrical contact. We demonstrate that sub-monolayer coatings of platinum nanoparticles (PtNPs) applied to 3D neural electrodes by electrophoretic deposition (EPD) can enhance the electrode's active surface area and significantly lower its impedance. In this work we use ethanol-water mixtures as the EPD solvent, in contrast to our previous studies carried out in water. We show that EPD coating in 30 vol.% ethanol improves the device's electrochemical performance. Computational mesoscale multiparticle simulations were for the first time applied to PtNP-on-Pt EPD, revealing correlations between ethanol concentration, electrochemical properties, and coating homogeneity. Thereto, this optimum ethanol concentration (30 vol.%) balances two opposing trends: (i) the addition of ethanol reduces water splitting and gas bubble formation, which benefits surface coverage, and (ii) increased viscosity and reduced permittivity occur at high ethanol concentrations, which impair the coating quality and favoring clustering. A seven-fold increase in active surface area and significantly reduced in vitro impedance of the nano-modified neural stimulation electrode surfaces highlight the influence of ethanol-water mixtures in PtNP EPD.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Atomic layer deposited aluminum nitride for interface protection of lithium germanium thiophosphate solid electrolytes

Lithium germanium thiophosphate (LGPS) is an attractive solid-state electrolyte material due to its exceptionally high ionic conductivity (~1.2 × 10 –2 S cm –1 ), comparable to many organic liquid electrolytes commonly used in batteries. Despite the high conductivity of LGPS, the susceptibility of LGPS to deleterious degradation reactions has impeded its commercial adoption into solid-state batteries. In particular, the poor voltage stability of LGPS with high-voltage cathode or lithium metal potentials often results in dramatically increasing cell impedance during galvanic cycling. Here, we use aluminum nitride (AlN) as a protection layer for Li metal anode, applied directly to the LGPS at 250 °C using plasma-enhanced atomic layer deposition, to enhance cell performance by preventing LGPS-Li metal reactions. We compare the surface chemistry and electrochemical cycling performance of atomic layer-deposited AlN grown using both plasma N 2 and NH 3 precursors. Galvanostatic cycling and electrochemical impedance spectroscopy show that AlN-coated LGPS cells perform better than bare LGPS cells in contact with Li metal anodes, with the AlN able to improve cycling longevity by over a factor of 3 in certain cases. Finally, we utilize x-ray photoelectron spectroscopy (XPS) line scans to highlight the slow room-temperature reactivity between AlN and evaporated lithium metal, and a computational model is built to aid further XPS analysis.

25 ENERGY STORAGE↗
DOE OSTI2022

Contact Resistance of Carbon–Li x (Ni,Mn,Co)O 2 Interfaces

Abstract Electronic resistance in lithium‐ion battery positive electrodes is typically attributed to the bulk resistance of the active material and the network resistance of the carbon additive. Expected overpotentials from these bulk components are minimal relative to that from charge‐transfer resistance. However, literature reports show that cell overpotentials are often much more sensitive to conductive additives than the expected level from bulk or percolating‐network transport. This discrepancy motivated a detailed examination of the contact resistance between the active material and conductive additive. The contact and bulk resistances are simultaneously measured using dense bar samples of lithium‐layered oxides (Li x Ni 1 /3 Mn 1/3 Co 1/3 O 2 and Li x Ni 0.5 Mn 0.3 Co 0.2 O 2 ) in contact with carbon black. It is found that the contact resistance dominates the overall electronic resistance when the length scale is smaller than millimeters; after correcting for contact effects, bulk conductivity of layered oxides is determined to be orders‐of‐magnitude higher than previously reported. In porous electrodes, it is found from three‐electrode electrochemical impedance spectroscopy that the carbon content most heavily influences the low‐frequency regime (≈0.01 Hz), as opposed to the high frequency (>10 3 Hz) regime expected from electronic percolating properties. Constriction effects within the layered oxide are identified as the dominant mechanism for contact resistance and its implication is investigated for porous electrodes.

Kuo, Jimmy Jiahong↗
DOE OSTI2022

Characterization of Engineered Pinholes in Dielectric Stacks of High-Performance Poly-Silicon Passivating Contacts

Passivating contact structures are expected to be implemented in > 50 % of industrially manufactured silicon photovoltaics produced over the next decade. One type of passivating contact utilizes a c-Si/dielectric/doped poly-Si layer stack. In cases where the dielectric layer/s are thick enough to impede tunneling of charge carriers, it was shown that disruptions (pinholes) in the dielectric are required to facilitate transport.[1] Pinholes in SiOx layers have typically been formed via high temperature annealing that allows localized breakup of this layer. This approach has drawbacks; 1) high temperature annealing increases cost and 2) pinhole formation is sensitive to both the SiOx thickness and wafer surface morphology making control of density and dimensions difficult. Recently, an alternative method of pinhole formation relying on metal assisted chemical etching (MACE) was shown to allow control over pinhole areal densities.[2] Such control is critical as both the density and dimensions of the pinholes determine saturation current density and contact resistivity. The contacts formed with the MACE process are known as polysilicon on locally etched oxide or PLEO and also result in low saturation current densities and low contact resistivity due to SiOx passivation and engineered pinhole enabled charge carrier transport, respectively. Photovoltaic devices with efficiencies greater than 20 % have recently been produced with these contacts, demonstrating the viability of contacts with engineered pinholes. Experimentally, preferential local collection of excess charge carriers has been observed and definitively connected to thermally induced pinholes in thick SiOx layers within c-Si/SiOx/poly-Si contact structures.[3] Recent work has shown that enhanced local collection of excess carriers can result from enhanced diffusion of dopants through pinholes in SiOx layers.[4] This study was restricted to simulation and characterization of poly-Si with the same dopant type as the c-Si substrates. In this work we focus our analysis on boron doped poly-Si with different stacks of dielectric layers (PLEO and PLENO where the N refers to a SiNy layer on top of the SiOx) on n-type crystalline silicon. This provides insight into how engineered pinholes affect charge collection across the p-n junction. Like previous observations of locally enhanced carrier transport through thermally induced pinholes, the EBIC images in Figure 1 shows that engineered pinholes in PLENO (1a) and PLEO (1b) also exhibit locally enhanced carrier transport at pinhole locations (bright spots in the images). We will also present detailed correlative nanoscale structural and chemical analysis using TEM imaging and EELS analysis with sample preparation guided by EBIC imaging. This allows us to connect the density and dimensions of engineered pinholes with charge carrier transport and measured photovoltaic device parameters. Our findings will accelerate the adoption of PLEO and PLENO contacts in industrially manufactured photovoltaic devices.

EBIC↗
DOE OSTI2021

Lanthanum Strontium Cobaltite-Alumina Fiber Composite Contact Material for Solid Oxide Fuel Cells

Short alumina fibers were added to LSCo contact material to enhance the contact strength and improve thermal cycle stability. Alumina fiber from 2.5 v% to 20 v% were mixed with LSCo and sintered at elevated temperatures. Sintering study showed retardation in densification of LSCo matrix with increasing alumina content. Sintered bulk strength exhibited similar behavior where strength greatly reduced at high alumina v%. Coefficient of thermal expansion showed consistent results with prediction from rule of mixture. Contact strength using anode supported YSZ bilayer coupons improved greatly with the presence of small amount (2.5-5 v%) alumina fibers and no substantial reduction after 10 deep thermal cycles. Candidate LSCo-Al2O3 contact materials was validated in a generic stack test fixture for 1000h at 800oC followed by 10 thermal cycles. Results of impedance analysis showed substantial improvement in thermal cycle stability as compared to LSCo parent materials.

SOFC cathode, strength, LSCo, alumina↗
DOE OSTI2024

Evaluating Pressure‐dependent Discharge Behavior of Foil Versus In situ Plated Lithium Metal Anodes in Solid‐State Batteries

Abstract Anode‐free manufacturing of solid‐state batteries (SSBs) shows promise to maximize energy density by eliminating excess lithium (Li) and simplifying battery production. However, high reversibility during discharge (stripping of Li) is necessary for long‐lifetime SSBs with a limited Li reservoir. Further, the plastic flow of Li changes depending on the Li thickness, leading to possible differences in discharge performance under stack pressure. This work investigates the pressure‐dependent discharge performance of anode‐free manufactured SSBs with in situ plated Li and compares the performance to that of conventional thick Li foil cells. Distinct stripping behavior is observed at low pressures (0–1 MPa), where Li diffusivity and initial interfacial contact may control accessible capacity, compared to high pressures (3–10 MPa) where mechanical deformation of Li likely governs stripping behavior. Analysis of impedance spectra collected during stripping shows that additional stack pressure delays the formation of deep, as opposed to lateral, voids in the Li anode. These results provide insights to guide the transition from thick Li foil anodes to anode‐free manufactured SSBs.

Haslam, Catherine G.↗
DOE OSTI2024

Effect of H + Exchange and Surface Impurities on Bulk and Interfacial Electrochemistry of Garnet Solid Electrolytes

Contact loss and current constriction pose significant challenges at the Li metal interface of solid-state batteries. For garnet-structured Li 7 La 3 Zr 2 O 12 (LLZO), these effects are amplified by Li + /H + exchange and surface contamination reactions, which lead to conductivity losses and poor Li wetting. In this study, we utilize a variety of surface treatment processes across 37 cells to selectively induce proton exchange and contamination reactions in LLZO. The resulting bulk and surface chemistry is systematically characterized and correlated to changes in electrochemical properties. Additionally, we combine impedance analysis and finite element method modeling to deconvolute sources of impedance contributions at the Li metal interface. Specifically, we show that constriction impedance at the Li metal interface arises not solely from voids, but also from ionically-resistive surface contaminants. Further, these findings emphasize the connection between ionic conductivity and constriction, demonstrating that micron-scale ionically-resistive components increase constriction even with identical contact geometries. Finally, we leverage our comprehensive dataset to highlight unstable overpotential growth as a failure mechanism, additionally showing that the phase of a cell’s impedance is a sensitive indicator for the onset of interfacial instability. Overall, this study clarifies the impacts of proton exchange and surface contamination on electrochemical properties at the Li|solid electrolyte interface and elucidates insights that are generalizable to other solid-state battery systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Sulfonated Diels–Alder Poly(Phenylene)s in Membrane Electrode Assemblies for Fuel Cells

The transition to environmentally sustainable materials in fuel cells requires alternatives to persistent polyfluoroalkyl substances (PFAS) like Nafion. This study investigates the performance-limiting factors of membrane electrode assemblies (MEAs) utilizing sulfonated Diels–Alder poly(phenylene)s (sDAPPs) as PFAS-free polymer electrolytes. Among the configurations evaluated, the greatest performance loss occurred when sDAPP is used as the cathode binder, primarily due to phenyl group adsorption on catalyst surfaces, which reduces oxygen reduction reaction activity and impedes oxygen transport. Additional performance degradation arises from membrane-electrode interfacial incompatibility and insufficient ionomer hydrophobicity. By addressing ionomer adsorption and improving interfacial contact, an sDAPP-based cathode achieved a current density of 1.57 A cm −2 at 0.6 V under fully humidified H 2 /air conditions at 80 °C and 150 kPa abs . These results offer key insights for advancing high-performance, PFAS-free fuel cell technologies.

08 HYDROGEN↗
DOE OSTI2020

Direct Measurement of Crossover and Interfacial Resistance of Ion-Exchange Membranes in All-Vanadium Redox Flow Batteries

Among various components commonly used in redox flow batteries (RFBs), the separator plays a significant role, influencing resistance to current as well as capacity decay via unintended crossover. It is well-established that the ohmic overpotential is dominated by the membrane and interfacial resistance in most aqueous RFBs. The ultimate goal of engineering membranes is to improve the ionic conductivity while keeping crossover at a minimum. One of the major issues yet to be addressed is the contribution of interfacial phenomena in the influence of ionic and water transport through the membrane. In this work, we have utilized a novel experimental system capable of measuring the ionic crossover in real-time to quantify the permeability of ionic species. Specifically, we have focused on quantifying the contributions from the interfacial resistance to ionic crossover. The trade-off between the mass and ionic transport impedance caused by the interface of the membranes has been addressed. The MacMullin number has been quantified for a series of electrolyte configurations and a correlation between the ionic conductivity of the contacting electrolyte and the Nafion® membrane has been established. The performance of individual ion-exchange membranes along with a stack of various separators have been explored. We have found that utilizing a stack of membranes is significantly beneficial in reducing the electroactive species crossover in redox flow batteries compared to a single membrane of the same fold thickness. For example, we have demonstrated that the utilization of five layers of Nafion ® 211 membrane reduces the crossover by 37% while only increasing the area-specific resistance (ASR) by 15% compared to a single layer Nafion ® 115 membrane. Therefore, the influence of interfacial impedance in reducing the vanadium ion crossover is substantially higher compared to a corresponding increase in ASR, indicating that mass and ohmic interfacial resistances are dissimilar. We have expanded our analysis to a combination of commercially available ion-exchange membranes and provided a design chart for membrane selection based on the application of interest (short duration/high-performance vs. long-term durability). The results of this study provide a deeper insight into the optimization of all-vanadium redox flow batteries (VRFBs).

UV/Vis spectroscopy↗