Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cleaning Frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Plasma cleaning device

High vacuum cleaning of contaminated surfaces such as hydrocarbon containment films can be accomplished by a plasma cleaning device which includes a plasma discharge housing to permit generation of a plasma in an environment having a higher pressure than the surface which is to be cleaned. A ground electrode and a radio frequency electrode partially surround a quartz plasma tube, for the introduction of an ionizable gas. These electrodes ionize the gas and help generate the plasma. This plasma flows through a non-constrictive aperture, through the plasma discharge housing and then on to the contaminated surface.

Shannon, R. L.↗
DOE OSTI2022

Investigation of Ni catalyst activation during plasma-assisted methane oxidation

Atmospheric pressure plasma has shown promise in improving thermally activated catalytic reactions through a process termed plasma-catalysis synergy. In this work, we investigated atmospheric pressure plasma jet (APPJ)-assisted CH 4 oxidation over a Ni/SiO 2 .Al 2 O 3 catalyst. Downstream gas-phase products from CH 4 conversion were quantified by Fourier transform infrared spectroscopy. The catalyst near-surface region was characterized by in-situ diffuse reflectance infrared Fourier transform spectroscopy. The catalyst was observed to be activated at elevated temperature (500 °C) if it was exposed to the APPJ operated at large plasma power. 'Catalyst activation' signifies that the purely thermal conversion of CH 4 using catalysts which had been pre-exposed to plasma became more intense and produced consistently CO product, even if the plasma was extinguished. Without the application of the APPJ to the Ni catalyst surface this was not observed at 500 °C. The study of different exposure conditions of the activated catalyst indicates that the reduction of the catalyst by the APPJ is likely the cause of the catalyst activation. We also observed a systematic shift of the vibrational frequency of adsorbed CO on Ni catalyst when plasma operating conditions and catalyst temperatures were varied and discussed possible explanations for the observed changes. Furthermore, this work provides insights into the plasma-catalyst interaction, especially catalyst modification in the plasma catalysis process, and potentially demonstrates the possibility of utilizing the surface CO as a local probe to understand the plasma-catalyst interaction and shed light on the complexity of plasma catalysis.

methane oxidation↗
NASA NTRS1995

(abstract) Electromagnetic Compatability Program to Accommodate a Spacecraft Magnetic Search Coil Experiment

A search coil is a very sensitive instrument that measures low frequency magnetic field radiation. In order for the search coil to achieve its objectives, an electromagnetic clean environment must be provided. On a spacecraft, there are many potential sources of low frequency magnetic field emitter. Consequently, a very stringent program is needed to control the emission from these sources. This paper describes the details of such a program.

systems electric motors enclosures shielding↗
NASA NTRS2006

Small Hot Jet Acoustic Rig Validation

The Small Hot Jet Acoustic Rig (SHJAR), located in the Aeroacoustic Propulsion Laboratory (AAPL) at the NASA Glenn Research Center in Cleveland, Ohio, was commissioned in 2001 to test jet noise reduction concepts at low technology readiness levels (TRL 1-3) and develop advanced measurement techniques. The first series of tests on the SHJAR were designed to prove its capabilities and establish the quality of the jet noise data produced. Towards this goal, a methodology was employed dividing all noise sources into three categories: background noise, jet noise, and rig noise. Background noise was directly measured. Jet noise and rig noise were separated by using the distance and velocity scaling properties of jet noise. Effectively, any noise source that did not follow these rules of jet noise was labeled as rig noise. This method led to the identification of a high frequency noise source related to the Reynolds number. Experiments using boundary layer treatment and hot wire probes documented this noise source and its removal, allowing clean testing of low Reynolds number jets. Other tests performed characterized the amplitude and frequency of the valve noise, confirmed the location of the acoustic far field, and documented the background noise levels under several conditions. Finally, a full set of baseline data was acquired. This paper contains the methodology and test results used to verify the quality of the SHJAR rig.

Brown, Cliff↗
DOE OSTI2025

Assembling the SSR2 Cavities String for PIP-II

Characterization of the interaction between airflow and a superconducting radio frequency cavity for particle accelerators in an ultra-clean environment

Tamburrino, Alessandro [Pisa U.]↗
DOE OSTI2023

Numerical investigation of gas-filled multipass cells in the enhanced dispersion regime for clean spectral broadening and pulse compression

We show via numerical simulations that the regime of enhanced frequency chirp can be achieved in gas-filled multipass cells. Our results demonstrate that there exists a region of pulse and cell parameters for which a broad and flat spectrum with a smooth parabolic-like phase can be generated. This spectrum is compatible with clean ultrashort pulses, whose secondary structures are always below the 0.5% of its peak intensity such that the energy ratio (the energy contained within the main peak of the pulse) is above 98%. This regime makes multipass cell post-compression one of the most versatile schemes to sculpt a clean intense ultrashort optical pulse.

Segundo Staels, V. W. (ORCID:0000000200056157)↗
DOE OSTI2022

High-Power and Flexible Low-Frequency AC Transmission for Renewable Integration

This project develops a steady-state, dynamic, and production cost models of a multi-terminal, high-power, flexible low-frequency ac (LF-HVac) transmission system with grid-forming converters. Through both numerical analysis and EMTP simulation, the project goal is to demonstrate the feasibility of such an innovative and transformative LF-HVac system to support bulk integration of large-scale, cheap, and steady renewable resources from remote locations such as offshore wind farms to meet recent clean energy goals from DOE. The proposed adoption of low-frequency ac transmission aims to improve power transfer capability for remote large-scale renewable integration. In addition, the control for power electronics converters provides grid-support functions to improve the flexibility and resilience the existing 60-Hz HVac system. Future projects on this topic can be supported by both Energy Efficiency and Renewable Energy (DOEEE) and Office of Electricity Delivery & Energy Reliability (DOEOE) offices.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Molybdenum Contacts to MoS 2 Field‐Effect Transistors: Schottky Barrier Extraction, Electrical Transport, and Low‐Frequency Noise

MoS 2 has great interest for nanoscale electronic devices, including transistors and sensors. Defect‐free structure, clean interface with the gate dielectric, and metals with suitable metal–semiconductor junctions are key for reliable devices. Molybdenum is shown as an excellent electrode for MoS 2 field‐effect transistors (FETs), but the correlation among device current, field‐effect mobility, and the low‐frequency noise (LFN) with number of atomic layers is not studied. Furthermore, the impact of Mo/MoS 2 Schottky barrier on electronic injection and scattering in the device needs to be understood. Herein, by studying the FETs with channels of different numbers of atomic‐layer thicknesses, it is shown that a molybdenum metal contact to MoS 2 provides reliable current injection with low Schottky barrier height, low contact resistance, low electron–phonon scattering, and negligible impurity scattering. The mobility and LFN are optimal at a channel thickness of ≈12 atomic layers, which is consistent with the “mobility maximum window” in MoS 2 transistors with prior studies using other contact metals.

Kwon, Jiseok↗
NASA NTRS1997

Wavelet Analyses of F/A-18 Aeroelastic and Aeroservoelastic Flight Test Data

Time-frequency signal representations combined with subspace identification methods were used to analyze aeroelastic flight data from the F/A-18 Systems Research Aircraft (SRA) and aeroservoelastic data from the F/A-18 High Alpha Research Vehicle (HARV). The F/A-18 SRA data were produced from a wingtip excitation system that generated linear frequency chirps and logarithmic sweeps. HARV data were acquired from digital Schroeder-phased and sinc pulse excitation signals to actuator commands. Nondilated continuous Morlet wavelets implemented as a filter bank were chosen for the time-frequency analysis to eliminate phase distortion as it occurs with sliding window discrete Fourier transform techniques. Wavelet coefficients were filtered to reduce effects of noise and nonlinear distortions identically in all inputs and outputs. Cleaned reconstructed time domain signals were used to compute improved transfer functions. Time and frequency domain subspace identification methods were applied to enhanced reconstructed time domain data and improved transfer functions, respectively. Time domain subspace performed poorly, even with the enhanced data, compared with frequency domain techniques. A frequency domain subspace method is shown to produce better results with the data processed using the Morlet time-frequency technique.

Martin J Brenner↗
NASA NTRS1973

Personal hygienic concerns in long term space flight

Data from numerous experiments and hardware inventories were scanned for Skylab personal hygiene use. A computer program was formulated for predicting the degree of man's involvement with personal hygiene needs. A tabulation was kept for such events as water intake, frequency of urination and defecation, accidents or events requiring clean-up, methods of clean-up, microbiological environment and shower water contamination.

Source record↗
DOE OSTI2022

Molecular beam homoepitaxy of N-polar AlN: Enabling role of aluminum-assisted surface cleaning

N-polar aluminum nitride (AlN) is an important building block for next-generation high-power radio frequency electronics. We report successful homoepitaxial growth of N-polar AlN by molecular beam epitaxy (MBE) on large-area, cost-effective N-polar AlN templates. Direct growth without any in situ surface cleaning leads to films with inverted Al polarity. It is found that Al-assisted cleaning before growth enables the epitaxial film to maintain N-polarity. The grown N-polar AlN epilayer with its smooth, pit-free surface duplicates the structural quality of the substrate, as evidenced by a clean and smooth growth interface with no noticeable extended defects generation. Near band-edge photoluminescence peaks are observed at room temperature on samples with MBE-grown layers but not on the bare AlN templates, implying the suppression of nonradiative recombination centers in the epitaxial N-polar AlN.

42 ENGINEERING↗
NASA NTRS2007

Rarefying Spectra of Whispering-Gallery-Mode Resonators

A method of cleaning the mode spectra of whispering-gallery-mode (WGM) optical resonators has been devised to make such resonators more suitable for use as narrow-band optical filters. The method applies, more specifically, to millimeter- sized whispering-gallery-mode optical resonators that are made of crystalline electro-optical materials and have ultrahigh values of the resonance quality factor (Q). The mode spectrum of such a resonator is typically dense, consisting of closely spaced families of modes; as such, the spectrum is not well suited for narrow-band filtering, in which there is a need for strong rejection of side modes. Cleaning as used here signifies rarefying the spectrum so that what remains consists mostly of a single desired family of modes or, at worst, a few mode families that are more widely spaced in frequency than are the mode families in the original, non-rarefied spectrum. The spectrum-cleaning method exploits the fact that various WGM mode families occupy various positions near the equator at the rim of a resonator disk. In this method, a damper in the form of a prism or other polished piece of material having an index of refraction greater than that of the resonator material is placed in contact with the rim of the resonator at such a position that the Qs of most or all of the undesired mode families are greatly reduced while the Q of the desired mode family is reduced by only a tolerably small amount. In an alternative method that has been considered, the mode spectrum would be cleaned through special design of the shape of the rim, but fabrication of the rim in a special shape is a complicated task. The advantage of the present method, relative to the alternative method, is that special shaping of the rim is not necessary and the damping prism can be emplaced after the resonator has been fabricated.

Savchenkov, Anatoliy↗
DOE OSTI2022

Gifts from anomalies: Exact results for Landau phase transitions in metals

Non-Fermi liquid phenomena arise naturally near critical points of Landau ordering transitions in metallic systems, where strong fluctuations of a bosonic order parameter destroy coherent quasiparticles. Despite progress in developing controlled perturbative techniques, much of the low energy physics of such metallic quantum critical points remains poorly understood. We demonstrate that exact, non-perburbative results can be obtained for both optical transport and static susceptibilities in “Hertz-Millis” theories of Fermi surfaces coupled to critical bosons. Such models possess a large emergent symmetry and anomaly structure, which we leverage to fix these quantities. In particular, we show that in the infrared limit, the boson self energy at zero wave vector, \mathbf{q}=0 𝐪 = 0 , is a constant independent of frequency, and the real part of the optical conductivity, \sigma(\omega) σ ( ω ) , is purely a delta function Drude peak with no other corrections. Therefore, further frequency dependence in the boson self energy or optical conductivity can only come from irrelevant operators in a clean system. Exact relations between Fermi liquid parameters as the critical point is approached from the disordered phase are also obtained. The absence of a universal, power law frequency dependence in the boson self energy contrasts with previous perturbative calculations, and we explain the origin of this difference.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Ameliorating Global Challenges: Globalization, Geopolitics, Basic & Applied Research, and Research Security

We are confronted with a myriad of global challenges, from extreme weather events, occurring at higher frequencies than at any point in history, to pollution, food insecurity, clean water shortages, and fundamentally limited natural resources and materials. The largest number of people inhabit our planet today and enjoy the highest standard of living - though not equally distributed across the world - compared to any prior moment in history. To sustain this quality of life, we are largely reliant on fossil fuel sources, which are responsible for more greenhouse gas emissions by weight each day than the collective weight of all humans that inhabit the planet. Ameliorating these global challenges will require elements of solutions that include advances in basic and applied research, innovative global engineering, materials discovery, new technologies, manufacturing at scale, resilient and adaptable infrastructure, carbon-free energy sources and storage technologies, and new supply chain networks and markets. Success will require constructive collaborative efforts between researchers in countries located in every continent of this planet. For any of these goals to be realized in a timely fashion, geopolitical leaders must become better educated about this existential challenge and incentivized to act.

applied research↗
DOE OSTI2021

Magnetron R&D for high efficiency CW RF sources for industrial accelerators

The scheme of using high-efficiency magnetrons to drive radiofrequency accelerators has been demonstrated at 2450 MHz in CW mode *. Magnetron test stands at JLab and GA have been set up to further test the noise figure and the locking speed of the injection phase-lock method. For higher power applications, power combining experiments using a TM010 cavity-type combiner and a magic tee for the binary combiner while using a single clean injection signal has been carried out at 2450 MHz. The frequency pulling effect between the magnetron and a low-Q cavity has been shown to enhance the frequency locking bandwidth compared to the injection phase-lock alone. The principle has been studied by the equivalent circuit simulation, analytical model, and finally confirmed experimentally on the magnetrons. Due to the pandemic delay in 2020, the equivalent high power tests using a 75kW, 915MHz industrial magnetron will be done in 2021 and will be reported in a future paper.

Wang, H.↗
DOE OSTI2024

High pressure rinse simulations for PIP-II SRF cavities

The implementation of High Pressure Rinse (HPR) not only ensures thorough cleaning of the inner high purity niobium surface of Superconducting Radio Frequency (SRF) cavities but also unlocks their full potential for achieving peak performance. By effectively removing contaminants and impurities, HPR sets the stage for enhanced superconducting properties, improved energy efficiency, and superior operational stability. A simulation tool has been developed, facilitating the accurate prediction of both the quality and effectiveness of the rinsing process before its execution in the cleanroom. This tool, the focus of this paper, stands as a pivotal advancement in optimizing Superconducting Radio Frequency (SRF) cavity preparation. Furthermore, our paper will also present correlations with cavity cold testing results, demonstrating the practical applicability and reliability of the simulation predictions in real-world scenarios.

43 PARTICLE ACCELERATORS↗
NASA NTRS1974

Process to restore obliterated serial numbers on metal surfaces

Metal smeared into grooves of serial numbers by grinding or filing can be cleaned out by process called cavitation. Ultrasonic vibrator generates very high frequency vibrations in water which create millions of microscopic bubbles. Cavitation bubbles impact metal surface at thousands of pounds per square inch pressure. Metal particles filling grooves are broken away.

Young, S. G.↗
NASA NTRS2006

Stability Enhancement of Polymeric Sensing Films Using Fillers

Experiments have shown the stability enhancement of polymeric sensing films on mixing the polymer with colloidal filler particles (submicron-sized) of carbon black, silver, titanium dioxide, and fumed silicon dioxide. The polymer films are candidates for potential use as sensing media in micro/nano chemical sensor devices. The need for stability enhancement of polymer sensing films arises because such films have been found to exhibit unpredictable changes in sensing activity over time, which could result in a possible failure of the sensor device. The changes in the physical properties of a polymer sensing film caused by the sorption of a target molecule can be measured by any of several established transduction techniques: electrochemical, optical, calorimetric, or piezoelectric, for example. The transduction technique used in the current polymer stability experiments is based on piezoelectric principles using a quartz-crystal microbalance (QCM). The surface of the QCM is coated with the polymer, and the mass uptake by the polymer film causes a change in the oscillating frequency of the quartz crystal. The polymer used for the current study is ethyl cellulose. The polymer/ polymer composite solutions were prepared in 1,3 dioxolane solvent. The filler concentration was fixed at 10 weight percent for the composites. The polymer or polymer composite solutions were cast on the quartz crystal having a fundamental frequency of about 6 MHz. The coated crystal was subjected to a multistage drying process to remove all measurable traces of the solvent. In each experiment, the frequency of oscillation was measured while the QCM was exposed to clean, dry, flowing air for about 30 minutes, then to air containing a known concentration of isopropanol for about 30 minutes, then again to clean dry air for about 30 minutes, and so forth. This cycle of measurements for varying isopropanol concentrations was repeated at intervals for several months. The figure depicts some of the sensing film stability results for ethyl cellulose polymer, ethyl cellulose-carbon black, and ethyl cellulose-silicon dioxide composite systems. An ethyl cellulose film exhibited a marked decline in response in the first few months of study and settled to a steady average response after about four months. However, response varied widely around the average response for ethyl cellulose film. In contrast, ethyl cellulose- carbon black and ethyl cellulose-silicon dioxide composites also declined in the early months, but showed more repeatable sensing film activity after the initial decline. Similar trends were observed in experiments for ethyl cellulose-titanium dioxide and ethyl cellulose-silver composites.

Lin, Brian↗