Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fissionable Material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Measurement of Mass-Independent Perturbations of Cadmium in Nuclear Debris Samples

The isotopic composition of cadmium in nuclear debris was measured by multi-collector inductively coupled plasma-mass spectrometry (MC-ICP-MS). Mass-independent perturbations due to fission product decay on the isotopes of Cd were observed. Relative fission yields for masses 111, 112, 114 and 116 were determined in each sample of nuclear debris and compared with reported values found in irradiated plutonium and uranium fuels. Mass spectrometry measurements of the valley fission product endpoints are extremely challenging due to the low cumulative fission yields and small amounts of each isotope that are produced. To overcome these challenges, a new purification method for Cd was developed and validated by examination of a number of geological reference materials.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRSDate not supplied

Powering Moon, Mars, and Beyond

A panel discussion on Fission Surface Power program outlining the progress made at NASA and national labs over time and the path forward. This panel will outline the technical achievements made for materials, power conversion, experiments and deployment. Panelists will cover a broad range of topics during their presentation and will be followed by an audience based Q&A afterwards.

fission surface power↗
DOE OSTI2020

STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications

Oak Ridge National Laboratory is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys for accident tolerant fuel (ATF) cladding. This report presents the characterization of two new ODS FeCrAl tubes by using powder commercially mechanically alloyed by Zoz GmbH, which underwent high-precision tube rolling with two different annealing schedules. This work shows that the ODS FeCrAl tube without recrystallization exhibits consistent mechanical behavior in comparison with a previously produced tube. The second tube, which underwent a full recrystallization step before the final tube rolling step, showed some circumferential cracking and exhibited limited ductility in the axial tube tensile tests. Based on current and prior work on the ODS FeCrAl alloy system, this report compares the current state of the scientific literature on the alloy class with that of wrought FeCrAl without oxide additions. Then, this report makes recommendations for future research directions that should be undertaken to increase the technology readiness level for ODS FeCrAl as a viable ATF candidate material. This report has been submitted as fulfillment of milestone M3FT-20OR020202064 titled, “STEP Report on Advanced ODS FeCrAl Alloys for Fission Applications” for the US Department of Energy Office of Nuclear Energy’s Advanced Fuel Campaign of the Fuel Cycle R&D program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Retention of radionuclides in sol–gel surrogate nuclear explosive debris

Sol–gel vitrification can be used to rapidly produce solid, vitreous materials to support nuclear forensics research. Here, this work investigates three sol–gel synthetic approaches’ ability to retain fission products within the glass as a function of drying temperature. Eight of the ten fission products studied were quantitatively retained (less than 5% losses) at temperatures up to 600 °C for glasses prepared using an acidic catalyst and at temperatures up to 300 °C for glasses prepared using a basic catalyst. Both systems show partial loss of ruthenium and complete loss of iodine at temperatures above 300 and 100 °C, respectively.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Myths of nuclear graphite in World War II, with original translations

We re-examine a common narrative that experimental errors by Walther Bothe in 1941 led Germany to abandon graphite as a reactor moderator during World War II. Using document-based nuclear archaeology, we first show that both American and German scientists used an incorrect carbon scattering cross section, thereby undermining the accuracy of all wartime data, including their conclusions on carbon’s absorption. Moreover, we argue that the availability of exceptionally pure petroleum coke in the United States, rather than any academic breakthrough, decisively enabled their production of nuclear-grade graphite. In contrast, Bothe’s Siemens electrographite had more boron contamination than any graphites considered in Fermi’s experiments, rendering it genuinely impractical as a moderator. By reframing the decision to eschew graphite as a deliberate decision rather than a mere experimental oversight, we believe the German decision was a rational consequence of material constraints and wartime priorities.

42 ENGINEERING↗
DOE OSTI2020

AWCC Simulations

Neutron well counters provide a means to measure fissile mass by detecting coincident neutrons, which is a unique signature to fission. For coincidence counting, mass is determined using a calibration curve established with items that have the same material characteristics. Multiplicity analysis solves the point model equations for mass using known detector parameters. In both cases, mass measurements may exhibit a bias due to item characteristics and should be corrected for. Experiments can be done to estimate bias and material effects, but they require having both the well counter and the material well defined. In pursuit of estimating measurement bias and uncertainty in a High Efficiency Neutron Counter (HENC), an MCNP simulation was matched to measurements performed with an Active Well Coincidence Counter (AWCC) to de ne a neutron source term. The neutron source term will be used to predict measurement performance of similar material types in a HENC.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Irradiation Testing of Ultrasonic Transducers

Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of numerous parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of single, small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of existing knowledge of ultrasonic transducer material survivability under irradiation conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate promising magnetostrictive and piezoelectric transducer performance in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 1021 n/cm2 (E> 0.1 MeV). This test will be an instrumented lead test; and real-time transducer performance data will be collected along with temperature and neutron and gamma flux data. By characterizing magnetostrictive and piezoelectric transducer survivability during irradiation, test results will enable the development of novel radiation tolerant ultrasonic sensors for use in Material and Test Reactors (MTRs). The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers

Daw, J.↗
NASA NTRS1976

Formation chronology for C2 meteorites

The times at which phyllosilicate matrix and euhedral olivines became associated have been determined for five C2 meteorites. The ages, calculated from fission track densities on crystal surfaces, are based on an initial Pu-244/U-238 ratio in the matrix material of 0.0154 at 4.6 b.y., and range from 4.22 b.y. for Nogoya to 4.42 b.y. for Murray. Unless the initial Pu-244/U-238 ratio was less than 0.004, the meteorites cannot have existed in their present form for 4.6 billion years. The measured ages place limits on the time when pre-compaction effects such as micrometeorite craters and solar flare tracks were produced, and they may approximately date the formation of the olivine crystals themselves.

Macdougall, J. D.↗
DOE OSTI2020

AGR-5/6/7 Irradiation Summary as of the End of Cycle 167A

Overall, the first three cycles of irradiation proceeded as planned Items of note: Failure rate of thermocouples was higher than expected Downstream needle valves were throttled resulting in part of the exhaust flow being diverted prior to reaching the fission product monitors (this was corrected near the end of cycle 164B). This was more of annoyance than anything and did not prevent proper analysis of fission product data. No evidence of failures on fission product monitoring system.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

AGR-5/6/7 Post-Irradiation Examination Plan

This plan describes the PIE activities to be carried out on AGR-5/6/7 fuel and the non-fuel components of the AGR-5/6/7 irradiation test train. PIE of AGR-5/6/7 fuel and test train components will provide data on fuel performance over a range of irradiation conditions (e.g., burnup, neutron fluence, and temperature), test fuel under postulated accident conditions, and support development of fuel performance and fission product transport models. Examination of the non-fuel test train components will give information on TRISO fuel and compact performance and information on releases of radioactive fission products from the fuel compacts. PIE of the fuel compacts is used for many purposes including, but not limited to: updating the irradiation thermal calculations, measuring burnup, determining retention/release of fission products from the compacts and the TRISO particles, determining TRISO layer failure rates, determining fuel performance at elevated accident temperatures, determining fuel performance under oxidizing atmospheres, determining the distribution of fission products within the compact and fuel particles, and observing compact and particle morphology to explain mechanisms of TRISO layer failure and/or fission product release/retention.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2001

Fusion for Space Propulsion and Plasma Liner Driven MTF

The need for fusion propulsion for interplanetary flights is discussed. For a propulsion system, there are three important system attributes: (1) The absolute amount of energy available, (2) the propellant exhaust velocity, and (3) the jet power per unit mass of the propulsion system (specific power). For human exploration and development of the solar system, propellant exhaust velocity in excess of 100 km/s and specific power in excess of 10 kW/kg are required. Chemical combustion cannot meet the requirement in propellant exhaust velocity. Nuclear fission processes typically result in producing energy in the form of heat that needs to be manipulated at temperatures limited by materials to about 2,800 K. Using the energy to heat a low atomic weight propellant cannot overcome the problem. Alternatively the energy can be converted into electricity which is then used to accelerate particles to high exhaust velocity. The necessary power conversion and conditioning equipment, however, increases the mass of the propulsion system for the same jet power by more than two orders of magnitude over chemical system, thus greatly limits the thrust-to-weight ratio attainable. If fusion can be developed, fusion appears to have the best of all worlds in terms of propulsion - it can provide the absolute amount, the propellant exhaust velocity, and the high specific jet power. An intermediate step towards pure fusion propulsion is a bimodal system in which a fission reactor is used to provide some of the energy to drive a fusion propulsion unit. The technical issues related to fusion for space propulsion are discussed. There are similarities as well as differences at the system level between applying fusion to propulsion and to terrestrial electrical power generation. The differences potentially provide a wider window of opportunities for applying fusion to propulsion. For example, pulsed approaches to fusion may be attractive for the propulsion application. This is particularly so in the light of significant development of the enabling pulsed power component technologies that have occurred in the last two decades because of defense and other energy requirements. The extreme states of matter required to produce fusion reactions may be more readily realizable in the pulsed states with less system mass than in steady states. Significant saving in system mass may result in pulsed fusion systems using plasmas in the appropriate density regimes. Magnetized target fusion, which attempts to combine the favorable attributes of magnetic confinement and inertial compression-containment into one single integrated fusion scheme, appears to have benefits that are worth exploring for propulsion application.

Thio, Y.C. Francis↗
DOE OSTI2025

Experimental confirmation of first-principles thermal conductivity in Zirconium-doped ThO 2

The degradation of thermal conductivity in advanced nuclear fuels due to the accumulation of fission products and irradiation-induced defects is inevitable, and must be considered as part of safety and efficiency analyses of nuclear reactors. Here, this study examines the thermal conductivity of a zirconium-doped ThO 2 crystal, synthesized via the hydrothermal method using a spatial domain thermoreflectance technique. Zirconium is one of the soluble fission products in oxide fuels that can effectively scatter heat-carrying phonons in the crystalline lattice of fuel. Thus, thermal property measurements of zirconium-doped ThO 2 single crystals provide insights into the effects of substitutional zirconium doping, isolated from extrinsic factors such as grain boundary scattering. The experimental results are compared with first-principles calculations of the lattice thermal conductivity of ThO 2 , employing an iterative solution of the Peierls-Boltzmann transport equation. Additionally, the non-perturbative Green's function methodology is utilized to compute phonon-point defect scattering rates, accounting for local distortions around point defects, including mass difference changes, interatomic force constants, and structural relaxation. The congruence between the predicted results from first-principles calculations and the measured temperature-dependent thermal conductivity validates the computational methodology. Furthermore, the methodologies employed in this study enable systematic investigations of thermal conductivity reduction by fission products, potentially leading to the development of more accurate fuel performance codes.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Deconsolidation and Leach Burn Leach of Seven As Irradiated AGR 5/6/7 TRISO Fuel Compacts from Capsules 2, 3, 4, and 5

Seven as-irradiated Advanced Gas Reactor (AGR) 5/6/7 compacts underwent destructive post-irradiation examination via deconsolidation-leach-burn leach at Idaho National Laboratory (INL). The selection of the compacts extended the upper and lower limits of time-average volume-average (TAVA) temperature for compacts that had gone through deconsolidation-leach-burn leach so far. The measured inventories of fission products and actinides in the compact matrix and outer pyrolytic carbon were reported. Results indicated unexpectedly higher rates of fuel kernel leaching compared to compacts from AGR-1 and AGR-2. These failure rates were attributed to damage during post-irradiation sample handling, rather than irradiation itself. AGR-5/6/7 compacts have little or no matrix coverage for some particles at the top and bottom ends of cylindrical fuel compacts, making them more fragile. Sixty particles were randomly sampled from each compact, and the gamma results were reported. Three SiC shells from were identified, one of which showed signs of chemical attack in the high-irradiation temperature compact.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this presentation are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Multi-element isotopic analysis of hot particles from Chornobyl

Microscopic fuel fragments, so-called “hot particles”, were released during the 1986 accident at the Chornobyl nuclear powerplant and continue to contaminate the exclusion zone in northern Ukraine. Isotopic analysis can provide vital information about sample origin, history and contamination of the environment, though it has been underutilized due to the destructive nature of most mass spectrometric techniques, and inability to remove isobaric interference. Recent developments have diversified the range of elements that can be investigated through resonance ionization mass spectrometry (RIMS), notably in the fission products. The purpose of this study is to demonstrate the application of multi-element analysis on hot particles as relates to their burnup, particle formation in the accident, and weathering. The particles were analysed with two RIMS instruments: resonant-laser secondary neutral mass spectrometry (rL-SNMS) at the Institute for Radiation Protection and Radioecology (IRS) in Hannover, Germany, and laser ionization of neutrals (LION) at Lawrence Livermore National Laboratory (LLNL) in Livermore, USA. Comparable results across instruments show a range of burnup dependent isotope ratios for U and Pu and Cs, characteristic of RBMK-type reactors. Results for Rb, Ba and Sr show the influence of the environment, retention of Cs in the particles and time passed since fuel discharge.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Chemical Modeling of the Capture of Radioiodine Species

Iodine is a common fission product resulting from the transmutation of uranium fuel in nuclear power reactors. The short-lived radioactive isotope, 131 I, with a half-life of around eight days, would be a particular health concern if released into the environment. Capture materials, such as activated carbon, are used routinely in nuclear power plants and medical isotope production facilities to remove this hazard during normal operations to reduce emissions to acceptable levels. Iodine, unlike other common fission products such as noble gases, is challenging because of the wide range of molecular forms and oxidation states (from +VII in IF 7 to -I in iodide) that it displays, which can interconvert both in the gas phase and in the solution phase for example. The work in this project is focused on three computational tasks. In the first, we consider the binding of iodine-containing molecules of varying oxidation states to the major component of activated carbon – pristine graphene-like sheets. The second task focused on molecular binding and possible chemical transformations resulting from the reaction of molecular iodine with chemical functional groups on the edge of the graphene sheets or surface defects in the sheet itself. The final task was associated with radiolytic breakdown of 131 I to 131 Xe in iodine containing molecules and investigated the resulting molecular fragmentation process both in the gas phase and on the graphene-like surface. For each of the tasks, the intent was to learn about the thermodynamics and kinetics of the chemical transformations and use the calculations to provide parameters for input into kinetic models describing these processes for interpretation of experimental data in future work.

07 ISOTOPE AND RADIATION SOURCES↗