Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DAMPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Steady-state unbalance response of a three-disk flexible rotor on flexible, damped supports

Experimental data are presented for the unbalance response of a flexible, ball bearing supported rotor to speeds above the third lateral bending critical. Values of squeeze film damping coefficients obtained from measured data are compared to theoretical values obtained from short bearing approximation over a frequency range from 5000 to 31 000 cycles/min. Experimental response for an undamped rotor is compared to that of one having oil squeeze film dampers at the bearings. Unbalance applied varied from 0.62 to 15.1 gm-cm.

Cunningham, R. E.↗
NASA NTRS1977

Utilization of separate surface control systems on general aviation aircraft

The application of separate surface control systems to general aviation aircraft is discussed. Block diagrams of a conventional control system with autopilot tie-in and of a separate surface control system are presented, and the advantages and disadvantages of the two systems are compared. Theoretical descriptions of pilot-in-the-loop operation and operation in the autopilot mode are presented. The application of separate surface stability augmentation in yaw dampers, wing levelers, and static longitudinal stability augmentation is examined. The state-of-the-art of separate control surface technology is summarized.

Roskam, J.↗
NASA NTRS1979

Stable hydraulic pressure regulator

Neither sensing line restrictors nor frictional dampers are required for stability. Analysis presents method by which stability margin, response, and droop magnitude can be incorporated during design of direct-acting hydraulic pressure regulators.

Gold, H.↗
NASA NTRS1977

Influence of oil-squeeze-film damping on steady-state response of flexible rotor operating to supercritical speeds

Experimental data were obtained for the unbalance response of a flexible rotor to speeds above the third lateral bending critical. Squeeze-film damping coefficients calculated from measured data showed good agreement with short-journal-bearing approximations over a frequency range from 5000 to 31,000 cmp. Response of a rotor to varying amounts of unbalance was investigated. A very lightly damped rotor was compared with one where oil-squeeze dampers were applied.

Cunningham, R. E.↗
NASA NTRS1977

Prototype solar heating and hot water systems

Alternative approaches to solar heating and hot water system configurations were studied, parametrizing the number and location of the dampers, the number and location of the fans, the interface locations with the furnace, the size and type of subsystems, and operating modes. A two-pass air-heating collector was selected based on efficiency and ease of installation. Also, an energy transport module was designed to compactly contain all the mechanical and electrical control components. System performance calculations were carried out over a heating season for the tentative site location at Tunkhnana, Pa. Results illustrate the effect of collector size, storage capacity, and use of a reflector. Factors which affected system performance include site location, insulative quality of the house, and of the system components. A preliminary system performance specification is given.

Source record↗
NASA NTRS1978

Performance with and without inlet radial distortion of a transonic fan stage designed for reduced loading in the tip region

A transonic compressor stage designed for a reduced loading in the tip region of the rotor blades was tested with and without inlet radial distortion. The rotor was 50 cm in diameter and designed for an operating tip speed of 420 m/sec. Although the rotor blade loading in the tip region was reduced to provide additional operating range, analysis of the data indicates that the flow around the damper appears to be critical and limited the stable operating range of this stage. For all levels of tip and hub radial distortion, there was a large reduction in the rotor stall margin.

Schmidt, J. F.↗
NASA NTRS1978

Design and performance of a 427-meter-per-second-tip-speed two-stage fan having a 2.40 pressure ratio

The aerodynamic design and the overall and blade-element performances are presented of a 427-meter-per-second-tip-speed two-stage fan designed with axially spaced blade rows to reduce noise transmitted upstream of the fan. At design speed the highest recorded adiabatic efficiency was 0.796 at a pressure of 2.30. Peak efficiency was not established at design speed because of a damper failure which terminated testing prematurely. The overall efficiencies, at 60 and 80 percent of design speed, peaked at approximately 0.83.

Cunnan, W. S.↗
NASA NTRS1977

Steady-state unbalance response of a three-disk flexible rotor on flexible, damped supports

Experimental data are presented for the unbalance response of a flexible, ball bearing supported rotor to speeds above the third lateral bending critical. Values of squeeze film damping coefficients obtained from measured data are compared to theoretical values obtained from short bearing approximation over a frequency range from 5000 to 31,000 cycles/min. Experimental response for an undamped rotor is compared to that of one having oil squeeze film dampers at the bearings. Unbalances applied varied from 0.62 to 15.1 gm-cm.

Cunningham, R. E.↗
NASA NTRS1978

Theory of the control of structures by low authority controllers

The novel idea presented is based on the observation that if a structure is controlled by distributed systems of sensors and actuators with limited authority, i.e., if the controller is allowed to modify only moderately the natural modes and frequencies of the structure, then it should be possible to apply root perturbation techniques to predict analytically the behavior of the total system. Attention is given to the root perturbation formula first derived by Jacobi for infinitesimal perturbations which neglect the induced eigenvector perturbation, a more general form of Jacobi's formula, first-order structural equations and modal state vectors, state-space equations for damper-augmented structures, and modal damping prediction formulas.

Aubrun, J. N.↗
NASA NTRS1980

Controlling subsynchronous whirl in turbopumps

Active fluidic dampers are proposed for controlling turbopump-shaft whirl. Study indicates that linear variable-bleed detector and linear bistable amplifier are effective in supplying sizable controlled damping forces. Linear bistable device was considered as simplest and most adequate.

Black, M. D.↗
NASA NTRS1978

Helicopter internal noise control: Three case histories

Case histories are described in which measurable improvements in the cabin noise environments of the Bell 214B, 206B, and 222 were realized. These case histories trace the noise control efforts followed in each vehicle. Among the design approaches considered, the addition of a fluid pulsation damper in a hydraulic system and the installation of elastomeric engine mounts are highlighted. It is concluded that substantial weight savings result when the major interior noise sources are controlled by design, both in altering the noise producing mechanism and interrupting the sound transmission paths.

Edwards, B. D.↗
NASA NTRS1978

System design package for SIMS prototype system 4, solar heating and domestic hot water

The system consisted of a modular designed prepackaged solar unit, containing solar collectors, a rock storage container, blowers, dampers, ducting, air-to-water heat exchanger, DHW preheat tank, piping, and system controls. The system was designed to be installed adjacent to a small single family dwelling. The description, performance specification, subsystem drawings, verification plan/procedure, and hazard analysis of the system were packaged for evaluation.

Source record↗
NASA NTRS1979

Flap-lag-torsion flutter analysis of a constant life rotor

The constant lift rotor (CLR) employs a control input of pitch moment to several airfoil sections which are free to pivot on a continuous spar, allowing them to change their pitch to obtain the desired lift. A flap-lag-torsion flutter analysis of a constant lift rotor blade in hover was developed. The blade model assumes rigid body flap and lead-lag motions at the root hinge and each strip undergoes an independent torsional motion. The results are presented in terms of root locus plots of complex eigenvalues as a function of thrust. The effects of several parameters (including structural damping, center of gravity and elastic axis offset from aerodynamic center, compressibility pitch-lag and pitch-flap coupling) on the blade dynamics are examined. With a suitable combination of lag damper and pitch-flap coupling, it is possible to design a constant lift rotor blade free from flutter instability.

Chopra, I.↗
NASA NTRS1979

Deployment mechanisms on Pioneer Venus probes

Deployment mechanisms were developed to position scientific instruments during probe descent into the Venus atmosphere. Each mechanism includes a provision for pyrotechnic release of the enclosure door, negator springs for positive deployment torque, and an active damper using a shunted dc motor. The deployment time requirement is under 2 seconds, and the deployment shock must be less than 100 g's. The mechanism is completely dry lubricated and constructed mainly of titanium for high strength and high temperature stability. The mechanism was qualified for descent decelerations up to 565 g's and for instrument alignment up to 940 F. The mechanism requirements, the hardware design details, the analytical simulations, and the qualification testing are described.

Townsend, W. L.↗
NASA NTRS1977

The 11th Aerospace Mechanisms Symposium

Various mechanisms in aerospace engineering were presented at this conference. Specifications, design, and use of spacecraft and missile components are discussed, such as tail assemblies, radiometers, magnetormeters, pins, reaction wheels, ball bearings, actuators, mirrors, nutation dampers, airfoils, solar arrays, etc.

Source record↗
NASA NTRS1979

INTELSAT 4 in orbit liquid slosh tests and problems in the theoretical analysis of the data

The destabilizing effect of the liquid on attitude nutation stability was determined from an extensive series of inorbit tests. The liquid slosh driving frequency ratio (rotor nutation frequency/rotor spin rate) was varied over the range of 0.58 to 0.70 for the tests by rotating the spacecraft antenna platform at different rates in inertial space. A rotor mounted accelerometer sensed the spacecraft nutation. The observed time constant for the nutation angle increase or decrease was corrected for the stabilizing contribution of the platform mounted pendulum dampers to yield the net destabilizing dedamping contribution from the liquid slosh. The in orbit tests show two unexpected maxima in the dedamping contribution at driving frequency ratios that vary with the propellant loading. The rotor nutation frequency at the maxima was about one-third of the lowest mode liquid slosh frequency given by ground test data for unspun tanks, and thus did not correspond to a simple resonance of the liquid. Ground tests with spinning systems produced the same maxima, but the phenomenon is not yet understood.

Slabinski, V. J.↗
NASA NTRS1979

Performance of two-stage fan having low-aspect-ratio first-stage rotor blading

The NASA two stage fan was tested with a low aspect ratio first stage rotor having no midspan dampers. At design speed the fan achieved an adiabatic design efficiency of 0.846, and peak efficiencies for the first stage and rotor of 0.870 and 0.906, respectively. Peak efficiency occurred very close to the stall line. In an attempt to improve stall margin, the fan was retested with circumferentially grooved casing treatment and with a series of stator blade resets. Results showed no improvement in stall margin with casing treatment but increased to 8 percent with stator blade reset.

Urasek, D. C.↗
NASA NTRS1979

Elastomer mounted rotors - An alternative for smoother running turbomachinery

This paper describes the design of elastomeric bearing supports for a rotor built to simulate the power turbine of an advanced gas turbine engine which traverses two bending critical speeds. The elastomer dampers were constructed so as to minimize rotor dynamic response at the critical speeds. Results are presented of unbalance response tests performed with two different elastomer materials. These results showed that the resonances on the elastomer-mounted rotor were well damped for both elastomer materials and showed linear response to the unbalance weights used for response testing. Additional tests were performed using solid steel supports at either end (hand-mounted), which resulted in drastically increased sensitivity and nonlinear response, and with steel supports in one end of the rotor and the elastomer at the other, which yielded results which were between the soft- and hard-mounted cases. It is concluded that elastomeric supports are a viable alternative to other methods of mounting flexible rotors, that damping was well in excess of predictions and that elastomeric supports are tolerant of small rotor misalignments.

Tecza, J. A.↗