Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solid dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 505 records · Page 28

Ultrasound-Assisted Leaching and Kinetic Study of Blended Copper Slag

This article deals with the dissolution of blended copper slag (flash and converter furnace) in hydrogen peroxide and acetic acid in the presence of ultrasound. The parameters that are effective on leaching efficiency, such as leaching temperature, leaching time, ultrasound power, acetic acid concentration, and hydrogen peroxide concentration, were investigated. The optimum leaching conditions for maximum copper dissolution (93 pct) and minimum iron dissolution (3 pct) were determined as follows: 2 M H{sub 2}O{sub 2}, 4 M CH{sub 3}COOH, 10 pct of ultrasound power, 65 °C of leaching temperature, 60 minutes of leaching time, and 1:25 of solid–liquid ratio. According to the Brunauer–Emmett–Teller (BET) analysis results on the original sample and leaching residue, the ultrasound caused formation of microcracks on the particle surface; however, the BET surface area increased and the mean adsorption pore width decreased. The apparent activation energy was found to be 55.35 kJ/mol, and the kinetics equations of the processes were established.

36 MATERIALS SCIENCE↗

Strontium isotope quantification of siderite, brine and acid mine drainage contributions to abandoned gas well discharges in the Appalachian Plateau

Unplugged abandoned oil and gas wells in the Appalachian region can serve as conduits for the movement of waters impacted by fossil fuel extraction. Strontium isotope and geochemical analysis indicate that artesian discharges of water with high total dissolved solids (TDS) from a series of gas wells in western Pennsylvania result from the infiltration of acidic, low Fe (Fe < 10 mg/L) coal mine drainage (AMD) into shallow, siderite (iron carbonate)-cemented sandstone aquifers. The acidity from the AMD promotes dissolution of the carbonate, and metal- and sulfate-contaminated waters rise to the surface through compromised abandoned gas well casings. Strontium isotope mixing models suggest that neither upward migration of oil and gas brines from Devonian reservoirs associated with the wells nor dissolution of abundant nodular siderite present in the mine spoil through which recharge water percolates contribute significantly to the artesian gas well discharges. Natural Sr isotope composition can be a sensitive tool in the characterization of complex groundwater interactions and can be used to distinguish between inputs from deep and shallow contamination sources, as well as between groundwater and mineralogically similar but stratigraphically distinct rock units. This is of particular relevance to regions such as the Appalachian Basin, where a legacy of coal, oil and gas exploration is coupled with ongoing and future natural gas drilling into deep reservoirs.

03 NATURAL GAS↗

Fate of cobalt and nickel in mackinawite during diagenetic pyrite formation

As iron sulfide mineral phases are important sedimentary sinks for naturally occurring or contaminant metals, it is important to know the fate of metals during the diagenetic transformation of primary sulfide minerals into more stable phases, such as pyrite (FeS 2 ). Furthermore, the trace metal content of pyrite has been proposed as a marine paleoredox proxy. Given the diverse low-temperature diagenetic formation pathways for pyrite, this use of pyrite requires validation. In this work, we studied nickel (Ni) and cobalt (Co) incorporation into freshly precipitated mackinawite (FeS m ), and after experimental diagenesis to pyrite (FeS 2 ) using S 0 as an oxidant at 65 °C. Metal incorporation was quantified on bulk digests using ICP-OES or ICP-AES. Bulk mineralogy was characterized with micro-X-ray diffraction (micro-XRD), documenting the transformation of mackinawite to pyrite. Epoxy grain mounts were made anoxically of mackinawite and pyrite grains. We used synchrotron-based micro-X-ray fluorescence (μXRF) to map the distribution of Co and Ni, as well as to collect multiple energy maps throughout the sulfur (S) K-edge. Iron (Fe) and S K-edge micro-X-ray absorption near edge spectroscopy (μXANES) was used to identify the oxidation state and mineralogy within the experimentally synthesized and diagenetically transformed minerals, and map end-member solid phases within the grain mounts using the multiple energy maps. Metal-free FeSm transformed to pyrite, with residual FeS m detectable. Co- and Ni-containing FeS m also transformed to pyrite, but with multiple techniques detecting FeS m as well as S 0 , implying less complete transformation to pyrite as compared to metal-free FeS m . These results indicate that Co and Ni may inhibit transformation for FeS m to pyrite, or slow it down. Cobalt concentrations in the solid diminished by 30% during pyrite transformation, indicating that pyrite Co may be a conservative tracer of seawater or porewater Co concentrations. Nickel concentrations increased several-fold after pyrite formation, suggesting that pyrite may have scavenged Ni from the dissolution of primary FeS m grains. Lastly, nickel in pyrites thus may not be a reliable proxy for seawater or porewater metal concentrations.

58 GEOSCIENCES↗

Insights on the dissolution of water in an albite melt at high pressures and temperatures from a direct structural analysis

The water dissolution mechanism in silicate melts under high pressures is not well understood. Here we present the first direct structure investigation of a water-saturated albite melt to monitor the interactions between water and the network structure of silicate melt at the molecular level. In situ high-energy X-ray diffraction was carried out on the NaAlSi 3 O 8 -H 2 O system at 800 °C and 300 MPa, at the Advanced Photon Source synchrotron facility. The analysis of the X-ray diffraction data was augmented with classical Molecular Dynamics simulations of a hydrous albite melt, incorporating accurate water-based interactions. The results show that metal–oxygen bond breaking at the bridging sites occurs overwhelmingly at the Si site upon reaction with H 2 O, with subsequent Si–OH bond formation and negligible Al–OH formation. Furthermore, we see no evidence for the dissociation of the Al 3+ ion from the network structure upon breaking of the Si–O bond in the hydrous albite melt. The results also indicate that the Na + ion is an active participant in the modifications of the silicate network structure of the albite melt upon water dissolution at high P–T conditions. We do not find evidence for the Na + ion dissociating from the network structure upon depolymerization and subsequent formation of NaOH complexes. Instead, our results show that the Na + ion persists as a structure modifier with a shift away from Na–BO bonding to an increase in the extent of Na-NBO bonding, in parallel with pronounced depolymerization of the network. Our MD simulations show that the Si–O and Al–O bond lengths are expanded by about 6% in the hydrous albite melt compared to those of the dry melt at high P–T conditions. The changes in the network silicate structure of a hydrous albite melt at high pressure and temperature, as revealed in this study, must be considered in the advancement of water dissolution models of hydrous granitic (or alkali aluminosilicate) melts.

36 MATERIALS SCIENCE↗

Structural uniformity and compositional homogeneity of solid-phase alloyed rod

Solid-phase processes have emerged as an alternative to fusion-based alloying to avoid coarse microstructures, undesirable phase formation, and high energy consumption. However, achieving uniform distribution of alloying elements during friction-based processing remains challenging due to highly heterogeneous thermomechanical conditions. This work evaluates the structural uniformity and compositional homogeneity of Al–Cu–Zn alloyed rods produced by friction extrusion (FE) and establishes the role of the rotational speed to feed rate ratio (N/V) on alloying effectiveness. A systematic matrix of FE experiments was conducted at constant extrusion ratio with N/V values ranging from 3.7 to 300. Compositional uniformity was assessed along the rod length (ICP-OES), in three dimensions (X-ray computed tomography), and at the microscale (SEM–EDS), supported by a gray-level co-occurrence matrix (GLCM)–based homogeneity metric. Smoothed particle hydrodynamics (SPH) simulations were used to reveal material flow and thermomechanical fields. Results show that N/V = 100 produces a high-shear mixing zone that eliminates the unmixed core and enables near-full dissolution and dispersion of Cu and Zn. At lower N/V, a laminar flow region persists at the rod center, causing segregation and large composition gradients. The combined experimental–computational analysis provides mechanistic insight into the transition from fragmented particle dispersion to thermomechanically assisted metallurgical mixing. This study establishes processing–structure relationships for solid-phase alloying and provides guidance for achieving homogenized compositions comparable to wrought alloys via rapid, scalable FE processing.

Aluminum↗

Passivation dynamics in the anisotropic deposition and stripping of bulk magnesium electrodes during electrochemical cycling

Rechargeable magnesium (Mg) batteries show promise for use as a next generation technology for high-density energy storage, though little is known about the Mg anode solid electrolyte interphase and its implications for the performance and durability of a Mg-based battery. We explore in this report passivation effects engendered during the electrochemical cycling of a bulk Mg anode, characterizing their influences during metal deposition and dissolution in a simple, nonaqueous, Grignard electrolyte solution (ethylmagnesium bromide, EtMgBr, in tetrahydrofuran). Scanning electron microscopy images of Mg foil working electrodes after electrochemical polarization to dissolution potentials show the formation of corrosion pits. The pit densities so evidenced are markedly potential-dependent. When the Mg working electrode is cycled both potentiostatically and galvanostatically in EtMgBr these pits, formed due to passive layer breakdown, act as the foci for subsequent electrochemical activity. Detailed microscopy, diffraction, and spectroscopic data show that further passivation and corrosion results in the anisotropic stripping of the Mg {0001} plane, leaving thin oxide-comprising passivated side wall structures that demark the {0001} fiber texture of the etched Mg grains. Upon long-term cycling, oxide side walls formed due to the pronounced crystallographic anisotropy of the anodic stripping processes, leading to complex overlay anisotropic, columnar structures, exceeding 50 μm in height. Finally, the passive responses mediating the growth of these structures appear to be an intrinsic feature of the electrochemical growth and dissolution of Mg using this electrolyte.

36 MATERIALS SCIENCE↗

ANALYSIS OF SAMPLES FROM TANK 5F CHEMICAL CLEANING

The Savannah River Site (SRS) is preparing Tank 5F for closure. The first step in preparing the tank for closure is mechanical sludge removal. Following mechanical sludge removal, SRS performed chemical cleaning with oxalic acid to remove the sludge heel. Personnel are currently assessing the effectiveness of the chemical cleaning. SRS personnel collected liquid samples during chemical cleaning and submitted them to Savannah River National Laboratory (SRNL) for analysis. Following chemical cleaning, they collected a solid sample (also known as 'process sample') and submitted it to SRNL for analysis. The authors analyzed these samples to assess the effectiveness of the chemical cleaning process. The conclusions from this work are: (1) With the exception of iron, the dissolution of sludge components from Tank 5F agreed with results from the actual waste demonstration performed in 2007. The fraction of iron removed from Tank 5F by chemical cleaning was significantly less than the fraction removed in the SRNL demonstrations. The likely cause of this difference is the high pH following the first oxalic acid strike. (2) Most of the sludge mass remaining in the tank is iron and nickel. (3) The remaining sludge contains approximately 26 kg of barium, 37 kg of chromium, and 37 kg of mercury. (4) Most of the radioactivity remaining in the residual material is beta emitters and {sup 90}Sr. (5) The chemical cleaning removed more than {approx} 90% of the uranium isotopes and {sup 137}Cs. (6) The chemical cleaning removed {approx} 70% of the neptunium, {approx} 83% of the {sup 90}Sr, and {approx} 21% of the {sup 60}Co. (7) The chemical cleaning removed less than 10% of the plutonium, americium, and curium isotopes. (8) The chemical cleaning removed more than 90% of the aluminium, calcium, and sodium from the tank. (9) The cleaning operations removed 61% of lithium, 88% of non-radioactive strontium, and 65% of zirconium. The {sup 90}Sr and non-radioactive strontium were measured by different methods, and the differences in the fraction removed are not statistically significant. (10) Chemical cleaning removed 10-50% of the barium, chromium, iron, magnesium, manganese, and silicon. (11) Chemical cleaning removed only {approx}1% of the nickel.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Recalculating Dissolver Curves for Critical Parameters for Nuclear Criticality Safety

The dissolver paradox is a phenomenon in criticality safety whereby a high density fissile material is being dissolved in a low fissile density solution and is subcritical before and after dissolution. However, as the metal is being dissolved, there may be an intermediate concentration that leads to a critical state. CCG-184 is a Y-12 report written in 1980 that provided critical parameter data for two separate dissolver paradox scenarios: solid metal spheres and hollow metal spheres with internal moderation effects. The sphere and shell are both surrounded by solution, however the shell contains solution of the same concentration within itself. In 1980, there are limitations to the computational methods to determine critical parameters. These are due to the lower number of energy groups utilized (16-group) at the time, smaller number of established cross-sectional data, as well as a larger uncertainty within the resonance region of neutron energies. With these constraints in mind, these critical parameters are recalculated with newer cross-sectional data, a newer Monte Carlo code: SCALE 6.1.3 using KENO V.a, and a larger number of energy bins.

61 RADIATION PROTECTION AND DOSIMETRY↗

Potential-pH diagrams considering complex oxide solution phases for understanding aqueous corrosion of multi-principal element alloys

The potential-pH diagram, a graphical representation of the thermodynamically predominant reaction products in aqueous corrosion, is originally proposed for the corrosion of pure metals. The original approach only leads to stoichiometric oxides and hydroxides as the oxidation products. However, numerous experiments show that non-stoichiometric oxide scales are prevalent in the aqueous corrosion of alloys. In the present study, a room temperature potential-pH diagram considering oxide solid solutions, as a generalization of the traditional potential-pH diagram with stoichiometric oxides, is constructed for an FCC single-phase multi-principal element alloy (MPEA) based on the CALculation of PHAse Diagram method. The predominant reaction products, the ions in aqueous solution, and the cation distribution in oxides are predicted. The oxide solid solution is stabilized by the mixing free energy (or mixing entropy) and the stabilizing effect becomes more significant as the temperature increases. Consequently, solid solution oxides are stable in large regions of the potential-pH diagram and the mixing free energy mostly affects the equilibrium composition of the stable oxides, while the shape of stable regions for oxides is mostly determined by the structure of the stable oxides. Agreements are found for Ni 2+ , Fe 2+ , and Mn 2+ between the atomic emission spectroelectrochemistry measurements and thermodynamic calculations, while deviations exist for Cr 3+ and Co 2+ possibly due to surface complexation with species such as Cl - and the oxide dissolution. By incorporating the solution models of oxides, the current work presents a general and more accurate way to analyze the reaction products during aqueous corrosion of MPEAs.

Materials Science↗

DWPF DECON FRIT SUPERNATE ANALYSIS

The Savannah River National Laboratory (SRNL) has been requested to perform analyses on samples of the Defense Waste Processing Facility (DWPF) decon frit slurry (i.e., supernate samples and sump solid samples). Four 1-L liquid slurry samples were provided to SRNL by Savannah River Remediation (SRR) from the 'front-end' decon activities. Additionally, two 1-L sump solids samples were provided to SRNL for compositional and physical analysis. This report contains the results of the supernate analyses, while the solids (sump and slurry) results will be reported in a supplemental report. The analytical data from the decon frit supernate indicate that all of the radionuclide, organic, and inorganic concentrations met the limits in Revision 4 of the Effluent Treatment Plant (ETP) Waste Acceptance Criteria (WAC) with the exception of boron. The ETP WAC limit for boron is 15.0 mg/L while the average measured concentration (based on quadruplicate analysis) was 15.5 mg/L. The measured concentrations of Li, Na, and Si were also relatively high in the supernate analysis. These results are consistent with the relatively high measured value of B given the compositional make-up of Frit 418. Given these results, it was speculated that either (a) Frit 418 was dissolving into the supernate or aqueous fraction and/or (b) fine frit particulates were carried forward to the analytical instrument based on the sampling procedure used (i.e., the supernate samples were not filtered - only settled with the liquid fraction being transferred with a pipette). To address this issue, a filtered supernate sample (using a 0.45 um filter) was prepared and submitted for analysis. The results of the filtered sample were consistent with 'unfiltered or settled' sample - relatively high values of B, Li, Na, and Si were found. This suggests that Frit 418 is dissolving in the liquid phase which could be enhanced by the high surface area of the frit fines or particulates in suspension. Based on the results of this study, it is recommended that DWPF re-evaluate the technical basis for the B WAC limit (the only component that exceeds the ETP WAC limit from the supernate analyses) or assess if a waiver or exception can be obtained for exceeding this limit. Given the possible dissolution of B, Li, Na, and Si into the supernate (due to dissolution of frit), DWPF may need to assess if the release of these frit components into the supernate are a concern for the disposal options being considered. It should be noted that the results of this study may not be representative of future decon frit solutions or sump/slurry solids samples. Therefore, future DWPF decisions regarding the possible disposal pathways for either the aqueous or solid portions of the Decon Frit system need to factor in the potential differences. More specifically, introduction of a different frit or changes to other DWPF flowsheet unit operations (e.g., different sludge batch or coupling with other process streams) may impact not only the results but also the conclusions regarding acceptability with respect to the ETF WAC limits.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Melting/freezing points of high concentrations of AlCl 3 in a saturated chloroaluminate ionic liquid

Melting/freezing points of AlCl 3 in saturated chloroaluminate ionic liquids [molar ratio 2:1 AlCl 3 :1-ethyl-3-methyl imidazolium chloride (EMIC)] are measured by differential scanning calorimetry (DSC). A critical range of temperature data (50-130 °C) for AlCl 3 dissolution and precipitation from saturated chloroaluminate ionic liquids is obtained. This range of temperature data is of significance to control phase transition of AlCl 3 in saturated chloroaluminate ionic liquids. By applying the chloroaluminate ionic liquids to electrolytes for energy storage usage, solid AlCl 3 can be partially dissolved and precipitated out during the charging/discharging cycle of energy storage equipment. Furthermore, the energy density of the electrolytes is expected to be greatly improved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical Analysis of the Source of Excessive Na + and Cl &ndash; Species in Flowback Water From Hydraulically Fractured Shale Formations

Fracture fluid comprises fresh water, proppant, and a small percentage of other additives, which support the hydraulic fracturing process. Excluding situations in which flowback water is recycled and reused, total dissolve solids in fracture fluid is limited to the fluid additives, such as potassium chloride (1-7 weight percent KCL), which is used as a clay stabilizer to minimize clay swelling, and clay particle migration. However, the composition of recovered fluid, especially as it relates to the total dissolve solids (TDS), is always substantially different than the injected fracture fluid. The ability to predict flowback water volume and composition is useful when planning for the management or reuse of this aqueous byproduct stream. In this work, an ion transport and halite dissolution model was coupled with a fully implicit, dual porosity, numerical simulator, to study the source of the excess solutes in flowback water, and to predict the concentration of both Na+ and Cl- species seen in recovered water. The results showed that mixing alone, between the injected fracture fluid and concentrated in situ formation brine, could not account for the substantial rise in TDS seen in flowback water. Instead, the results proved that halite dissolution is a major contributor to the change in TDS seen in fracture fluid during injection and recovery. Halite dissolution can account for as much as 81% of Cl- and 86.5% of Na+ species seen in 90-day flowback water; mixing, between the injected fracture fluid and in situ concentrated brine, accounts for approximately 19% Cl- and 13% Na+.

03 NATURAL GAS↗

Geochemical modeling of leaching of Ca, Mg, Al, and Pb from cementitious waste forms

Results from extraction tests on cement-waste samples were simulated with a thermodynamic equilibrium model using a consistent database, to which lead data were added. Subsequent diffusion tests were modeled by means of a 3D diffusive transport model combined with the geochemical model derived from the extraction tests. Modeling results of the leached major element concentrations for both uncarbonated and (partially) carbonated samples agreed well with the extraction test using the set of pure minerals and solid solutions present in the database. The observed decrease in Ca leaching with increasing carbonation level was qualitatively predicted. Simulations also revealed that Pb leaching is not controlled by dissolution/precipitation only. The addition of the calcite-cerrusite solid solution and adsorption reactions on amorphous Fe- and Al-oxides improved the predictions and are considered to control the Pb leaching during the extractions tests. The dynamic diffusive leaching tests were appropriately modeled for Na, K, Ca and Pb.

36 MATERIALS SCIENCE↗

Mineralogy and pore water chemistry of a boiler ash from a MSW fluidized-bed incinerator

This paper presents an investigation of the mineralogy and pore water chemistry of a boiler ash sampled from a municipal solid waste fluidized-bed incinerator, subject to 18 months of dynamic leaching in a large percolation column experiment. A particular focus is on the redox behaviour of Cr(VI) in relation to metal aluminium Al{sup 0}, as chromium may represent an environmental or health hazard. The leaching behaviour and interaction between Cr(VI) and Al{sup 0} are interpreted on the basis of mineralogical evolutions observed over the 18-month period and of saturation indices calculated with the geochemical code PhreeqC and reviewed thermodynamic data. Results of mineralogical analyses show in particular the alteration of mineral phases during leaching (e.g. quartz and metal aluminium grains), while geochemical calculations suggest equilibria of percolating fluids with respect to specific mineral phases (e.g. monohydrocalcite and aluminium hydroxide). The combination of leaching data on a large scale and mineralogical analyses document the coupled leaching behaviour of aluminium and chromium, with chromium appearing in the pore fluids in its hexavalent and mobile state once metal aluminium is no longer available for chromium reduction.

54 ENVIRONMENTAL SCIENCES↗

Reactivity of Redox Cycled Fe-bearing Subsurface Sediments Towards Hexavalent Chromium Reduction

Structural Fe(II) in clay minerals and natural sediments is known to reduce Cr(VI) to Cr(III), but the effect of redox-cycled Febearing natural sediments on Cr(VI) reduction kinetics is poorly understood. The objective of this study was to understand the kinetics and mechanisms of Cr(VI) reduction by Fe(II) in redox cycled natural sediment. Fe-bearing sediment was collected from the Ringold formation in the 300 area of Hanford, Washington, United States. Fe redox cycling of the sediment was accomplished via four cycles of bioreduction of structural Fe(III) in Hanford sediment and air oxidation of the resulting Fe(II). Bio-produced Fe(II) in Hanford sediment from each redox cycle was utilized to reduce Cr(VI) at three temperatures (10, 20 and 30° C). The initial rate of Cr(VI) reduction generally increased with each redox cycle, which was more pronounced at high temperatures. The amount of Fe(II) oxidized to the amount of Cr(VI) reduced was close to the expected stoichiometric ratio of 3. Aqueous concentrations of Si, Al, and Fe revealed some dissolution of the sediment after reaction with Cr(VI). Xray diffraction (XRD) and scanning electron microscopy (SEM) detected secondary mineral formation. Mössbauer data showed that the oxidation of Fe(II) was coupled with the reduction of Cr(VI) but no Feoxides/ oxyhydroxides formed. Transmission electron microscopy (TEM), electron energy loss spectroscopy (EELS), XANES, and EXAFS were performed for representative reduced Cr solids that formed from reduction of Cr(VI) by sediment-associated Fe(II) at 30oC. TEM revealed that the d-spacing of Cr-reacted montmorillonite at 30° C, a dominant Fe-bearing mineral in Hanford sediment, expanded from 10 Å to 13 Å. This layer expansion was likely due to intercalation of reduced Cr(III) into the interlayer space of the montmorillonite structure. EELS exhibited an L2 absorption peak at 586.0 eV and an L3 absorption peak at 577.0 eV, suggestive of Cr(III) in a hydroxide mineral phase. Similarly, XANES and EXAFS analyses confirmed Cr(VI) reduction to Cr(OH)3 at 30° C and indicated an edge-sharing coordination of the Cr(III) octahedra to 2-3 other Cr or metal ions. This study has important implications for understanding the reactivity of clay-rich sediment towards Cr(VI) reduction at contaminated sites and the stability of the reduced Cr(III).

Bishop, Michael E.↗

Aluminum Coprecipitates with Fe (hydr)oxides: Does Isomorphous Substitution of Al3plus for Fe3plus in Goethite Occur

Iron (hydr)oxides are common in natural environments and typically contain large amounts of impurities, presumably the result of coprecipitation processes. Coprecipitation of Al with Fe (hydr)oxides occurs, for example, during alternating reduction-oxidation cycles that promote dissolution of Fe from Fe-containing phases and its re-precipitation as Fe-Al (hydr)oxides. We used chemical and spectroscopic analyses to study the formation and transformation of Al coprecipitates with Fe (hydr)oxides. In addition, periodic density functional theory (DFT) computations were performed to assess the structural and energetic effects of isolated or clustered Al atoms at 8 and 25 mol% Al substitution in the goethite structure. Coprecipitates were synthesized by raising the pH of dilute homogeneous solutions containing a range of Fe and Al concentrations (100% Fe to 100% Al) to 5. The formation of ferrihydrite in initial suspensions with {<=}20 mol% Al, and of ferrihydrite and gibbsite in initial suspensions with {>=}25 mol% Al was confirmed by infrared spectroscopic and synchrotron-based X-ray diffraction analyses. While base titrations showed a buffer region that corresponded to the hydrolysis of Fe in initial solutions with {<=}25 mol% Al, all of the Al present in these solutions was retained by the solid phases at pH 5, thus indicating Al coprecipitation with the primary Fe hydroxide precipitate. In contrast, two buffer regions were observed in solutions with 30 mol% Al (at pH {approx}2.25 for Fe{sup 3+} and at pH {approx}4 for Al{sup 3+}), suggesting the formation of Fe and Al (hydr)oxides as two separate phases. The Al content of initial coprecipitates influenced the extent of ferrihydrite transformation and of its transformation products as indicated by the presence of goethite, hematite and/or ferrihydrite in aged suspensions. DFT experiments showed that: (i) optimized unit cell parameters for Al-substituted goethites (8 and 25 Mol% Al) in clustered arrangement (i.e., the formation of diaspore-like clusters) were in good agreement with available experimental data whereas optimized unit cell parameters for isolated Al atoms were not, and (ii) Al-substituted goethites with Al in diaspore-like clusters resulted in more energetically favored structures. Combined experimental and DFT results are consistent with the coprecipitation of Al with Fe (hydr)oxides and with the formation of diaspore-like clusters, whereas DFT results suggest isomorphous Al for Fe substitution within goethite is unlike at 8 mol% Al substitution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

In situ Investigation of Water Interaction with Lead-Free All Inorganic Perovskite (Cs 2 SnI x Cl 6– x )

Hybrid halide perovskites display a great tunability of optoelectronic properties and environmental stability by controlling the halogen anions (e.g., I, Cl, and Br). Yet, their water interaction and degradation mechanisms are not completely elucidated. In this work, the interaction of Cs 2 SnCl 6 and Cl-enriched solid solution Cs 2 SnI 0.9 Cl 5.1 with water was systematically studied by in situ synchrotron X-ray diffraction and micro-Raman spectra and compared with the isostructural Cs 2 SnI 6 . Unlike Cs 2 SnI 6 , which experiences a direct dissolution in water, Cs 2 SnCl 6 displays an enhanced stability and the dissolution of the Cs 2 SnCl 6 accompanies with the formation of an amorphous alteration phase. Under controlled dehydration conditions, two-dimensional Cs 2 SnCl 6 flakes can be precipitated out from water solution. Moreover, the mixed halide perovskite (Cs 2 SnI 0.9 Cl 5.1 ) experiences fast iodide dissolution in water solution and transforms to a more chloride-enriched perovskite which shows a behavior similar to Cs 2 SnCl 6 . The mechanistic understanding of the dissolution–precipitation process of Cs 2 SnI x Cl 6–x perovskites is useful for developing new perovskites with varied halogen and controlled environmental stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantification of Electrochemical Nanoscale Processes in Lithium Batteries By OperandoEC-(S)TEM

Lithium (Li)-ion batteries are currently used for a wide variety of portable electronic devices, electric vehicles and renewable energy applications. In addition, extensive worldwide research efforts are now being devoted to more advanced “beyond Li-ion” battery chemistries - such as lithium-sulfur (Li-S) and lithium-air (Li-O2) - in which the carbon anode is replaced with Li metal. However, the practical application of Li metal anode systems has been highly problematic. The main challenges involve controlling the formation of a solid-electrolyte interphase (SEI) layer and the suppression of Li dendrite growth during the charge/discharge process (achieving “dendrite-free” cycling). The SEI layer formation continuously consumes the electrolyte components creating highly resistive layer, which leads to the rapid decrease of cycling performance and degradation of the Li anode. The growth of Li metal dendrites at the anode contributes to rapid capacity fading (the presence of “dead Li” created during the discharge leads to an increased overpotential) and, in the case of continuous growth, leads to internal short circuits and extreme safety issues. Here we demonstrate the application of an operando electrochemical scanning transmission electron microscopy (ec-(S)TEM) cell to study the SEI layer formation and the initial stages of Li dendrite growth - the goal is to develop a mechanism for mitigating the degradation processes and increasing safety. Bright field (BF) STEM images in Figure 1 A-C show Li metal deposition and dissolution processes at the interface between the Pt working electrode and the lithium hexafluorophosphate (LiPF6) in propylene carbonate (PC) electrolyte during three charge/discharge cycles. A contrast reversal caused by Li metal being lighter/less dense than surrounding electrolyte (Li appears brighter than the background in BF STEM images) allows Li to be uniquely identified from the other components in the system - the only solid material that is less dense than the electrolyte is Li metal. Using these images, we can precisely quantify the total volume of Li deposition, the thickness of the SEI layer (observed as a ring of positive contrast around the electrode) and alloy formation due to Li+ ion insertion during each cycle. Furthermore, at the end of each discharge cycle we can quantify the presence of “dead Li” detached from the Pt electrode, thereby demonstrating the degree of irreversibility (and degradation of Pt electrode) associated with insertion/removal of Li+during this process with direct correlation to electrochemical performance. Such analyses provide significant insights into Li metal dendrite growth, which is critical to understand the complex interfacial reactions needed to be controlled for future Li-based and next generation energy storage systems.

batteries↗